Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “correspondence”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
NASA NTRS2018

Effect of Distributed Patch of Smooth Roughness Elements on Transition in a High-Speed Boundary Layer

Surface roughness is known to have a substantial impact on the aerothermodynamic loading of hypersonic vehicles, particularly via its influence on the laminar-turbulent transition process within the boundary layer. Numerical simulations are performed to investigate the effects of a distributed region of densely packed, smooth-shaped roughness elements on the laminar boundary layer over a 7-degree half-angle, circular cone for flow conditions corresponding to a selected trajectory point from the ascent phase of the HIFiRE-1 flight experiment. For peak-to-valley roughness heights of 50 percent or less in comparison with the thickness of the unperturbed boundary layer, the computations converge to a stationary flow, suggesting that the flow is globally stable. Analysis of convective instabilities in the wake of the roughness patch indicates two dominant families of unstable disturbances, namely, a high frequency mode that corresponds to Mack mode waves modified by the wake and a lower frequency mode that corresponds to shear layer instabilities associated with the streaks in the roughness wake. Even though the peak growth rate of the later mode is more than 35 percent greater than the peak growth rates of the Mack modes, the latter modes achieve higher amplification ratios, and hence, are likely to dominate the onset of transition, which is estimated to occur slightly later than that in the unperturbed, i.e., smooth surface boundary layer. Additional computations are performed to investigate the effects of various roughness patch configurations on a Mach 3.5 flat plate boundary layer, to help guide an upcoming experiment in the Mach 3.5 Supersonic Low Disturbance Tunnel at NASA Langley Research Center. In this case, the cumulative reinforcement of basic state distortion over the length of the roughness patch is predicted to yield a significantly earlier transition than that over a smooth plate or a plate with a shorter length roughness patch.

Meelan Choudhari↗
NASA NTRSDate not supplied

Multi-point Jig Twist Optimization of Mach 0.745 Transonic Truss-Braced Wing Aircraft and High-Fidelity CFD Validation

This paper presents a multi-point jig twist optimization study of the Mach 0.745 Transonic Truss-Braced Wing (TTBW) aircraft using an in-house developed aero-structural analysis solver VSPAERO coupled to BEAM3D. A vortex-lattice model of the TTBW model is developed, and a transonic small disturbance /integral boundary layer correction method is implemented in the VSPAERO model to account for transonic and viscous flow effects. A correction method for the wing-strut interference aerodynamics is developed and applied to the VSPAERO solver. Also, a structural dynamic finite-element model of the TTBW aircraft is developed. This finite-element model includes the geometric nonlinear effect due to the tension in the struts which causes a deflection-dependent nonlinear stiffness. The VSPAERO model is coupled to the corresponding finite-element model to provide a rapid aero-structural analysis. The VSPAERO model has been validated against wind tunnel test data and FUN3D CFD simulation data. Three different flight conditions corresponding to Mach 0.745 at 40,000 ft are selected for the TTBW aircraft jig twist optimization to reduce the drag coefficients at the design and off-design cruise lift coefficients. The preliminary optimization results show that the TTBW aircraft with the optimized jig twist achieves a drag reduction of about 9 counts, 7 counts, and8 counts corresponding to the lift coefficients 0.68, 0.73, and 0.78, respectively. A high-fidelity CFD solver FUN3D is used to validate the jig twist optimization.

Multi-point↗
NASA NTRS2021

Summer temperatures during the last glaciation (MIS 5c to MIS 3) inferred from a 50,000-year chironomid record from Füramoos, southern Germany

