SEARCH · Engineering Papers

Results for “matrix power”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

All sources NASA NTRS DOE OSTI

DOE OSTI2022

Sodium diffusion in heterogeneous porous media: Connecting laboratory experiments and simulations

Sodium has been suggested as a tracer for brine in reservoir formations where a significant amount of sodium ion is found mainly in the aqueous phase. Fortunately, the most abundant sodium isotope, 23 Na, is Nuclear Magnetic Resonance (NMR) active, making it possible to study the structure and dynamical properties of both bulk and pore confined fluid systems. We investigated the diffusion of key dissolved sodium species in bulk solution and porous media as a function of composition, ionic strength, and permeability of the carbonate samples using NMR relaxometry and pulsed-field gradient (PFG) NMR techniques. We use Indiana limestone as an example of natural porous media and water as a freely diffusible tracer and carrier. We demonstrate apparent diffusion measurement of sodium based on changes in spin–spin relaxation time (T 2 ) signal in pore confinement. The diffusion rate of sodium decreases with increasing counter-ion size. This effect is greater at higher ionic strengths and lower chemical potentials in porous media. The reactive transport code, CrunchFlow, was used to complement the NMR experiments to simulate diffusion behavior in porous media. Combining these two methods provides a powerful approach to estimating effective diffusion coefficients in heterogeneous matrices. The modeling considers the influence of physical properties (porosity and tortuosity) and chemical properties (geochemical composition and chemical gradients). The results presented in this work highlight the advantage of measuring apparent diffusivity using NMR T 2 relaxometry in conjunction with numerical simulation to derive effective diffusivity and the corresponding matrix properties (i.e., tortuosity) of the system.

58 GEOSCIENCES↗

DOE OSTI2020

Long short-term memory embedded nudging schemes for nonlinear data assimilation of geophysical flows

Reduced rank nonlinear filters are increasingly utilized in data assimilation of geophysical flows, but often require a set of ensemble forward simulations to estimate forecast covariance. On the other hand, predictor-corrector type nudging approaches are still attractive due to their simplicity of implementation when more complex methods need to be avoided. However, optimal estimate of nudging gain matrix might be cumbersome. In this paper, we put forth a fully nonintrusive recurrent neural network approach based on a long short-term memory (LSTM) embedding architecture to estimate the nudging term, which plays a role not only to force the state trajectories to the observations but also acts as a stabilizer. Furthermore, our approach relies on the power of archival data and the trained model can be retrained effectively due to power of transfer learning in any neural network applications. In order to verify the feasibility of the proposed approach, we perform twin experiments using Lorenz 96 system. Our results demonstrate that the proposed LSTM nudging approach yields more accurate estimates than both extended Kalman filter (EKF) and ensemble Kalman filter (EnKF) when only sparse observations are available. With the availability of emerging AI-friendly and modular hardware technologies and heterogeneous computing platforms, we articulate that our simplistic nudging framework turns out to be computationally more efficient than either the EKF or EnKF approaches.

42 ENGINEERING↗

DOE OSTI2024

Classical shadows for quantum process tomography on near-term quantum computers

Quantum process tomography is a powerful tool for understanding quantum channels and characterizing the properties of quantum devices. Inspired by recent advances using classical shadows in quantum state tomography [H.-Y. Huang, R. Kueng, and J. Preskill, .], we have developed ShadowQPT, a classical shadow method for quantum process tomography. We introduce two related formulations with and without ancilla qubits. ShadowQPT stochastically reconstructs the Choi matrix of the device allowing for an classical evaluation of the device on arbitrary inputs with respect to arbitrary outputs. Using shadows, we then show how to compute overlaps, generate all k -weight reduced processes, and perform reconstruction via Hamiltonian learning. These latter two tasks are efficient for large systems as the number of quantum measurements needed scales only logarithmically with the number of qubits. A number of additional approximations and improvements are developed, including the use of a pair-factorized Clifford shadow and a series of postprocessing techniques that significantly enhance the accuracy for recovering the quantum channel. We have implemented ShadowQPT using both Pauli and Clifford measurements on the IonQ trapped ion quantum computer for quantum processes up to n = 4 qubits, and we achieved good performance. Published by the American Physical Society 2024

