SEARCH · Engineering Papers

Results for “machining”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

All sources NASA NTRS DOE OSTI

NASA NTRS2003

New Technique of High-Performance Torque Control Developed for Induction Machines

Two forms of high-performance torque control for motor drives have been described in the literature: field orientation control and direct torque control. Field orientation control has been the method of choice for previous NASA electromechanical actuator research efforts with induction motors. Direct torque control has the potential to offer some advantages over field orientation, including ease of implementation and faster response. However, the most common form of direct torque control is not suitable for the highspeed, low-stator-flux linkage induction machines designed for electromechanical actuators with the presently available sample rates of digital control systems (higher sample rates are required). In addition, this form of direct torque control is not suitable for the addition of a high-frequency carrier signal necessary for the "self-sensing" (sensorless) position estimation technique. This technique enables low- and zero-speed position sensorless operation of the machine. Sensorless operation is desirable to reduce the number of necessary feedback signals and transducers, thus improving the reliability and reducing the mass and volume of the system. This research was directed at developing an alternative form of direct torque control known as a "deadbeat," or inverse model, solution. This form uses pulse-width modulation of the voltage applied to the machine, thus reducing the necessary sample and switching frequency for the high-speed NASA motor. In addition, the structure of the deadbeat form allows the addition of the high-frequency carrier signal so that low- and zero-speed sensorless operation is possible. The new deadbeat solution is based on using the stator and rotor flux as state variables. This choice of state variables leads to a simple graphical representation of the solution as the intersection of a constant torque line with a constant stator flux circle. Previous solutions have been expressed only in complex mathematical terms without a method to clearly visualize the solution. The graphical technique allows a more insightful understanding of the operation of the machine under various conditions.

Kenny, Barbara H.↗

NASA NTRS2009

Computerized Machine for Cutting Space Shuttle Thermal Tiles

A report presents the concept of a machine aboard the space shuttle that would cut oversized thermal-tile blanks to precise sizes and shapes needed to replace tiles that were damaged or lost during ascent to orbit. The machine would include a computer-controlled jigsaw enclosed in a clear acrylic shell that would prevent escape of cutting debris. A vacuum motor would collect the debris into a reservoir and would hold a tile blank securely in place. A database stored in the computer would contain the unique shape and dimensions of every tile. Once a broken or missing tile was identified, its identification number would be entered into the computer, wherein the cutting pattern associated with that number would be retrieved from the database. A tile blank would be locked into a crib in the machine, the shell would be closed (proximity sensors would prevent activation of the machine while the shell was open), and a "cut" command would be sent from the computer. A blade would be moved around the crib like a plotter, cutting the tile to the required size and shape. Once the tile was cut, an astronaut would take a space walk for installation.

Ramirez, Luis E.↗

NASA NTRS2016

Machine Learning Technologies and Their Applications for Science and Engineering Domains Workshop -- Summary Report

The fields of machine learning and big data analytics have made significant advances in recent years, which has created an environment where cross-fertilization of methods and collaborations can achieve previously unattainable outcomes. The Comprehensive Digital Transformation (CDT) Machine Learning and Big Data Analytics team planned a workshop at NASA Langley in August 2016 to unite leading experts the field of machine learning and NASA scientists and engineers. The primary goal for this workshop was to assess the state-of-the-art in this field, introduce these leading experts to the aerospace and science subject matter experts, and develop opportunities for collaboration. The workshop was held over a three day-period with lectures from 15 leading experts followed by significant interactive discussions. This report provides an overview of the 15 invited lectures and a summary of the key discussion topics that arose during both formal and informal discussion sections. Four key workshop themes were identified after the closure of the workshop and are also highlighted in the report. Furthermore, several workshop attendees provided their feedback on how they are already utilizing machine learning algorithms to advance their research, new methods they learned about during the workshop, and collaboration opportunities they identified during the workshop.

Ambur, Manjula↗

NASA NTRS2019

Application of Machine Learning Techniques to Delay Tolerant Network Routing

This dissertation discusses several machine learning techniques to improve routing in delay tolerant networks (DTNs). These are networks in which there may be long one-way trip times, asymmetric links, high error rates, and deterministic as well as non-deterministic loss of contact between network nodes, such as interplanetary satellite networks, mobile ad hoc networks and wireless sensor networks. This work uses historical network statistics to train a multi-label classifier to predict reliable paths through the network. In addition, a clustering technique is used to predict future mobile node locations. Both of these techniques are used to reduce the consumption of resources such as network bandwidth, memory and data storage that is required by replication routing methods often used in opportunistic DTN environments. Thesis contributions include: an emulation tool chain developed to create a DTN test bed for machine learning, the network and software architecture for a machine learning based routing method, the development and implementation of classification and clustering techniques and performance evaluation in terms of machine learning and routing metrics.

