Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “low temperatures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Low temperature atomic layer deposition of PbO 2 for electrochemical applications

A low temperature atomic layer deposition (ALD) process for PbO 2 was developed using bis(1-dimethylamino-2-methyl-2-propanolate)lead(II), Pb(DMAMP) 2 , and O 3 as the reactants, with a high growth rate of 2.6 Å/cycle. PbO 2 readily reduces under low oxygen partial pressures at moderate temperatures making it challenging to deposit ALD PbO 2 from Pb 2+ precursors. However, thin films deposited with this process showed small crystalline grains of α-PbO 2 and β-PbO 2 , without signs of reduced PbO x phases. The ALD PbO 2 thin films show the high electrical conductivity characteristic of bulk PbO 2 . In situ measurements of ALD PbO 2 film conductivity during growth suggest a reaction mechanism by which sub-surface oxygen mobility contributes to the growth of resistive PbO or PbO x during the Pb(DMAMP) 2 surface reaction step, which is only fully oxidized from Pb 2+ to Pb 4+ during the O 3 reaction step. These films were electrochemically reduced to PbSO 4 in H 2 SO 4 and then reoxidized to PbO 2 , demonstrating their suitability for use as an electrode material for fundamental battery research and other electrochemical applications.

atomic layer deposition↗
NASA NTRS2003

Synthesis and Characterization of Chalcopyrite (CuInS2 and CuhInSe2) Colloidal Nanoparticles for Optoelectronic Applications via Low-Temperature Pyrolysis of Single-Source Precursors

Nanocrystalline (or quantum dot) materials hold potential as components of next-generation photovoltaic (PV) devices. The inclusion of quantum dots in PV devices has been proposed as a means to improve the efficiency of photon conversion (quantum dot solar cell), enable low-cost deposition of thin-films, provide sites for exciton dissociation, and pathways for electron transport. Quantum dots are also expected to be more resistant to degradation from electron, proton, and alpha particle radiation than the corresponding bulk material, a requirement for use in space solar ~sells. Chalcopyrite nanocrystals can be produced by low-temperature thermal decomposition of single-source precursors such as (PR3)2CuIn(ER')4 (R = Ph, R' = Et, E = S; R = R' = Ph, E = Se). Single-source precursors are molecules which contain all the necessary elements for synthesis of a desired material. Thermal decomposition of the precursor results in the formation of material with the correct stoichiometry as a nanocrystalline powder or a thin film, often at significantly lower temperatures than those typically employed for thin-film deposition by multi-source evaporation techniques, typically less than 500 C. We show that CuInSz and CuInSe2 nanocrystals can be synthesized from the precursors at temperatures as low as 250 C. The nanocrystals are characterized by optical spectroscopy, X-ray diffraction, and electron microscopy.

Castro, S. L.↗
NASA NTRS2000

Modeling X-Ray Photoionized Plasmas: Ion Storage Ring Measurements of Low Temperature Dielectronic Recombination Rate Coefficients for L-Shell Iron

Iron L-shell ions (Fe XVII to Fe XXIV) play an important role in determining the line emission and thermal and ionization structures of photoionized gases. Existing uncertainties in the theoretical low temperature dielectronic recombination (DR) rate coefficients for these ions significantly affects our ability to model and interpret observations of photoionized plasmas. To help address this issue, we have initiated a laboratory program to produce reliable low temperature DR rates. Here, we present some of our recent results and discuss some of their astrophysical implications.