There is a sparsity of long, continuous palaeotemperature records for the last glacial period in central Europe, particularly for the interval corresponding to Marine Isotope Stages (MIS) 4 and 3. Here we present a new, ca. 50-thousand year (ka)-long chironomid record from Füramoos, southern Germany, covering the interval from MIS 5a to MIS 3 that we use to examine lake development and then to quantitatively reconstruct mean July air temperatures. Chironomid assemblages with high abundances of taxa such as Polypedilum nubeculosum-type, Microtendipes pedellus-type, Cladopelma lateralis-type and Dicrotendipes nervosus-type imply a shallow-lake setting for the majority of the examined interval, which is corroborated by other aquatic remains such as oribatid mites, Sialidae and Ceratopogonidae. Assemblages from the interval ca. 99 to 80 ka (in the region corresponding to the Brörup Interstadial, Stadial B and early Odderade Interstadial) are dominated by taxa such as Tanytarsus glabrescens-type and Tanytarsus mendax-type and indicate relatively warm temperatures. Assemblages from the interval covering ca. 80 to 54 ka (corresponding to the late Odderade, Stadial C, Dürnten Interstadial and Stadial D) are dominated by taxa such as Sergentia coracina-type and Tanytarsus lugens-type and are typical for cooler conditions. Reconstructed July temperatures for the early Würmian (Brörup to early Odderade; ca. 99–80 ka) are 13–14 °C. Values decline to <10 °C during the late Odderade and Stadial C (ca. 80–77 ka) around the MIS 5a/4 transition. This decrease is coeval with a pronounced decrease in Northern Hemisphere summer insolation. Values stay in the range of 9–11 °C during the Dürnten and Stadial D (ca. 54–74.5 ka) and increase again to 12.5 °C during the Bellamont 1 interstadial (ca. 54–46 ka). Reconstructed July temperatures track changes in arboreal pollen percentages at Füramoos and agree with a summer-temperature decrease during the early to mid-Würmian as reported by other palaeotemperature records from Europe and the North Atlantic. Our chironomid record from Füramoos provides valuable new insights into Würmian climate dynamics in Central Europe, and corroborates other temperature reconstructions from the early to mid-Würmian glacial period.

Chironomids↗
NASA NTRS2021

The Atacama Cosmology Telescope: A search for Planet 9

We use Atacama Cosmology Telescope (ACT) observations at 98 GHz (2015–2019), 150 GHz (2013–2019), and 229 GHz (2017–2019) to perform a blind shift-and-stack search for Planet 9. The search explores distances from 300 au to 2000 au and velocities up to 6\farcm3 per year, depending on the distance (r). For a 5 Earth-mass Planet 9 the detection limit varies from 325 au to 625 au, depending on the sky location. For a 10 Earth-mass planet the corresponding range is 425 au to 775 au. The predicted aphelion and most likely location of the planet corresponds to the shallower end of these ranges. The search covers the whole 18,000 square degrees of the ACT survey. No significant detections are found, which is used to place limits on the millimeter-wave flux density of Planet 9 over much of its orbit. Overall we eliminate roughly 17% and 9% of the parameter space for a 5 and 10 Earth-mass Planet 9, respectively. These bounds approach those of a recent INPOP19a ephemeris-based analysis, but do not exceed it. We also provide a list of the 10 strongest candidates from the search for possible follow-up. More generally, we exclude (at 95% confidence) the presence of an unknown solar system object within our survey area brighter than 4–12 mJy (depending on position) at 150 GHz with current distance 300 au < r < 600 au and heliocentric angular velocity 1\farcm5 per yr < v x (500au/r) < 2\farcs3 per yr, corresponding to low-to-moderate eccentricities. These limits worsen gradually beyond 600 au, reaching 5–15 mJy by 1500 au.

Sigurd Naess↗
NASA NTRS2021

A Living Catalog of Stream Interaction Regions in the Parker Solar Probe Era

Stream interaction regions (SIRs) and corotating interaction regions (CIRs) are important phenomena in heliospheric physics. These large-scale structures vary temporally and spatially, both in latitude and with radial distance. The additions of Parker Solar Probe(PSP) and Solar Orbiter have allowed for investigations into the radial evolution of these structures over a wide range of heliocentric distances for the first time since the Helios era. To better enable investigations of SIRs and CIRs within the inner heliosphere, we have developed a living catalog of SIR and CIR observations by Parker Solar Probe with corresponding observations by STEREO-A as well as ACE and Wind at 1 au. The methodology used for the identification of events and the generation of this catalog, the initial catalog of PSP observations spanning orbits one through five along with corresponding 1 au observations, and information on accessing the living catalog for future studies is described. This list of SIR and CIR events from PSP and corresponding observations from other heliophysics missions will enable case studies utilizing unique orbital arrangements, as well as aid in future statistical studies to further understand the properties and evolution of these structures.

