Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “data dependencies”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

A proven approach for more effective software development and maintenance

Modern space flight mission operations and associated ground data systems are increasingly dependent upon reliable, quality software. Critical functions such as command load preparation, health and status monitoring, communications link scheduling and conflict resolution, and transparent gateway protocol conversion are routinely performed by software. Given budget constraints and the ever increasing capabilities of processor technology, the next generation of control centers and data systems will be even more dependent upon software across all aspects of performance. A key challenge now is to implement improved engineering, management, and assurance processes for the development and maintenance of that software; processes that cost less, yield higher quality products, and that self-correct for continual improvement evolution. The NASA Goddard Space Flight Center has a unique experience base that can be readily tapped to help solve the software challenge. Over the past eighteen years, the Software Engineering Laboratory within the code 500 Flight Dynamics Division has evolved a software development and maintenance methodology that accommodates the unique characteristics of an organization while optimizing and continually improving the organization's software capabilities. This methodology relies upon measurement, analysis, and feedback much analogous to that of control loop systems. It is an approach with a time-tested track record proven through repeated applications across a broad range of operational software development and maintenance projects. This paper describes the software improvement methodology employed by the Software Engineering Laboratory, and how it has been exploited within the Flight Dynamics Division with GSFC Code 500. Examples of specific improvement in the software itself and its processes are presented to illustrate the effectiveness of the methodology. Finally, the initial findings are given when this methodology was applied across the mission operations and ground data systems software domains throughout Code 500.

Pajerski, Rose↗
NASA NTRS2004

MGS MAG/ER Data Analysis Using a Time and Magnetic Field Dependent Electron Transport Model

The goal of that project was to examine certain details about the dayside electron environment at Mars as seen by the Mars Global Surveyor (MGS) magnetometer/electron reflectometer (MAG/ER) instrument. Specifically, we stated that we would use the Khazanov and Liemohn (K&L) kinetic electron transport model to analyze features in the observations. This code includes a non-uniform magnetic field and time-dependence in the result (different from most other models of this type). It was originally developed for electron motion along field lines in the Earth's magnetosphere (between conjugate ionospheres), and is thus quite appropriate for application to the Mars magnetic field scenario. Numerous code developments were implemented and the Mars version of the K&L model is fully operational. Initial results from this code have focused on the examination of MGS MAG/ER observations in the crustal field region when it is on the dayside. After several presentations at scientific meetings, this study culminated in a JGR publication last year.

Liemohn, Michael W.↗
NASA NTRS2018

Developing a Standard for Earth Observation Data Preservation Content - A Path to Future Usability

For datasets to be usable, many pieces of information in addition to the data themselves are essential. During the active parts of the lifecycle of dataset generating projects, the needed information is usually accessible through individuals familiar with the various aspects of the projects. However, the utility of datasets tends to outlive the lives of projects, by several decades in many cases. Thus it is essential to capture all the relevant information about the datasets, data, metadata and associate knowledge that is sufficient to read, understand, interpret and reuse the datasets, while the projects are still active. The capture and preservation should be such that the data are usable when no consultation is available from the original project participants. Identification of specific categories of content through an international standard is beneficial to the user communities of the future, so that projects involving Earth observations and generating data products can consistently plan for preservation and future usability of the project outcomes. While there are existing standards that address archival and preservation in general, there are no existing international standards or specifications today to address what content should be preserved. The standard, ISO 19165-1, titled "Geographic Information - Preservation of digital data and metadata Part 1: Fundamentals" considers geographic information preservation in general. It acknowledges that "specific content items needed to preserve the full provenance and context of the data and associated metadata depend on the needs of the designated community and types of datasets (e.g., maps, remotely sensed data from satellites and airborne instruments, physical samples). Follow-up parts to this standard may be developed detailing content items appropriate to individual disciplines." NASA proposed an extension to this standard, titled "Geographic information -- Preservation of digital data and metadata -- Part 2: Content specifications for Earth observation data and derived digital products." The development of this extension is in progress with participation by an international team representing nine countries. The purpose of this paper is to introduce this standard and report on its status.