Levy, Ryan (ORCID:0000000349527156)↗

DOE OSTI2021

Gapless spin liquid and pair density wave of the Hubbard model on three-leg triangular cylinders

We study the ground state properties of the Hubbard model on three-leg triangular cylinders using large-scale density-matrix renormalization group simulations. At half-filling, we identify an intermediate gapless spin liquid phase, which has one gapless spin mode and algebraic spin–spin correlations but exponential decay scalar chiral–chiral correlations, between a metallic phase at weak coupling and Mott insulating dimer phase at strong interaction. Upon light doping the gapless spin liquid, the system exhibits power-law charge-density-wave (CDW) correlations but short-range single-particle, spin–spin, and chiral–chiral correlations. Similar to CDW correlations, the superconducting correlations also decay in power-law but oscillate in sign as a function of distance, which is consistent with the striped pair-density wave. When further doping the gapless spin liquid phase or doping the dimer order phase, another phase takes over, which has similar CDW correlations but all other correlations decay exponentially.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2020

Demonstration of Embedded Sensors in Ceramic Structures

The Transformational Challenge Reactor (TCR) program seeks to demonstrate an advanced 3D printed nuclear reactor core. A binder jet additive manufacturing process is used to fabricate the complex SiC ceramic components of the TCR core. After printing, the components are densified via chemical vapor infiltration (CVI). This process allows complex cavities to be created in which sensors can be placed at strategic locations. Inserting the sensors during the CVI process allows the sensors to be embedded within the component as it is infiltrated. The primary challenge for embedding the sensors is identifying the sensors and sensor sheath materials that can survive the temperatures (>1,000°C) and chemical exposure to H 2 and HCl during CVI. The embedded sensors that are being investigated for use during TCR operation include thermocouples, self-powered neutron detectors, and spatially distributed fiber-optic temperature sensors. This report describes the CVI materials compatibility tests and initial trials for embedding functional sensors. Mo is identified as the most suitable sensor sheath material based on its availability in small diameter tubing, relatively low neutron absorption cross section, and compatibility with H 2 , HCl, and the surrounding SiC matrix at the process temperatures. Amorphous SiO2 fiber-optic samples with Au and Cu metal coatings were successfully embedded in SiC along with bare fibers, although the metal coatings showed some evidence of localized melting during CVI. Initial experiments attempting to embed functional sensors showed that the sensors can be embedded in 3D printed SiC parts, but there are still challenges that must be overcome to ensure that the sensors and sensor sheaths do not fail during CVI. In particular, Nb-sheathed Mo-Nb thermocouples failed at temperatures far lower than expected despite thermodynamic calculations and materials compatibility tests that show the Nb sheath to be compatible with the CVI environment. One potential explanation for the large expansion of the Nb sheath could be related to hydride formation in the lower temperature region of the sheath. Future work will focus on Mo-sheathed thermocouples instead of Nb. The fiberoptic sensors tested during the instrumented experiment broke due to the lack of mechanical protection after their polymer-based coatings were vaporized. Future instrumented experiments will use metal-coated optical fibers for strain sensing to provide additional mechanical protection. However, custom coatings with higher melting points than commercially available Au and Cu might be required. Regardless, fiber-optic sensors are still candidates for spatially distributed temperature measurements since they can be inserted into an embedded metal sheath after CVI.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2024

Adaptive Methods for Radial Basis Functions

Radial basis functions (RBFs) are a powerful tool for constructing high-order accurate reduced representations of scattered data in arbitrary dimension and on manifolds. We present a method of constructing data approximations in which we utilize a functional tail to capture a global background profile and a RBF neural network (NN) to capture the smaller-scale features. In the RBF NN the RBF centers, matrix shape parameters were selected adaptively for each RBF. We also utilized a geodesic notion of distance on the manifold on which the data lies, e.g., the spherical geodesic for data on the sphere. Although each of these ideas have been been investigated separately in previous works, their combination into a single algorithm is novel. We defined a machine learning problem in which these properties are learned to minimize the data reduction error. We demonstrate the algorithm for applications of scattered data reduction in the plane and on the sphere.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2023