Savin, D. W.↗
NASA NTRS2001

Low Temperature Growth of Nanostructured Diamond Films on Metals

The field of nanocrystalline diamond and tetrahedral amorphous carbon films has been the focus of intense experimental activity in the last few years for applications in field emission display devices, optical windows, and tribological coatings, The choice of substrate used in most studies has typically been silicon. For metals, however, the thermal expansion mismatch between the diamond film and substrate gives rise to thermal stress that often results in delamination of the film. To avoid this problem in conventional CVD deposition low substrate temperatures (less than 700 C) have been used, often with the incorporation of oxygen or carbon monoxide to the feedgas mixture. Conventionally grown CVD diamond films are also rough and would require post-deposition polishing for most applications. Therefore, there is an obvious need to develop techniques for deposition of well-adhered, smooth nano-structured diamond films on metals for various tribological applications. In our work, nanostructured diamond films are grown on a titanium alloy substrate using a two-step deposition process. The first step is performed at elevated temperature (820 C) for 30 minutes using a H2/CH4/N2 gas mixture in order to grow a thin (approx. 600 nm) nanostructured diamond layer and improve film adhesion. The remainder of the deposition involves growth at low temperature (less than 600 C) in a H2/CH4/O2 gas mixture. Laser reflectance Interferometry (LRI) pattern during growth of a nanostructured diamond film on Ti-6Al-4V alloy. The first 30 minutes are at a high temperature of 820 C and the rest of the film is grown at a low temperature of 580 T. The fringe pattern is observed till the very end due to extremely low surface roughness of 40 nm. The continuation of the smooth nanostructured diamond film growth during low temperature deposition is confirmed by in-situ laser reflectance interferometry and by post-deposition micro-Raman spectroscopy and surface profilometry. Similar experiments performed without the starting nanostructured diamond layer resulted in poorly adhered films with a more crystalline appearance and a higher surface roughness. This low temperature deposition of nanostructured diamond films on metals offers advantages in cases where high residual thermal stress leads to delamination at high temperatures.

Baker, Paul A.↗
NASA NTRS2015

Evaluation of Low Temperature CO Removal Catalysts

CO removal from spacecraft gas streams was evaluated for three commercial, low temperature oxidation catalysts: Carulite 300, Sofnocat 423, and Hamilton Sundstrand Pt1. The catalysts were challenged with CO concentrations (1-100 ppm) under dry and wet (50% humidity) conditions using 2-3 % O2. CO removal and CO2 concentration were measured at constant feed composition using a FTIR. Water vapor affected the CO conversion of each catalyst differently. An initial screening found that Caulite 300 could not operate in humid conditions. The presence of water vapor affected CO conversion of Sofnocat 423 for challenge concentrations below 40 ppm. The conversion of CO by Sofnocat 423 was 80% at CO concentrations greater than 40 ppm under both dry and moist conditions. The HS Pt1 catalyst exhibited CO conversion levels of 100% under both dry and moist conditions.

Low Temperature↗
DOE OSTI2021

A molecular beam and computational study on the barrierless gas phase formation of (iso)quinoline in low temperature extraterrestrial environments

Despite remarkable progress toward the understanding of the formation pathways leading to polycyclic aromatic hydrocarbons (PAHs) in combustion systems and in deep space, the complex reaction pathways leading to nitrogen-substituted PAHs (NPAHs) at low temperatures of molecular clouds and hydrocarbon-rich, nitrogen-containing atmospheres of planets and their moons like Titan have remained largely obscure. Here, we demonstrate through laboratory experiments and computations that the simplest prototype of NPAHs – quinoline and isoquinoline (C 9 H 7 N) – can be synthesized via rapid and de-facto barrier-less reactions involving o-, m- and p-pyridinyl radicals (C 5 H 4 N˙) with vinylacetylene (C 4 H 4 ) under low-temperature conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1993

Low temperature synthesis of monolithic transparent Ta2O5 gels from hydrolysis of metal alkoxide

Tantalum oxide gels in the form of transparent monoliths and powder were prepared from hydrolysis of tantalum pentaethoxide under controlled conditions using different mole ratios of Ta(OC2H5)5:C2H50H:H20:HCl. Alcohol acts as the mutual solvent and HCl as the deflocculating agent. For a fixed alkoxide:water:HCl ratio, time of gel formation increased with the alcohol to alkoxide mole ratio. Thermal evolution of the physical and structural changes in the gel was monitored by differential thermal analysis, thermogravimetric analysis, x-ray diffraction, and infrared spectroscopy. On heating to approximately 400 C, the amorphous gel crystallized into the low temperature orthorhombic phase Beta-Ta2O5, which transformed into the high temperature tetragonal phase Alpha-Ta2O5 when further heated to approximately 1450 C. The volume fraction of the crystalline phase increased with the firing temperature. The Alpha-Ta205 converted back into the low temperature phase, Beta-Ta2O5, on slow cooling through the transformation temperature of 1360 C indicating a slow but reversible transformation.

Bansal, Narottam P.↗
DOE OSTI2022

Low-temperature processed beta-phase In 2 Se 3 ferroelectric semiconductor thin film transistors

As scaling becomes increasingly difficult, there is growing interest in vertical or three-dimensional stacking of transistors and especially memory. Ferroelectric semiconductor field effect transistors can be key enablers to improve energy efficiency and overall chip and memory performance. In this work, low-temperature processed, back-end-of-the-line compatible transistors were demonstrated by depositing a layered chalcogenide ferroelectric semiconductor, beta-phase In 2 Se 3 , at temperature as low as 400 °C. Top gate n-channel In 2 Se 3 thin film transistors were fabricated with field-effect mobility ∼1 cm 2 V −1 s −1 , and simple polarization switching based memory results are presented.

