Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “material irradiation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

FY21 progress report for Advanced Re-fabrication/Re-instrumentation Capability Development

This report will focus on progress and development in establishment of refabrication/instrumentation capability at Idaho National Laboratory (INL). Refabrication/instrumentation is considered an enabling capability that allows access to fuel materials at any point in their life cycle. It is also critical in supporting deployment and qualification of ATF materials as many candidate materials are already undergoing irradiation as lead test rods (LTR) in commercial nuclear power plans (NPP) and irradiation in ATR alone can not produce the quantities of materials necessary to support qualification.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Behavior of helium cavities in ion-irradiated W-Ni-Fe ductile-phase toughened tungsten

This study reports on the distribution of helium (He) cavities in a hot-rolled W-Ni-Fe ductile-phase toughened tungsten (DPT W) composite irradiated to a dose and a helium concentration that are comparable to those in the material after 5-year irradiation in a conceptual fusion power plant. Here, the DPT W sample consists of W particles embedded in a ductile-phase NiFeW matrix with a nominal composition of 90W-7Ni-3Fe by weight. It was hot-rolled to a thickness reduction by 87% (87R DPT W). Sequential irradiation of the material with 1.2 MeV Ni + ions to a fluence of 2.15×10 16 Ni + /cm 2 and 90 keV He + ions to 6.5×10 15 He + /cm 2 was performed at 973 K. Larger He cavities with a lower number density are observed in NiFeW than W. Helium cavities are aggregated preferentially along the NiFeW/W interphase boundary. This behavior is not observed along the W/W grain boundary under the same irradiation conditions. A similar distribution of He cavities with comparable sizes is observed in 87R DPT W irradiated with He + ions only, suggesting that the He cavity distribution is not significantly affected by pre-irradiation of Ni + ions at 973 K. The data from this study does not provide any evidence for formation of visible voids or Ni precipitates in W phase irradiated with Ni + ions only. Diffusion and clustering of He atoms and mobile vacancies during ion irradiation at 973 K are responsible for the formation and growth of the He cavities.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Dynamic System Scaling Application to Accelerated Nuclear Fuel Testing

The development of nuclear fuel and materials requires a continuous effort to investigate the acute and prolonged effects of irradiation, thermal-material stress, chemical change, or other conceivable damage mechanics acquired during normal operation or accident scenarios throughout its lifetime. As in-core fuel property measurement techniques advance to support in the real-time, non-invasive, and enhanced accuracy realm, it is the future of fuel development to pursue to higher degrees of control, predictability of integral test behavior via separate effects test (SET), and shorter test time intervals. The fuel development life cycle from initial concept to commercial licensing is approximated to be 20 years and current literature suggests by optimizing fuel performance codes with SETs, the process could possibly be compressed to 5 to 10 years. Recently, a research group in the Idaho National Laboratory (INL) is testing reduced scale fuel rods and increased power density to accelerate evolution of fuel phenomena in metallic fuels. In support of nuclear fuel rod development, compressing fuel test process, and accelerating fuel phenomena, it was the purpose of this study to investigate nuclear fuel performance phenomena via literature review and effectively scale the initial conditions, boundary conditions, and geometric properties to describe the time-dependent response including to fuel burnup, thermal and mechanical stress, transmutations and inter-diffusion, and other relevant observed phenomena. The study was based on BISON simulations of historic EBR-II metallic fuel experiments and Dynamical System Scaling (DSS) method are utilized to assess effects of scaling activity including fuel phenomena acceleration and calculations of time-dependent distortions. The research successfully scaled metallic fuel phenomena, accelerated fuel testing, and assessed the distortions for each scaled case derived.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Impact of post-irradiation annealing on mechanical performance of irradiated 718 alloy

