Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fusion science”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Tantalum Suboxide Films with Tunable Composition and Electrical Resistivity Deposited by Reactive Magnetron Sputtering

Tantalum-based films with tailored composition, density, and electrical resistivity are of interest for next generation hohlraums for magnetized indirect-drive inertial confinement fusion. Here, we use reactive direct-current magnetron sputtering to deposit tantalum suboxide films with O content in the range of 46–71 at.%. In contrast to a common approach involving varying reactive gas contents, compositional control is achieved kinetically by changing the total chamber pressure and the deposition rate, while keeping the working gas mix of Ar-5%O2 constant. The resultant films are X-ray amorphous with electrical resistivity varying by over seven orders of magnitude. The dominant conduction mechanism changes from metallic to activated tunneling above ∼55 at.% of O, which is characterized by a sharp increase in resistivity and a decrease in the carrier density at low temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Temperature-dependent model of helium bubble expansion and bursting in tungsten

Continuum-scale models that can reliably predict the behavior of helium in tungsten are of interest to the fusion community due to the projected impact of these materials on fusion reactor operation. In this work, we perform molecular dynamics simulations of spherical helium bubbles of various sizes in tungsten at different temperatures and depths with the goal of determining a mathematical model of the pressure and density at which the bubbles initially expand or burst as a function of depth, size, temperature, and surface orientation. The bubbles are small enough that their loop-punching pressures cannot be accurately predicted with continuum mechanics, and their expansion behavior is important, as it appears to cause many of the features observed on helium-irradiated tungsten surfaces. We vary the temperature, bubble size, bubble depth, and surface orientation in each case, recording the bubble pressure and density that result in bubble expansion. An exponential function with three adjustable parameters is found to fit the results well; the parameters that best fit our results are provided.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Density Functional Theory Analysis of Candidate Tritium Permeation Barriers for Vanadium Alloys as a Fusion Structural Material

Vanadium alloys are being considered as a candidate structural material for the breeder blanket component of future fusion reactors due to their good thermal conductivity, low activation, and chemical compatibility with FLiBe. However, vanadium has a high hydrogen solubility, resulting in hydrogen diffusion and trapping in the vanadium structural alloy and lower than expected tritium breeding ratios. To mitigate the permeation of hydrogen into the structural alloy, a tritium permeation barrier will be coated onto the vanadium alloy. Multiple materials have been proposed as candidate tritium permeation barriers, but the extent to which each of these materials impacts hydrogen diffusion and trapping is still unknown. In this project, we perform atomic-scale calculations to narrow down the list of potential tritium permeation barrier candidates and to understand the mechanisms through which hydrogen diffusion is affected in these materials.

36 MATERIALS SCIENCE↗
DOE OSTI2023

A framework for forming thermoset polymer networks during laser powder bed fusion additive manufacturing

It is commonly reported that the limited availability of material types is a major barrier to widespread adoption for polymer laser powder bed fusion (PBF/L) additive manufacturing (AM). A deeper understanding of the physico-chemical relationships between AM process stimuli and polymer responsive behavior is needed to make data-driven decisions for PBF/L specific material development and formulation. Many researchers have cumulatively built the current state of PBF/L “science-based manufacturing” framework where an initial guess for process parameter values can be determined from measured polymer properties and the first-principles of physics. However, published literature has focused on developing this framework for thermoplastic processing of polymers omitting many specific concerns unique to processing thermosetting materials. The authors consider in the present work the implications of many specific aspects unique to thermosetting polymers during PBF/L manufacturing. These aspects are contextually discussed according to the five sub-functions of PBF/L and are described mathematically where appropriate alongside example data from thermosetting materials commercially available in powder form. Further, this expansion of the prevailing material development framework to include thermosetting polymers paves the way for the unique performance properties offered by that class to be manifest through AM’s geometric freedom.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Machine learning assisted prediction of tungsten heavy alloy plasma facing component performance for fusion energy applications