Remote Sensing; Data Systems; Open Data;↗
NASA NTRS2014

Spring 2014 Internship Diffuser Data Analysis

J-2X engine testing on the A-2 test stand at the NASA John C. Stennis Space Center (SSC) has recently concluded. As part of that test campaign, the engine was operated at lower power levels in support of expanding the use of J-2X to other missions. However, the A-2 diffuser was not designed for engine testing at the proposed low power levels. To evaluate the risk of damage to the diffuser, computer simulations were created of the rocket engine exhaust plume inside the 50ft long, water-cooled, altitude-simulating diffuser. The simulations predicted that low power level testing would cause the plume to oscillate in the lower sections of the diffuser. This can possibly cause excessive vibrations, stress, and heat transfer from the plume to the diffuser walls. To understand and assess the performance of the diffuser during low power level engine testing, nine accelerometers and four strain gages were installed around the outer surface of the diffuser. The added instrumentation also allowed for the verification of the rocket exhaust plume computational model. Prior to engine hot-fire testing, a diffuser water-flow test was conducted to verify the proper operation of the newly installed instrumentation. Subsequently, two J-2X engine hot-fire tests were completed. Hot-Fire Test 1 was 11.5 seconds in duration, and accelerometer and strain data verified that the rocket engine plume oscillated in the lower sections of the diffuser. The accelerometers showed very different results dependent upon location. The diffuser consists of four sections, with Section 1 being closest to the engine nozzle and Section 4 being farthest from the engine nozzle. Section 1 accelerometers showed increased amplitudes at startup and shutdown, but low amplitudes while the diffuser was started. Section 3 accelerometers showed the opposite results with near zero G amplitudes prior to and after diffuser start and peak amplitudes to +/- 100G while the diffuser was started. Hot-Fire Test 1 strain gages showed different data dependent on section. Section 1 strains were small, and were in the range of 50 to 150 microstrain, which would result in stresses from 1.45 to 4.35 ksi. The yield stress of the material, A-285 Grade C Steel, is 29.7 ksi. Section 4 strain gages showed much higher values with strains peaking at 1600 microstrain. This strain corresponds to a stress of 46.41 ksi, which is in excess of the yield stress, but below the ultimate stress of 55 to 75 ksi. The decreased accelerations and strain in Section 1, and the increased accelerations and strain in Sections 3 and 4 verified the computer simulation prediction of increased plume oscillations in the lower sections of the diffuser. Hot-Fire Test 2 ran for a duration of 125 seconds. The engine operated at a slightly higher power level than Hot-Fire Test 1 for the initial 35 seconds of the test. After 35 seconds the power level was lowered to Hot-Fire Test 1 levels. The acceleration and strain data for Hot-Fire Test 2 was similar during the initial part of the test. However, just prior to the engine being lowered to the Hot-Fire Test 1 power level, the strain gage data in Section 4 showed a large decrease to strains near zero microstrain from their peak at 1500 microstrain. Future work includes further strain and acceleration data analysis and evaluation.

Laigaie, Robert T.↗
NASA NTRS1985

Review of research on wave mean flow interactions using FGGE data

Comparison is made between the conventional Eulerian diagnostics of wave mean flow interactions in the atmosphere and the diagnostics introduced by Andrews and McIntyre (1976). In the latter, the meridional circulation is represented by a residual circulation, and the eddy torque in the zonal momentum equation by the Eliassen-Palm (1960) flux divergence (or equivalently, by the poleward eddy flux of geostrophic potential vorticity). It is found that, while the new diagnostics are useful in studying stratospheric warmings and transports of conservative quantities, the conventional diagnostics are more useful in studying global energetics and wave mean flow interactions in the troposphere and lower stratosphere. Case studies diagnosed with FGGE IIIb data are presented to illustrate this point. Kung and Tanaka's (1983) comparisons of the atmospheric energy cycle for SOP-1 and SOP-2, estimated with the use of the ECMWF and GFDL FGGE IIIb data bases, are used to assess the uncertainty in calculations of energetics based on the use of FGGE IIIb data. These results demonstrate the high degree of model dependence in the FGGE IIb data sets.