Catalogs↗
NASA NTRS2020

Conditions of Loss Cone Filling by Scattering on the Curved Field Lines for 30 keV Protons During Geomagnetic Storm as Inferred From Numerical Trajectory Tracing

The rate of pitch angle scattering on the curved magnetic field lines is well parameterized by the ratio of the minimum field line curvature radius to the maximum effective particle gyroradius (K = RC/rg). The critical value of this ratio (Kcr) corresponding to the loss cone filling is of special interest since it corresponds to the low altitude isotropic boundaries (IBs). The early theoretical estimates gave Kcr = 8, whereas recent estimations of the K parameter on the field lines corresponding to the observed IBs during the geomagnetic storms revealed KIB values in the range of 3–30. We numerically trace the trajectories of the 30 keV protons in the magnetic field of the global magnetohydrodynamic simulation of the intense storm in order to infer statistical distribution of Kcr. The electric field and effects of nonstationarity are neglected in this study. It is found that although the Kcr values do show some variations during the course of the storm, its range is rather narrow 4 < Kcr < 8. The result suggests that higher KIB values found in the observational studies, if not caused by the magnetosphere-ionosphere mapping error, should be attributed to some other mechanism of pitch angle scattering. The Kcr values tend to be lower (4–6) during the main phase because the region of low K values approaches the Earth and the equatorial loss cone size becomes larger due to a larger equatorial magnetic field in the near earth region. The remaining variation of Kcr is explained by the presence of the guide component of the magnetic field.

S Dubyagin↗
NASA NTRS2022

An Investigation Into Some Important Aspects of Droplet Breakup/Vaporization Behavior Caused By a Gas Flow (Both Nonreacting & Detonative Combustion) in a Shock Tube

As a part of the rotating detonation engine (RDE) technology enablement project at NASA Glenn Research Center (GRC), an effort was undertaken to extend our current computational capabilities of OpenNCC in some important ways with the implementation of a modeling approach to account for the droplet breakup caused by a shock-induced gas motion, & a vaporization model valid over a wide range of pressure conditions encountered in multiphase detonation. With the modified code, a study was undertaken to investigate the individual droplet behavior followed by the passage of a shock front. The study is carried out by tracking a sparse group of droplets to gain some understanding of shock induced droplet behavior under various shock strengths & fuel injector conditions. The study also looks into the effect of randomization involved in determining the droplet breakup outcomes. Over a wide range of sub-critical conditions examined, larger droplets are observed to undergo significant changes in droplet behavior following their breakup. However, smaller droplets (10 µm or less ) remain unaffected by any shock induced breakup. In a follow-on work, we investigated the impact of shock and droplet interaction in a detonation study involving both gaseous as well as gas/liquid (droplet clouds) fuel/air stoichiometric mixtures in a simple 3D shock-tube configuration. The droplet clouds are made up of different initial droplet sizes of either 6, 10, or 30 µm. We also investigated the individual droplet behavior followed by the passage of a detonation front. The results represent conditions that lead to both overdriven and C-J (ChapmanJouguet) detonations. Under both test conditions, most of the droplet vaporization is completed within a short distance (duration) behind the detonation front & well within the region of complete combustion observed in a corresponding equivalent gas-phase fuel/air mixture. The impact of the shock-induced droplet breakup is found to be significant in the calculations involving the 30-µm droplets. Subsequent to the breakup, the drop sizes vary from 1 to 10 µm. Another factor that contributed to the observed rapid vaporization is the result of vaporization taking place under supercritical conditions. The overall detonation properties of various droplet clouds (made up of different initial sizes) are similar to those observed in a corresponding gaseous fuel/air mixture. In the calculation involving a gaseous fuel, the calculated C-J detonation velocity is 1822 m/s involving Jet-A/air and φ = 1. In the overdriven detonation, it is 2044 m/s. In the calculations involving droplet clouds, the corresponding detonation velocities are lower. The impact of increased droplet size is primarily seen in a higher reduction in the detonation velocity.

shock/droplet interaction↗
NASA NTRS2022

Aerosol Models from the AERONET Database: Application to Surface Reflectance Validation Satellite Data