Here, the effect of post-irradiation annealing on solution-annealed 718 alloy was investigated using advanced mechanical testing, fractography, scanning electron microscopy, and transmission electron microscopy. Specimens were extracted from a proton beam window operated at the Spallation Neutron Source, irradiated with 940 MeV protons to a maximum dose of approximately 9.7 displacements per atom (dpa) at a calculated temperature not exceeding 110 °C while in service. Helium and hydrogen concentrations reached about 1700 and 6900 atomic parts per million (appm), respectively. Despite irradiation and high tensile strength (yield stress over 1 GPa), the material exhibited significant ductility. Annealing at 500 °C, 700 °C, and 900 °C for 30 min resulted in an appreciable decrease in yield strength and an increase in ductility for annealing treatments at 500 °C and 900 °C relative to the strength and ductility of the as-irradiated material. The presence of helium and hydrogen led to cavity formation and cleavage-like brittle features on fractured surfaces; however, high-magnification imaging revealed the presence of small-scale ductile dimples, indicating that the fracture mechanism remained mixed. The annealed specimens retained total elongation levels of 14–33 %, and there was no sudden drop in ductility after heat treatments. The ductility level in the irradiated and annealed material is notable despite the presence of helium and hydrogen.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Perspectives on Tailoring Neutron Energy Spectra in Material Test Reactors

Material test reactors (MTRs) are used to irradiate nuclear fuels and materials to develop data for how they endure neutron bombardment in or near reactor cores. Most historic MTRs, and all that remain operational in the US today, are water-cooled types and produce a thermalized neutron flux. New irradiation facilities are needed which can produce neutron energy spectra relevant to fast and fusion reactor environments. Construction of these facilities will take several years of steadfast funding to complete, which poses a formidable schedule challenge for current fast and fusion reactor developers. Irradiation designs which modify the neutron energy spectra delivered to test specimens in thermal spectrum MTRs, an approach referred to as “spectral tailoring”, can be used to approximate several relevant phenomena in the materials needed to enable fast and fusion reactor technologies. This approach is imperfect, but still valuable in the present situation. Here, the two highest flux MTRs operational in the United States, the Advanced Test Reactor (ATR) and High Flux Isotope Reactor (HFIR), have rich histories, ongoing developments, and new potentials for spectral tailoring that will be reviewed and discussed in this paper.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Progress and Challenges of Additive Manufacturing of Tungsten and Alloys as Plasma-Facing Materials

Tungsten (W) and W alloys are considered as primary candidates for plasma-facing components (PFCs) that must perform in severe environments in terms of temperature, neutron fluxes, plasma effects, and irradiation bombardment. These materials are notoriously difficult to produce using additive manufacturing (AM) methods due to issues inherent to these techniques. The progress on applying AM techniques to W-based PFC applications is reviewed and the technical issues in selected manufacturing methods are discussed in this review. Specifically, we focus on the recent development and applications of laser powder bed fusion (LPBF), electron beam melting (EBM), and direct energy deposition (DED) in W materials due to their abilities to preserve the properties of W as potential PFCs. Additionally, the existing literature on irradiation effects on W and W alloys is surveyed, with possible solutions to those issues therein addressed. Finally, the gaps in possible future research on additively manufactured W are identified and outlined.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Analysis of the Structure of Heavy Ion Irradiated LaFeO 3 Using Grazing Angle X-ray Absorption Spectroscopy

Crystalline ceramics are candidate materials for the immobilization of radionuclides, particularly transuranics (such as U, Pu, and Am), arising from the nuclear fuel cycle. Due to the α-decay of transuranics and the associated recoil of the parent nucleus, crystalline materials may eventually be rendered amorphous through changes to the crystal lattice caused by these recoil events. Previous work has shown irradiation of titanate-based ceramics to change the local cation environment significantly, particularly in the case of Ti which was shown to change from 6- to 5-fold coordination. Here, this work expands the Ti-based study to investigate the behavior in Fe-based materials, using LaFeO 3 as an example material. Irradiation was simulated by heavy ion implantation of the bulk LaFeO 3 ceramic, with the resulting amorphous layer characterized with grazing angle X-ray absorption spectroscopy (GA-XAS). Insights into the Fe speciation changes exhibited by the amorphized surface layer were provided through quantitative analysis, including pre-edge analysis, and modeling of the extended X-ray absorption fine structure (EXAFS), of the GA-XAS data.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Underlying mechanism of structural transformation between GaSb and GaAs response to intense electronic excitation

