Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “elastic materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Plane-stress fracture of compact and notch-bend specimens

Thin-gaged or high toughness materials containing cracks usually fail in a ductile manner with nominal failure stresses approaching the ultimate strength of the material. For such materials, a two-parameter fracture criterion was developed. An equation which related the linear elastic stress-intensity factor, elastic nominal stress, and two material parameters has previously been derived and has been used as a fracture criterion for surface- and through-cracked specimens under tensile loading. In the present paper the two-parameter fracture criterion was rederived in a more general form and was extended to compact and notch-bend fracture specimens. A close correlation was found between experimental and calculated failure stresses.

Newman, J. C., Jr.↗
NASA NTRS1986

Thermally induced stresses in cross-ply composite tubes

An approximate solution for determining stresses in cross-ply composite tubes subjected to a circumferential temperature gradient is presented. The solution is based on the principle of complementary virtual work (PCVW) in conjunction with a Ritz approximation on the stress field and accounts for the temperature dependence of material properties. The PCVW method is compared with a planar elasticity solution using temperature-independent material properties and a Navier approach. The net effect of including temperature-dependent material properties is that the peak absolute values of the stresses are reduced. The dependence of the stresses on the circumferential location is also reduced in comparison with the case of temperature-independent properties.

Hyer, M. W.↗
NASA NTRS1991

Mechanical behavior of a continuous fiber reinforced aluminum matrix composite subjected to transverse and thermal loading

The transverse properties of an aluminum alloy metal matrix composite reinforced by continuous alumina fibers were investigated. The composite is subjected to both mechanical and cyclic thermal loading. The results of an experimental program indicate that the shakedown concept of structural mechanics provides a means of describing the material behavior. When the loading conditions are within the shakedown region, the material finally responds in an elastic manner after initial plastic response, and for loading conditions outside the shakedown region, the material exhibits a rapid incremental plastic strain accumulation. The failure strain varies by an order of magnitude according to the operating conditions. Hence, for high mechanical and low thermal loading, the failure strains is small; for low mechanical and high thermal loading, the failure strain is large.

Jansson, S.↗
NASA NTRS2006

Properties of a Ni(sub 19.5)Pd(sub 30)Ti(sub 50.5) high-temperature shape memory alloy in tension and compression

Potential applications involving high-temperature shape memory alloys have been growing in recent years. Even in those cases where promising new alloys have been identified, the knowledge base for such materials contains gaps crucial to their maturation and implementation in actuator and other applications. We begin to address this issue by characterizing the mechanical behavior of a Ni19.5Pd30Ti50.5 high-temperature shape memory alloy in both uniaxial tension and compression at various temperatures. Differences in the isothermal uniaxial deformation behavior were most notable at test temperatures below the martensite finish temperature. The elastic modulus of the material was very dependent on strain level; therefore, dynamic Young#s Modulus was determined as a function of temperature by an impulse excitation technique. More importantly, the performance of a thermally activated actuator material is dependent on the work output of the alloy. Consequently, the strain-temperature response of the Ni19.5Pd30Ti50.5 alloy under various loads was determined in both tension and compression and the specific work output calculated and compared in both loading conditions. It was found that the transformation strain and thus, the specific work output were similar regardless of the loading condition. Also, in both tension and compression, the strain-temperature loops determined under constant load conditions did not close due to the fact that the transformation strain during cooling was always larger than the transformation strain during heating. This was apparently the result of permanent plastic deformation of the martensite phase with each cycle. Consequently, before this alloy can be used under cyclic actuation conditions, modification of the microstructure or composition would be required to increase the resistance of the alloy to plastic deformation by slip.

Noebe, Ronald↗
DOE OSTI2021

The Water-Fe-Pressure dependent single-crystal elastic properties of wadsleyite: Implications for the seismic anisotropy in the upper Mantle Transition Zone