Robust Statistical Approach for Determination of Graphite Nitridation Using Bayesian Model Comparison

A better estimation of surface reaction efficiency of semiconductor-grade graphite with atomic nitrogen, as well as the calibration error are calculated using Bayesian updating based on experimental data. Compared with a conventional deterministic model, the stochastic model approach is a powerful tool in the sense that the model is capable of taking into account underlying error correlations among the data quantities. In this paper, we investigate four different stochastic models (called “stochastic system model classes” herein) corresponding to different descriptions of modeling and measurement error structures, given one deterministic physical model. These stochastic system model classes differ in the covariance matrix structure that is used in the uncertainty model to represent uncertainties associated with the physical model and experimental measurements. For each model class, Bayesian inference is used to estimate the posterior probabilities of the physical model parameters as well as of the stochastic model parameters. Model comparison and selection are then applied based on two measures including Bayesian evidence and Bayesian information criterion, as well as the deviance information criterion. Both measures suggest the stochastic model class, which considers that a correlation between errors in two data quantities among different data points is the most plausible. With the stochastic model class, the range of uncertainty in surface reaction efficiency is estimated to be about two orders of magnitude at [Formula: see text].

Engineering↗

DOE OSTI2022

Microstructural and nanomechanical studies of PVD Cr coatings on SiC for LWR fuel cladding applications

The microstructure and nanomechanical properties of pure Cr coatings deposited on SiC with various physical vapor deposition (PVD) methods have been investigated for the mitigation of hydrothermal corrosion of SiC-SiC f (SiC fiber-reinforced SiC matrix) composite fuel cladding in light water reactors (LWR). Cr coatings (4–7 μm thick) were deposited on unbiased SiC substrates using six variants of magnetron sputtering processes: (i) standard (S-DCMS), (ii) pulsed (P-DCMS), (iii) ion-assisted (I-DCMS), and (iv) pulsed ion-assisted direct current magnetron sputtering (PI-DCMS), (v) high-power impulse magnetron sputtering (HiPIMS), and (vi) bipolar HiPIMS (B-HiPIMS). Microstructural characterization and nanoindentation testing were used to evaluate effects of deposition technique on coating microstructure and nanomechanical properties. The application of positive reverse pulses to the sputter target induced coarsening of the columnar grain structure, while ion bombardment of substrates during deposition promoted densification of the coating microstructure. Both effects are exemplified in B-HiPIMS deposition, resulting in a high-density microstructure with compressive residual stress. Material pile-up around nano-indents and plastic work during nanoindentation were analyzed to understand deformation behavior of the coatings. Finally, the results suggest the B-HiPIMS process to be among the promising methods for the deposition of Cr coatings on SiC-SiC f for LWR cladding application.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Dark energy survey year 3 results: cosmology from galaxy clustering and galaxy–galaxy lensing in harmonic space

We present the joint tomographic analysis of galaxy-galaxy lensing and galaxy clustering in harmonic space (HS), using galaxy catalogues from the first three years of observations by the Dark Energy Survey (DES Y3). We utilize the redMaGiC and MagLim catalogues as lens galaxies and the metacalibration catalogue as source galaxies. The measurements of angular power spectra are performed using the pseudo-$C_\ell$ method, and our theoretical modelling follows the fiducial analyses performed by DES Y3 in configuration space, accounting for galaxy bias, intrinsic alignments, magnification bias, shear magnification bias and photometric redshift uncertainties. We explore different approaches for scale cuts based on non-linear galaxy bias and baryonic effects contamination. Our fiducial covariance matrix is computed analytically, accounting for mask geometry in the Gaussian term, and including non-Gaussian contributions and super-sample covariance terms. To validate our HS pipelines and covariance matrix, we used a suite of 1800 log-normal simulations. We also perform a series of stress tests to gauge the robustness of our HS analysis. In the $\Lambda$CDM model, the clustering amplitude $S_8 =\sigma _8(\Omega _m/0.3)^{0.5}$ is constrained to $S_8 = 0.704\pm 0.029$ and $S_8 = 0.753\pm 0.024$ (68 per cent C.L.) for the redMaGiC and MagLim catalogues, respectively. For the wCDM, the dark energy equation of state is constrained to $w = -1.28 \pm 0.29$ and $w = -1.26^{+0.34}_{-0.27}$, for redMaGiC and MagLim catalogues, respectively. These results are compatible with the corresponding DES Y3 results in configuration space and pave the way for HS analyses using the DES Y6 data.