Ion irradiation of semiconductors has emerged as a promising approach for fabricating self-organized nanosystems with high atomic precision, despite often being accompanied by undesirable phenomena. Exploring the mechanisms underlying structural transformations is crucial for assessing nanostructure array types under complex irradiation environments. By quantitatively calculating the thermodynamically driven processes and analyzing the impact of intrinsic structural parameters, distinct structural transformations in response to intense electronic excitation are systematically investigated in gallium antimonide (GaSb) and gallium arsenide (GaAs) systems. In high-energy regimes, the nanofibers layer of GaSb exhibits intriguing structural discrepancy, characterized by partial nanofibers with coherent boundaries, interspersed nanopores accompanied by antisite defects and Ga precipitates, distinguishing to a series of discontinuous latent tracks that emerged within cylindrical trajectories in GaAs. Furthermore, significant diffusion behaviors of the nanohillocks are discovered in GaAs, with higher average roughness than GaSb, driven by the gradient stress distribution influenced by the free-surface effects. The deposition energy for melting phase formation, Gibbs free energy, and Ga diffusion coefficients contribute to the distinctive structural features, evidencing relatively stable morphological configurations and higher irradiation resistance in GaAs. Consequently, special optoelectronic properties associated with structural discrepancies facilitate the design and optimization of material functionalities by irradiation technologies.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effects of radiation damage and precipitate distribution on micro-pillar compression testing of irradiated CuCrZr

The results of small-scale mechanical tests are convoluted by the so-called size effect, whereby materials appear stronger when the scale of the test is reduced to the order of microns or less. The dimensional range over which this occurs has been shown to be linked to a change in sample microstructure, such as the addition of defects induced by irradiation. To investigate this response, a CuCrZr alloy was subjected to proton irradiation and mechanically tested using micro compression of pillars with a range in size. It was found that irradiation defects dominate over the extrinsic size effect and the sensitivity to differences in precipitate microstructure was also somewhat reduced, suggesting that size-independent results could be obtained from much smaller test volumes in irradiated material compared to their non-irradiated counterparts. Lastly, comparison was made between the increase in yield strength predicted by models and the experimentally measured values to establish the key parameters driving the strengthening behaviour.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Thermo-Mechanical Analysis of Irradiated MURR LEU Fuel Plates

The University of Missouri Research Reactor (MURR®) is a multi-disciplinary research and education facility providing a broad range of analytical, materials science, and irradiation services to the research community and the commercial sector. MURR is one of five U.S. high performance research reactors (USHPRR), plus one critical facility, actively collaborating with the National Nuclear Security Administration (NNSA) Material Management and Minimization (M 3 ) Reactor Conversion Program to convert from the use of highly enriched uranium (HEU, ≥ 20 wt% U 235) to low-enriched uranium (LEU, < 20 wt% U-235) fuel. All USHPRR, including MURR, completed designs with a new type of very high-density LEU fuel based on an alloy of uranium and 10-weight percent molybdenum (U-10Mo) for conversion to LEU fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Preliminary Thermo-Mechanical Analysis of Irradiated MURR LEU Fuel Element

The University of Missouri Research Reactor (MURR) is a multi-disciplinary research and education facility providing a broad range of analytical, materials science, and irradiation services to the research community and the commercial sector. MURR is one of five U.S. high performance research reactors (USHPRR), plus one critical facility, that is actively collaborating with the National Nuclear Security Administration (NNSA) Material Management and Minimization (M3) Office of Reactor Conversion and Uranium Supply to convert from the use of highly enriched uranium (HEU, ≥ 20 wt% U-235) to low-enriched uranium (LEU, < 20 wt% U-235) fuel. A new type of very high-density LEU fuel based on an alloy of uranium and 10-weight percent molybdenum (U-10Mo) is expected to allow the conversion of some USHPRR, including MURR, to LEU fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Investigation of hardening mechanisms and size effects in proton-irradiated HT-9 steels

