SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Cavitation-erosion experimental data previously covering several materials tested in a rotating disk device and a magnetostriction apparatus were analyzed using new normalization and curve-fitting techniques. From this process a universal approach is derived which can include data from cavitation and liquid impingement studies for specific materials from different test devices.
Small-scale force and moment and pressure models based on the outer mold lines of the Ares I design analysis cycle crew launch vehicle were tested in the NASA Langley Research Center Unitary Plan Wind Tunnel from May 2006 to September 2009. The test objectives were to establish supersonic ascent aerodynamic databases and to obtain force and moment, surface pressure, and longitudinal line-load distributions for comparison to computational predictions. Test data were obtained at low through high supersonic Mach numbers for ranges of the Reynolds number, angle of attack, and roll angle. This paper focuses on (1) the sensitivity of the supersonic aerodynamic characteristics to selected protuberances, outer mold line changes, and wind tunnel boundary layer transition techniques, (2) comparisons of experimental data to computational predictions, and (3) data reproducibility. The experimental data obtained in the Unitary Plan Wind Tunnel captured the effects of evolutionary changes to the Ares I crew launch vehicle, exhibited good agreement with predictions, and displayed satisfactory within-test and tunnel-to-tunnel data reproducibility.
Propellers used for electric vertical takeoff and landing (eVTOL) aircraft propulsion systems experience a wide range of aerodynamic conditions, including significant incidence angles relative to oncoming airflow. Propellers in oblique flow exhibit deviations in thrust and torque oriented along their axis of rotation, as well as significant off-axis forces and moments. Although important for understanding eVTOL aircraft aerodynamics, sparse experimental data exist for propellers operating at incidence. This report describes an experimental wind tunnel study of isolated propeller aerodynamics across a wide range of flight conditions expected to be experienced by the LA-8 tandem tilt-wing, eVTOL aircraft. The experimental data obtained from the study are graphically presented and a discussion of observed aerodynamic phenomena is compared to theoretical expectations and past experimental work. The content of this report is intended to provide guidance to future propeller testing efforts and describe pertinent propeller aerodynamic behavior expected to be experienced by eVTOL vehicles.
Research accomplishments in the following areas are discussed: (1) the calibration of the gas chromatograph for acetaldehyde and ethanol; (2) the development of data reduction and analysis methods; (3) the generation and analysis of experimental data for the transport of 100 ppm acetaldehyde through a cylindrical bed packed with activated carbon granules; (4) the generation and analysis of experimental data for the transport of 100 ppm ethanol through a cylindrical bed packed with activated carbon granules; and (5) a comparison of the volume adsorption capacity of activated carbon for 100 ppm concentrations of acetaldehyde, ethanol, and acetone. Activities in progress and planned activities are reviewed.
Previously, studies that determined the partition coefficient for an element, i, between plagioclase and the residual basaltic melt (Di plag) have been conducted using experimental conditions dissimilar from the Moon, and thus these values are not ideal for modeling plagioclase fractionation in a lunar system. However, recent work [1] has determined partition coefficients for plagioclase at lunar oxygen fugacities, and resulted in plagioclase with Anorthite contents ≥An90; these are significantly more calcic than plagioclase in previous studies, and the An content has a profound effect on partition coefficient values [2,3]. Plagioclase D-values, which are dependent on the An content of the crystal [e.g., 2-6], can be determined using published experimental data and the correlative An contents. Here, we examine new experimental data from [1] to ascertain their effect on the calculation of equilibrium liquids from Apollo 16 sample 60635,2. This sample is a coarse grained, subophitic impact melt composed of ~55% plagioclase laths with An94.4-98.7 [7,8], distinctly more calcic than of previous partition coefficient studies (e.g., [3-6, 9-10]). Sample 60635,2 is notable as having several plagioclase trace element analyses containing a negative Europium anomaly (-Eu) in the rare-earth element (REE) profile, rather than the typical positive Eu anomaly (+Eu) [7-8] (Fig. 1). The expected +Eu is due to the similarity in size and charge with Ca2+, thereby allowing Eu2+ to be easily taken up by the plagioclase crystal structure, in contrast to the remaining REE3+. Some 60635,2 plagioclase crystals only have +Eu REE profiles, some only have -Eu REE profiles, and some +Eu and -Eu analyses in different areas on a single crystal [7, 8]. Moreover, there does not seem to be any core-rim association with the +Eu or -Eu analyses, nor does there appear to be a correlation between the size, shape, or location of a particular crystal within the sample and the sign of its Eu anomaly, which suggests a complex evolution. In order to investigate this sample further, we can calculate the equilibrium liquids, but with An contents distinct from previous experimental studies, we must calculate the appropriate partition coefficients for each trace element analysis.
