Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “gas composition”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

Investigation of Magnetite Oxidation Kinetics at the Particle Scale

The induration of magnetite pellets is a complex physico-chemical process that involves oxidation, sintering, and heat transfer. The thermal- and gas-composition profile that is experienced by the pellet in an induration reactor could result in the formation of a homogenous or heterogeneous pellet structure, which could affect the pellet quality. The oxidation kinetics of magnetite pellets from sintering studies have been studied at two levels, namely, the pellet scale and at the particle scale, and the findings of the latter are presented here. The rate of oxidation of the magnetite concentrate depends primarily on temperature, oxygen content in the oxidizing gas, and particle size. These factors are investigated in this study. It was found that the oxidation of the magnetite concentrate is comprised of two distinct stages, a primary stage with high rates followed by a secondary stage where rates decrease significantly. The isothermal oxidation behavior as analyzed by the Avrami kinetic model was found to fit better than the shrinking-core model. The partially oxidized particles were examined microstructurally to supplement the experimental and model results. The Avrami kinetic model for isothermal oxidation was extended to non-isothermal profiles using the superposition principle, and the model was validated experimentally.

36 MATERIALS SCIENCE↗

Process Considerations for the Production of Hydrogen via Steam Reforming of Oxygenated Gases from Biomass Pyrolysis and Other Conversion Processes

Abstract In 2021, average CO 2 emissions was 9.7 g CO 2 /g H 2 produced, primarily based on steam methane reforming (SMR) technology that currently dominates hydrogen production. The substitution of natural gas (NG) and other fossil feedstocks in SMRs with renewable gases may be considered as an option for reducing greenhouse gas emissions. This analysis explores process impacts and constraints associated with the potential introduction of biogenic gases into SMRs. The results indicate that replacing NG in the fuel train of the SMR, followed by partial replacement of NG in the feed train may be a feasible approach. For the CO‐ and CO 2 ‐rich gas compositions assumed in this analysis the results indicate that feed train may accommodate up to 25 mole % of biogenic gases using allowances in existing designs and/or with small modifications, while maintaining similar hydrogen output. NG substitution in higher proportions require more major changes because of increased flow rates and heat exchange requirements in the system. Biogenic gases with lower CO 2 and higher calorific values are advantageous for NG substitution, and dry reforming using the CO 2 present in the feed gas can reduce steam consumption and increase process efficiency within limits where coking does not become a new constraint.

08 HYDROGEN↗

Improved Recovery Boiler Performance Through Control of Combustion, Sulfur, and Alkali Chemistry

This project involved the following objectives: 1. Determine black liquor drying and devolatilization elemental and total mass release rates and yields. 2. Develop a public domain physical/chemical kinetic model of black liquor drop combustion, including new information on drying and devolatilization. 3. Determine mechanisms and rates of sulfur scavenging in recover boilers. 4. Develop non-ideal, public-domain thermochemistry models for alkali salts appropriate for recovery boilers 5. Develop data and a one-dimensional model of a char bed in a recovery boiler. 6. Implement all of the above in comprehensive combustion code and validate effects on boiler performance. 7. Perform gasification modeling in support of INEL and commercial customers. The major accomplishments of this project corresponding to these objectives are as follows: 1. Original data for black liquor and biomass data demonstrate dependencies of particle reactions on particle size, liquor type, gas temperature, and gas composition. A comprehensive particle submodel and corresponding data developed during this project predicts particle drying (including both free and chemisorbed moisture), devolatilization, heterogeneous char oxidation, char-smelt reactions, and smelt oxidation. Data and model predictions agree, without adjustment of parameters, within their respective errors. The work performed under these tasks substantially exceeded the original objectives. 2. A separate model for sulfur scavenging and fume formation in a recovery boiler demonstrated strong dependence on both in-boiler mixing and chemistry. In particular, accurate fume particle size predictions, as determined from both laboratory and field measurements, depend on gas mixing effects in the boilers that lead to substantial particle agglomeration. Sulfur scavenging was quantitatively predicted while particle size required one empirical mixing factor to match data. 3. Condensed-phase thermochemistry algorithms were developed for salt mixtures and compared with sodium-based binary and higher order systems. Predictions and measurements were demonstrated for both salt systems and for some more complex silicate-bearing systems, substantially exceeding the original scope of this work. 4. A multi-dimensional model of char bed reactivity developed under this project demonstrated that essentially all reactions in char beds occur on or near the surface, with the internal portions of the bed being essentially inert. The model predicted composition, temperature, and velocity profiles in the bed and showed that air jet penetration is limited to the immediate vicinity of the char bed, with minimal impact on most of the bed. The modeling efforts substantially exceeded the original scope of this project. 5. Near the completion of this project, DOE withdrew the BYU portion of a multiparty agreement to complete this and additional work with no advanced warning, which compromised the integration of all of this material into a commercial computer code. However, substantial computer simulations of much of this work were initiated, but not completed. 6. The gasification modeling is nearly completed but was aborted near its completion according to a DOE redirection of funds. This affected both this and the previous tasks.