36 MATERIALS SCIENCE↗
NASA NTRS1993

Lifetimes of bacteriochlorophyll fluorescence in Rhodopseudomonas viridis and Heliobacterium chlorum at low temperatures

Fluorescence lifetimes of isolated membranes of Rhodopseudomonas viridis were measured in the temperature range of 77 K to 25 K. At room temperature, the main component of the fluorescence decay of bacteriochlorophyll (BChl) b had a time constant of 50 ps. In contrast to other purple bacteria, the emission at low temperature was spectrally homogeneous and showed essentially single lifetimes of 140 ps at 77 K and 180 ps at 25 K, with the primary electron donor in the oxidized state. Taking into account the relative fluorescence yields with open and closed reaction centers, we arrive at numbers of 125 ps and 215 ps, respectively, for open reaction centers. These numbers are significantly smaller than expected on the basis of measurements of the efficiency of charge separation, perhaps suggesting that the excitation decay in the absence of reaction centers is considerably faster at low temperature than at room temperature. At least four different spectral components with different lifetimes were observed at 25 K in the emission of Heliobacterium chlorum, a short-wavelength component of about 30 ps and three longer-wavelength components of about 100 ps, 300 ps, and 900 ps. This indicates a strong heterogeneity in the emitting pigment, BChl g-808. The component with the shortest lifetime does not appear to be affected by the redox state of the reaction center and might reflect energy transfer to BChl g species which are connected to the reaction center.

NASA Discipline Number 52-30↗
NASA NTRSDate not supplied

Indigenous Organic Matter Associated with Unusual Low Temperature Aqueous Secondary Phases in the Mars Meteorite Nakhla

In freshly fractured chips of the Mars meteorite Nakhla, we found carbonaceous phases intimately associated with secondary aqueous alteration phases, both mineral and amorphous, interpreted to have formed through the low-temperature, mineral-water dissolution of the host Martian basalt.We have characterized the nature of carbonaceous matter and spatially associated secondary phases within Nakhla using a multidisciplinary suite of optical and electron beam instrumentation(Thomas-Keprta et al., 2022). Secondary Phases: The preserved secondary mineral phases are best described as ‘juvenile’ hydrated amorphous silica formed when water interacts with mafic rocks. Although amorphous silica on Earth rarely persists through geologic time due to alteration into other phases, e.g.,microcrystalline opal-CT and eventually quartz, the lack of maturation of primarily amorphous silica with embedded nano phase ferrihydrite in Nakhla infers these phases formed in a limited water environment by low temperature, circumneutral pH fluids stabilized by the presence of coexisting amorphous silica.Additionally, we report the presence of the ferrous hydroxycarbonate mineral chukanovite (Fe2(OH)2CO3)within some of the secondary mineral aggregates studied. Organic Matter:Indigenous Nakhla carbonaceous matter is present both in condensed phases and in a dispersed state spatially associated with secondary alteration phases. In the former, discrete refractory micron to submicron assemblages were identified that appear macromolecular in nature and, in several cases, associated with F and, in one case, significant N. While organically bound Fhas yet to be detected remotely on Mars, the identification of organic N within one of the carbonaceous phases is considered a prerequisite for Martian astrobiological potential. Summary: Neither the intimate association of carbonaceous matter with secondary phases nor the identification of chukanovite have been previously reported in any of the Martian meteorites.A variety of habitability-related metastable solid-phase, oxidation-reduction, and organic-molecular sample attributes in Nakhla formed hundreds of millions of years ago near Mars’ surface; these alteration products persisted on Mars until very recentlyand resemble the amorphous materials observed at Gale crater by Mars Science Laboratory CuriosityRover (Rampe et al., 2020).Similar phases may be expected to occur elsewhere on Mars (e.g., Jezerocrater). References: Rampe E. B. et al.(2020) Mineralogy and geochemistry of sedimentary rocks and eolian sediments in Gale crater, Mars: A review after six Earth years of exploration with Curiosity.Geochemistry80, 125605; Thomas-Keprta K.L. et al. (2022) Indigenous carbon-rich matter associated with unusual aqueous alteration features in Nakhla: Complex formation and preservation history. Geochim. et Cosmochim. Acta320, 41-78 (online).