The structural integrity of proposed high speed aircraft can be seriously affected by the extremely high surface temperatures and large temperature gradients throughout the vehicle's structure. Variations in the structure's elastic characteristics as a result of thermal effects can be seen by changes in vibration characteristics. Analysis codes that predict these changes must be correlated and verified with experimental data. Analytical and experimental modal test results are given from uniform, nonuniform, and transient thermoelastic vibration tests of a 12 x 50 x 0.19 aluminum plate. The data show the effect of heat on the modal characteristics of the plate. The results showed that frequencies decreased, damping increased, and mode shapes remained unchanged as the temperature of the plate increased. Analytical predictions provided good correlation with experimental results.
This paper presents an asymptotic method for the analysis of the interference of multiple tractor propeller slipstream with large aspect ratio swept wings. It is assumed that the height of the slipstream is of the order of the wing chord and its spanwise extent is of the order of the wing span. Three different flow regions are identified by employing different stretching transformations. Asymptotic expansions are made in each of the three regions, using the chord to span ratio as the small expansion parameter. The details of the nonuniform flow in the slipstream enter into the wing sectional analysis. In the outer limit, the wing shrinks to a swept lifting line, and the slipstream reduces to a thin sheet of jet carrying the momentum gain from the propeller. The curvature of this jet sheet results in a pressure difference which is represented by a vortex sheet. The governing equations are solved by discretization. Several examples are considered for which experimental data are available. Comparison of the present results with the experimental data as well as other numerical solutions showed generally good agreement.
The Baldwin-Lomax algebraic turbulence model was modified for hypersonic flow conditions. Two coefficients in the outer layer eddy viscosity model were determined as functions of Mach number and temperature ratio. By matching the solutions from the Baldwin-Lomax model to those from the Cebeci-Smith model for a flat plate at hypersonic speed, the new values of the coefficient were obtained. The results show that the values of C sub cp and C sub kleb are functions of both Mach number and wall temperature ratio. The C sub cp and C sub kleb variations with Mach number and wall temperature were used for the calculations of both a 4 deg wedge flow at Mach 18 and an axisymmetric Mach 20 nozzle flow. The Navier-Stokes equations with thin layer approximation were solved for the above hypersonic flow conditions and the results were compared with existing experimental data. The agreement between the numerical solutions and the existing experimental data were good. The modified Baldwin-Lomax model thus is useful in the computations of hypersonic flows.
The Baldwin-Lomax (1978) algebraic turbulence model was modified for hypersonic flow conditions. Two coefficients in the outer-layer eddy-viscosity model were determined as functions of Mach number and temperature ratio. By matching the solutions from the Baldwin-Lomax model to those from the Cebeci-Smith (1974) model for a flat plate at hypersonic speed, the new values of the coefficients were obtained. The results show that the values of C(cp) and C(kleb) are functions of both Mach number and wall temperature ratio. The C(cp) and C(kleb) variations with Mach number and wall temperature were used for the calculations of both a 4-deg wedge flow at Mach 18 and an axisymmetric Mach 20 nozzle flow. The Navier-Stokes equations with thin-layer approximation were solved for the above hypersonic flow conditions and the results were compared with existing experimental data. The agreement between the numerical solutions and the existing experimental data were good. The modified Baldwin-Lomax model thus is useful in the computations of hypersonic flows.