01 COAL, LIGNITE, AND PEAT↗

Low power DC arcjet operation with hydrogen/nitrogen/ammonia mixtures

The effect of gas composition and ambient pressure on arcjet operation was determined. Arcjet operation in different facilities was also compared to determine the validity of tests in small facilities. Volt-ampere characteristics were determined for an arcjet using hydrogen/nitrogen mixtures (simulating both ammonia and hydrazine), hydrogen/nitrogen/ammonia mixtures, and pure ammonia as propellants at various flow rates. The arcjet had a typical performance of 450 sec specific impulse at 1 kW with hydrogen/nitrogen mixures. It was determined that the amount of ammonia present in the gas stream had a significant effect on the arcjet volt-ampere characteristics. Also, hydrogen/nitrogen mixtures simulating ammonia gave arc characteristics approximately the same as those of pure ammonia. Finally, no differences in arc volt-ampere characteristics were seen between low and high ambient pressure operation in the same facility. A 3 to 5 V difference was seen when different facilities were compared, but this difference was probably due to differences in the voltage drops across the current connections, and not due to arcjet operational differences in the two facilities.

Hardy, Terry L.↗

Low power dc arcjet operation with hydrogen/nitrogen/ammonia mixtures

The effect of gas composition and ambient pressure on arcjet operation was determined. Arcjet operation in different facilities was also compared to determine the validity of tests in small facilities. Volt-ampere characteristics were determined for an arcjet using hydrogen/nitrogen mixtures (simulating both ammonia and hydrazine), hydrogen/nitrogen/ammonia mixtures, and pure ammonia as propellants at various flow rates. The arcjet had a typical performance of 450 sec specific impulse at 1 kW with hydrogen/nitrogen mixtures. It was determined that the amount of ammonia present in the gas stream had a significant effect on the arcjet volt-ampere characteristics. Also, hydrogen/nitrogen mixtures simulating ammonia gave arc characteristics approximately the same as those of pure ammonia. Finally, no differences in arc volt-ampere characteristics were seen between low and high ambient pressure operation in the same facility. A 3 to 5 V difference was seen when different facilities were compared, but this difference was probably due to differences in the voltage drops across the current connections, and not due to arcjet operational differences in the two facilities.

Hardy, Terry L.↗

Plasma-produced phase-pure cuprous oxide nanowires for methane gas sensing

Phase-selective synthesis of copper oxide nanowires is warranted by several applications, yet it remains challenging because of the narrow windows of the suitable temperature and precursor gas composition in thermal processes. Here, we report on the room-temperature synthesis of small-diameter, large-area, uniform, and phase-pure Cu{sub 2}O nanowires by exposing copper films to a custom-designed low-pressure, thermally non-equilibrium, high-density (typically, the electron number density is in the range of 10{sup 11}–10{sup 13} cm{sup −3}) inductively coupled plasmas. The mechanism of the plasma-enabled phase selectivity is proposed. The gas sensors based on the synthesized Cu{sub 2}O nanowires feature fast response and recovery for the low-temperature (∼140 °C) detection of methane gas in comparison with polycrystalline Cu{sub 2}O thin film-based gas sensors. Specifically, at a methane concentration of 4%, the response and the recovery times of the Cu{sub 2}O nanowire-based gas sensors are 125 and 147 s, respectively. The Cu{sub 2}O nanowire-based gas sensors have a potential for applications in the environmental monitoring, chemical industry, mining industry, and several other emerging areas.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Volatile solubities in magmas - Transport of volatiles from mantles to planet surfaces