(cosmology:) cosmological parameters↗

DOE OSTI2022

Modeling and Analysis of a Polyphase Wireless Power Transfer System for EV Charging Applications

Extreme fast charging is an emerging technology targeting to significantly decrease charging times of electric vehicles to 10–20 minutes, similar to an interstate gas refueling practice. High-power wireless power transfer (WPT) systems with polyphase electromagnetic couplers can be an attractive solution for these applications due to the very high surface power density of polyphase coils with reduced ripple current characteristics on both the primary and secondary sides that result in more compact designs with reduced dc bus bar capacitor requirements. In addition, WPT systems offer automated charging process, which can be an enabling technology for connected and automated vehicles, with high-efficiency, convenience, safety, and flexibility. This study presents a matrix representation of a mathematical model for a three-phase WPT system with series-series connected three-phase resonant compensation networks. Nonzero interphase mutual inductances between the same side phase windings are considered for tuning to obtain a circuit model for parametric sensitivity. Simulation and experimental results presented for a 50-kW experimental prototype to demonstrate the operation of the polyphase WPT system.

Zeng, Rong↗

DOE OSTI2023

Assessment of the Phase-to-Ground Fault Apparent Admittance Method with Phase/Ground Boundaries to Detect Types of Electrical Faults for Protective Relays Using Signature Library and Simulated Events

Protective relays in electric power grids recognize the types of electrical faults in a few seconds. The most common detection method to detect the types of electrical faults is based on measuring the angle between the zero and negative sequence currents. However, it is not completely accurate because the phase to phase ground and phase to ground electrical faults could have the same detection conditions. Therefore, engineers need to plot the events after an electrical fault to observe the nature of the incidents in detail. In this study, the phase to ground fault apparent (PGFA) admittance method with phase/ground boundaries identified the types of electrical faults located in distribution power lines and feeders. This method was based on measuring the PGFA admittance magnitudes for the faulted and non-faulted phases, resulting in greater than zero and near zero, respectively. The PGFA admittance algorithm was built with MATLAB/ Simulink software and tested with signature library and grid simulation events. The PGFA method with phase/ground boundaries was evaluated with the confusion matrix. The measured and predicted values matched in more than 90% of the tests, and the PGFA admittance method with phase/ground boundaries presented an accuracy of 94.3% and a precision of 100%.

Piesciorovsky, Emilio↗

DOE OSTI2024

Metal DiSulfide thin films synthesized by pulsed ion beam ablation: Self-assembled structures with improved mechanical properties in humid conditions

Thin films composed of transition metal dichalcogenides such as molybdenum disulfide (MoS 2 ) or tungsten disulfide (WS 2 ) are well known for their solid lubricating behavior in dry environments such as space, but deteriorate rapidly in environments where oxygen is present. There have been many attempts over recent decades to improve MoS 2 lubricating performance in humid environments by addition of metals such as titanium to the film. The additions have come in the form of co-sputtering with the MoS 2 , or formation of nano multilayer coatings. We have previously reported on the synthesis of MoS 2 films by high-power ion beam ablation [Prasad et al, Matls. Lett. 65 (2010) 4–6]. The resulting films are observed to contain spheres of pure Mo of 10–100 nm size evenly dispersed throughout the ~1 μm-thick film, a form of self-assembly not before seen in films produced by sputtering or by pulsed laser deposition (PLD). The remaining Mosingle bondS matrix was observed to crystalize in situ under frictional contact into MoS 2 with the basal planes orienting themselves in the direction of sliding underneath the wear surface. The present study concerns metal additions in the form of alternating layers with MoS 2 deposited in between from an ablation target. The addition of Ti resulted in the extension of good tribological performance to humid air conditions, but the path to good performance appears to be relatively narrow. The same distributed Mo spheres were present in the new film, and similar self-assembled morphologies when V was substituted for the Ti, and when multilayers were formed of WS 2 with Zr additions. Furthermore, it appears that addition of Ti resulted in improvements in mechanical film strength that contributed to the wear ability in humid conditions.