The feasibility was determined of incorporating the Navier-Stokes computational code, CFL3D, into the supersonic wing design process. The approach taken is of two steps. The first step was to calibrate CFL3D against existing experimental data sets obtained on thin sharp edged delta wings. The experimental data identified six flow types which are dependent on the similarity parameters of Mach number and angle of attack normal to the leading edge. The calibration showed CFL3D capable of simulating these various separated and attached flow conditions. The second step was to use CFL3D to study the initial formation of leading edge separation over delta wings at supersonic speeds. This consisted of examining solutions obtained on a 65 deg delta wing at Mach number of 1.6 with varying cross sectional shapes. Reynolds number was held constant at 1000000 and the Baldwin-Lomax turbulence model was used. The study showed that through the use of leading edge radius and/or camber, the onset of leading edge separation can be delayed to a higher angle of attack than observed on a flat sharp edged wing. Based on the geometries studied, three wind tunnel models are being designed to verify these results.
Thin solar sail membranes of very large span are being envisioned for near-term space missions. One major design issue that is inherent to these very flexible structures is the formation of wrinkling patterns. Structural wrinkles may deteriorate a solar sail's performance and, in certain cases, structural integrity. In this paper, a geometrically nonlinear, updated Lagrangian shell formulation is employed using the ABAQUS finite element code to simulate the formation of wrinkled deformations in thin-film membranes. The restrictive assumptions of true membranes, i.e. Tension Field theory (TF), are not invoked. Two effective modeling strategies are introduced to facilitate convergent solutions of wrinkled equilibrium states. Several numerical studies are carried out, and the results are compared with recent experimental data. Good agreement is observed between the numerical simulations and experimental data.
A three-Dimensional computational model is used to simulate flow in a non-axisymmetric, convergent-divergent nozzle incorporating porous cavities for shock-boundary layer interaction control. The nozzle has an expansion ratio (exit area/throat area) of 1.797 and a design nozzle pressure ratio of 8.78. Flow fields for the baseline nozzle (no porosity) and for the nozzle with porous surfaces of 10% openness are computed for Nozzle Pressure Ratio (NPR) varying from 1.29 to 9.54. The three dimensional computational results indicate that baseline (no porosity) nozzle performance is dominated by unstable, shock-induced, boundary-layer separation at over-expanded conditions. For NPR less than or equal to 1.8, the separation is three dimensional, somewhat unsteady, and confined to a bubble (with partial reattachment over the nozzle flap). For NPR greater than or equal to 2.0, separation is steady and fully detached, and becomes more two dimensional as NPR increased. Numerical simulation of porous configurations indicates that a porous patch is capable of controlling off design separation in the nozzle by either alleviating separation or by encouraging stable separation of the exhaust flow. In the present paper, computational simulation results, wall centerline pressure, mach contours, and thrust efficiency ratio are presented, discussed and compared with experimental data. Results indicate that comparisons are in good agreement with experimental data. The three-dimensional simulation improves the comparisons for over-expanded flow conditions as compared with two-dimensional assumptions.
This paper presents a two-phase computational fluid dynamics (CFD) model for simulating autogenous pressurization and expulsion in a cryogenic liquid hydrogen storage tank, utilizing a volume-of-fluid (VOF) approach combined with the kinetics-based Schrage equation to accurately capture the phase boundary and interfacial heat, mass, and momentum transfer between liquid and vapor phases. The model is validated against experimental data from NASA's K-site tank facility, specifically experimental case 225, which involved pressurization and controlled expulsion of liquid hydrogen. Various turbulence models are evaluated to assess their influence on model accuracy. The CFD simulations successfully replicate key thermodynamic behaviors observed during the experiments, including pressure evolution, temperature profiles, and phase-change dynamics at the vapor-liquid interface. The predicted tank pressures, temperatures, and pressurant requirements agree with experimental data, with pressurant mass predictions within 16\% of observed values. This study highlights the importance of selecting appropriate turbulence models to accurately simulate complex flow and heat transfer phenomena during tank pressurization and expulsion. By enhancing the accuracy and reliability of CFD models for liquid hydrogen under cryogenic conditions, this research contributes to developing efficient cryogenic propellant management strategies for future space missions.