Aerosols play a critical role in radiative transfer within the atmosphere, and they have a significant impact on climate change. In this paper, we propose and implement a framework for developing an aerosol model using their microphysical properties. Such microphysical properties as the size distribution, the complex refractive index, and the percentage of sphericity are derived from the global AERosol RObotic NETwork (AERONET). These measurements, however, are typically retrieved when almucantar measurement procedures are performed (i.e., early mornings and late afternoons with clear sky) and might not have a temporal correspondence to a satellite overpass time, so a valid validation of satellite-derived products cannot be carried out. To address this problem of temporal inconsistency of satellite and ground-based measurements, we developed an approach to retrieve these microphysical properties (and the corresponding aerosol model) using the optical thickness at 440 nm, τ440, and the Ångström coefficient between 440 and 870 nm, α440–870. Such aerosol models were developed for 851 AERONET sites within the last 28 years. Obtained results suggest that empirically microphysical properties can be retrieved with uncertainties of up to 23 %. An exception is the imaginary part of the refractive index ni, for which the derived uncertainties reach up to 38 %. These specific parametric models of aerosol can be used for the studies when retrieval of microphysical properties is required as well as validation of satellite-derived products over land. Specifically, we demonstrate the usefulness of the aerosol models to validate surface reflectance records over land derived from optical remote sensing sensors. We then quantify the propagation of uncertainties in the surface reflectance due to uncertainties with the aerosol model retrieval that is used as a reference from radiative transfer simulations. Results indicate that individual aerosol microphysical properties can impact uncertainties in surface reflectance retrievals between 3.5 × 10(exp -5) to 1 × 10(exp -3) (in reflectance units). The overall impact of microphysical properties combined yields an overall uncertainty in surface reflectance <0.004 (in reflectance units). That corresponds, for example, to 1 to 3 % of the retrieved surface reflectance in the red spectral band (620–670 nm) by the Moderate Resolution Imaging Spectroradiometer (MODIS) instrument. These uncertainty values are well below the specification (0.005 + 0.05ρ; ρ is the retrieved surface reflectance) used for the MODIS atmospheric correction.

Jean-Claude Roger↗
NASA NTRSDate not supplied

Aeroelastic Trim Drag Optimization of Mach 0.8 TransonicTruss-Braced Wing Aircraft with Variable Camber ContinuousTrailing Edge Flap

This paper presents an aeroelastic trim drag optimization study of the Mach 0.8 Tran-sonic Truss-Braced Wing (TTBW) aircraft with the Variable Camber Continuous TrailingEdge Flap (VCCTEF). An aero-structural analysis solver VSPAERO with transonic small dis-turbance, integral boundary-layer, and wing-strut interference corrections coupled to modeshapes computed by NASTRAN using the Galerkin method is developed to provide a rapidaircraft aeroelastic performance evaluation. Aeroelastic trim drag optimization studies areconducted for a VCCTEF configuration with 6-spanwise sections. Three different flight condi-tions corresponding to Mach 0.8 are selected for the aeroelastic trim drag optimization at thedesign and off-design cruise lift coefficients. The preliminary optimization results show thatthe TTBW aircraft with the optimized VCCTEF deflection achieves a drag reduction of about 9.2 counts, 9.6 counts, and 12.3 counts corresponding to the lift coefficients 0.661, 0.695, and0.729, respectively. When accounting for the actuator weight penalty, the corresponding dragreductions are 1.77%, 1.82%, 2.41%. A high-fidelity CFD solver FUN3D is used to validatethe aeroelastic trim drag optimization.

Aeroelastic trim drag↗
NASA NTRSDate not supplied

On Improving the Dust Lidar Ratios for Version 5 of CALIOP by Using Measurements with Source-tagged Model Results

Vertically resolved retrievals of aerosol backscatter and extinction have been available since 2006 from global measurements acquired by the space borne lidar CALIOP onboard the CALIPSO satellite. These retrievals depend crucially upon the ratio of extinction to backscatter (i.e., lidar ratio) which typically has to be assumed for the various aerosol species for an elastic backscatter lidar like CALIOP. For all CALIPSO data releases up until now (version 4.2), these lidar ratios have been taken as constant both spatially and temporally. However, it is well established that the aerosol lidar ratios can vary significantly regionally, seasonally, and also as a function of age and relative humidity. In particular, the dust lidar ratios show significant variation depending upon their source regions, which is related to the mineral composition of dust in that region. In this paper, we shall present a scheme to obtain the regionally and seasonally dependent lidar ratios of dust. In this scheme, which may be implemented in a forthcoming version of CALIOP aerosol extinction retrievals, we first derive lidar ratios of aerosol layers globally, classified as dust by CALIOP, by using the backscatter measurements constrained by collocated MODIS aerosol optical depths. Since this dust will frequently be a mixture of dust from various source regions, we obtain the corresponding regional contributions from the dust simulations using the GEOS model tagged to nine source regions. Finally, combining information from both measurements and models, we obtain the lidar ratios of dust corresponding to the nine source regions. The lidar ratio of the mixed dust anywhere can now be obtained from the tagged model fractions and the corresponding regional lidar ratio. We shall show the application of this scheme for various regions and seasons.