Pfeffer, R. L.↗
NASA NTRS1997

Improvements for Image Compression Using Adaptive Principal Component Extraction (APEX)

The issues of image compression and pattern classification have been a primary focus of researchers among a variety of fields including signal and image processing, pattern recognition, data classification, etc. These issues depend on finding an efficient representation of the source data. In this paper we collate our earlier results where we introduced the application of the. Hilbe.rt scan to a principal component algorithm (PCA) with Adaptive Principal Component Extraction (APEX) neural network model. We apply these technique to medical imaging, particularly image representation and compression. We apply the Hilbert scan to the APEX algorithm to improve results

Ziyad, Nigel A.↗
NASA NTRS2005

Apparatus Characterizes Transient Voltages in Real Time

The figure shows a prototype of a relatively inexpensive electronic monitoring apparatus that measures and records selected parameters of lightning-induced transient voltages on communication and power cables. The selected parameters, listed below, are those most relevant to the ability of lightning-induced transients to damage electronic equipment. This apparatus bridges a gap between some traditional transient-voltage recorders that record complete waveforms and other traditional transient-voltage recorders that record only peak values: By recording the most relevant parameters and only those parameters this apparatus yields more useful information than does a traditional peak-value (only) recorder while imposing much smaller data-storage and data-transmission burdens than does a traditional complete-waveform recorder. Also, relative to a complete-waveform recorder, this apparatus is more reliable and can be built at lower cost because it contains fewer electronic components. The transients generated by sources other than lightning tend to have frequency components well below 1 MHz. Most commercial transient recorders can detect and record such transients, but cannot respond rapidly enough for recording lightning-induced transient voltage peaks, which can rise from 10 to 90 percent of maximum amplitude in a fraction of a microsecond. Moreover, commercial transient recorders cannot rearm themselves rapidly enough to respond to the multiple transients that occur within milliseconds of each other on some lightning strikes. One transient recorder, designed for Kennedy Space Center earlier [ Fast Transient-Voltage Recorder (KSC- 11991), NASA Tech Briefs, Vol. 23, No. 10, page 6a (October 1999)], is capable of sampling transient voltages at peak values up to 50 V in four channels at a rate of 20 MHz. That recorder contains a trigger circuit that continuously compares the amplitudes of the signals on four channels to a preset triggering threshold. When a trigger signal is received, a volatile memory is filled with data for a total time of 200 ms. After the data are transferred to nonvolatile memory, the recorder rearms itself within 400 ms to enable recording of subsequent transients. Unfortunately, the recorded data must be retrieved through a serial communication link. Depending on the amount of data recorded, the memory can be filled before retrieval is completed. Although large amounts of data are recorded and retrieved, only a small part of the information (the selected parameters) is usually required. The present transient-voltage recorder provides the required information, without incurring the overhead associated with the recording, storage, and retrieval of complete transient-waveform data. In operation, this apparatus processes transient voltage waveforms in real time to extract and record the selected parameters. An analog-to-digital converter that operates at a speed of as much as 100 mega-samples per second is used to sample a transient waveform. A real-time comparator and peak detector are implemented by use of fast field-programmable gate arrays.

Medelius, Pedro↗
NASA NTRS2021

Observation of Low-Energy Proton Direct Ionization in a 72-Layer 3D NAND Flash Memory

Single-event upsets are observed in a 72-layer 3D NAND flash memory operated in single-level cell mode after low-energy proton (500 keV-1.2 MeV) and heavy ion irradiation. The layer-by-layer error count is analyzed to visualize the stopping of low energy protons within the memory stack, and Monte Carlo simulations are correlated with the experimental data. Direct ionization by low-energy protons is identified by three-dimensional data analysis and the energy dependence of device sensitive cross-section. Heavy ion data is also presented for comparison.