This paper presents a two-phase computational fluid dynamics (CFD) model for simulating autogenous pressurization and expulsion in a cryogenic liquid hydrogen storage tank, utilizing a volume-of-fluid (VOF) approach combined with the kinetics-based Schrage equation to accurately capture the phase boundary and interfacial heat, mass, and momentum transfer between vapor and liquid phases. The model is validated against experimental data from NASA's K-site tank facility, specifically experimental case 225, which involved autogenous pressurization and controlled expulsion of liquid hydrogen. Various turbulence models are evaluated to assess their influence on model accuracy. The CFD simulations successfully replicate key thermodynamic behaviors observed during the experiments, including pressure evolution, temperature profiles, and phase-change dynamics at the vapor-liquid interface. The predicted tank pressures and temperatures agree well with experimental data, whereas the pressurant mass predictions are within 16% of observed values. This study emphasizes the importance of selecting appropriate turbulence models to accurately simulate the complex flow and heat transfer phenomena during tank autogenous pressurization and expulsion. By improving the accuracy and reliability of CFD models for these processes, this research contributes to developing efficient cryogenic propellant management strategies for future space missions.
The problem of the calculation of ambient densities from San Marco-C neutral atmospheric composition experiment data is considered. A brief description is given of the data measurement method, followed by a description of both the theoretical and experimental data curves. Geometry, electrometer distortions, and noise effects are then studied in terms of their effects on the ideal data form. From these considerations two data reduction methods are evolved. The first is an iterative integration technique that exploits the symmetry of the experimental data about the minimum angle of attack. For the analysis of geometry effects, a second method using interval averaging was developed and studied.
The objective is to provide computer codes and/or correlations for application in the design of transient heat transfer systems. The mathematical models in the computer codes are being tested by experimental data obtained in the laboratory using optical techniques. The elimination of natural convection (buoyancy) in the experimental data obtained in zero-g (KC-135) facilitates the study of thermal expansion effects which is of interest in the development and testing of the mathematical models of the transient heat transfer. Initial flight in the KC 135 (June 1983) suggested some modifications to the experimental apparatus and the data acquisition technique (high speed video will replace high speed movies for recording optical records generated during the experiments). A series of KC-135 flights with this experiment on board are scheduled for summer/fall 1984. The acquisition of the aforementioned data using interferometry and beam deflection optical techniques is anticipated. The measurements provide time dependent temperature fields above a horizontal heater surface submerged in a static fluid (Freon 13). The heater surface is electrically heated for a time interval approximately 0.100 sec. during which the data are optically recorded.
Monte Carlo (MC) modeling has been used extensively to simulate electron scattering and x-ray emission from complex geometries. Here are presented comparisons between MC results and experimental electron-probe microanalysis (EPMA) measurements as well as phi(rhoz) correction algorithms. Experimental EPMA measurements made on NIST SRM 481 (AgAu) and 482 (CuAu) alloys, at a range of accelerating potential and instrument take-off angles, represent a formal microanalysis data set that has been widely used to develop phi(rhoz) correction algorithms. X-ray intensity data produced by MC simulations represents an independent test of both experimental and phi(rhoz) correction algorithms. The alpha-factor method has previously been used to evaluate systematic errors in the analysis of semiconductor and silicate minerals, and is used here to compare the accuracy of experimental and MC-calculated x-ray data. X-ray intensities calculated by MC are used to generate a-factors using the certificated compositions in the CuAu binary relative to pure Cu and Au standards. MC simulations are obtained using the NIST, WinCasino, and WinXray algorithms; derived x-ray intensities have a built-in atomic number correction, and are further corrected for absorption and characteristic fluorescence using the PAP phi(rhoz) correction algorithm. The Penelope code additionally simulates both characteristic and continuum x-ray fluorescence and thus requires no further correction for use in calculating alpha-factors.
The hypersonic turbulent wake produced by a wedge was studied experimentally and its properties were compared with predictions obtained from a numerical computation procedure. In the computation procedure several models for the eddy viscosity formulation of the turbulent transport were examined. Conventional-defect models and a modified mixing-length model were found to yield good predictions of the experimental data. The classical mixing-length model gave unrealistic results. The experimental data displayed similarity when velocity and temperature defects were scaled by the maximum defects and the transverse coordinate was scaled by the velocity-defect half-width.