Dudukovich, Rachel M.↗

NASA NTRS2019

Machine Learning-Based Atmospheric Phenomena Detection Platform

As the number of Earth pointing satellites has increased over the last several decades, the data volume retrieved from instruments onboard these satellites has also increased. It is expected that this trend will continue as more data intensive missions and small satellite constellations are launched. Currently, feature detection - namely atmospheric phenomena - in these datasets is performed manually and is thus not scalable with the growing data archives. Recent advancements in computational efficiency allow for the Earth science community to leverage machine learning to identify interesting atmospheric phenomena. Given the wide range of distinctive features in various atmospheric phenomena, a specialized machine learning model is required for accurate detection of these phenomena independently. The Phenomena Portal, developed at NASA IMPACT, is designed to provide visualization for the output from these machine learning models. In addition, detected events for each atmospheric phenomena are stored in a database that can be used to more easily use/subset larger spatiotemporal datasets. The user interface also incorporates additional features to enhance the user experience including spatiotemporal analysis, multiple base layer images, and a slider to filter events with lower probabilities of positive detection. Each detection supports user feedback on whether the detection is true or false that can then be stored and used to improve the machine learning model performance.

Gurung, Iksha↗

NASA NTRSDate not supplied

QuantifyML: How good is my machine learning model?

This paper presents an approach, QuantifyML, which employs model counting to assess the learnability and robustness of machine learning models. Typically the efficacy of machine learning models is determined by computing their accuracy statistically on test data sets. However, this may be misleading, if the test data is not representative of the problem that is being studied. Further, two different models may have the same accuracy on a given data set, measured statistically, but may be very different in their behavior on unseen data. Also, models with high accuracy could have poor adversarial robustness. In QuantifyML, our goal is to precisely quantify the extent to which machine learning models have learned and generalized from the given data. In QuantifyML, a trained model is translated into a C program, which is fed to the CBMC model checking tool to produce a formula in Conjunctive Normal Form (CNF), which in turn is analyzed with state-of-the-art model counters to efficiently obtain precise counts w.r.t different outputs. QuantifyML enables i) evaluating the learnability of models by comparing the counts for the outputs to ground truth, expressed as logical predicates (if available), ii) comparing the performance of different models that may be built with different machine learning algorithms (e.g., decision-trees vs. neural networks), and iii) quantifying the robustness of trained models around given inputs. Our evaluation demonstrates these applications of QuantifyML on decision trees and neural networks trained to learn relational properties of graphs, for which we know the ground truth, and to perform image classification, for which we do not have the ground truth, but we can quantify local robustness.

Deep Neural Networks↗

NASA NTRSDate not supplied

QuantifyML: How Good is My Machine Learning Model?

We present QuantifyML, which applies model counting to assess the learn ability, safety, and robustness of machine learning models. Typically, the efficacy of machine learning models is determined by computing their accuracy statistically on test datasets. However, this may be misleading, if the test data is not representative of the problem that is being studied. With QuantifyML we aim to precisely quantify the extent to which machine learning models have learned and generalized from the given data. In QuantifyML, a trained model is translated into aC program, which is fed to the CBMC model checking tool to produce a formula in Conjunctive Normal Form (CNF), which in turn is analyzed with state-of-the-art model counters to efficiently obtain precise countsw.r.t different outputs. QuantifyML enables i) evaluating the learnability of models by comparing the counts for the outputs to ground truth, ex-pressed as logical predicates (if available), ii) comparing the performance of different models that may be built with different machine learning algorithms (e.g., decision-trees vs. neural networks), and iii) quantifying the safety and robustness of trained models.

Deep Neural Networks↗

NASA NTRSDate not supplied

Potential of Materials to Impact Megawatt-Scale Electric Machines

High specific power density, megawatt-scale electric machines (motors and generators) are needed to enable megawatt-scale electric aircraft propulsion systems for single isle aircraft. Thermally insulating electrical insulation materials in the stator windings limits the ability to thermally manage the heat produced in these machines. Polymer-ceramic composites along with novel processing techniques offer viable options to improve the thermal conductivity of the electrical insulation system. This paper outlines current National Aeronautics and Space Administration’s Glenn Research Center efforts of developing several polymer-ceramic systems and processing techniques as they relate to electric machine insulation (including potting). There is also analysis of how these factors relate to machine performance.

electric macnhine↗

NASA NTRS2023

Influences of Varied Electrical Discharge Machining Operations on Surface Conditions of Several Nickel-Based Superalloys