Intense ion beams↗

DOE OSTI2020

High-Precision Zinc Isotopic Measurement of Certified Reference Materials Relevant to the Environmental, Earth, Planetary and Biomedical Sciences

The zinc (Zn) stable isotope system has emerged as a powerful tool for investigating natural and anthropogenic processes of interest to disciplines extending from the Earth and planetary sciences to biomedical research. In nature, Zn isotopes typically fractionate ( 66 Zn/ 64 Zn) within the range of –1 and +1 permil (‰), and however, analytical limitations restrict the application of the Zn isotope system. Specifically, there is a lack of well-characterised matrix-matched reference materials covering most Zn isotope applications that are essential for validating laboratory performance, particularly given the contamination prone nature of Zn. Furthermore, the increasing demand for analysis of size-limited materials and sample types displaying small, sub-permil level Zn isotope variations requires improvements in measurement procedures. To address these limitations, the δ 66 Zn values of two pure Zn solutions and eighteen reference materials including the previously uncharacterised RGM-2, BCR-279, DOLT-4, DOLT-5, NASS-7, SBC-1, SGR-1b, MESS-3 and HISS-1, and the understudied QLO-1, SDC-1, BCR-414, NASS-6 and COQ-1 materials are reported. Furthermore, a 70 Zn- 67 Zn double-spike design has been implemented that routinely achieves intermediate measurement precision better than ± 0.02‰. This represents at least a two-fold improvement when compared with other double-spike designs, providing a robust platform of δ 66 Zn values required for quality control procedures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

BENEFIT with Northeastern University: HVAC Hardware-in-the-Loop Experimental Testing of a Heat Pump and Air Conditioner

