Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “graphite anodes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

461 records · Page 26
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Ultrastructures and Mechanics of Annealed Nephila clavipes Major Ampullate Silk

The semicrystalline protein structure and impressive mechanical properties of major ampullate (MA) spider silk make it a promising natural alternative to polyacrylonitrile (PAN) fibers for carbon fiber manufacture. However, when annealed using a similar procedure to carbon fiber production, the tensile strength and Young’s modulus of MA silk decrease. Despite this, MA silk fibers annealed at 600 °C remain stronger and tougher than similarly annealed PAN but have a lower Young’s modulus. Although MA silk and PAN graphitize to similar extents, annealing disrupts the hydrogen bonding that controls crystal alignment within MA silk. Consequently, unaligned graphite crystals form in annealed MA silk, causing it to weaken, while graphite crystals in PAN maintain alignment along the fiber axis, strengthening the fibers. Finally, these shortcomings of spider silk when annealed provide insights into the selection and design of future alternative carbon fiber precursors.

36 MATERIALS SCIENCE↗
NASA NTRS1985

Long-life high performance fuel cell program

A multihundred kilowatt Regenerative Fuel Cell for use in a space station is envisioned. Three 0.508 sq ft (471.9 cm) active area multicell stacks were assembled and endurance tested. The long term performance stability of the platinum on carbon catalyst configuration suitability of the lightweight graphite electrolyte reservoir plate, the stability of the free standing butyl bonded potassium titanate matrix structure, and the long life potential of a hybrid polysulfone cell edge frame construction were demonstrated. A 18,000 hour demonstration test of multicell stack to a continuous cyclical load profile was conducted. A total of 12,000 cycles was completed, confirming the ability of the alkaline fuel cell to operate to a load profile simulating Regenerative Fuel Cell operation. An orbiter production hydrogen recirculation pump employed in support of the cyclical load profile test completed 13,000 hours of maintenance free operation. Laboratory endurance tests demonstrated the suitability of the butyl bonded potassium matrix, perforated nickel foil electrode substrates, and carbon ribbed substrate anode for use in the alkaline fuel cell. Corrosion testing of materials at 250 F (121.1 C) in 42% wgt. potassium identified ceria, zirconia, strontium titanate, strontium zirconate and lithium cobaltate as candidate matrix materials.

Martin, R. E.↗
DOE OSTI2021

Effect of Temperature and FEC on Silicon Anode Heat Generation Measured by Isothermal Microcalorimetry

Isothermal microcalorimetry (IMC) was used to better understand parasitic reactions and heat generation from Si electrodes in the first 10 cycles using Li/Si half cells. Heat generation from cell polarization (ohmic heat), entropy changes (reversible heat), and parasitic reactions (parasitic heat) are separated and quantified. The effect of temperature and fluoroethylene carbonate (FEC) as an electrolyte additive are also explored. Our results show that at the C/10 cycling rate used here, ohmic heat makes the largest contribution to overall heat generation while reversible heat is the smallest. Ohmic heat generation increases with cycle number due to increasing internal resistance, though the effect is smaller for cells with FEC. Interestingly, capacity-normalized parasitic heat generation is largely unaffected by changes in temperature despite differing reaction kinetics. We show that this is caused by a decrease in average parasitic reaction enthalpy as temperature is increased. Further, cells with FEC display higher average parasitic reaction enthalpy than cells without. The average parasitic reaction enthalpies for all the Si electrodes we tested were lower than previously reported values for graphite, indicating that the SEI formed on Si is less stable.

25 ENERGY STORAGE↗
DOE OSTI2025

Electrochemical stability and corrosion behavior of Ni-Cr alloy in molten LiCl-KCl salt

This study investigated the electrochemical properties and potential-dependent stability of Cr(II) and Ni(II) in a eutectic LiCl-KCl molten salt at 500 °C under an argon atmosphere using a three-electrode cell configuration with a glassy carbon working electrode, Ag/Ag + reference electrode, and graphite counter electrode. Cyclic voltammetry was employed to characterize the Cr(0)/Cr(II)/Cr(III) and Ni(0)/Ni(II) redox transitions, yielding diffusion coefficients of 0.50 (±0.01) × 10 −5 cm 2 s −1 for Cr(II) and 0.91 (±0.16) × 10 −5 cm 2 s −1 for Ni(II) at 500 °C. The redox stability domains of these species provided insight into the corrosion mechanisms of a Ni-Cr alloy (80–20 wt %) in LiCl-KCl salt. The measured open circuit potential of the alloy corresponded to the range of potentials where the Ni(0) and Cr(II) species are stable, indicating a preferential dissolution of Cr. Immersion testing of the alloy for 336 h confirmed significant Cr depletion (or Ni-enrichment) at the surface layer, corroborating Cr dealloying as the dominant corrosion reaction under open circuit conditions. Additionally, the application of a small anodic overpotential (0.11 V) resulted in selective Cr dissolution while a large anodic overpotential (0.25 V) resulted in co-dissolution of both Cr and Ni. Furthermore, these results demonstrate that the corrosion mechanisms of a Ni-Cr alloy in LiCl-KCl depend upon the applied potential, and thus the redox conditions of the molten salt should be carefully controlled in the design of a redox buffer to mitigate corrosion in molten salt environments.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Formation of Carbon–Carbon Interlinkage Bonds under High Pressure