Tungsten and tungsten heavy alloys (WHAs), known for their remarkably high hardness, durability, and corrosion resistance, play a critical role in the thriving development of nuclear fusion reactors in recent years. However, the exploration in tungsten alloys for the nuclear-related applications has been limited by the difficulty of manufacturing and the complexity of experiments to reproduce the environment of nuclear reaction. Therefore, this project aims to utilize nanoscale simulation methods such as density functional theory (DFT) and molecular dynamics (MD) with the help of machine learning techniques to not only understand the mechanisms of tungsten alloys but also allow us to computationally predict their mechanical behaviors under extreme environments. One critical problem of the application of WHAs in nuclear reactors is the surface melting. In the current design of the SPARC reactor, the WHA, W97Ni2.1Fe0.9 or W97NiFe, is chosen to be the first wall components to confine the plasma where the particles are fiercely moving and colliding into each other to create nuclear fusion reaction. This process will generate extremely high heat flux onto these WHA tiles, leaving high surface temperature that could possibly melt the surface of the WHA tiles, As illustrated in Fig. 1(a). a laser experiment previously done illustrates that a rough surface damage would be made after the surface melting where the matrix area mainly composed of nickel and iron as shown in Fig. 1(b), will first melt and then leave vacancies between these tungsten grains. Unfortunately, these kinds of roughness on the first-wall components could be deadly to the plasma inside a Tokmak reactor because the heat that is supposed to dissipate at a designed ratio through the tiles may in turn be excessively absorbed and accumulated on any uneven area of the surface, which will eventually make the whole nuclear reaction fail. In this project, we will introduce a machine learning potential, Allegro, based on DFT calculation and then build a MD model for W-Ni-Fe alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Height-resolved emission spectroscopy and high-speed imaging of the TiAl6V4 vapor plume under laser powder bed fusion conditions

Optical emission spectroscopy is increasingly used as an in situ monitoring technique during laser powder bed fusion (LPBF) because plume emission holds elemental information not found in other in situ sensing techniques. This work explores the shape, stability, and temperature of the emission plume above the melt pool of Ti6Al4 V undergoing laser scans under LPBF-like processing conditions, using high-speed video and height-resolved spectroscopy to study the details of plume dynamics. Optical emission spectroscopy is conducted in the 480 nm to 525 nm region, where Ti emission is strong, with 0.3 mm vertical resolution above the baseplate. The Boltzmann plot method is used to determine temperature at each probed elevation, which indicates that the hottest location of the plume is occasionally elevated 0.3 mm to 0.6 mm above the scanning surface. The results show that the plume shape, stability, temperature, and spectra are highly dependent on the processing conditions. We highlight some of the complexities of optical emission spectroscopy and discuss potential challenges for implementing optical emission spectroscopy across an entire build.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Optimization of direct aging temperature of Ti free grade 300 maraging steel manufactured using laser powder bed fusion (LPBF)

Maraging steels are of interest to the tool and die industry owing to their high strength, toughness and machinability. Additive manufacturing technologies like laser powder bed fusion (LPBF) can result in a paradigm shift in the design of maraging steel tools. Here, the lack of precipitates, in combination with solute segregation and non-equilibrium microstructure in Grade 300 maraging steel fabricated via LPBF makes the steel amenable to strengthening via direct aging post fabrication instead of the conventional solution treatment and aging. In this study we have focused on optimizing the direct aging temperature for a Ti-free Grade 300 maraging steel fabricated via LPBF for two different aging times. Through strain hardening analysis and detailed microstructural characterization, we show that direct aging at a temperature of 440 °C for 6 h resulted in the best strength-ductility combination. Aging samples at a lower temperature or shorter time resulted in no strain hardening prior to necking as a result of lower fraction of reverted austenite, whereas aging samples at a higher temperature resulted in extensive recrystallization of martensite, coarsening of precipitates, and extensive austenite reversion, resulting in softening of the fabricated parts.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The origin and formation of oxygen inclusions in austenitic stainless steels manufactured by laser powder bed fusion