The solubility of CO2, CO, CH4, H2, and H2O in melts of NaAlSi3O8 composition was measured at the mantle conditions of pressure (10-20 Kb) and temperature (1200 C). The melt volatiles were found to have dramatically lower H2/H2O and higher CO/CO2 ratios than the fluid, due to large variations in relative solubilities of volatile species in the melt. Partial melting of source regions of either high or low oxygen fugacity (fO2) will result in magmas with intermediate fO2. This means that volcanic gases can be either more, or less reducing than their source regions and that a volcanic gas composition cannot be used to directly estimate either the fO2 or the volatile composition of the source region. The results suggest that volcanic gases will usually lie in the 'neutral' range, with the fO2 values near those of the quartz-fayalite-magnetite buffer. These gases are predominately H2O with minor CO2, CO, CH4, and H2. These conclusions should apply to earth, Mars, and Venus mantles, in which the magmas produced by partial melting have moderate silica contents, but will probably not apply to very low silica magmas, such as kimberlites, because of the very high solubility of CO2 in those magmas.

Holloway, J. R.↗

Nyx

Nyx is a highly parallel, adaptive mesh, finite-volume N-body compressible hydrodynamics solver for cosmological simulations. Nyx code solves equations of compressible hydrodynamics on an adaptive grid hierarchy coupled with an N-body treatment of dark matter. The gas dynamics in Nyx uses a finite volume methodology on a set of 3-D Eulerian grids; dark matter is represented as discrete particles moving under the influence of gravity. Particles are evolved via a particle-mesh method, using Cloud-in-Cell deposition/interpolation scheme. Both baryonic and dark matter contribute to the gravitational field. In addition, Nyx includes physics needed to accurately model the intergalactic medium: in optically thin limit and assuming ionization equilibrium, the code calculates heating and cooling processes of the primordial-composition gas in an ionizing ultraviolet background radiation field. Additional physics capabilities are under development.

Sexton, Jean [Lawrence Berkeley National Lab. (LBN↗

Analysis of Halogen-Mercury Reactions in Flue Gas

Oxidized mercury species may be formed in combustion systems through gas-phase reactions between elemental mercury and halogens, such as chorine or bromine. This study examines how bromine species affect mercury oxidation in the gas phase and examines the effects of mixtures of bromine and chlorine on extents of oxidation. Experiments were conducted in a bench-scale, laminar flow, methane-fired (300 W), quartz-lined reactor in which gas composition (HCl, HBr, NO{sub x}, SO{sub 2}) and temperature profile were varied. In the experiments, the post-combustion gases were quenched from flame temperatures to about 350 C, and then speciated mercury was measured using a wet conditioning system and continuous emissions monitor (CEM). Supporting kinetic calculations were performed and compared with measured levels of oxidation. A significant portion of this report is devoted to sample conditioning as part of the mercury analysis system. In combustion systems with significant amounts of Br{sub 2} in the flue gas, the impinger solutions used to speciate mercury may be biased and care must be taken in interpreting mercury oxidation results. The stannous chloride solution used in the CEM conditioning system to convert all mercury to total mercury did not provide complete conversion of oxidized mercury to elemental, when bromine was added to the combustion system, resulting in a low bias for the total mercury measurement. The use of a hydroxylamine hydrochloride and sodium hydroxide solution instead of stannous chloride showed a significant improvement in the measurement of total mercury. Bromine was shown to be much more effective in the post-flame, homogeneous oxidation of mercury than chlorine, on an equivalent molar basis. Addition of NO to the flame (up to 400 ppmv) had no impact on mercury oxidation by chlorine or bromine. Addition of SO{sub 2} had no effect on mercury oxidation by chlorine at SO{sub 2} concentrations below about 400 ppmv; some increase in mercury oxidation was observed at SO{sub 2} concentrations of 400 ppmv and higher. In contrast, SO{sub 2} concentrations as low as 50 ppmv significantly reduced mercury oxidation by bromine, this reduction could be due to both gas and liquid phase interactions between SO{sub 2} and oxidized mercury species. The simultaneous presence of chlorine and bromine in the flue gas resulted in a slight increase in mercury oxidation above that obtained with bromine alone, the extent of the observed increase is proportional to the chlorine concentration. The results of this study can be used to understand the relative importance of gas-phase mercury oxidation by bromine and chlorine in combustion systems. Two temperature profiles were tested: a low quench (210 K/s) and a high quench (440 K/s). For chlorine the effects of quench rate were slight and hard to characterize with confidence. Oxidation with bromine proved sensitive to quench rate with significantly more oxidation at the lower rate. The data generated in this program are the first homogeneous laboratory-scale data on bromine-induced oxidation of mercury in a combustion system. Five Hg-Cl and three Hg-Br mechanisms, some published and others under development, were evaluated and compared to the new data. The Hg-halogen mechanisms were combined with submechanisms from Reaction Engineering International for NO{sub x}, SO{sub x}, and hydrocarbons. The homogeneous kinetics under-predicted the levels of mercury oxidation observed in full-scale systems. This shortcoming can be corrected by including heterogeneous kinetics in the model calculations.