The formation of carbon–carbon interlinkage bonds (CCIBs) via the chemical binding of interlayer carbon atoms of many sp 2 -bonded carbon precursors is an essential step for synthesizing various diamond and diamond-like materials. Although the existence of CCIBs may be reasonably assumed under high-pressure conditions, direct experimental evidence has been scarce. Micro-Raman spectroscopy is here employed to track in situ the evolution of C–C bonds in a pressure range from ambient to 54 GPa. A pressure-induced two-stage (polynomial and linear) shift of the G peak and new generation of the CCIB peak at about 1550 cm –1 are observed in multiple types of layer-structured carbon precursors, including glassy carbon, natural graphite, and carbon nanotubes. In conclusion, the experimental discovery of CCIBs holds significance in comprehending phase transitions of sp 2 -bonded carbon materials and has implications for the advancement of novel carbon structures.

Anode materials↗
DOE OSTI2022

Understanding the Solution Dynamics and Binding of a PVDF Binder with Silicon, Graphite, and NMC Materials and the Influence on Cycling Performance

The impact of the binding, solution structure, and solution dynamics of poly(vinylidene fluoride) (PVDF) with silicon on its performance as compared to traditional graphite and Li 1.05 Ni 0.33 Mn 0.33 Co 0.33 O 2 (NMC) electrode materials was explored. Through refractive index (RI) measurements, the concentration of the binder adsorbed on the surface of electrode materials during electrode processing was determined to be less than half of the potentially available material resulting in excessive free binder in solution. Using ultrasmall-angle neutron scattering (USANS) and small-angle neutron scattering (SANS), it was found that PVDF forms a conformal coating over the entirety of the silicon particle. This is in direct contrast to graphite–PVDF and NMC–PVDF slurries, where PVDF only covers part of the graphite surface, and the PVDF chains make a network-like graphite–PVDF structure. Conversely, a thick layer of PVDF covers NMC particles, but the coating is porous, allowing for ion and electronic transport. The homogeneous coating of silicon breaks up percolation pathways, resulting in poor cycling performance of silicon materials as widely reported. These results indicate that the Si–PVDF interactions could be modified from a binder to a dispersant.

25 ENERGY STORAGE↗
DOE OSTI2024

Strain-Induced Shifts in Defective Graphite Phonon Modes Predicted by Density Functional Theory

Carbon fiber composites have gained attention as a structural material because of their high strength-to-weight ratio, and understanding the effect of defects on reactivity and mechanical properties is important for the longevity and safety of the composite. Although it is known that strain causes the underlying graphitic vibrational modes to redshift, it is not clear how strain may alter reactivity and defect-induced vibrational changes. To investigate the strain-induced phonon changes of defective carbon fiber composites, density functional theory calculations of graphite are used, including intercalated hydrogen and fluorine defects. By comparing changes in the bond lengths, formation energies, and phonon density of states for uniaxially and biaxially strained graphite, strain was found to generally make defect formation more favorable and the specific behavior changes are dependent on the strain direction and defect identity. Specifically, intercalated fluorine phonons are more sensitive to strain than hydrogen intercalation phonons, and strain applied along the zigzag direction alters the calculated properties more than strain along the armchair direction. Finally, these results highlight the importance of understanding the microstructural effect of deviations from the ideal material because small changes in strain or defect type can significantly alter the behavior of the carbon fiber composite core.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2005

NSTAR Extended Life Test Discharge Chamber Flake Analysis

The Extended Life Test (ELT) of the NASA Solar Electric Propulsion Technology Readiness (NSTAR) ion thruster was concluded after 30,352 hours of operation. The ELT was conducted using the Deep Space 1 (DS1) back-up flight engine, a 30 cm diameter xenon ion thruster. Post-test inspection of the ELT engine revealed numerous contaminant flakes distributed over the bottom of the cylindrical section of the anode within the discharge chamber (DC). Extensive analyses were conducted to determine the source of the particles, which is critical to the understanding of degradation mechanisms of long life ion thruster operation. Analyses included: optical microscopy (OM) and particle length histograms, field emission scanning electron microscopy (FESEM) combined with energy dispersive spectroscopy (EDS), and atomic oxygen plasma exposure tests. Analyses of the particles indicate that the majority of the DC flakes consist of a layered structure, typically with either two or three layers. The flakes comprising two layers were typically found to have a molybdenum-rich (Mo-rich) layer on one side and a carbon-rich (C-rich) layer on the other side. The flakes comprising three layers were found to be sandwich-like structures with Mo-rich exterior layers and a C-rich interior layer. The presence of the C-rich layers indicates that these particles were produced by sputter deposition build-up on a surface external to the discharge chamber from ion sputter erosion of the graphite target in the test chamber. This contaminant layer became thick enough that particles spalled off, and then were electro-statically attracted into the ion thruster interior, where they were coated with Mo from internal sputter erosion of the screen grid and cathode components. Atomic oxygen tests provided evidence that the DC chamber flakes are composed of a significant fraction of carbon. Particle size histograms further indicated that the source of the particles was spalling of carbon flakes from downstream surfaces. Analyses of flakes taken from the downstream surface of the accelerator grid provided additional supportive information. The production of the downstream carbon flakes, and hence the potential problems associated with the flake particles in the ELT ion thruster engine is a facility induced effect and would not occur in the space environment.