Direct ionization↗
NASA NTRS1997

High-Resolution Temperature-Dependent Photoabsorption Cross Section Measurements of S2, with Application to HST UV Spectra of SL9/Jupiter

The Hubble Space Telescope (HST) UV spectra of Jupiter after the collision of Comet SL9 show predominantly molecular features of S2, CS2, NH3, and H2S in the 1800-3200 A region. The HST observations were made under various phases of impact conditions which gave temperatures higher than 1000 K. It is thus clear that temperature-dependent laboratory cross section data are required in order to determine the molecular abundances in Jupiter's atmosphere after the impact of Comet Shoemaker-Levy 9. The required high-resolution temperature dependent S2 absorption cross sections have not been directly measured in the laboratory. To provide the required data for modelers our objective is to accurately measure the high-resolution (FWHM = 0.003 A) and medium resolution (FWHM - 0.08 A) temperature dependent S2 in the 2450-3200 A region. Using the experimental setup we have obtained absorbtion spectra of S2 under various temperature conditions.

Wu, C. Y. Robert↗
NASA NTRS1981

Low-power portable geophysical data acquisition system and its use in geomagnetic measurements

A low-power portable data acquisition system presently in use for geomagnetic measurements is described. The system is composed of a data-processing system containing a low-power microprocessor, a 9-track digital tape recorder, and a rechargeable battery pack. The magnetometer is a low-power three axis fluxgate design. Under program control the data processing system keeps track of time of day and date, samples three analog magnetometer outputs at intervals of either 0.4 or 2 s, digitizes the data to 15-bit resolution, and, depending upon relative magnetic activity, decides upon data compression to increase the tape storage capacity. It also monitors and records internal voltages and provides self-checking functions which may be monitored through a visual readout on the control panel. The system is mounted in a rugged, weather-tight carrying case suitable for use outdoors with minimal protection. The system, including magnetometer, uses 1.6-W power and can store 5.7 Mbytes of data.

Medford, L. V.↗
NASA NTRS2004

Development of a Low Data Event Timer for Monitoring an Advancing Crack in Fracture

Monitoring the crack position and velocity in a fracture specimen can be difficult and laborious. In addition, the data storage requirements can be considerable depending upon the testing conditions. A low data event timer was developed to alleviate these problems. The test apparatus was applied to cantilever beams bonded with a structural epoxy and tested under different conditions such as stable to unstable transitions and different temperature extremes. The results indicate that the approach eliminates problems associated with other types of crack measurement and greatly simplifies the measuring process.

Macon, D. J.↗
NASA NTRS2021

Conceptualizing the Impact of Dust Contaminated Infrared Radiances on Data Assimilation for Numerical Weather Prediction

Numerical weather prediction systems depend on Hyperspectral Infrared Sounder (HIS) data, yet the impacts of dust-contaminated HIS radiances on weather forecasts has not been quantified. To determine the impact of dust aerosol on HIS radiance assimilation, we use a modified radiance assimilation system employing a one-dimensional variational assimilation system (1DVAR) developed under the European Organisation for the Exploitation of Meteorological Satellites (EUMETSAT) Numerical Weather Prediction–Satellite Application Facility (NWP-SAF) project, which uses the Radiative Transfer for TOVS (RTTOV). Dust aerosol impacts on analyzed temperature and moisture fields are quantified using synthetic HIS observations from rawinsonde, Micropulse Lidar Network (MPLNET), and Aerosol Robotic Network (AERONET). Specifically, a unit dust aerosol optical depth (AOD) contamination at 550 nm can introduce larger than 2.4 and 8.6 K peak biases in analyzed temperature and dewpoint, respectively, over our test domain. We hypothesize that aerosol observations, or even possibly forecasts from aerosol predication models, may be used operationally to mitigate dust induced temperature and moisture analysis biases through forward radiative transfer modeling.