Mars meteorite↗
NASA NTRS2016

Low Temperature Regolith Bricks for In-Situ Structural Material

Current technology for producing in-situ structural materials on future missions to Mars or the moon relies heavily on energy-intensive sintering processes to produce solid bricks from regolith. This process requires heating the material up to temperatures in excess of 1000 C and results in solid regolith pieces with compressive strengths in the range of 14000 to 28000 psi, but are heavily dependent on the porosity of the final material and are brittle. This method is currently preferred over a low temperature cementation process to prevent consumption of precious water and other non-renewable materials. A high strength structural material with low energy requirements is still needed for future colonization of other planets. To fulfill these requirements, a nano-functionalization process has been developed to produce structural bricks from regolith simulant and shows promising mechanical strength results. Functionalization of granular silicate particles into alkoxides using a simple low temperature chemical process produces a high surface area zeolite particles that are held together via inter-particle oxygen bonding. Addition of water in the resulting zeolite particles produces a sol-gel reaction called "inorganic polymerization" which gives a strong solid material after a curing process at 60 C. The aqueous solution by-product of the reaction is currently being investigated for its reusability; an essential component of any ISRU technology. For this study, two batches of regolith bricks are synthesized from JSC-1A; the first batch from fresh solvents and chemicals, the second batch made from the water solution by-product of the first batch. This is done to determine the feasibility of recycling necessary components of the synthesis process, mainly water. Characterization including BET surface area, SEM, and EDS has been done on the regolith bricks as well as the constituent particles,. The specific surface area of 17.53 sq m/g (average) of the granular regolith material was obtained from nitrogen adsorption isotherm measurement. The size, shape and textures of regolith from SEM shows that the particles are 25-50 micrometers in size and mostly irregular in shape (Figure 1a). The elemental composition of regolith was identified from EDS analysis showed the presence of Si, Al, Fe, Na, Mg, Ca, Ti, O and C (see figure 1b). Each set of cylindrical brick samples were prepared by low energy process, and cured for 21 and 28 days, respectively to compare their compressive strength. Figure 1c, and d shows the JSC-1A brick and the compressive strength measurements. The results from the 21 day cured bricks (2 bricks) have been done and yielded an aver-age strength of 3050 psi, considerably higher than Portland cement mortars (Type IV and V). This promising technology provides the benefits of construction material similar to concrete, with a low complexity, low energy synthesis process and the likelihood of complete reusability of precious resources. Compressive strength using this method can be improved by increasing the surface area of the particles, using bi-modal particle size distribution, and adding certain additives to increase inter-particle forces.

ISRU↗
NASA NTRS1989

Low temperature storage container for transporting perishables to space station

Two storage containers are disclosed within which food or biological samples may be stored for transfer in a module by the space shuttle to a space station while maintaining the food or samples at very low temperatures. The container is formed in two parts, each part having an inner shell and an outer shell disposed about the inner shell. The space between the shells is filled with a continuous wrap multi-layer insulation and a getter material. The two parts of the container have interlocking members and when connected together are sealed for preventing leakage from the space between the shells. After the two parts are filled with frozen food or samples they are connected together and a vacuum is drawn in the space between the shells and the container is stored in the module. For the extremely low temperature requirements of biological samples, an internal liner having a phase change material charged by a refrigerant coil is disposed in the space between the shells, and the container is formed from glass fiber material including honeycomb structural elements. All surfaces of the glass fiber which face the vacuum space are lined with a metal foil.

Owen, James W.↗
NASA NTRS2014

Low Temperature Double-Layer Capacitors Using Asymmetric and Spiro-Type Quaternary Ammonium Salts

Double-layer capacitors capable of operating at extremely low temperatures (e.g., as low as -80.degree. C.) are disclosed. Electrolyte solutions combining a base solvent (e.g., acetonitrile) and a cosolvent are employed to lower the melting point of the base electrolyte. Example cosolvents include methyl formate, ethyl acetate, methyl acetate, propionitrile, butyronitrile, and 1,3-dioxolane. A quaternary ammonium salt including at least one of triethylmethylammonium tetrafluoroborate (TEMATFB) and spiro-(1,1')-bipyrrolidium tetrafluoroborate (SBPBF.sub.4), is used in an optimized concentration (e.g., 0.10 M to 0.75 M), dissolved into the electrolyte solution. Conventional device form factors and structural elements (e.g., porous carbon electrodes and a polyethylene separator) may be employed.

Brandon, Erik J.↗