54 ENVIRONMENTAL SCIENCES↗

STS-46 plasma composition measurements using the EOIM-3 mass spectrometer

One of the active instruments incorporated into the Evaluation of Oxygen Interactions with Materials - 3 experiment was a quadrupole mass spectrometer. The primary objectives for this instrument, which was built by the Air Force Phillips Laboratory and was a veteran of the STS-4 flight in 1982, were to quantify the flux of atomic oxygen striking the test surfaces in the EOIM-3 payload and to detect surface reaction products from the materials in the carousel. Other speakers in this session have covered the results of these experiments. Prior to the 40-hour-long dedicated EOIM-3 mission segment at the end of the STS-46 flight, the authors used the mass spectrometer to make measurements of ion and neutral gas composition in the shuttle environment. About 25 hours of data were collected during a variety of mission events, including Eureca deployment at high altitude and many tethered satellite system operations.

Hunton, Donald E.↗

Momentum source signatures in thermospheric neutral composition

Perturbations in the structure of the neutral atmosphere were measured in narrow latitude bands near the dayside polar cusp by mass spectrometers aboard the S3-1 and Esro 4 satellites. The disturbances are characterized by an in-phase variation of both the lighter and the heavier species. They are observed to occur in latitude bands of about 5-10 deg extent in the altitude region of 200 km during periods of increased geomagnetic activity. It is suggested that thermospheric winds driven by momentum sources associated with ion convection are the predominant cause for these disturbances. The narrow structure features associated with the momentum source are superimposed on the thermospheric changes caused by Joule heating. Both effects may be present simultaneously, resulting in a complex response pattern of the neutral gas composition in the thermosphere.

Trinks, H.↗

Biomass Torrefaction Process Review and Moving Bed Torrefaction System Model Development

Torrefaction is currently developing as an important preprocessing step to improve the quality of biomass in terms of physical properties, and proximate and ultimate composition. Torrefaction is a slow heating of biomass in an inert or reduced environment to a maximum temperature of 300°C. Torrefaction can also be defined as a group of products resulting from the partially controlled and isothermal pyrolysis of biomass occurring in a temperature range of 200–230ºC and 270–280ºC. Thus, the process can also be called a mild pyrolysis as it occurs at the lower temperature range of the pyrolysis process. At the end of the torrefaction process, a solid uniform product with lower moisture content and higher energy content than raw biomass is produced. Most of the smoke-producing compounds and other volatiles are removed during torrefaction, producing a final product that will have a lower mass but a higher heating value. An important aspect of research is to establish a degree of torrefaction where gains in heating value offset the loss of mass. There is a lack of literature on torrefaction reactor designs and a design sheet for estimating the dimensions of the torrefier based on capacity. This study includes a) conducting a detailed review on the torrefaction of biomass in terms of understanding the process, product properties, off-gas compositions, and methods used, and b) to design a moving bed torrefier, taking into account the basic fundamental heat and mass transfer calculations. Specific objectives include calculating the dimensions like diameter and height of the moving packed bed for different capacities, designing the heat loads and gas flow rates, and developing an interactive excel sheet where the user can define design specifications. In this report, 25–1000 kg/hr are used in equations for the design of the torrefier, examples of calculations, and specifications for the torrefier.