Jared W. Marquis↗
NASA NTRS2021

Conceptualizing the Impact of Dust-Contaminated Infrared Radiances on Data Assimilation for Numerical Weather Prediction

Numerical weather prediction systems depend on Hyperspectral Infrared Sounder (HIS) data, yet the impacts of dust-contaminated HIS radiances on weather forecasts has not been quantified. To determine the impact of dust aerosol on HIS radiance assimilation, we use a modified radiance assimilation system employing a one-dimensional variational assimilation system (1DVAR) developed under the European Organisation for the Exploitation of Meteorological Satellites (EUMETSAT) Numerical Weather Prediction–Satellite Application Facility (NWP-SAF) project, which uses the Radiative Transfer for TOVS (RTTOV). Dust aerosol impacts on analyzed temperature and moisture fields are quantified using synthetic HIS observations from rawinsonde, Micropulse Lidar Network (MPLNET), and Aerosol Robotic Network (AERONET). Specifically, a unit dust aerosol optical depth (AOD) contamination at 550 nm can introduce larger than 2.4 and 8.6 K peak biases in analyzed temperature and dewpoint, respectively, over our test domain. We hypothesize that aerosol observations, or even possibly forecasts from aerosol predication models, may be used operationally to mitigate dust induced temperature and moisture analysis biases through forward radiative transfer modeling.

Jared W Marquis↗
NASA NTRSDate not supplied

Materials Informatics at NASA GRC: Machine Learning Surrogate Modeling, Data Management, and Integrated Toolsets for Establishing/Maintaining the Digital Thread

Integrated Computational Materials Engineering (ICME) has recently received widespread attention due to its promises in reducing dependence on physical testing for engineering design by relying on simulation, reducing both time and cost to market for various applications. ICME however requires validated multiscale material models, which heavily depend on available test data with full material and test pedigree, including material processing, test and measurement equipment, raw data collection, and analysis methodology and results that is findable and usable, along with integrated, efficient toolsets for effectively passing information across various length and time scales across such models. At the NASA Glenn Research Center under the Transformational Tools and Technologies Project, significant recent efforts have been directed towards establishing the required cyberinfrastructure to enable optimized ICME processes and the design of “fit-for-purpose” materials to achieve the goals outlined in the NASA Vision 2040 report. Such efforts include development of multiscale physics-based material models, which can be used to train highly efficient surrogate machine learning models, development of best practices and infrastructure for effective, traceable materials information management, and development of toolsets that integrate with physics-based codes, machine learning models, and an information management system to enable high throughput of materials data collection and analysis, establishment of digital twins and the digital thread, and automation of the ICME design process for material optimization.

Machine Learning↗
NASA NTRS1994

Response of a two-dimensional dual-Doppler radar wind synthesis

The wind field resulting from a two-dimensional dual-Doppler synthesis algorithms is spectrally modified from the true wind field. The effects of spatial filtering on wind fields from the processes of interpolation, the averaging of pulses, and the effect of the finite radar pulse dimension were assessed. The effect resulting from the use of different interpolation techniques was also evaluated. Of those techniques tested, the best are the Cressman distance-weighted averaging and linear distance-weighted averaging, with the closest neighbor and uniform weighting having more undesirable characteristics. The optimum influence radius is defined as the influence radius at which the ratio of the rms difference between the Fourier and least-squares responses (a measure of the aliasing) and the variance of the filtered wind field is minimized. This seeks to minimize the effect of energy aliased into scales other than the input wavelength. For the Cressman interpolation technique, the optimum influence radius is between 1.85 and 2.25 times the maximum data spacing. The range of acceptable influence radii includes consideration of the filtering by the radar of the data as it is collected, as well as the resolution of the final dataset. The optimum influence radius is dependent upon the largest data separation in the analysis domain. The absolute optimum influence radius is not significantly affected by inclusion of the radar-beam filtering effects.

Given, Terence↗
NASA NTRS1998

Growth of (101) Faces of Tetragonal Lysozyme Crystals: Measured Growth Rate Trends

Earlier extensive measurements of the growth rates of the (110) face of tetragonal lysozyme crystals had shown unexpected dependencies on the supersaturation. In this study similar growth rate measurements were done for the (101) faces of the crystals. The data show a similar dependence on the supersaturation, becoming appreciable only at high supersaturations, reaching a maximum value and then decreasing. As reported in earlier studies, the (101) growth rates are larger at low supersaturations than the (110) growth rates at the same conditions, and smaller at high supersaturations. These trends suggest that the growth mechanism of the (101) is similar to that of the (110) face, involving the addition of lysozyme aggregates formed in solution, but with a growth unit smaller than that of the (110) face.

Forsythe, Elizabeth L.↗