Ferritic/martensitic steels, such as HT-9, are known for their complex microstructural features and mechanical properties. Here in this paper, in-situ micro-tensile tests and traditional fractography methods were utilized to study the fracture behavior of proton-irradiated HT-9 steels. First, to evaluate the viability of micro-tensile tests for nuclear material qualification process, meso-tensile tests on as-received HT-9 steels were performed. Fracture mechanisms of unirradiated HT-9 steels at both length scales were compared and underlying mechanisms discussed. The direct comparison of micro- and meso-scale data shows a distinctive size effect demonstrated by the increase in yield stress (YS). Upon completion of initial assessment, specimens were irradiated with 4 MeV + protons to three fluences, all of which were lower than 0.01 displacements per atom (dpa). As expected, the YS increases with irradiation. However, at 7 × 10 -3 dpa, the reversal of the trend was observed, and the YS exhibited sharp decline. We demonstrate that at lower length scales, grain structure has a more profound impact on the mechanical properties of irradiated materials, which provides information needed to fill in the gap in current understanding of the HT-9 fracture at different length scales.

36 MATERIALS SCIENCE↗
NASA NTRS1973

NERVA irradiation program. GTR 23, volume 1: Combined effects of reactor radiation and cryogenic temperature on NERVA structural materials

Specimens fabricated from structural materials that were candidates for certain NERVA applications were irradiated in liquid nitrogen (LN2), liquid hydrogen (LH2), water, and air. The specimens irradiated in LN2 were stored in LN2 and finally tested in LN2, or at some higher temperature in a few instances. The specimens irradiated in LH2 underwent an unplanned warmup while in storage so this portion of the test was lost; some specimens were tested in LN2 but none were tested in LH2. The Ground Test Reactor was the radiation source. The test specimens consisted mainly of tensile and fracture toughness specimens of several different materials, but other types of specimens such as tear, flexure, springs, and lubricant were also irradiated. Materials tested include Hastelloy X, Al, Ni steel, steel, Be, ZrC, Ti-6Al-4V, CuB, and Ti-5Al-2.5Sn.

Mcdaniel, R. H.↗
NASA NTRS2015

Fe and O EELS Studies of Ion Irradiated Murchison CM2 Carbonaceous Chondrite Matrix

Introduction: The physical and chemical response of hydrated carbonaceous chondrite materials to space weathering processes is poorly understood. Improving this understanding is a key part of establishing how regoliths on primitive carbonaceous asteroids respond to space weathering processes, knowledge that supports future sample return missions (Hayabusa 2 and OSIRISREx) that are targeting objects of this type. We previously reported on He+ irradiation of Murchison matrix and showed that the irradiation resulted in amorphization of the matrix phyllosilicates, loss of OH, and surface vesiculation. Here, we report electron energy-loss spectroscopy (EELS) measurements of the irradiated material with emphasis on the Fe and O speciation. Sample and Methods: A polished thin section of the Murchison CM2 carbonaceous chondrite was irradiated with 4 kilovolts He(+) (normal incidence) to a total dose of 1 x 10(exp 18) He(+) per square centimeter. We extracted thin sections from both irradiated and unirradiated regions in matrix using focused ion beam (FIB) techniques with electron beam deposition for the protective carbon strap to minimize surface damage artifacts from the FIB milling. The FIB sections were analyzed using a JEOL 2500SE scanning and transmission electron microscope (STEM) equipped with a Gatan Tridiem imaging filter. EELS spectra were collected from 50 nanometer diameter regions with an energy resolution of 0.7 electronvolts FWHM at the zero loss. EELS spectra were collected at low electron doses to minimize possible artifacts from electron-beam irradiation damage. Results and Discussion: Fe L (sub 2,3) EELS spectra from matrix phyllosilicates in CM chondrites show mixed Fe(2+)/Fe(3+) oxidation states with Fe(3+)/Sigma Fe approximately 0.5. Fe L(sub 2,3) spectra from the irradiated/ amorphized matrix phyllosilicates show higher Fe(2+)/Fe(3+) ratios compared to spectra obtained from pristine material at depths beyond the implantation/amorphization layer. We also obtained O Ka spectra from phyllosilicates in both regions of the sample. The O Ka spectra show a pre-edge feature at approximately 530.5 electronvolts that is related to O 2p states hybridized with Fe 3d states. The intensity ratio of the O Ka pre-edge peak relative to the main part of the O Ka edge (that results from transitions of O 1s to 2p states) is lower in the irradiated layer compared to the pristine material and may reflect the loss of O (as OH) as was observed by IR spectroscopy. Conclusions: In addition to amorphization and OH loss, EELS spectra of He(+) irradiated matrix phyllosilicates in Murchison show that some of the Fe(3+) is reduced to Fe(2+). Spectral deconvolution is underway to extract quantitative ratios from the EELS spectra.