The origins of nano-scale oxide inclusions in 316L austenitic stainless steel (SS) manufactured by laser powder bed fusion (L-PBF) was investigated by quantifying the possible intrusion pathways of oxygen contained in the precursor powder, extraneous oxygen from the process environment during laser processing, and moisture contamination during powder handling and storage. When processing the fresh, as-received powder in a wellcontrolled environment, the oxide inclusions contained in the precursor powder were the primary contributors to the formation of nano-scale oxides in the final additive manufactured (AM) product. These oxide inclusions were found to be enriched with oxygen getter elements like Si and Mn. By controlling the extraneous oxygen level in the process environment, the oxygen level in AM produced parts was found to increase with the extraneous oxygen level. The intrusion pathway of this extra oxygen was found to be dominated by the incorporation of spatter particles into the build during processing. Moisture induced oxidation during powder storage was also found to result in a higher oxide density in the AM produced parts. SS 316L powder free of Si and Mn oxygen getters was processed in a well-controlled environment and resulted in a similar level of oxygen intrusion. Finally, microhardness testing indicated that the oxide volume fraction increase from extraneous oxygen did not influence hardness values. However, a marked decrease in hardness was found for the humidified and Si-Mn free AM processed parts.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Solid breeder material crystal structure evolution due to Li burn up–Loss of crystal stability

Solid breeder materials for fusion power plants are subjected to extreme conditions of radiation damage, high temperature and designed component burn-up. Here, the loss of lattice stability of Li 2 TiO 3 due to Li burn-up was investigated using first principles-based approaches to aid evaluation of upper limit of component lifetime. The lattice stability is analyzed using calculated phonon dispersion in the Li 2 TiO 3 supercell, while Li burn-up is modeled by the introduction of Li-vacancies. It has been determined that the studied ceramic can be structurally stable up to ~40% of Li atoms burn-up. At 50% burn-up, the negative frequency branch in the phonon dispersion spectrum appears indicating the loss of lattice dynamical stability. Moreover, the structure obtained by introduction of unstable frozen phonons with minima energy amplitude also results in a phonon dispersion with negative branches in the structure obtained. Therefore, the system completely loses stability when approximately half of Li atoms are consumed.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effects of Build Orientation and Heat Treatment on Neutron Irradiation Hardening in Inconel 625 Fabricated via Laser Powder Bed Fusion

Various Inconel 625 coupons fabricated via Laser Powder Bed Fusion (L-PBF) were neutron irradiated using the inside reflector of the reactor at the University of Missouri Research Reactor (MURR). Effects of build orientation and heat treatment on neutron-induced hardening were investigated by inspecting L-PBF samples built vertically or at a 45º angle in the following heat-treated conditions: as-built (no heat treatment), 700 ºC for 1 hour, 900 ºC for 1 hour, and 1050 ºC for 1 hour. The microhardness results of L-PBF samples before and after neutron irradiation were compared with traditional wrought Inconel 625. All samples underwent an irradiation flux of 6.61 x 1013 neutrons/cm²/s for 310 hours for an estimated damage of 0.012 dpa. Results indicate that as-built L-PBF specimens are less prone to radiation hardening relative to their wrought counterparts. As-printed diagonal specimens were shown to harden by 8% as compared to 1.2% hardening in as-printed vertical specimens.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Design and Analysis of an Advanced Three-Point Bend Test Approach for Miniature Irradiated Disk Specimens

Candidate tungsten armor materials in a magnetic confinement fusion device must be able to withstand thermal variation that leads to internal stresses caused by the impinging heat load. In addition, the thermomechanical properties of these materials are degraded by irradiation-induced defect accumulation. Fission reactor–based irradiation data are used to predict the fusion neutron damage and property change. This study examines the motivation and design of a custom-designed three-point bend test for neutron-irradiated disk specimens that are 3 mm in diameter to be able to define the flexural strength of advanced tungsten materials, alloys, and composites—and to the extent that embrittlement occurs after neutron irradiation. The theory provided shows a calculation for the flexural deflection and shear deflection due to the small-geometry constraints. A finite element deformation analysis is performed to evaluate the mechanical stress field of disk bend specimens. The stress values above 80% of the maximum stress are concentrated in 2.4 mm of the 3.0-mm length of the centerline across the tungsten disk diameter. A bend test fixture has been designed and fabricated to enable testing of these specimens with precisely engineered tolerance and minimal machine compliance. This fixture will be able to be placed inside a universal testing frame at elevated temperatures for the mechanical property evaluation of future neutron-irradiated disk specimens.