This dataset includes HVAC Hardware-in-the-Loop (HIL) experimental results for a single stage, SEER 16, HSPF 9.5, 3-ton single-speed air source heat pump with 15 kW of backup auxiliary heating tested in both cooling and heating mode, and a two stage, SEER 21, 2-ton central air conditioner tested in cooling mode for a set of outdoor temperatures and indoor setpoint temperatures. In addition to these tests, experimental tests focused on the operation of auxiliary heating for the heat pump for winter condition were also conducted. The laboratory experiments for transient testing of the heat pump and air conditioner were conducted using the two HIL systems in the Systems Performance Laboratory (SPL) at NREL’s Energy Systems Integration Facility (ESIF). Further information on laboratory design and capabilities of the SPL along with the architecture of HVAC HIL system can be found in: Sparn, B. F. 2018. Laboratory Resources and Techniques to Evaluate Smart Home Technology (No. NREL/CP-5500-71696). National Renewable Energy Laboratory (NREL), Golden, CO (United States). https://www.nrel.gov/docs/fy18osti/71696.pdf and the experimental setup and validation of HVAC HIL platform can be found in: Ramaraj, S. and Sparn, B. 2022. Validation of HVAC Hardware-In-the-Loop Simulation for Advanced Control Strategies in Smart Homes (No. NREL/CP-5500-82562). National Renewable Energy Lab (NREL), Golden, CO (United States). https://www.nrel.gov/docs/fy22osti/82562.pdf. These experimental results can be used to validate how we currently model the cycling behavior of heat pumps and air conditioners. Additionally, many demand response programs implement heat pump and air conditioner control by changing the thermostat set point – these data may also be used to verify our models for heat pump and air conditioner demand response control are implemented correctly. The Test_Matrix file describes all the indoor and outdoor test conditions for heat pump and air conditioner and the file names of data sets include information about the test conditions. A wide range of outdoor air temperatures were chosen to accommodate summer and winter conditions. In addition to operating the HVAC equipment with different outdoor temperatures, we also operate the system with different indoor temperature set points to represent different grid signals or different operating conditions. For cooling conditions, the baseline set point is 72°F. To represent Load Up signals, the setpoint is changed to 68°F. The Load Shed set point is 76°F. For heating conditions, the baseline set point was assumed to be 68°F. The Load add set point is 72°F and the Load shed set point is 64°F. The starting indoor temperature for cooling conditions was set ~2°F above the indoor setpoint temperature so that the equipment turned on quickly. Similarly, the initial indoor temperature was set ~2°F lower than setpoint for heating mode tests to ensure that heating began quickly. The return air temperature was assumed to be equal to the indoor setpoint temperature in all cases. The experimental data are sampled at 1-second intervals. The data from ecobee thermostat at 5-minute interval are resampled and added to the corresponding file. The content of each data set is as follows: • T_Return (C): Measured return air temperature [C] • T_Return_SP (C): Return air temperature setpoint from E+ model, sent to HIL [C] • T_Supply (C): Measured supply air temperature at evaporator outlet [C] • T_Outdoor (C): Measured outdoor air temperature [C] • T_Outdoor_SP (C): Outdoor air temperature setpoint from weather file, sent to HIL [C] • T_Indoor (C): Measured indoor air temperature [C] • T_Indoor_SP (C): Indoor air temperature setpoint from E+ model, sent to HIL [C] • Outdoor Unit Power (W): Measured power of the outdoor unit [W] • Indoor Unit Power (W): Measured power of the indoor unit [W] • Evaporator Airflow Rate (CFM): Measured evaporator or indoor unit airflow rate sent to E+ model [CFM] • Cooling/Heating Capacity (kW): Calculated cooling/heating capacity sent to E+ model [kW] • T_SP_Thermostat (C): Thermostat cooling/heating setpoint temperature [C] • T_Indoor_Thermostat (C): Thermostat indoor air temperature [C]

24 POWER TRANSMISSION AND DISTRIBUTION↗

DOE OSTI2020

Thermal shock resistance of multilayer silicon carbide receiver tubes for 800°C molten salt concentrating solar power application

CSP power tower receiver systems during rapid transient weather periods can be vulnerable to thermal shock conditions from rain that which can facilitate the onset of leaks and failures that can have catastrophic consequences. Silicon carbide (SiC) materials have attractive receiver application characteristics for being light weight, having high-strength and excellent thermal shock resistance performance which make them a particularly good fit for receiver absorber materials in CSP. In this investigation, the performance characteristics of Ceramic Tubular Products (CTP) SiC ceramic matrix composite (CMC), multilayered tubes were explored with respect to thermal shock performance for solar receiver applications in next generation CSP plants. Here, thermal shock testing was performed at the Sandia National Laboratories (SNL) Solar Furnace facility using a dynamic stage and thermal shock tube test setup. The tubes tested under incident solar heat flux of 100 W/cm2 were heated with inner tube temperatures reaching approximately 800 °C, with outer temperatures exceeding or just reaching 1000 El for the multilayer and monolithic SiC tubes respectively. The tubes were then quenched with simulated rain. The tubes were then cooled and subjected to hoop stress analysis using an Instron device to assess their subsequent mechanical strength. Furthermore, the on-sun study experimental results indicate an average of 24.2% and 97% higher hoop strength for the CMC tubes than those composed of monolithic SiC and aluminum oxide (A1203) respectively.