09 BIOMASS FUELS↗

Biomass Torrefaction Process Review and Moving Bed Torrefaction System Model Development

Torrefaction is currently developing as an important preprocessing step to improve the quality of biomass in terms of physical properties, and proximate and ultimate composition. Torrefaction is a slow heating of biomass in an inert or reduced environment to a maximum temperature of 300°C. Torrefaction can also be defined as a group of products resulting from the partially controlled and isothermal pyrolysis of biomass occurring in a temperature range of 200-230°C and 270-280°C. Thus, the process can also be called a mild pyrolysis as it occurs at the lower temperature range of the pyrolysis process. At the end of the torrefaction process, a solid uniform product with lower moisture content and higher energy content than raw biomass is produced. Most of the smoke-producing compounds and other volatiles are removed during torrefaction, producing a final product that will have a lower mass but a higher heating value. An important aspect of research is to establish a degree of torrefaction where gains in heating value offset the loss of mass. There is a lack of literature on torrefaction reactor designs and a design sheet for estimating the dimensions of the torrefier based on capacity. This study includes (a) conducting a detailed review on the torrefaction of biomass in terms of understanding the process, product properties, off-gas compositions, and methods used, and (b) to design a moving bed torrefier, taking into account the basic fundamental heat and mass transfer calculations. Specific objectives include calculating the dimensions like diameter and height of the moving packed bed for different capacities, designing the heat loads and gas flow rates, and developing an interactive excel sheet where the user can define design specifications. In this report, 25-1000 kg/hr are used in equations for the design of the torrefier, examples of calculations, and specifications for the torrefier.

09 BIOMASS FUELS↗

SPOUTED BED DESIGN CONSIDERATIONS FOR COATED NUCLEAR FUEL PARTICLES

High Temperature Gas Cooled Reactors (HTGRs) are fueled with tristructural isotropic (TRISO) coated nuclear fuel particles embedded in a carbon-graphite fuel body. TRISO coatings consist of four layers of pyrolytic carbon and silicon carbide that are deposited on uranium ceramic fuel kernels (350µm – 500µm diameters) in a concatenated series of batch depositions. Each layer has dedicated functions such that the finished fuel particle has its own integral containment to minimize and control the release of fission products into the fuel body and reactor core. The TRISO coatings are the primary containment structure in the HTGR reactor and must have very high uniformity and integrity. To ensure high quality TRISO coatings, the four layers are deposited by chemical vapor deposition (CVD) using high purity precursors and are applied in a concatenated succession of batch operations before the finished product is unloaded from the coating furnace. These depositions take place at temperatures ranging from 1230°C to 1550°C and use three different gas compositions, while the fuel particle diameters double, their density drops from 11.1 g/cm3 to 3.0 g/cm3, and the bed volume increases more than 8-fold. All this is accomplished without the aid of sight ports or internal instrumentation that could cause chemical contamination within the layers or mechanical damage to thin layers in the early stages of each layer deposition. The converging section of the furnace retort was specifically designed to prevent bed stagnation that would lead to unacceptably high defect fractions and facilitate bed circulation to avoid large variability in coating layer dimensions and properties. The gas injection nozzle was designed to protect precursor gases from becoming overheated prior to injection, to induce bed spouting and preclude bed stagnation in the bottom of the retort. Furthermore, the retort and injection nozzle designs minimize buildup of pyrocarbon and silicon carbide on the retort wall and manage nozzle orifice accretions. The equipment and operating methods have yielded very good reproducibility in the TRISO coated particles batches.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Soot inception limits in laminar diffusion flames with application to oxy-fuel combustion

For diffusion flames, the combination of oxygen enrichment and fuel dilution results in an increase in the stoichiometric mixture fraction, Z{sub st}, and alters the flame structure, i.e., the relationship between the local temperature and the local gas composition. Increasing Z{sub st} has been shown to result in the reduction or even elimination of soot. In the present work, the effects of variable Z{sub st} on soot inception are investigated in normal and inverse coflow flames, using ethylene as the fuel. Use of the inverse coflow flame underscores the validity of these concepts, since the convective field in the inverse flame directs particles into the fuel-rich region. Sooting limits based on particle luminosity are measured as a function of Z{sub st}. The sooting limit is obtained by varying the amount of inert gas until soot appears above a predefined height. For each limit flame, the adiabatic flame temperature is calculated and the flame temperature at the half-height is measured. The flame temperature at the sooting limit is found to increase with Z{sub st} for both normal and inverse flames. The effects of residence time are also investigated, and the sooting limit inception temperature is found to be dependent on fuel stream velocity for both the normal and inverse configurations. A simple model applicable to oxy-fuel combustion is presented which describes how increasing Z{sub st} results in the reduction and ultimately elimination of soot. This model assumes that soot inception can only occur in a region where critical values for species, temperature, and residence time are met. The soot inception region is shown to be bounded by two isotherms: a low-temperature boundary that is a function of residence time, and a high-temperature boundary that corresponds to the location of a critical local carbon-to-oxygen ratio. The effect of increasing Z{sub st} is to move the boundaries of the soot inception zone towards each other, until the zone is infinitely thin and thus the sooting limit is reached. By comparing the model to experimental data, a critical local C/O ratio of 0.53 and a sooting limit inception temperature of 1640 K (for a characteristic residence time of 22 ms) were determined for ethylene. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Sorption Mechanisms for Mercury Capture in Warm Post-Gasification Gas Clean-Up Systems