CALIPSO↗
NASA NTRS2022

Four Sub-Jovian-Mass Planets Detected by High-Cadence Microlensing Surveys

Aims. With the aim of finding short-term planetary signals, we investigated the data collected from current high-cadence microlensing surveys. Methods. From this investigation, we found four planetary systems with low planet-to-host mass ratios, including OGLE-2017-BLG- 1691L, KMT-2021-BLG-0320L, KMT-2021-BLG-1303L, and KMT-2021-BLG-1554L. Despite the short durations, ranging from a few hours to a couple of days, the planetary signals were clearly detected by the combined data of the lensing surveys. We found that three of the planetary systems have mass ratios on the order of 10−4 and the other has a mass ratio that is slightly greater than 10−3. Results. The estimated masses indicate that all discovered planets have sub-Jovian masses. The planet masses of KMT-2021-BLG- 0320Lb, KMT-2021-BLG-1303Lb, and KMT-2021-BLG-1554Lb correspond to ∼0.10, ∼0.38, and ∼0.12 times the mass of the Jupiter, and the mass of OGLE-2017-BLG-1691Lb corresponds to that of the Uranus. The estimated mass of the planet host KMT-2021-BLG- 1554L, M host ∼ 0.08 M ⊙ , corresponds to the boundary between a star and a brown dwarf. Besides this system, the host stars of the other planetary systems are low-mass stars with masses in the range of ∼[0.3–0.6] M ⊙ . The discoveries of the planets fully demonstrate the capability of the current high-cadence microlensing surveys in detecting low-mass planets.

planets and satellites: detection↗
NASA NTRSDate not supplied

Preliminary Results Cycling GEOS-JEDI with GSI-based Background Errors

The first phase of transitioning the NASA GMAO GEOS atmospheric data assimilation capabilities to JEDI involves the replacement of the Grid-point Statistical Interpolation (GSI) with a corresponding JEDI analysis. This includes taking JEDI's Unified Observation Operator (UFO), its underlying dependencies, and the JEDI solver that enables a hybrid 4DEnVar strategy similar to what is used in the current GEOS-GSI system. Variational analysis involves at least two main components associated with the observation and background cost function terms. The first is directly related to the UFO, which is being carefully validated in a joint collaboration between GMAO and NCEP to demonstrate consistency with corresponding observations usage in GSI. The second component is the background term, which in a hybrid system involves the ability to set up both a climatologically-based term and an ensemble-based term. JEDI provides the means to implement both terms through its BUMP component. Use of BUMP would require a complete re-tune of both climatological and ensemble, which is a non-trivial exercise we would prefer to avoid. As an alternative, the work here studies the results of interfacing the GSI-background error capability (GSIBEC) into JEDI through SABER. With this, the exact same background error covariance formulation used in GSI can be employed in JEDI without need for re-tuning. This brief summary covers the work done to interface GSIBEC into JEDI and shows preliminary results where the background error covariances of the control (GEOS-GSI) and experiment (GEOS-JEDI) are identical in corresponding cycling experiments. The cycling exercise is obviously preliminary and so much can be expected from GEOS-JEDI when compared to GEOS-GSI. There is still a number of features that need closer attention and although in some cases in principle ready to cycle have been intentionally either turned off or not fully exercised (e.g., VarBC is applied but not cycled). Other features are still pending implementation, one such example is the implementation of the Tangent Linear Normal Mode Constraint. Still, results are quite encouraging as hopefully the discussion here illustrates.