Recent seismic studies suggest an anisotropic Mantle Transition Zone (MTZ) in areas adjacent to subducted slabs. Wadsleyite is the main anisotropy contributor in the upper MTZ, therefore the interpretation of these seismic observations requires the knowledge of single-crystal elastic moduli (C ij s) and the deformation-induced lattice preferred orientation (LPO) of wadsleyite. Wadsleyite can host up to 3 wt% water in its crystal structure as point defects in the form of hydroxyl groups, however, the combined effect of water content, Fe content, and pressure on the C ij s of wadsleyite remains unclear. In this study, we measured the high-pressure single-crystal elasticity of a synthetic hydrous Fe-bearing wadsleyite (0.14(5) wt% water, Fe#=9.4, Fe 3+ /ΣFe=0.3) up to 18.2 (2) GPa. In combination with previous experimental data, we separated the effects of pressure, water, and Fe contents on the Cijs and intrinsic elastic anisotropy of wadsleyite. Overall, our results suggest that the intrinsic elastic anisotropy of wadsleyite decreases with pressure, water, and Fe contents. At 15 GPa, increasing the water content by 0.1 wt% or Fe# by 1 decreases the V P and V S anisotropy of wadsleyite by ~1.1-1.3%, and ~0.8-1.3% in average, respectively. Combined with the LPO determined in previous deformation experiments, we modeled the seismic anisotropy in the upper MTZ generated by a sub-vertical mantle flow near cold subducted slabs and a sub-horizontal mantle flow in the ambient mantle. In both scenarios, the LPO of wadsleyite leads to V SV (vertically polarized shear wave velocity) > V SH (horizontally polarized shear wave velocity). Our results suggest that wadsleyite may account for a weak anisotropic MTZ (<1%) on the global scale. Considering the fact that water decreases the elastic anisotropy but promotes LPO of wadsleyite, seismic anisotropy may not be a good water sensor.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Unconventional pressure-induced magnetic transitions and mechanical properties in non-magnetic LaFeSi

Here, this work demonstrates that two consecutive magnetic transitions occur in non-magnetic LaFeSi compound under negative hydrostatic pressure (small volume expansion). Electronic structure properties of LaFeSi were calculated using density functional theory (DFT) to understand the origin of these magnetic transitions. Mechanical properties of LaFeSi, especially elastic properties (shear and Young’s modulus, and Poisson’s ratio), were determined by DFT distortion calculations to elucidate lattice anisotropy and stability. The antiferromagnetic transition at –7.52 GPa, predicted in our work for LaFeSi, is consistent with the reported experimentally observed antiferromagnetic ground states in CeMnSi and LaMnSi compounds having similar crystal geometry. This finding of unexpected magnetic ordering predicts that layered non-magnetic materials, like LaFeSi, may become magnetically active with lattice expansion.

36 MATERIALS SCIENCE↗
NASA NTRSDate not supplied

Computational Study of Oxidative Etch Pitting in FiberForm and the Effect on Its Material Properties

Erosion of carbon due to oxidation does not occur uniformly but through the formation of localized etch pits because of active surface sites. These active sites are formed due to the presence of atomic defects on the carbon surface, and have much higher reactivity compared to average non-defective sites. Thus, these active sites are first to react during ablation, resulting in their removal. This causes all the neighboring atoms to be defective and increase their reactivity, thus leading to the localized carbon removal around these “active” sites. In this manner, these highly reactive defective sites serve as nucleation sites for the formation and growth of etch pits with potentially detrimental effects on the structural integrity. In order to understand the influence of these etch pits on the material properties of carbon fiber microstructures, we have developed a new capability within direct simulation Monte Carlo (DSMC) to capture the etch pit formation process. This capability is developed within the DSMC code SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) and can model the material removal in presence of active sites leading to the formation of etch pits. The focus of the current work will be to study the effect of etch pits on the material properties of FiberForm, a commonly used base material within many thermal protection system materials (TPS). The microstructure of virgin FiberForm obtained directly from X-ray microtomography experiments is used within SPARTA to obtain the ablated geometries with etch pits. These pitted microstructures are then imported within the Porous Microstructure Analysis (PuMA) software and various material properties such as elasticity, thermal conductivity, and permeability are computed. The variation of these properties as a result of the complex evolution of the surface topology due to etch pit formation is studied and analyzed. Furthermore, the effect of pitting is compared to the case of shrinking fibers, which has been the standard for modelling ablation of carbon structures; and significant differences are observed. Thus, such a physically realistic modeling of material removal through the formation of etch pits will be helpful in predicting the degradation of carbon-based TPS more accurately during oxidation; as well as other mechanisms such as spallation, which involves the removal of chunks of material into the flow due to etch pit growth. This will ultimately improve our understanding of the failure modes in these materials due to ablation.