36 MATERIALS SCIENCE↗
DOE OSTI2025

MOOSE-based Tritium Migration Analysis Program, Version 8 (TMAP8) for advanced open-source tritium transport and fuel cycle modeling

Tritium management is critical for the safety, sustainability, and economics of fusion energy systems, and advanced and reliable modeling tools help accelerate the development of tritium technologies. This paper presents the Tritium Migration Analysis Program, Version 8 (TMAP8), an open-source, MOOSE-based application developed to provide state-of-the-art tritium transport and fuel cycle modeling capabilities. TMAP8 aims to expand the capabilities of previous versions (i.e., TMAP4 and TMAP7) by leveraging modern computational techniques, ensuring high software quality assurance standards (key to building trust), and enabling multispecies, multiscale, and multiphysics simulations for integrated tritium transport modeling in complex geometries. This paper outlines TMAP8’s scope and rigorous development practices, emphasizing its transparency, accessibility, modularity, and reliability. We present the current suite of verification and validation cases based on those from TMAP4, demonstrating TMAP8’s accuracy and reliability against analytical solutions and experimental data. Additionally, the paper showcases TMAP8’s integrated fuel cycle modeling capabilities, highlighting its applicability at various scales and levels. The TMAP8 code and documentation are openly available, promoting collaborative development and widespread adoption within the fusion community. Future work will soon expand TMAP8’s verification and validation suite to include those from TMAP7 and other recent experimental studies for validation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

TRITIUM TRANSPORT MODELING AT THE PORE SCALE IN CERAMIC BEEDER MATERIALS USING TMAP8

Fusion reactors depend on the blanket material to breed and release tritium at the same rate or faster than it is consumed by the fusion reaction. Cellular ceramic breeders are dense materials that can maintain a high tritium breeding ratio while promoting tritium release thanks to highly connected pores. Assessing the tritium breeding capabilities of these materials requires a combination of extensive experimental and modeling efforts. In this work, we develop and calibrate a multiphysics model of tritium transport. This novel model accounts for ceramic and pore diffusion, trapping and detrapping, and several surface reactions at the pore surface. We perform a sensitivity analysis and calibrate the model by comparing its predictions against experimental measurements of deuterium absorption. The calibrated model is then used to model tritium absorption in samples with different pore microstructures to investigate the effect of pore interconnectivity on tritium absorption. The model is part of the development of the multiscale, multiphysics framework for tritium transport (i.e., the Tritium Migration Analysis Program [TMAP8]), which is itself built on top of the finite element multiphysics framework MOOSE. This study demonstrates some of TMAP8’s capabilities, and is the first step toward assessing the tritium breeding capabilities of ceramic breeder material designs.

08 HYDROGEN↗
DOE OSTI2025

Localized orientation gradients in additively manufactured stainless steel 316H structures

The high solidification rates during additive manufacturing cause highly localized thermal and strain gradients. The effect of these gradients on the evolution of local orientation misorientations within a grain is not well understood. In this study, stainless steel 316H parts were fabricated via laser powder bed fusion using three different energy densities: 43, 71, and 135 J/mm 3 . Electron backscatter diffraction showed that the maximum misorientations of the grains can be up to 25° along the build direction. Misorientation gradients (RM g ) within grains are process-dependent and can change from 0.036°/μm to 0.015°/μm with increased volumetric energy densities. In conclusion, the characterized misorientation gradients are an indication of the level of dislocations and, to an extent, the plastic deformation resulting from the rapid solidification during laser powder bed fusion.