Ricardo Todling↗
NASA NTRSDate not supplied

Geochemical Insights Into Volcanic and Lithospheric Evolution of Mars

Introduction: The Martian lithosphere plays a pivotal role in volcanic processes, altering surface features, climate shifts, and the planet's early habitability. Crucially, the rigid lithosphere significantly influences Mars' long-term thermal conditions. Studying various geological eons’ volcanic compositions unveils how the lithosphere has evolved, even though understanding the early Noachian volcanic chemistry remains challenging due to weathering and resurfacing. In this study, newly discovered Noachian volcanic terranes[1-2] along with Hesperian and Amazonian volcanic terranes[3] are considered(Figure 1), to infer the evolution of the Martian lithosphere. Figure 1:Mars topographic map derived from MOLA-HRSC data [4] highlights the study regions including the Noachian volcanic terranes, Arabia Terra (AT), Thaumasia Minor (TM), and the Southwest Margin of Icaria Planum (SWIP)[5].Additionally, the Hesperian volcanic terranes such as Syrtis Major (SM), Hesperia Planum (HP), and, the Amazonian volcanic terranes encompass Elysium Mons (EM), Alba Patera (AP), and Olympus Mons (OM) are marked. Methods and Datasets: We use the most recent elemental mass fraction maps derived from gamma spectroscopy data from the Mars Odyssey 2001mission [6]to ascertain the bulk composition of the Martian landscape. Utilizing the updated geochemical provinces dataset of Mars[7], we consider bulk chemistry variations within our study regions. The maps, at a resolution of 50×50, encompass elements like Al, Ca, Fe, Si, K, Th, H2O, Cl, and S, detected through Gamma-Ray Spectroscopy (GRS) with decimeter scale depth sensitivity[6].Additional major and minor elements like Mg, Na, Ti, P, and Mn, using mass balance methods [8]serve as inputs for melting and crystallization simulations. We employ the pMELTS model with FMQ-3to FMQ oxygen fugacity to estimate the Pressure(P)and melting degree(F)in various eons of volcanic terranes. We have also used conventional thermobarometric calculations to determine their formation P-T conditions, using silica activity and olivine-melt Mg-exchange thermometry[9-10]. Results: Chemical Composition of Studied Volcanic Terranes: To assess formation conditions, we have investigated if GRS-measured compositions signify primary igneous processes by evaluating weathering through the Chemical Index of Alteration (CIA), K/Th ratios, and ternary plots for aqueous alteration. Consistent K/Th ratios and low CIA (<50) across volcanic regions suggest minimal large-scale weathering, affirming well-preserved igneous material extending at decimeter depths. In addition, the calculated bulk compositions align with Martian mantle equilibrium, confirming studied volcanic terranes-Arabia Terra, Thaumasia Minor, and SWIP -as primary or less altered compositions, reinforcing their representativeness at a regional GRS scale on Mars. We have also estimated the bulk compositions of Hesperian and Amazonian volcanic terranes shown in Figure 1. All volcanic terranes represent the primary or minimally altered composition. Temporal Evolution of Martian Volcanic Terranes: Our results show P-T conditions ranging from 1.3-1.6 GPa and 1350-1390°C for Noachian terranes, while Hesperian volcanic terranes vary from 1.6-1.7 GPa and 1370-1395°C, and Amazonian volcanic terranes range between 1.9-2.8 GPa and 1380-1415°C. Our analyses correspond to lithospheric thicknesses/ depth of melting for Noachian which ranges from110-135 km, 120-235 km for Hesperian terranes, and 160-235 km for Amazonian terranes. Partial melting percentages (F) range from 8-12% for Noachian, 10-11% for Hesperian, and 10-12% for Amazonian. We have also calculated mantle potential temperatures (Tp) to show variations across epochs(Figure 2). Heat flux estimation shows variations from 51-65 mW/m2 for Noachian, 38-45 mW/m2for Hesperian, and 27-39 mW/m2for Amazonian terranes, implying temporal changes in lithospheric thickness and heat flow. Comparison of Noachian volcanic terranes with Hesperian and Amazonian reveals variations in lithospheric thickness and heat flux, indicating potential implications for Martian surface conditions, including volcanic activity, climate evolution, and early habitability. Figure 2: P-T diagram displays formation conditions of studied Martian volcanic regions using GRS data, alongside Noachian-age surface basalt samples from Gusev, Gale, and Jezero. Dashed lines represent Martian mantle potential temperatures, calculated by adding the latent heat of fusion to the equilibrium temperature at which melt and solid mantle coexist and subtracting the Martian adiabatic gradient corresponding to the depth of melt. The solid line shows the Martian mantle solidus [11].Discussion& Implication: The study explores Martian volcanic activity across eons. Uniform lithospheric thickness from the Noachian to Hesperian eons suggests persistent weak plumes until Hesperian, influencing heat flow variations. Noachian's high heat flux, likely due to concentrated radioactive elements, shows spatial heterogeneity, indicating early Mars' differentiated mantle. Volcanic outgassing plays avital role in the formation of the Martian climate, likely sustained water on the surface, influencing warm-wet or cold-dry conditions. Hesperian's favorable lithospheric heat flow (45 mW/m2) supports extended water existence, resembling Earth's conditions. Whereas, Amazonian's diminished heat flux (25 mW/m2) corresponds to water loss and arid climate. Hesperian's similar lithospheric thickness to mid-Noachian implies prolonged water retention, influencing climate and potential for astrobiological research, expanding perspectives for future Martian missions. Future work: As volcanism was active throughout its history. The emergence of Mars' extensive volcanic regions, known as large igneous provinces, which are linked to intermittent volcanic activity driven by mantle plumes, poses challenges to understanding the scale and persistence of these phenomena in Martian convection models. Therefore, understanding the regional-scale changes in eruptive processes within Martian volcanic provinces over time remains unclear and crucial for deciphering the evolution of the Martian interior without Earth-like plate tectonics. We will continue this work with petrological and thermoelastic analyses to study the compositional and spatiotemporal evolution of the Elysium Volcanic Province.