deGroh, Kim K.↗
DOE OSTI2025

Microstructure Scale Lithium-Ion Battery Modeling: Part I. On Through-Plane Heterogeneity, Impact of Mesh Representation, and Differences between Macro- and Microscale Models

Li-ion battery performance and degradation are strongly correlated with the electrode microstructures and can be modeled at different scales, each with their own limitations. Herein, we compare predictions achieved with a macro- and a micro-scale model, that is, respectively, neglecting or considering the microstructural heterogeneity of the composite electrodes, on virtual numerically generated and real microstructures. While both models are in relative agreement at the low charge rates, differences arise for fast charging scenarios and especially for the real, highly heterogenous, microstructures. The microscale model predicts that electrolyte concentration saturation and depletion, respectively, at the back of the cathode and of the anode are exacerbated, and that lithium plating occurs earlier for real microstructures. The present work also indicates that the mesh representation significantly impacts the microscale model predictions, and consequently that microscale models should add surface area as a parameter to consider explicitly surface roughness. This article is the first of a series, with subsequent entries further investigating in-plane heterogeneities, lithium plating, and the impact of microstructure representativity on model predictions.

25 ENERGY STORAGE↗
NASA NTRS2004

Lithium Polymer Electrolytes and Solid State NMR

Research is being done at the Glenn Research Center (GRC) developing new kinds of batteries that do not depend on a solution. Currently, batteries use liquid electrolytes containing lithium. Problems with the liquid electrolyte are (1) solvents used can leak out of the battery, so larger, more restrictive, packages have to be made, inhibiting the diversity of application and decreasing the power density; (2) the liquid is incompatible with the lithium metal anode, so alternative, less efficient, anodes are required. The Materials Department at GRC has been working to synthesize polymer electrolytes that can replace the liquid electrolytes. The advantages are that polymer electrolytes do not have the potential to leak so they can be used for a variety of tasks, small or large, including in the space rover or in space suits. The polymers generated by Dr. Mary Ann Meador's group are in the form of rod -coil structures. The rod aspect gives the polymer structural integrity, while the coil makes it flexible. Lithium ions are used in these polymers because of their high mobility. The coils have repeating units of oxygen which stabilize the positive lithium by donating electron density. This aids in the movement of the lithium within the polymer, which contributes to higher conductivity. In addition to conductivity testing, these polymers are characterized using DSC, TGA, FTIR, and solid state NMR. Solid state NMR is used in classifying materials that are not soluble in solvents, such as polymers. The NMR spins the sample at a magic angle (54.7') allowing the significant peaks to emerge. Although solid state NMR is a helpful technique in determining bonding, the process of preparing the sample and tuning it properly are intricate jobs that require patience; especially since each run takes about six hours. The NMR allows for the advancement of polymer synthesis by showing if the expected results were achieved. Using the NMR, in addition to looking at polymers, allows for participation on a variety of other projects, including aero-gels and carbon graphite mat en als. The goals of the polymer electrolyte research are to improve the physical properties of the polymers. This includes improving conductivity, durability, and expanding the temperature range over which it is effective. Currently, good conductivity is only present at high temperatures. My goals are to experiment with different arrangements of rods and coils to achieve these desirable properties. Some of my experiments include changing the number of repeat units in the polymer, the size of the diamines, and the types of coil. Analysis of these new polymers indicates improvement in some properties, such as lower glass transition temperature; however, they are not as flexible as desired. With further research we hope to produce polymers that encompass all of these properties to a high degree.

Berkeley, Emily R.↗
DOE OSTI2025

Intrinsic Layer-Dependent Surface Energy and Exfoliation Energy of van der Waals Materials

Stacking and twisting 2D van der Waals (vdW) layers have become versatile platforms to tune the electron correlation. These platforms rely on exfoliating vdW materials down to a single vdW layer and a few vdW layers. We calculate the intrinsic layer-dependent surface and exfoliation energies of typical vdW materials such as graphite, h-BN, black P, MX 2 (M = Mo or W; X = S, Se, or Te), MX (M = Ga or In; X = S, Se, or Te), Bi 2 Te 3 , and MnBi 2 Te 4 using density functional theory. For exchange-correlation functionals with explicit vdW interaction, a single vdW layer always has the smallest surface energy, giving a surface energy reduction when compared to that of thicker vdW layers. Furthermore, the magnitude of this surface energy reduction quickly decreases with an increase in the number of atomic layers inside the single vdW layer for different vdW materials. Such atomic-layer dependence in surface energy reduction helps explain the different effectiveness of exfoliation for different vdW materials down to a single vdW layer.

Anode materials↗