Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “electron beams”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Electron beams and associated rapid fluctuations in solar flares

Recent observations show that the rapid fluctuations in radio, hard X-ray, and H-alpha emissions are closely associated with type III and microwave (or decimetric) bursts during the impulsive and/or preimpulsive phases of solar flares. In order to clarify the physical processes of these observed phenomena, this paper proposes a tentative model of two acceleration regions A (source of type III bursts) and B (source of microwave or decimetric bursts) formed in the neutral sheet and at the top of a flaring loop, respectively; and also suggests that the electron beams streaming from region A and/or region B downward to the chromosphere are responsible for the rapid fluctuations in the different emissions mentioned above during the impulsive and/or preimpulsive phases of solar flares.

Li, C. S.↗
NASA NTRS2017

The Atmospheric Response to High Nonthermal Electron Beam Fluxes in Solar Flares. I. Modeling the Brightest NUV Footpoints in the X1 Solar Flare of 2014 March 29

The 2014 March 29 X1 solar flare (SOL20140329T17:48) produced bright continuum emission in the far- and near-ultraviolet (NUV) and highly asymmetric chromospheric emission lines, providing long-sought constraints on the heating mechanisms of the lower atmosphere in solar flares. We analyze the continuum and emission line data from the Interface Region Imaging Spectrograph (IRIS) of the brightest flaring magnetic footpoints in this flare. We compare the NUV spectra of the brightest pixels to new radiative-hydrodynamic predictions calculated with the RADYN code using constraints on a nonthermal electron beam inferred from the collisional thick-target modeling of hard X-ray data from Reuven Ramaty High Energy Solar Spectroscopic Imager. We show that the atmospheric response to a high beam flux density satisfactorily achieves the observed continuum brightness in the NUV. The NUV continuum emission in this flare is consistent with hydrogen (Balmer) recombination radiation that originates from low optical depth in a dense chromospheric condensation and from the stationary beam-heated layers just below the condensation. A model producing two flaring regions (a condensation and stationary layers) in the lower atmosphere is also consistent with the asymmetric Fe II chromospheric emission line profiles observed in the impulsive phase.

Kowalski, Adam F.↗
NASA NTRS2014

Electron Beam Freeform Fabrication of Titanium Alloy Gradient Structures

Historically, the structural optimization of aerospace components has been done through geometric methods. A monolithic material is chosen based on the best compromise between the competing design limiting criteria. Then the structure is geometrically optimized to give the best overall performance using the single material chosen. Functionally graded materials offer the potential to further improve structural efficiency by allowing the material composition and/or microstructural features to spatially vary within a single structure. Thus, local properties could be tailored to the local design limiting criteria. Additive manufacturing techniques enable the fabrication of such graded materials and structures. This paper presents the results of a graded material study using two titanium alloys processed using electron beam freeform fabrication, an additive manufacturing process. The results show that the two alloys uniformly mix at various ratios and the resultant static tensile properties of the mixed alloys behave according to rule-of-mixtures. Additionally, the crack growth behavior across an abrupt change from one alloy to the other shows no discontinuity and the crack smoothly transitions from one crack growth regime into another.

Brice, Craig A.↗
NASA NTRS2019

Electron Beam Welding of Pure Tungsten Hex Cans for Nuclear Thermal Propulsion Engines

Nuclear thermal propulsion (NTP) is an in-space propulsion method currently being developed at the NASA Marshall Space Flight Center (MSFC). NTP systems are a high specific impulse (750–1,100 s), high thrust (15,000–250,000 lbf ) method of propulsion which have the potential to allow for faster transit times when optimizing for high ΔV. In the nuclear rocket engine, the heat from the nuclear fission reaction is transferred to a low molecular mass propellant (such as hydrogen). Hot propellant is expanded through a nozzle to generate thrust. Development of ceramic metal (cermet) fuel systems for NTP applications is currently ongoing at MSFC. In cermet fuel systems, ceramic fissile fuel particles such as uranium nitride or uranium dioxide are dispersed within a net-shaped, high-density structural matrix. The composite material is cladded by a protective metal structure to make up an NTP fuel element. Cladding materials must be able to withstand the demanding operating conditions required of the engine as well as retain a hermetic seal to allow for retention of fuel element structural integrity, prevent hydrogen attack or migration of the ceramic fuel, and limit release of fission products during operation. For NTP applications, tungsten is a prime material for both the metal matrix and cladding in cermet fuel systems because of its high melting point, high temperature strength, and compatibility with hot hydrogen. If a weld in tungsten with the capability of holding a hermetic seal is achievable, tungsten becomes a strong candidate for NTP applications. This Technical Memorandum focuses on determining the weldability of pure tungsten using electron beam welding (EBW). Tungsten appears well suited for NTP applications, but it has a high ductile to brittle transition temperature (DBTT) dependent upon chemical composition, structure/stress distribution, and mechanical conditions. Therefore, it is highly subject to brittle fracture. Because of its high susceptibility to brittle fracture, it is very difficult to weld. EBW was chosen for joining pure tungsten because of its low heat input compared to gas tungsten arc welding. Reduced heat input can be directly correlated with an increase in ductility of a tungsten weld. EBW is a high energy density welding process in which a stream of electrons penetrates a weld joint in a deep, narrow spike in contrast to a broad gas tungsten arc weld pool. The investigation initially focused on EBW of tungsten plates of both 0.01 in and 0.03 in thickness to determine if EBW could weld pure tungsten without the presence of visual defects—particularly cracking—in the welds. Variation in the weld procedure and post-weld heat treatment (PWHT) was used to improve the surface appearance of flat EBWs on a pure tungsten sheet. The investigation moved on to weld 0.05-in-thick hexagonal tungsten cans with a weld joint thickness of 0.025 in. The goal for welding the pure tungsten hex cans was to avoid any visual surface defects and generate a weld capable of a hermetic seal. This proved difficult. Cold welds commonly exhibited porosity that leaked air. Hot welds exhibited cracks, typically observed immediately after welding. Later welds were preheated to increase ductility and decrease the likelihood of through-thickness cracking. PWHT was used to arrest microcrack growth both in the flat weld samples and hexagonal weld samples.