A Rani↗
NASA NTRS2024

Electrical Properties of Lunar Environment Used for Predicting Lunar RF Propagation Characteristics

This contribution treats the lunar propagation environment as a three region medium: lunar exosphere, lunar regolith, and lunar bedrocks. Then it provides models for predicting the electromagnetic characteristics of each region. The electromagnetic characteristics could be electric characteristics represented by the complex relative permittivity, or magnetic characteristics represented by the complex relative permeability or both electric and magnetic characteristics. The lunar exosphere and the lunar bedrocks have only electric characteristics. The lunar regolith has both electric and magnetic characteristics. The complex relative permittivity models for lunar regolith are mapping of the corresponding models for Earth surface components reported in ITU-R P. 527-6. The complex relative permittivity prediction model of lunar exosphere is expressed in terms of a plasma frequency similar to the ordinary wave critical frequency in the corresponding model for the ionosphere. Based on this fascicle the following can be concluded for the frequency bands of 390 MHz and above: • The lunar exosphere can be treated as a free space, • The lunar regolith can be considered as non-magnetic, • The regolith complex relative permittivity has no temperature dependence, • The real part of the regolith complex relative permittivity depends only on regolith bulk density and it has no frequency dependence, and • The variation of regolith complex relative permittivity with regolith depth should be taken into consideration. Moreover, at frequencies of 2400 MHz and above, the lunar regolith can be treated as a uniform medium with complex relative permittivity equal to the corresponding complex relative permittivity at the regolith surface.