Carbon Ablators↗
NASA NTRSDate not supplied

Computational Study of Oxidative Etch Pitting in FiberForm and the Effect on Its Material Properties

Erosion of carbon due to oxidation does not occur uniformly but through the formation of localized etch pits because of active surface sites. These active sites are formed due to the presence of atomic defects on the carbon surface, and have much higher reactivity compared to average non-defective sites. Thus, these active sites are first to react during ablation, resulting in their removal. This causes all the neighboring atoms to be defective and increase their reactivity, thus leading to the localized carbon removal around these “active” sites. In this manner, these highly reactive defective sites serve as nucleation sites for the formation and growth of etch pits with potentially detrimental effects on the structural integrity. In order to understand the influence of these etch pits on the material properties of carbon fiber microstructures, we have developed a new capability within direct simulation Monte Carlo (DSMC) to capture the etch pit formation process. This capability is developed within the DSMC code SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) and can model the material removal in presence of active sites leading to the formation of etch pits. The focus of the current work will be to study the effect of etch pits on the material properties of FiberForm, a commonly used base material within many thermal protection system materials (TPS). The microstructure of virgin FiberForm obtained directly from X-ray microtomography experiments is used within SPARTA to obtain the ablated geometries with etch pits. These pitted microstructures are then imported within the Porous Microstructure Analysis (PuMA) software and various material properties such as elasticity, thermal conductivity, and permeability are computed. The variation of these properties as a result of the complex evolution of the surface topology due to etch pit formation is studied and analyzed. Furthermore, the effect of pitting is compared to the case of shrinking fibers, which has been the standard for modelling ablation of carbon structures; and significant differences are observed. Thus, such a physically realistic modeling of material removal through the formation of etch pits will be helpful in predicting the degradation of carbon-based TPS more accurately during oxidation; as well as other mechanisms such as spallation, which involves the removal of chunks of material into the flow due to etch pit growth. This will ultimately improve our understanding of the failure modes in these materials due to ablation.

Carbon Ablators↗
DOE OSTI2023

Probing the Mechanical Properties of 2D Materials via Atomic‐Force‐Microscopy‐Based Modulated Nanoindentation

Abstract As the field of low‐dimensional materials (1D or 2D) grows and more complex and intriguing structures are continuing to be found, there is an emerging need for techniques to characterize the nanoscale mechanical properties of all kinds of 1D/2D materials, in particular in their most practical state: sitting on an underlying substrate. While traditional nanoindentation techniques cannot accurately determine the transverse Young's modulus at the necessary scale without large indentations depths and effects to and from the substrate, herein an atomic‐force‐microscopy‐based modulated nanomechanical measurement technique with Angstrom‐level resolution (MoNI/ÅI) is presented. This technique enables non‐destructive measurements of the out‐of‐plane elasticity of ultra‐thin materials with resolution sufficient to eliminate any contributions from the substrate. This method is used to elucidate the multi‐layer stiffness dependence of graphene deposited via chemical vapor deposition and discover a peak transverse modulus in two‐layer graphene. While MoNI/ÅI has been used toward great findings in the recent past, here all aspects of the implementation of the technique as well as the unique challenges in performing measurements at such small resolutions are encompassed.

2D materials↗
DOE OSTI2022

The effect of elastic anisotropy on the symmetry selection of irradiation-induced void superlattices in cubic metals

We report self-organized microstructures and patterns have been widely observed in non-equilibrium physical systems. In particular, irradiation in metals creates far-from-equilibrium environments, in which the competing dynamics of defect production and annihilation can lead to unique self-organized superlattice structures, e.g., void and gas bubble superlattices. From a physical point of view, the superlattice structures are dictated by the intrinsic symmetry breaking in the metals, i.e., anisotropy caused by the breaking of continuous rotational symmetry. In the literature, two distinctive anisotropies, elastic anisotropy and diffusion anisotropy of interstitials, have been proposed to be the origins of superlattice formation. However, it is still unclear which anisotropy dominates the symmetry selection of superlattice structures. In this paper, we study elastic anisotropy and its effect on the symmetry of void superlattices. By using theoretical analyses and phase field simulations, we show that elastic anisotropy in cubic metals can lead to either face-centered cubic or simple cubic superlattices depending on the Zener anisotropy ratio. The superlattices formed under this elastic anisotropy mechanism must form under the influence of spinodal decomposition, as the mechanism requires perturbations in the vacancy concentration field to develop into spatially-static concentration waves. We compare to existing work on symmetry selection in superlattices via diffusion anisotropy and to experimental observations, and we suggest that concentration wave development under the influence of elastic anisotropy is not the mechanism for symmetry selection during the formation of irradiation-induced void superlattices, but that diffusion anisotropy could be the dominant mechanism.