Nickel-based superalloys designed for use in gas turbine engines blades are difficult and expensive to properly machine without undue surface damage, due in part to their superior mechanical properties at high temperatures. Numerically controlled electrical discharge machining (EDM) has progressed to commonly be used as a machining process for initial sectioning, detailed roughing, and even some finishing operations. The objective of this study was to examine the effect of EDM on resulting surface conditions of superalloy 718 after slicing using typical rough, semi-finish, and finish condition sets with a typical wire EDM machine. Surface roughness, residual stress, and microstructures were compared for these conditions. The varied EDM conditions influenced surface roughness as intended. The residual stresses and surface roughness directly corresponding to the EDM steps were determined. While roughness decreased when progressing from rough to finish EDM conditions, tensile residual stresses unexpectedly increased. Brief assessments after EDM of two higher performance powder metallurgy disk superalloys ME209 and LSHR indicated this inverse relationship of roughness versus tensile residual stress was also present for these superalloys, where tensile residual stresses were significantly enhanced.

superalloys↗

NASA NTRSDate not supplied

Improvements of the Load Schedule for the Machine Calibration of a Strain-Gage Balance

The load schedule for the calibration of a six-component force balance in a calibration machine was improved. Now, single-component loads are repeated in regular intervals during the calibration. This approach has several advantages. First, the number of single-component loads increases to about twenty-two percent of all loads and load combinations. Consequently, more accurate numerical estimates of the primary bridge sensitivities can be obtained if global regression is used for the analysis of the calibration data. In addition, single-component repeats make it possible to track the stability of the applied loads during the calibration process. Finally, interactions of single-component repeats can be compared with interactions that are observed during the application of manual loads to the balance. Machine calibration and manual data sets of two force balances are used to illustrate benefits of the new load schedule. It is shown in the examples how differences between the observed interactions of machine calibration and manual data can be quantified. The suggested improvements can also be implemented in the load schedule for the machine calibration of a moment or direct-read balance as long as single-component loads are included that are described in the design load format of the balance.

wind tunnel test↗

NASA NTRSDate not supplied

Concept Design of a 5 MW Axial Flux Partially Superconducting Electric Machine

Single aisle class and larger electric and hybrid electric airplanes require high performance electric machines with power levels greater than 1 MW. Partially superconducting machines with superconducting rotors cooled by cryocoolers and no-cryogenic stators are one possible solution for meeting the machine performance requirements at these power levels. In this paper, a conceptual design for a double-stator single-rotor axial-flux partially superconducting machine is presented. A design tool for the topology is presented and used to generate an initial concept design. High fidelity analysis of the concept design is used to access the feasibility of the concept design to meet its target performance metrics and find areas of refinement for the next iteration of the design tool and the design.

Thomas Tallerico↗

DOE OSTI2020

Performance Prediction of Big Data Transfer Through Experimental Analysis and Machine Learning

Big data transfer in next-generation scientific applications is now commonly carried out over connections with guaranteed bandwidth provisioned in High-performance Networks (HPNs) through advance bandwidth reservation. To use HPN resources efficiently, provisioning agents need to carefully schedule data transfer requests and allocate appropriate bandwidths. Such reserved bandwidths, if not fully utilized by the requesting user, could be simply wasted or cause extra overhead and complexity in management due to exclusive access. This calls for the capability of performance prediction to reserve bandwidth resources that match actual needs. Towards this goal, we employ machine learning algorithms to predict big data transfer performance based on extensive performance measurements, which are collected over a span of several years from a large number of data transfer tests using different protocols and toolkits between various end sites on several real-life physical or emulated HPN testbeds. We first identify a comprehensive list of attributes involved in a typical big data transfer process, including end host system configurations, network connection properties, and control parameters of data transfer methods. We then conduct an in-depth exploratory analysis of their impacts on application-level throughput, which provides insights into big data transfer performance and motivates the use of machine learning. We also investigate the applicability of machine learning algorithms and derive their general performance bounds for performance prediction of big data transfer in HPNs. Experimental results show that, with appropriate data preprocessing, the proposed machine learning-based approach achieves 95% or higher prediction accuracy in up to 90% of the cases with very noisy real-life performance measurements.

Yun, Daqing↗

DOE OSTI2020

Scroll-type machine

A scroll-type displacement machine, e.g. scroll compressor, has fixed and orbiting scrolls and an Oldham ring to prevent relative rotation between scrolls. A drive module positioned between the orbiting scroll and drive shaft incorporates an eccentric drive system and first and second counterweights for dynamic balancing. The motor, motor bearings, and motor shaft (i.e., drive shaft) are packaged as a separate, modular unit (e.g. “off-the-shelf” motor) that attaches to the compressor frame. The machine is configured as a high-side machine with a low-pressure port at a radial outer portion of the fixed scroll and a high-pressure port or discharge port located in the floor of the orbiting scroll at its axis, with high pressure flow passing over and around the eccentric drive bearing and drive mechanism. The Oldham ring is distributed on a lateral or radial plane of the scroll pair with a portion surrounding a portion of the fixed scroll and another portion surrounding a portion of the orbiting scroll. The ring may be formed as four arcuate members arranged on two levels, to occupy otherwise unused space in the scroll-type machine.

