Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “evaporation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Grey-box Fault Models and Applications for Low Carbon Emission CO2 Refrigeration System

CO2 refrigeration systems have attracted more attentions in recent years because of their zero-carbon emission advantages compared with traditional refrigerants. These systems are widely used in certain commercial buildings such as supermarkets. However, very limited energy studies have been done for such refrigeration systems under faults. Furthermore, this study investigated five common faults for supermarket transcritical CO2 refrigeration systems with display cases. The following major tasks were implemented for this study. (1) Five fault models (gray-box format) regarding the power consumption and supply air temperature were proposed for low- and high-temperature display cases, respectively. The models cover: ice accumulation on evaporator coil, evaporator fan partial failure, expansion valve failure, display door open, and condenser blockage. (2) These fault models were calibrated with field tests, and the modeling accuracies were in good agreement with measurement datasets. (3) The proposed fault models demonstrated more than 90% of fault detection for Fault Detection and Diagnostics (FDD) purposes for both field measurement and simulated data.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

Computational study of the ECN spray C via one-way coupling of internal nozzle flow and ensuing spray

Here, in this study, computational fluid dynamics simulations of the Engine Combustion Network Spray C injector were performed to investigate the effect of the internal nozzle flow on the development of the ensuing spray in automotive fuel injectors. A set of simulation best practices was first developed to achieve an accurate representation of the internal nozzle flow. Detailed, spatiotemporally defined information was extracted at the injector’s orifice exit and stored in maps that were subsequently employed to initialize a Lagrangian spray by means of a static, one-way coupling (OWC) approach. To highlight the impact of the in-nozzle flow on the spray, the OWC approach was compared with the conventional rate-of-injection (ROI) approach, for which the spray parcels are commonly initialized using a blob injection model. The results indicated that, using the ROI approach, considerable evaporation was observed within the plume in the near-nozzle region. On the other hand, the OWC approach showed evidence of evaporation farther downstream and at the plume periphery. The different behavior observed with the two approaches was mostly due to substantial differences in fuel mass distribution. The liquid fuel concentration predicted by the OWC approach matched well with X-ray tomography measurements of projected fuel mass per unit volume, in terms of both magnitude and distribution. In contrast, an unphysical distribution of fuel mass characterized by an extremely low liquid concentration was predicted by the ROI approach. In the far-field, the effect of the in-nozzle flow was found to be weaker as the spray penetrated and interacted with the ambient gas. In this region, the OWC and ROI approaches provided similar predictions of vapor penetration, spray morphology, and mixing-related characteristics.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Effect of laser scanning speed on the microstructure, phase transformation and mechanical property of NiTi alloys fabricated by $\mathrm{LPBF}$

This study investigated the effects of laser scanning speed on the microstructure, phase transformation and properties of NiTi alloys fabricated by laser powder bed fusion (LPBF). In this study, the contributions of metallurgical factors under different scanning speeds, such as Ni evaporation, Ni4Ti3 precipitation, dislocations and internal stress, to the transformation temperature and transformation latent heat were clarified through specially designed experiments. Ni evaporation is found to have the most profound effect, followed by precipitation. Increasing scanning speed is found to reduce Ni loss, thus cause less increase in the transformation temperature and transformation heat of the LPBF-NiTi alloys. Increasing scanning speed also increases the microstructure non-uniformity and thus widens the transformation temperature interval. The orientations of residual stress exhibit strong crystallographic stiffness dependence. The LPBF-NiTi alloys with different scanning speeds all exhibited high strains (>13.4%) and excellent shape memory effect. A LPBF-NiTi honeycomb structure exhibited 96% shape recovery rate after a 60% pre-compressive deformation. Besides, there is an optimum scanning speed for minimum porosity and smallest average pore size. However, the pore structure is found to have weak influence on the tensile behaviour of the LPBF-NiTi alloys, possibly due to the high defect tolerance of the martensitic transformation.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Open-air spray deposition of PCBM/BCP electron transport layer for inverted perovskite solar cells

A [6,6]-phenyl C61 butyric acid methyl ester (PCBM) and bathocuproine (BCP) electron transport layer (ETL) is spray deposited in open air directly on top of a perovskite at linear speeds of 9 m/min. The PCBM precursor ink contains a binary mixture of 1:1 chlorobenzene:chloroform, which optimizes spray wettability on the perovskite surface and allows quick solvent evaporation. A near-infrared heating module additionally provides a flash cure (<5 s) for the formation of smooth, large-area PCBM films (∼20 cm 2 ). A BCP solution in isopropanol is subsequently sprayed to form an ultrathin (<5 nm) film and characterized with a suite of high-resolution metrologies. The spray-deposition processing and near-infrared treatment do not damage the underlying perovskite. Inverted architecture devices containing the sprayed ETL achieve a champion efficiency of 20.3% and demonstrate stable performance without additional interlayers or surface treatments. Here, the technoeconomic cost of the open-air spray process is compared against traditional vacuum-based evaporation, resulting in a decrease in manufacturing costs by 26%.