Courtright, Z. S.↗
NASA NTRS1974

Observations of radiation from an electron beam artificially injected into the ionosphere

This paper reports the observations of waves generated by a controlled beam of particles artificially injected into the ionosphere and magnetosphere. The measurements were made during the Electron Echo 1 experiment, in which an electron accelerator was carried to a height of 350 km in the ionosphere from Wallops Island, Virginia, on an Aerobee 350 sounding rocket. It injected into the earth's magnetic field over 3000 16-ms pulses of electrons with 40-keV energy and a current of 70 mA at pitch angles between 70 and 110 deg. The ejected fiber glass nose cone carried antennas and receivers to measure the electric field of waves generated by the beam. Associated with the electron beam was radiation detected at frequencies near the electron plasma frequency of the background ionosphere, near twice the electron cyclotron frequency in the whistler mode, and near zero frequency. Associated with the operation of an argon plasma generator used to keep the accelerator neutralized were continuous emissions detected at frequencies near the lower-hybrid resonance (LHR).

Cartwright, D. G.↗
NASA NTRS1967

Electron beam parallel X-ray generator

Broad X ray source produces a highly collimated beam of low energy X rays - a beam with 2 to 5 arc minutes of divergence at energies between 1 and 6 keV in less than 5 feet. The X ray beam is generated by electron bombardment of a target from a large area electron gun.

Payne, P.↗
NASA NTRS1987

Electron beam experiments at high altitudes

Experiments with the electron gun on the SCATHA satellite produced evidence of beam-plasma interactions, and heating of the low energy electrons around the satellite. These experiments were conducted near geosynchronous orbit, in the dusk bulge, and plasma sheet, with one short operation in the lobe regions, providing a range of ambient plasma densities. The electron gun was operated at 50 eV, with beam currents of 1, 10, and 100 micro-A. Data from electrostatic analyzers and the dc electric field experiment show that the satellite charged to near the beam energy in sunlight, if the beam current was sufficient. Higher ambient densities required higher beam currents. The electrostatic analyzers showed distribution functions which had peaks, or plateaus, at energies greater than the satellite potential. These measurements indicate heating of the ambient plasma at several Debye lengths from the satellite, with the heated plasma then accelerated into the satellite. It is likely that the ambient plasma is in fact the photoelectron sheath generated by the satellite.

Olsen, R. C.↗
NASA NTRS1988

Electron beam experiments at high altitudes

Experiments with the electron gun on the SCATHA satellite produced evidence of beam-plasma interactions, and heating of the low energy electrons around the satellite. These experiments were conducted near geosynchronous orbit, in the dusk bulge, and plasma sheet, with one short operation in the lobe regions, providing a range of ambient plasma densities. The electron gun was operated at 50 eV, with beam currents of 1, 10, and 100 micro-A. Data from electrostatic analyzers and the DC electric field experiment show that the satellite charged to near the beam energy in sunlight, if the beam current was sufficient. Higher ambient densities required higher beam currents. The electrostatic analyzers showed distribution functions which had peaks, or plateaus, at energies greater than the satellite potential. These measurements indicate heating of the ambient plasma at several Debye lengths from the satellite, with the heated plasma then accelerated into the satellite. It is likely that the ambient plasma is in fact the photoelectron sheath generated by the satellite.

Olsen, R. C.↗
NASA NTRS1984

Observations of electron beams in the low-latitude boundary layer

ISEE 1 electron spectrometer observations are used to study the electron distribution function in the low latitude boundary layer (LLBL) of the magnetosphere in the sunward direction. The study included 43 examples of well-defined layers. Using three-dimensional, model-independent distribution functions of electrons observed in the boundary layer, beams of field-aligned electrons with typically 100 eV energy maximums, streaming in either one, or both, directions have been identified. The phase densities in the LLBL and at lower altitudes are similar, and the beams observed in the LLBL are identified with those observed at lower altitudes. They form an important component of the plasma electrons in the LLBL, which otherwise resembles a mixture of magnetosheath-like and magnetospheric electrons.