Electrical Permittivity↗
NASA NTRSDate not supplied

Comparison of Orion Flywheel to Commercially Available Flywheel Device

INTRODUCTION: The chosen exercise device for the Orion Multi-purpose Crew Vehicle (MPCV) for Artemis missions is the Orion Flywheel (OFW), which was selected in 2017 from a pool of exercise devices. The Orion Flywheel is to be installed in the MPCV for its first use during the Artemis II mission and will be utilized for subsequent Artemis missions. The OFW provides the capability to perform both resistive and aerobic exercises while taking up a small volume and not requiring power. Aerobic exercise consists of rowing while resistive exercise includes the deadlift, harness squat, and deadlift high pull among others. The efficacy of the OFW as an exercise countermeasure to spaceflight deconditioning has not yet been fully evaluated. A future HRP-funded study using head-down tilt bed rest is planned to evaluate the efficacy of the OFW to mitigate aerobic and muscular deconditioning. The OFW, made by KBR, is a specialized device that poses high costs for purchase and maintenance. The aim of the study is to determine if a commercially available alternative could be used as a backup for the OFW during the bed rest study or as an alternative in other studies. This study seeks to compare the loading profile and mechanics of a commercial flywheel device (kBox Pro) with the three resistance settings of the OFW using a controlled, instrumented setup to validate its acceptability as a backup. METHODS: An experimental setup was designed to simulate human use of the OFW. Flywheel devices can have varied actuated inertial mass and strap length. The inertial mass refers to the flywheel itself or the object that spins as the result of the movement of the strap. The OFW has three gears actuated with a lever, with the low gear used for aerobic rowing and the medium and high gears used for resistance exercises. These gears correspond to increasing flywheel inertia, which corresponds to a certain number and sizes of inertial plates on a commercial flywheel. The kBox Pro has varied sizes of inertial discs that are installed to the external shaft of the device and can be configured to roughly match the inertia seen in the OFW per gear setting. The strap length can be adjusted to allow for different ranges of motion. The experimental setup allows for the simulation of rowing, harness squats, and deadlift high pulls with corresponding exercise strap lengths. All three OFW gears are to be tested, as well as multiple combinations of kBox discs. The setup was created using a system of pulleys and cables to minimize friction loss. The system is actuated through the dropping of a connected mass which, through the pulley system, pulls the strap of the exercise device upwards as if a human was exercising. A string potentiometer and tensile force transducer are used to measure strap displacement and strap force, respectively. The masses dropped are exercise chains that simulate the decrease in force observed throughout a typical exercise. As the chains are lowered to the ground, they begin to spool and therefore are no longer subjecting the exercise device’s strap to their load. This setup was designed to provide realistic loads and protect the OFW from damage, an important precaution because it’s the only available unit for research and ground operations. Data is to be collected across simulated exercises and with different strap lengths, with the same conditions collected on both the OFW and the kBox Pro. RESULTS: Data collection is ongoing for the kBox and the Orion Flywheel. CONCLUSIONS: Study results will inform if the OFW and a kBox Pro device can be deemed mechanically similar. Depending on the results, additional data collection may be required to assess the user experience between the devices. A key result of this study is a mechanical characterization of the OFW device, demonstrating the load and force profile using a repeatable test method. This data will guide next steps on potential kBox Pro modifications needed to produce a comparable exercise experience to the OFW.

Exercise↗
DOE OSTI2020

Apparatus and method for neighborhood-aware virtual to physical address translations

An apparatus and method performs neighborhood-aware virtual to physical address translations. A coalescing opportunity for a first virtual address is determined, based on completing a memory access corresponding to a page walk for a second virtual address. Metadata corresponding to the first virtual address is provided to a page table walk buffer based on the coalescing opportunity and a page walk for the first virtual address is performed based on the metadata corresponding to the first virtual address.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2020

On-the fly scheduling of execution of dynamic hardware behaviors

Methods for dynamically executing computer code across multiple disparate processing unit architectures are disclosed. During execution of a first portion of computer code on a first processing unit, it is determined that a first dynamic hardware behavior of a plurality of dynamic hardware behaviors will occur at a subsequent point in time, based on a second dynamic hardware behavior that is occurring. The methods include determining to execute code corresponding to the first dynamic hardware behavior on a second processing unit, rather than the first processing unit, and scheduling computer program code corresponding to the first dynamic hardware behavior to execute on the second processing unit rather than the first processing unit. Upon completion of execution of the computer code corresponding to the first dynamic hardware behavior, a remaining portion of the computer code is scheduled to execute on the first processing unit.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2021

Methods, media, and systems for detecting attack on a digital processing device

Methods, media, and systems for detecting attack are provided. In some embodiments, the methods include: comparing at least part of a document to a static detection model; determining whether attacking code is included in the document based on the comparison of the document to the static detection model; executing at least part of the document; determining whether attacking code is included in the document based on the execution of the at least part of the document; and if attacking code is determined to be included in the document based on at least one of the comparison of the document to the static detection model and the execution of the at least part of the document, reporting the presence of an attack. In some embodiments, the methods include: selecting a data segment in at least one portion of an electronic document; determining whether the arbitrarily selected data segment can be altered without causing the electronic document to result in an error when processed by a corresponding program; in response to determining that the arbitrarily selected data segment can be altered, arbitrarily altering the data segment in the at least one portion of the electronic document to produce an altered electronic document; and determining whether the corresponding program produces an error state when the altered electronic document is processed by the corresponding program.

Stolfo, Salvatore J.↗