14 SOLAR ENERGY↗
DOE OSTI2021

Conducting thermal energy to the membrane/water interface for the enhanced desalination of hypersaline brines using membrane distillation

Membrane distillation (MD) is a membrane-based thermal desalination process capable of treating hypersaline brines. Standard MD systems rely on preheating the feed to drive the desalination process. However, relying on the feed to carry thermal energy is limited by a decline of the thermal driving force as the water moves across the membrane, and temperature polarization. In contrast, supplying heat directly into the feed channel, either through the membrane or other channel surfaces, has the potential of minimizing temperature polarization, increasing single-pass water recoveries, and decreasing the number of heat exchangers in the system. When solar thermal energy can be utilized, particularly if the solar heat is optimally delivered to enhance water evaporation and process performance, MD processes can potentially be improved in terms of energy efficiency, environmental sustainability, or operating costs. Here we describe an MD process using layered composite membranes that include a high-thermal-conductivity layer for supplying heat directly to the membrane-water interface and the flow channel. Here, the MD system showed stable performance with water flux up to 9 L/m 2 /hr, and salt rejection >99.9% over hours of desalinating hypersaline feed (100 g/L NaCl). In addition to bench-scale system, we developed a computational fluid dynamics model that successfully described the transport phenomena in the system.

42 ENGINEERING↗
DOE OSTI2022

Numerical simulations of membrane distillation systems with actively heated membranes

Membrane distillation (MD) is a thermal desalination process that is gaining attention for treating hypersaline brines. One recent approach uses composite membranes with a thermally conductive layer that delivers heat to the membrane–feed interface, where it drives evaporation. Though this increases single-pass recovery, it comes with the challenge of promoting lateral heat conduction through the thin membrane. Herein, we develop a 3D, computational fluid dynamics (CFD) model that simulates conjugate heat, mass, and momentum transport in the feed channel and composite membrane. We then use the CFD to verify a simpler numerical model that approximates the feed velocity field analytically. We validate the numerical model experimentally, and use it to investigate the impacts of the conductive layer thickness, feed channel geometry, and operating conditions on temperature and concentration polarization, permeate production, and specific energy consumption. Overall, we find that lateral heating increases permeate production at the expense of increased concentration polarization. In extreme cases, the concentration increases more than four-fold along the membrane surface. Furthermore, we show however, that the feed flow rate and conductive layer thickness can be tailored to mitigate concentration polarization, for only a small reduction in permeate production.

42 ENGINEERING↗
DOE OSTI2024

Liquid lithium divertor analysis using coupled plasma material interaction model

A liquid lithium divertor can improve performance of future fusion devices by creating efficient power exhaust and improving the energy confinement via pumping of the hydrogen isotopes. In addition, significantly higher heat fluxes can be handled if controlled vapor shielding is used to redistribute the divertor heat flux over a wider area. Design and optimization of such a system calls for an analysis model which includes a strong two-way coupling between the plasma and divertor material. The incoming plasma heat and particle flux will affect the divertor surface temperature, which is a defining factor of the lithium evaporative and sputtered flux going into the plasma. Results of the coupled model based on the plasma edge code SOLPS-ITER and the computational fluid dynamics (CFD) code ANSYS-CFX will be presented for different configurations. An analytical slab flow model is used as a heat transfer boundary condition for SOLPS, defining particle flux from the wall via calculation of the surface temperature. At the final step, results of the SOLPS analysis are verified using a 3D CFD magnetohydrodynamics (MHD) analysis which uses heat and particle flux from SOLPS as a boundary condition. In addition to plasma heat flux, both analytical and CFD temperature models include several plasma material interaction effects, such as lithium evaporation, condensation and sputtering based on deuterium target flux. New adatom sputtering model based on the available experimental data is presented. Analytical model is expanded to include free surface axisymmetric configurations. Results of parametric studies of the divertor configurations with different lithium inlet temperature and velocity will be presented leading to the optimal design resulting in the lowest possible lithium contamination in the core.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Electrical injection and transport in Teflon-diluted hole transport materials