Ogilvie, K. W.↗
NASA NTRS1990

The electron beam instability and turbulence theories

Extensions and practical applications of recent observations of electron beam-plasma interactions are investigated for the range of turbulence theories, extending from quasi-linear to strong turbulence theory, which have been developed on the basis of the Langmuir-wave excitation model. Electron foreshock observations have indicated that linear instability theory must encompass the excitation of waves whose frequencies are substantially different from those of the plasma frequency; the point of departure for such extensions should be a quantitative test of existing theories, and particle simulations conducive to such testing are presented. A step-by-step addition of physical considerations is used in such simulation studies to differentiate among nonlinear turbulence effects.

Dum, C. T.↗
NASA NTRS1987

Generation of plasma waves by thick-target electron beams, and the expected radiation signature

The production of plasma waves by a nonthermal beam of high-energy electrons injected into a background thermal plasma was investigated. The coupled kinetic equations for nonthermal electrons were solved, and the level of the plasma waves produced by the bump-on-tail instability arising as a result of the Coulomb collisions of nonthermal electrons with background plasma was estimated. In addition, the radiation signatures of these waves were examined. It is shown that the wave-particle interactions have a significant effect on the overall distribution of the electrons and that it is unlikely that such effects can be discerned in the observed bremsstrahlung or synchrotron radiation of the nonthermal electrons. However, a significant fraction of the energy lost by the beam is transferred to plasma waves and is then dissipated by the thermal plasma.

Hamilton, Russell J.↗
NASA NTRS1986

Simulations of electron beam excited modes in the high-altitude magnetosphere

Excitation of waves by electron distributions consisting of hot, beam, and cold populations is investigated theoretically and with the help of particle simulations. The main modes excited include the upper hybrid oscillation for nearly perpendicular propagation; the whistler mode at oblique angles, which becomes the plasma two-stream oscillation for parallel propagation; and the electron acoustic mode for nearly parallel propagation. The whistler mode, excited by thermal fluctuation enhancement, has a broad range of wave numbers and quasi-linearly decreases the beam slope, while the electron acoustic mode, which is linearly unstable, has a narrow spread in phase velocities and traps the beam and the warm electrons forming a double humped distribution. Both modes contribute to forming a tail in the cold electron distribution. The resulting wave spectrum is discussed in the context of DE 1 observations.

Roth, I.↗
NASA NTRS1980

Power distribution for electron beam welding

The power distribution of an electron seam is analyzed. Digital computer techniques are used to evaluate the radial distribution of power detected by a wire probe circulating through the beam. Results are reported.

Edwards, E.↗
NASA NTRS1985

The energization of electrons and ions by electron beams injected in the ionosphere

This paper represents a continuation of an investigation of the nature and origin of the particle populations associated with an electron beam-emitting rocket experiment in the ionosphere. In this investigation, the intense flux of suprathermal electrons created around such a rocket has been studied by several groups. Arnoldy and Winckler (1981) have discussed the vehicle floating potential problem. The present paper is concerned with results which have been obtained from the Echo 4 and 5 experiments considered by Swanson (1983). Attention is given to instrumentation, suprathermal electrons, thermal ions, energetic ions, and ion resonances.

Arnoldy, R. L.↗
NASA NTRS1975

Performance of 75-millimeter-bore bearings using electron-beam-welded hollow balls with a diameter ratio of 1.26

An experimental investigation was performed to determine the rolling element fatigue life of electron beam-welded hollow balls with a diameter ratio (o.d./i.d.) of 1.26 and to determine the operating characteristics of bearings using these hollow balls. Similar bearings with solid balls were also tested and the data compared. The bearings were operated at shaft speeds up to 28,000 rpm with a thrust load of 2200 N (500 lb). Ball failures during the bearing tests were due to flexure fatigue. The solid and hollow ball bearings tested showed little difference in outer race temperatures and indicated the same bearing torque. The 17.5-mm (0.6875-in.) diameter balls were also tested in the five-ball fatigue tester and showed no significant difference in life when compared with the life of a solid ball.

Coe, H. H.↗
NASA NTRS1991

Electron beam sounding rocket experiments for probing the distant magnetosphere

Electron accelerators on sounding rockets have injected 8-40-keV electrons on closed magnetospheric tail field lines near 250 km altitude in the northern auroral zone. These beams mirrored at the southern conjugate point ad returned as 'echoes' which were detected on the rocket system. The 20 percent of the beam that returned was sufficient to measure field line lengths and verify magnetospheric magnetic models, to measure fluctuating electric fields, and electron pitch angle scattering (6-10) R(E) distant, and to identify 10-100 V field-aligned potentials above the rocket. The experiment gives new insight into the motion of natural electrons in the outer Van Allen radiation belt.

Nemzek, R. J.↗