The research was directed towards a sorbent injection/particle removal process where a sorbent may be injected upstream of the warm gas cleanup system to scavenge Hg and other trace metals, and removed (with the metals) within the warm gas cleanup process. The specific objectives of this project were to understand and quantify, through fundamentally based models, mechanisms of interaction between mercury vapor compounds and novel paper waste derived (kaolinite + calcium based) sorbents (currently marketed under the trade name MinPlus). The portion of the research described first is the experimental portion, in which sorbent effectiveness to scavenge metallic mercury (Hg{sup 0}) at high temperatures (>600 C) is determined as a function of temperature, sorbent loading, gas composition, and other important parameters. Levels of Hg{sup 0} investigated were in an industrially relevant range ({approx} 25 {micro}g/m{sup 3}) although contaminants were contained in synthetic gases and not in actual flue gases. A later section of this report contains the results of the complementary computational results.

01 COAL, LIGNITE, AND PEAT↗

PLASMA ETCHING RATES AND SURFACE COMPOSITION OF BULK NIOBIUM TREATED IN Ar/Cl2 MICROWAVE DISCHARGE

To achieve theoretically predicted values of the accelerating fields in superconducting radiofrequency (SRF) cavities, their inside surface should be fairly smooth and free of impurities. Thus, surface preparation is the critical step in production of SRF cavities. Plasma etching process is a dry chemistry technique that can be used to achieve these requirements. It is based on interaction between reactive halogen species produced in the glow discharge and the surface. During this process, volatile Nb halides are evaporated from the surface of Nb, removing the mechanically damaged and contaminated layer. We present a treatment of bulk Nb samples in the Ar/Cl2 microwave discharge. We have shown that etching rates of bulk Nb as high as 1.5 mm/min can be achieved without introducing impurities in Nb. The rate dependence on various discharge parameters and reactive gas composition is presented. Surface composition and topology measurements were carried out before and after plasma treatment

43 PARTICLE ACCELERATORS↗

Distinguishing Plasma Contributions to Catalyst Performance in Plasma-Assisted Ammonia Synthesis

Plasma-assisted catalysis is the process of electrically activating gases in the plasma-phase at low temperatures and ambient pressure to drive reactions on catalyst surfaces. Plasma-assisted catalytic processes combine conventional heterogeneous surface reactions, homogeneous plasma phase reactions, and coupling between plasma-generated species and the catalyst surface. Herein, we perform kinetically controlled ammonia synthesis measurements in a dielectric barrier discharge (DBD) plasma-assisted catalytic reactor. We decouple contributions due to plasma phase reactions from the overall plasma-assisted catalytic kinetics by performing plasma-only experiments. By varying the gas composition, temperature, and discharge power, we probe how macroscopic reaction conditions affect plasma-assisted ammonia synthesis on three different γ-alumina-supported transition metal catalysts (Ru, Co, and Ni). Our experiments indicate that the overall reaction and plasma-phase reaction are first-order in both N 2 and H 2 . In contrast, the rate contributions due to plasma-catalyst interactions are first-order in N 2 but zeroth order in H 2 . Furthermore, we find that the tuning of the plasma discharge power is more effective in controlling catalytic performance than the increasing of bulk gas temperature in plasma-assisted ammonia synthesis. Lastly, we show that adding a catalyst to the DBD reaction alters the way that productivity scales with the specific energy input (SEI).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