Diluting small molecule organic semiconductor hole transport materials with Teflon AF (TAF) dramatically increases their thermal/morphological stability while counterintuitively also increasing the current density in hole-only diodes. Here, we explore the origin of this current enhancement in co-evaporated blends of TAF and N,N'-Di(1-naphthyl)-N,N'-diphenyl-(1,1'-biphenyl)-4,4'-diamine (NPD) and find that it results from improved hole injection and not from a mobility enhancement due to semiconductor dilution effects. Whereas electroabsorption measurements indicate that an interface dipole shift of up to 0.5 eV (depending on TAF concentration) aides hole injection at the indium-tin-oxide anode, time-of-flight and temperature-dependent current-voltage measurements show that the mobility of 25 vol% TAF:NPD blends decreases by roughly an order of magnitude relative to neat NPD despite having slightly lower energetic disorder. For comparison, diluting with 25 vol% high density polyethylene achieves a similar reduction in energetic disorder but only decreases the mobility by a factor of two. Furthermore, these results highlight the tradeoff between reducing energetic disorder and frustrating percolation in diluted organic semiconductors, and represent a step toward thermally-evaporated polymer-small molecule composites that maintain high mobility while offering improved morphological stability and lower refractive index for organic light emitting diodes.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2026

A mathematical design framework for membrane pre-concentration in energy-efficient recovery of fermentation products

Due to the dilute nature of products manufactured via fermentation and cell-free bioprocessing, dewatering is a common unit operation in downstream processing (DSP) for bioproduct recovery, but it is typically energy intensive. To improve DSP energy efficiency for bio-based small molecules, integrating high-pressure membrane pre-concentration is a promising process option. However, this approach is typically constrained by a tradeoff between concentration factor (CF) and product recovery (PR), namely increasing the CF typically results in greater product loss, and vice versa. Here we developed a model that enables process design guidelines to: (i) identify scenarios in which the additional energy consumption and product loss from membrane pre-concentration are justified for use in DSP, and (ii) determine the optimal CF that minimizes process specific energy consumption. We compared the energy consumption of high-pressure membrane-integrated processes to evaporation-only processes and applied the model to an experimental case study for the separation and purification of butyric acid from Clostridium tyrobutyricum fermentation using an in situ product recovery (ISPR) process. The model estimated that integrating a tangential-flow reverse osmosis (RO) pre-concentration unit could reduce process energy consumption up to 45%. The use of advanced membrane pre-concentration technologies, such as negative rejection membranes and organic solvent reverse osmosis (OSRO), have the potential to further reduce the overall process specific energy consumption up to 96%, projected based on modeling. Overall, membrane pre-concentration, especially when strategically integrated prior to an evaporation step with optimized process conditions, holds significant potential for improving DSP energy efficiency, particularly in applications requiring substantial solvent removal for product recovery from dilute mixtures.

09 BIOMASS FUELS↗
DOE OSTI2020

Innovative high-temperature ammonium bifluoride fusion and rapid analysis of elements with nuclear forensic value

High-temperature ammonium bifluoride (ABF) fusions were evaluated for potential use in rapid dissolution of post-detonation nuclear debris. The ABF fusion was carried out in a Pt crucible which allowed evaluation of higher fusion and evaporation temperatures. The high-temperature ABF fusion dissolution method was evaluated using geological reference materials: USGS QLO-1a Quartz Latite, USGS SDC-1 Mica Schist, and NIST 278 Obsidian Rock. The optimized dissolution method involved a 10 min fusion at 540 °C, a 5 min reflux in 8 M HNO 3 , an evaporation at 300 °C and final dilution into 45 mL of 2% (v/v) HNO3. The final solution was filtered after heating at 105 °C using a hotblock. This dissolution method was simple, requiring only a hotplate or hotblock, filtered samples were available for ICP-MS analysis or radiochemical separation within 150 min, and was found to have high (>90%) recovery for many isotopes of interest in nuclear forensics applications. U and Pu in the dissolved material was separated using TEVA and UTEVA extraction chromatography columns, a process which resulted in >90% recovery. An irradiated U tracer was spiked into the material prior to dissolution and analyzed for recovery of major fission products and 239Np. The monitored radionuclides had recoveries of greater than 90%, except for the volatile radioiodine isotopes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Evaluation and optimization of flow boiling frictional pressure drop correlations using the data from traditional and next-generation refrigerants in a micro-fin tube