36 MATERIALS SCIENCE↗
NASA NTRS1990

Stress Dependence of Ultrasonic Velocity in Unidirectional Graphite/Epoxy Composites for Longitudinal Waves Propagating Along the Direction of Stress

The first measurements of the stress induced velocity changes for propagation directions along the direction of applied stress in gr/ep composites have been presented. For propagation and stress direction perpendicular to the fiber direction, the data demonstrated a linear relation between normalized velocity shift and stress. After corrections for the delay line were made, the slope or SAC was determined and compared favorably with the expected value calculated from the previously determined nonlinear coefficients of this material. The ratio of the SAC to the elastic compliance for this direction of loading was evaluated and found to have a value similar to numerous other materials which have very different linear elastic properties. Measurements with stress and propagation along the fibers yielded unusual behavior. The curves were very nonlinear and even shifted direction at higher loads. The large scatter in the data due to bond variations made separation of material effects from bond induced artifacts impossible. Thus the SAC, R, and the remaining two unknown TOEC's could not be determined for this direction of propagation. These measurements further expand the basis of determining nonlinear elastic properties of composite materials. These properties may be useful in developing much needed NDE techniques to determine such important parameters as residual stress after cure and residual strength after impact damage. Additional study is needed to measure the nonlinear behavior in other composite materials including angle ply laminates. Also, other techniques to measure elastic nonlinearity such as harmonic generation should be applied to composites to improve the understanding of these properties and their importance.

Prosser, William H.↗
DOE OSTI2021

Preferred orientation of calcium aluminosilicate hydrate compacts: Implications for creep and indentation

Nano/micro-indentation has been extensively used to examine elastic properties and creep of cement-based materials. However, there have been inconsistencies in the measured elastic moduli and debate on the creep mechanism of calcium (alumino) silicate hydrates (C-(A-)S-H). To bring new insights, we examined the deviatoric stress-induced preferred orientation of calcium aluminosilicate hydrate (C-A-S-H), portlandite, and ettringite compacts, using synchrotron-based X-ray diffraction. Intense preferred orientations were observed in C-A-S-H compacts, and the c-axis of unit cells is highly aligned with the compression direction; weaker c-axis related fiber-type texture formed in portlandite and ettringite. Higher humidity, greater compacting pressure, and/or increased duration of the pressure intensified the C-A-S-H preferred orientation, which is facilitated by gel-pore water lubrication. This pressure-induced time-dependent preferential re-orientation of crystallites can contribute to the creep of cement-based materials, and it may cause overrepresentation of the soft c-axis of C-(A-)S-H unit-cell in nanoindentation experiments and underestimation of Young's modulus.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Measurement of the Static Nonlinear Third-Order Elastic Moduli of Rocks: Problems and Applicability

The third-order elastic (TOE) model has been used to describe the widely observed nonlinear mechanical behaviors of earth materials. In addition to linear elastic constants ( λ , μ ), three nonlinear elastic moduli ( A , B , C ) are required for isotropic rocks. Contrary to previous research on dynamic TOE moduli, this study followed the protocol to measure strain and stress under uniaxial and hydrostatic compressive tests statically, which were later used to invert for the full set of TOE moduli for four standard rock types with differing pore structures of a porous oolitic limestone, quartz-rich sandstones, and a dense crystalline basalt. The applicability of the TOE model to characterize nonlinearity depends on the fulfillment of path-independence and small-strain assumptions. Using the measured static TOE moduli, the finite element model demonstrates that the stress in the vicinity of the wellbore is more amplified than the stress in the linear elastic case, which leads to a wider zone of rock failure around the wellbore. Due to the long-standing discrepancy between static and dynamic moduli, the rarely reported full set of static TOE moduli is necessary and will benefit future research in understanding the effect of rock nonlinearity on geophysical and geomechanical applications, such as long-term safe storage of CO 2 and generating process of geohazards.

58 GEOSCIENCES↗
NASA NTRS2015

Comparison of Models for Ball Bearing Dynamic Capacity and Life

Generalized formulations for dynamic capacity and life of ball bearings, based on the models introduced by Lundberg and Palmgren and Zaretsky, have been developed and implemented in the bearing dynamics computer code, ADORE. Unlike the original Lundberg-Palmgren dynamic capacity equation, where the elastic properties are part of the life constant, the generalized formulations permit variation of elastic properties of the interacting materials. The newly updated Lundberg-Palmgren model allows prediction of life as a function of elastic properties. For elastic properties similar to those of AISI 52100 bearing steel, both the original and updated Lundberg-Palmgren models provide identical results. A comparison between the Lundberg-Palmgren and the Zaretsky models shows that at relatively light loads the Zaretsky model predicts a much higher life than the Lundberg-Palmgren model. As the load increases, the Zaretsky model provides a much faster drop off in life. This is because the Zaretsky model is much more sensitive to load than the Lundberg-Palmgren model. The generalized implementation where all model parameters can be varied provides an effective tool for future model validation and enhancement in bearing life prediction capabilities.