316H↗
DOE OSTI2022

Calibration of a mesoscale tritium transport model for ceramic breeder materials in TMAP8 using experimental data

Due to the scarcity of the long-term external tritium supply, lithium-containing breeder materials are used in the blanket of fusion reactors to produce tritium faster than the deuterium-tritium fusion reaction consumes it. A cellular breeder is a promising material with higher lithium density and thermal conductivity than conventional ceramic pebbles and enhanced tritium extraction with interconnected pores. Although several experimental and modeling efforts have improved our understanding of tritium transport, the exact mechanisms governing tritium release from breeder materials are still unknown. As a result, current models cannot reliably assess the tritium breeding capabilities of cellular breeder materials. This work presents a tritium transport multiphysics model and calibrates it using experimental data of deuterium absorption and desorption from cellular breeder materials at different temperatures and pressures. This model accounts for ceramic and pore diffusion, trapping and detrapping, and several surface reactions at the pore surface. After calibrating the model and performing sensitivity analysis, we discuss pre-dominant mechanisms governing tritium release from cellular breeder materials. The model is part of the Tritium Migration Analysis Program [TMAP8], a multiscale, multiphysics framework for tritium transport based on the finite element multiphysics framework MOOSE. This study demonstrates some of TMAP8’s capabilities and provides insight into the mechanisms governing tritium transport in cellular ceramic breeder materials.

08 HYDROGEN↗
DOE OSTI2023

Hydrogen and deuterium permeation in Hastelloy N

Hastelloy N was chosen as the fluoride salt-contacting structural material for the Molten Salt Reactor Experiment due to its excellent compatibility with the fuel salt FLiBe. FLiBe is currently investigated for several advanced fusion and fission reactor concepts where tritium generation in the FLiBe is anticipated. Knowledge of hydrogen transport properties through Hastelloy N is important to understand how tritium would permeate through this material and result in an unintentional release. In this study, the hydrogen and deuterium permeability, diffusivity, and solubility were measured from 500 to 700 °C at a primary-side pressure of 10 kPa in a well-characterized sample of Hastelloy N. The prepared polycrystalline Hastelloy N had C and O impurities present on the surface. These impurities were investigated using Auger Emission Spectroscopy and Ar depth profiling. Here, the adventitious C was removed upon the first Ar sputter cycle whereas O persisted deeper into the sample. For permeation experiments, applied deuterium pressures ranged from 13 Pa to 100 kPa and deuterium transport remained in the diffusion-limited regime (J ∝ P 0.5 ) throughout the pressure range examined. Two methods are employed to measure the effective hydrogen and deuterium diffusivity: rise and decline. The decline method produced improved statistical model fits for calculating the effective diffusion coefficient compared to the rise method. The resultant transport properties compared well to published values for other nickel alloys.

08 HYDROGEN↗
DOE OSTI2025

Multi-fidelity equations of state and transport coefficient datasets for pulsed-power applications

Reliably simulating experiments relevant to the National Nuclear Security Administration (NNSA) requires a detailed description of material properties across a wide range of conditions. Such properties include the equations of state, charged-particle transport coefficients, and optical properties like the opacity. Together, these properties make up the material models used in radiation-magnetohydrodynamic simulations of nuclear fusion experiments. Many of these models do not incorporate uncertainties in the data used to produce them. It is unknown whether these uncertainties significantly impact the interpretation of simulation results and diagnostics. The purpose of this work is to quantify how such uncertainties impact simulations of pulsed-power experiments. We accomplished this task by first assessing discrepancies between approaches used to generate the data. This included bringing together members of the high-energy-density community spanning the three NNSA laboratories and multiple universities. Then, using these data, we developed a general framework that systematically incorporates physical uncertainties within the material models suitable for uncertainty quantification analyses. The framework utilizes machine learning, Bayesian inference, and incorporates multi-fidelity datasets. We demonstrated the framework by quantifying the impact that material model uncertainties have on simulations of pulsed-power experiments underway on Z at Sandia National Laboratories. As a result of this work, we discovered that modest uncertainties in material models (roughly 20%) correspond to significant uncertainties in the outputs from simulations. Our framework has enabled rapid construction of material models through an automated procedure and allows for the generation of material models of interest to the NNSA.

36 MATERIALS SCIENCE↗