This study presents an experimental evaluation and optimization of flow boiling frictional pressure drop correlations for conventional and next-generation refrigerants in a horizontal micro-fin tube, with particular emphasis on the newly emerging refrigerant blends R-454C and R-455A, for which pressure-drop data in enhanced tubes remain limited. Experiments were conducted with R-410A, R-454C, R-455A, R-134a, R-1234yf, and R-1234ze(E) in a copper micro-fin tube with an inner diameter of 8.468 mm, over mass fluxes ranging from 100 to 300 kg/(m²·s) depending on the refrigerant, and evaporation temperatures of 7, 12, and 14 °C. Frictional pressure gradients were determined from measured total pressure drops after subtracting acceleration pressure drop, and the resulting database was used to assess four existing models: Kuo and Wang (1996), Cavallini et al. (1997), Goto et al. (2001), and Diani et al. (2014). The measured frictional pressure gradient increased with vapor quality and mass flux for all refrigerants and increased further at lower evaporation temperatures, with the overall trend strongly related to liquid viscosity. Among the four correlations, the Goto et al. (2001) model provided the best overall agreement with the measured data before optimization. To further improve prediction accuracy, the Kuo and Wang (1996) and Goto et al. (2001) models were optimized using the complete experimental database. After optimization, both models reduced the overall mean absolute deviation to below 15%, while the optimized Goto et al. (2001) model maintained the best and most consistent overall performance. The results provide new pressure-drop data for next-generation refrigerants and demonstrate that parameter optimization can significantly enhance the applicability of existing micro-fin-tube correlations.

Hu, Yifeng [ORNL] (ORCID:0000000242875185)↗
DOE OSTI2022

Describing the Influence of Ball-milling on the Amorphization of Flubendazole Using the PDF and RMC Methods with X-ray Powder Diffraction Data

Flubendazole (FBZ) is a poorly water-soluble drug, and different methodologies have been proposed to improve its oral bioavailability. Obtaining the amorphous drug phase is an alternative to improve its water solubility. Several techniques for drug amorphization, such as spray drying, lyophilization, melt quenching, solvent-evaporation, and ball milling, can yield various types of structural disorder and possibly render variations in physicochemical properties. Herein, we focus on evaluating the influence of the ball-milling process on the amorphization of FBZ. The characterization of the average global and local structures before, during, and after the milling process is described by sequential Rietveld refinements, pair distribution function analysis, and the Reverse Monte Carlo method. In conclusion, we show that preserving the local structure (nearest molecules) can be responsible for avoiding the fast structure recrystallization commonly observed when using the solvent-evaporation process for the studied drug.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2023

Orientational Order in Spin-Cast Lead-Iodide Perovskite Nanocrystal Solids

Combined synthetic control over size and composition renders colloidal lead-halide perovskite nanocrystals a tunable platform for high-efficiency optoelectronic applications. However, the properties and operational stability of devices based on nanocrystal solids are often dictated by the method of the evaporation-induced assembly. Ubiquitous slow evaporation techniques can produce highly ordered nanocrystal domains but limit the prospects for scalable fabrication of continuous device layers, calling for investigation of approaches to more rapidly form ordered perovskite nanocrystal solids. Here, we study orientationally ordered lead-iodide perovskite nanocrystal solids prepared by conventional spin coating with molecular additives (excess ligand) to enhance ordering within the arrays. In situ X-ray scattering measurements reveal that orientational ordering occurs rapidly upon solvent removal during spin coating and can be further enhanced by manipulating the spin speed. We vary the additive ligand length and explore trade-offs between ordering and layered perovskite impurity formation. Arrays treated with the intermediate-length octylamine ligand exhibit increased in-plane electronic conductivity, suggesting orientational ordering and internanocrystal electronic coupling can be enhanced by the treatment. In conclusion, these results highlight the prospects of establishing long-range order in lead-halide perovskite nanocrystal solids by using simple and fast coating methods.