42 ENGINEERING↗

DOE OSTI2022

A Boundary Topology Optimization Approach for Lightweighting Electric Machines Inspired by Additive Manufacturing

Minimizing the mass in electric machines while maintaining superior performance has become a new requirement for the advancement of drivetrains used in wind energy and electric mobility. Topology optimization for light-weighting electric machines using traditional approaches typically explore a restricted design space allowed by standard parametrizable geometry and manufacturing, while advanced methods like cell-based density approaches suffer from a lack of robust manufacturability constraints during the optimization process. To overcome these drawbacks, we explore a grid-independent, boundary TO where the outer shape of the magnet is parameterized using Bezier curves. We conduct a design of experiments (DOE) to study the effect of different magnet shapes on machine performance by varying the control points on the Bezier curves. A machine-learning based surrogate model is constructed using the data from the DOE to quantify the relationship between the control points, air-gap torque and mass. The control points are then optimized to maximize the torque density. The approach is used for minimizing electrical steel mass in the IEA-15MW radial flux direct-drive wind turbine generator. The free-from boundary TO resulted in smooth and concise shapes that can be easily additively manufactured with upto 20-ton reduction in electrical steel mass.

additive manufacturing↗

DOE OSTI2022

A New Shape Optimization Approach for Lightweighting Electric Machines Inspired by Additive Manufacturing: Preprint

Minimizing the mass in electric machines while maintaining superior performance is a new requirement for the advancement of drivetrains used in wind energy and electric mobility. Topology optimization (TO) for lightweighting electric machines using traditional approaches typically explores a restricted design space allowed by standard parametrizable geometry and manufacturing, while advanced methods, such as cell-based density approaches, suffer from a lack of robust manufacturability constraints during the optimization process. To overcome these drawbacks, we explore a grid-independent, boundary TO where the outer shape of the magnet is parameterized using Bezier curves. We conduct a design of experiments (DOE) to study the effect of different magnet shapes on machine performance by varying the control points on the Bezier curves. A machine-learning-based surrogate model is constructed using the data from the DOE to quantify the relationship between the control points, air-gap torque, and mass. The control points are then optimized to maximize the torque density. The approach is used for minimizing electrical steel mass in the International Energy Agency (IEA) 15-MW radial flux direct-drive wind turbine generator. The free-form boundary TO resulted in smooth and concise shapes that can be easily additively manufactured with up to a 20-ton reduction in electrical steel mass.

additive manufacturing↗

DOE OSTI2022

Generative memory for lifelong machine learning

Techniques are disclosed for training machine learning systems. An input device receives training data comprising pairs of training inputs and training labels. A generative memory assigns training inputs to each archetype task of a plurality of archetype tasks, each archetype task representative of a cluster of related tasks within a task space and assigns a skill to each archetype task. The generative memory generates, from each archetype task, auxiliary data comprising pairs of auxiliary inputs and auxiliary labels. A machine learning system trains a machine learning model to apply a skill assigned to an archetype task to training and auxiliary inputs assigned to the archetype task to obtain output labels corresponding to the training and auxiliary labels associated with the training and auxiliary inputs assigned to the archetype task to enable scalable learning to obtain labels for new tasks for which the machine learning model has not previously been trained.

Nadamuni Raghavan, Aswin↗

DOE OSTI2023

Cutting force estimation from machine learning and physics-inspired data-driven models utilizing accelerometer measurements

Monitoring cutting forces for process control may be challenging because force measurements typically require invasive instrumentation. To remedy this situation, two new methods were recently developed to estimate cutting forces in real time based on the use of on-machine accelerometer measurements. One method uses machine learning, while another uses a physics-inspired data-driven approach, to generate a model that estimates cutting forces from on-machine accelerations. The estimated forces from both approaches were compared against cutting force data collected during various milling operations on several machine tools. The results reveal the advantages and disadvantages of each model to estimate real-time cutting forces.

Vogl, Greg↗

DOE OSTI2023

Integrated electro-hydraulic machine

An integrated electromechanical and hydraulic system is disclosed which includes an electric machine, the electric machine includes a casing, a stator adapted to remain stationary within the casing, one or more electrically insulated windings coupled to the stator, a rotor separated from the stator and the one or more windings by a radial diamagnetic gap, electrical power couplings, and a first mechanical power couplings, and a hydraulic machine also disposed in the housing, the hydraulic machine having hydro-mechanical couplings as well as a second mechanical power couplings, wherein the second mechanical power couplings are coupled to the first mechanical power couplings.

Vacca, Andrea↗