Rolling-element Fatigue↗
NASA NTRS1976

Fracture analysis of various cracked configurations in sheet and plate materials

A two-parameter fracture criterion has been derived which relates the linear-elastic stress-intensity factor at failure, the elastic nominal failure stress, and two material parameters. The fracture criterion was applied to center-crack tension, compact, and notch-bend fracture specimens made of steel, titanium, or aluminum alloy materials tested at room temperature. The fracture data included a wide range of crack lengths, specimen widths, and thicknesses. The materials analyzed had a wide range of tensile properties. Failure stresses calculated using the criterion agreed well (plus or minus 10 percent) with experimental failure stresses. The criterion was also found to correlate fracture data from different specimen types (such as center-crack tension and compact specimens), within plus or minus 10 percent for the same material, thickness, and test temperature.

Newman, J. C., Jr.↗
NASA NTRS2006

Multifunctional Characteristics of Carbon Nanotube (CNT) Yarn Composites

By forming composite structures with Carbon Nanotube (CNT) yarns we achieve materials capable of measuring strain and composite structures with increased mechanical strength. The CNT yarns used are of the 2-ply and 4-ply variety with the yarns having diameters of about 15-30 micrometers. The strain sensing characteristics of the yarns are investigated on test beams with the yarns arranged in a bridge configuration. Additionally, the strain sensing properties are also investigated on yarns embedded on the surface of a flexible membrane. Initial mechanical strength tests also show an increase in the modulus of elasticity of the composite materials while incurring a weight penalty of less than one-percent. Also presented are initial temperature characterizations of the yarns.

Hernandez, Corey D.↗
DOE OSTI2022

High temperature ceramic thermal insulation material

Flexible and lightweight thermal insulation materials with hierarchical microstructures are ubiquitous in thermal management and protection systems. Ceramic aerogels promise high-temperature thermal insulation but lack mechanical robustness, while the fibrous materials with excellent mechanical elasticity display modest thermal insulation. Here we describe flexible hierarchical superhydrophobic ceramic insulation nanocomposites through the densified architectured hierarchical nanostructures, radiative insulation coating, and interfacial cross-linking among composites. The lightweight flexible ceramic nanocomposites exhibit a density of 0.13 g/cm 3 , high-temperature fire resistance with thermal conductivity of 0.024 W/(m·K), and super-hydrophobicity with the water contact angle of 152°. The mechanical robustness and high-temperature thermal insulation of ceramic nanocomposites, together with its soundproof performance, shed light on the low-cost flexible insulation materials manufacturing with scalability for high-temperature thermal insulation applications under high mechanical loading conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Elastic Lattice Enabling Reversible Tetrahedral Li Storage Sites in a High-Capacity Manganese Oxide Cathode

The key to breaking through the capacity limitation imposed by intercalation chemistry lies in the ability to harness more active sites that can reversibly accommodate more ions (e.g., Li + ) and electrons within a finite space. However, excessive Li-ion insertion into the Li layer of layered cathodes results in fast performance decay due to the huge lattice change and irreversible phase transformation. Here, in this study, an ultrahigh reversible capacity is demonstrated by a layered oxide cathode purely based on manganese. Through a wealth of characterizations, it is clarified that the presence of low-content Li 2 MnO 3 domains not only reduces the amount of irreversible O loss; but also regulates Mn migration in LiMnO 2 domains, enabling elastic lattice with high reversibility for tetrahedral sites Li-ion storage in Li layers. This work utilizes bulk cation disorder to create stable Li-ion-storage tetrahedral sites and an elastic lattice for layered materials, with a reversible capacity of 600 mA h g –1 , demonstrated in th range 0.6–4.9 V versus Li/Li + at 10 mA g –1 . Admittedly, discharging to 0.6 V might be too low for practical use, but this exploration is still of great importance as it conceptually demonstrates the limit of Li-ions insertion into layered oxide materials.

25 ENERGY STORAGE↗