Keller, L. P.↗
DOE OSTI2021

Revealing nano-scale lattice distortions in implanted material with 3D Bragg ptychography

Small ion-irradiation-induced defects can dramatically alter material properties and speed up degradation. Unfortunately, most of the defects irradiation creates are below the visibility limit of state-of-the-art microscopy. As such, our understanding of their impact is largely based on simulations with major unknowns. Here we present an x-ray crystalline microscopy approach, able to image with high sensitivity, nano-scale 3D resolution and extended field of view, the lattice strains and tilts in crystalline materials. Using this enhanced Bragg ptychography tool, we study the damage helium-ion-irradiation produces in tungsten, revealing a series of crystalline details in the 3D sample. Our results lead to the conclusions that few-atom-large ‘invisible’ defects are likely isotropic in orientation and homogeneously distributed. A partially defect-denuded region is observed close to a grain boundary. These findings open up exciting perspectives for the modelling of irradiation damage and the detailed analysis of crystalline properties in complex materials.

42 ENGINEERING↗
DOE OSTI2021

Strengthening of tungsten by coherent rhenium precipitates formed during low fluence irradiation

Experimental data show that the accumulation of rhenium and osmium from transmutation reactions severely affect the microstructural evolution and property degradation of tungsten-based materials under neutron irradiation. Theory and modeling have confirmed that Re atom transport in W is by irradiation-produced migrating self-interstitial atoms. With this diffusion mode in operation, a specific microstructure evolution is realized when at relatively low neutron fluence the Re-rich precipitates are formed, while the void and interstitial loop population development is suppressed, affecting the mechanical properties. Here, this research shows the effect of small coherent Re-rich precipitates on the dislocation glide under stress, investigated using the molecular dynamics approach with empirical interatomic potentials. The results are compared with an earlier simulation of void hardening in W. It is demonstrated that small coherent Re-rich precipitates of less than 6 nm diameter represent relatively weak obstacles for moving edge dislocations. The implication of these results on the interpretation of experimental results is discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Stacked target irradiations and radiochemical separations for simultaneous production of short-lived Ni and Ir isotopes

A method was developed for simultaneous production of neutron-deficient Ni and Ir isotopes by irradiation of stacked targets with a 50.5 MeV proton beam, followed by radiochemical separations to remove excess target material. The target, irradiation configuration, and post-irradiation radiochemical separations were developed and tested in a proof-of-principle irradiation. Radiochemical yields and purity of the products are discussed. Finally, the stacked target method, developed herein, can be used to produce other isotope pairs with appropriate beam tailoring.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
NASA NTRS2003

Characterization of Candidate Solar Sail Material Exposed to Space Environmental Effects

Solar sailing is a unique form of propulsion where a spacecraft gains momentum from incident photons. Solar sails are not limited by reaction mass and provide continual acceleration, reduced only by the lifetime of the lightweight film in the space environment and the distance to the Sun. Once thought to be difficult or impossible, solar sailing has come out of science fiction and into the realm of possibility. Any spacecraft using this method would need to deploy a thin sail that could be as large as many kilometers in extent. The availability of strong, ultra lightweight, and radiation resistant materials will determine the future of solar sailing. The National Aeronautics and Space Administration's Marshall Space Flight Center (MSFC) is concentrating research into the utilization of ultra lightweight materials for spacecraft propulsion. The Space Environmental Effects Team at MSFC is actively characterizing candidate solar sail material to evaluate the thermo-optical and mechanical properties after exposure to space environmental effects. This paper will describe the exposure of candidate solar sail materials to emulated space environmental effects including energetic electrons, combined electrons and Ultraviolet radiation, and hypervelocity impact of irradiated solar sail material. This paper will describe the testing procedure and the material characterization results of this investigation.

Edwards, David↗