14 SOLAR ENERGY↗
DOE OSTI2020

Volatilization Behavior of Supported Au Nanoparticle Arrays under H 2 at High Temperature

In this work, the fabrication and experimental study of model Au nanoparticle arrays (nanodots) was used to allow a direct comparison of reactive evaporation at elevated temperatures and nonambient H 2 -containing gas atmospheres with theoretical models. Strong temperature and H 2 -concentration dependencies were confirmed as expected, and the observed dependence in particle diameter with time was effectively described using a reactive evaporation and gas phase diffusion based quantitative model.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Overcoming Variability: A Reproducible Approach to SERS Detection of Nanodiamonds

Detonation nanodiamonds (DNDs) are formed at specific pressures and temperatures during explosions. Different explosives produce varied yields of DNDs within their detonation soot, with Composition B producing the highest yield. Raman spectroscopy (RS) is often used for the characterization of sp 2 - and sp 3 -hybridized carbon allotropes in carbonaceous materials because of distinct disorder and graphitic bands. Bulk diamond also gives a distinct Raman peak at 1332 cm –1 . Furthermore, as bulk diamond decreases in size to nanometer-sized species, the peak red-shifts and broadens, becoming increasingly difficult to detect with RS using visible excitations. Therefore, surface-enhanced Raman spectroscopy (SERS) was used to enhance the diamond peak of DNDs, enabling better detection and faster examination of DNDs within detonation soot. Previous literature of the SERS of DNDs delivered inconsistent results in spectral signatures and SERS substrates. Herein, refining of the methodology for the acquisition of SERS spectra of DNDs was achieved. Before any SERS experiments, the DNDs were first characterized with normal Raman (NR) and scanning electron microscopy. Two routes for SERS enhancement were evaluated: colloidal noble metal nanoparticles and evaporated silver films. Silver films produced the best signal enhancement of DNDs with the best signal-to-noise and peak enhancements observed at 20–30 nm thick silver films at 5% (∼300 μW) laser power. Consistent, reproducible SERS spectra were acquired of small aggregates of DNDs down to ∼500 nm. NR and SERS mapping analysis of DNDs before and after evaporation of silver films revealed the improvements in the detection capabilities of SERS compared with NR.

Carbon↗
DOE OSTI2021

A Direct Probe of the Hydrogen Bond Network in Aqueous Glycerol Aerosols

The properties of aerosols are of paramount importance in atmospheric chemistry and human health. The hydrogen bond network of glycerol-water aerosols generated from an aqueous solution with different mixing ratios is probed directly with X-ray photoelectron spectroscopy. The carbon and oxygen X-ray spectra reveal contributions from gas and condensed phase components of the aerosol. It is shown that water suppresses glycerol evaporation up to a critical mixing ratio. A dielectric analysis using terahertz spectroscopy coupled with infrared spectroscopy of the bulk solutions provides a picture of the microscopic heterogeneity prevalent in the hydrogen bond network when combined with the photoelectron spectroscopy analysis. The hydrogen bond network is composed of three intertwined regions. At low concentrations, glycerol molecules are surrounded by water forming a solvated water network. Adding more glycerol leads to a confined water network, maximizing at 22 mol %, beyond which the aerosol resembles bulk glycerol. This microscopic view of hydrogen bonding networks holds promise in probing evaporation, diffusion dynamics, and reactivity in aqueous aerosols.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

How the Hydrophobic Interface between a Perfluorosulfonic Acid Polymer and Water Vapor Controls Membrane Hydration

Stable hydration in perfluorinated polyelectrolyte membranes such as Nafion is essential to maintain good ion conductivity and manage permeation, especially in vapor-fed devices where water content depends on relative humidity in a gas stream. Extensive studies in the literature have shown that Nafion hydration in water vapor is controlled by its interfacial transport resistance. Nafion forms a fluorine-rich layer at the polymer-gas interface, and it has been proposed that this layer blocks water transport due to its hydrophobicity. To develop a molecular-level description of the physics underlying transport resistance in this system, we have performed a computational reaction-diffusion kinetics study of water evaporation from Nafion. Two distinct models are examined, one mimicking the blocking function proposed in the literature and the other assuming that there is no blocking, treating instead water evaporation as a dynamic balance between uptake from the gas and desorption from the polymer surface. Simulation results are compared to time-dependent infrared data over a range of 100-0% relative humidity from the literature. Only the dynamic model successfully reproduces experimental observations. This indicates that the physical nature of interfacial transport resistance is not slow diffusion across an interfacial layer; rather, it is due to the competition between dehydration and rehydration. The simulation data provide details on the accompanying water distributions throughout the membrane and on interfacial kinetics, showing that they are characterized by strong fluctuations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