14 SOLAR ENERGY↗

DOE OSTI2022

Towards underwater additive manufacturing via additive friction stir deposition

Given the challenges in feed material supply and quality control, metal additive manufacturing has rarely been implemented in austere environments, especially underwater. This paper explores the underwater operation potential of an emerging solid-state additive technology: additive friction stir deposition, wherein material feeding and bonding are enabled by mechanical forces with minimal influences from water. It is demonstrated that additive friction stir deposition of 304 stainless steel can be successfully performed with the print head and substrate immersed in water. High temperature is reached in the deposition zone (>60% melting temperature); the material deposition behavior is similar to that in typical open-air operation. The as-deposited material is fully-dense, having fewer annealing twins and a substantially smaller grain size than the feed material (4.98 μm vs. 31.44 μm ). Such microstructural changes stem from dynamic recrystallization caused by the large strain and high temperature introduced during deposition. In addition to grain refinement, small equiaxed dispersoids (~2–3 μm or less) are formed and evenly distributed in the austenite steel matrix. Rich in Cr, Mn, and O, these particles likely result from the reaction between the elements in stainless steel and water at elevated temperatures.

16 TIDAL AND WAVE POWER↗

DOE OSTI2025

Accelerated Fuel Qualification of Fast Modular Reactor Fuel in a Thermal Reactor: Modeling and Simulation Paired with Irradiation Testing

The accelerated fuel qualification (AFQ) methodology is applied by simulating accelerated fuel tests of the General Atomics Electromagnetic Systems’ fuel system for its 44-MW(electric) gas-cooled, fast-spectrum fast modular reactor (FMR). This fuel is comprised of UO 2 pellets in SiGA® cladding, a silicon carbide ceramic matrix composite. Fast reactors, like the FMR, offer many benefits, including high fuel utilization and flexibility, but may require a lengthy material design process if tests are performed using fast neutron irradiation alone. A thermal neutron irradiation can instead be used to rapidly test how well key components of the current material models extend to high burnup. Thermal neutrons produce a different radial power distribution within the pin than fast neutrons. However, the temperature and burnup values for the two neutron types are comparable, and the differences between the simulated fuel responses are relatively small, demonstrating the weak sensitivity of the physics-based fuel model calculations on the neutron type and the irradiation rate. Furthermore, the deformation of the SiGA cladding saturates after about 1 displacement per atom for both neutron spectra. In an accelerated fuel test, the irradiation time required to reach the target fuel burnup can be reduced by a factor of 3 by using a small rodlet with a 45% smaller pellet diameter while maintaining the same linear power. Therefore, the time for data collection up to high burnup can be significantly reduced while maintaining the same temperature profile, which largely determines the material response. Tests of fuel rodlets of standard and compact size will be carried out in the Idaho National Laboratory’s Advanced Test Reactor (ATR), including full size and compact rodlets with varying gap sizes. By applying physics-based mechanistic modeling and simulation in accordance with the AFQ methodology, this type of compact rodlet testing in a thermal test reactor captures the necessary phenomena to test fuel material models up to high burnup and to simulate the expected impact of fast neutron radiation on the fuel in FMR operations. Finally, this approach to testing fast reactor fuels in existing thermal test reactors, paired with advanced physics-based mechanistic modeling and simulation, is expected to be applicable to a range of advanced fuels and will decrease the overall fuel qualification timeframe from decades to years.

Advanced test reactor (ATR)↗

DOE OSTI2021

Robust d-Wave Superconductivity in the Square-Lattice t–J Model

Unravelling competing orders emergent in doped Mott insulators and their interplay with unconventional superconductivity is one of the major challenges in condensed matter physics. Here, to explore the possible superconducting state in a doped Mott insulator, we study the square-lattice t-J model with both the nearest-neighbor and next-nearest-neighbor electron hoppings and spin interactions. By using the state-of-the-art density matrix renormalization group calculation with imposing charge U(1) and spin SU(2) symmetries on the six-leg cylinders, we establish a quantum phase diagram including three phases: a stripe charge density wave phase, a superconducting phase without static charge order, and a superconducting phase coexistent with a weak charge stripe order. Crucially, we demonstrate that the superconducting phase has a power-law pairing correlation that decays much slower than the charge density and spin correlations, which is a quasi-1D descendant of the uniform d-wave superconductor in two dimensions. These findings reveal that enhanced charge and spin fluctuations with optimal doping is able to produce robust d-wave superconductivity in doped Mott insulators, providing a foundation for connecting theories of superconductivity to models of strongly correlated systems.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