Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “constitutive models”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

Evaluation of Instability Phenomena in Sands: Plane Strain Versus Triaxial Conditions

Extensive research was carried out in the 1950s on theories of plasticity to extend the concepts developed for metals to materials that failed according to the Mohr-Coulomb criterion. The new ideas made it possible to merge the two distinct concepts (strength and deformation techniques) into one that relies on better understanding of plasticity and resulted in a rapid growth in the field of constitutive modeling of soil behavior. At the same time advanced experimental apparatuses and laboratory procedures were developed to calibrate the models. However, most laboratory experiments on granular materials are performed under Conventional Triaxial Conditions (CTC) for the purposes of evaluating constitutive behavior and stability properties, whereas most geotechnical field problems are closer to the Plane Strain (PS) condition. The triaxial tests performed in most laboratories comprise a simplification over in situ states and allow easier and robust experimentation. Most landslide problems, failure of soils beneath shallow and deep foundations, and failure of retaining structures, are cases that can generally be considered as plane strain. Strength and deformation characteristics of granular materials loaded in plane strain may be considerably different from those observed in CTC. Most studies on sands were limited to evaluating the constitutive behavior and in some cases extended to briefly describing the associated instability phenomena. This paper presents the results of a series of PS and CTC experiments performed on fine uniform silica sand known as F-75 Ottawa sand. Advanced analysis techniques were used to study the instability phenomena, which yielded very accurate measurements of shear bands occurrences and patterns. Destructive thin-sectioning technique along with monitoring the specimen surface deformation was used in the PS experiments and Computed Tomography (CT) was used to investigate the progress of primary and secondary shear bands in specimens subjected to CTC. Comparison between the two cases will be presented and discussed.

Alshibli, Khalid A.↗
DOE OSTI2025

DROP DURABILITY ASSESSMENT OF ELECTRONIC ASSEMBLIES UNDER OFF-AXIS LOADING WITH SKEWED FIXTURES

This thesis studies drop durability of electronic assemblies when the acceleration vector is oriented at 45° to the out-of-plane direction of the circuit card. The off-axis drop tests are accomplished with a skewed fixture and are conducted as a proxy for multiaxial drop testing. Advanced shock testing and vibration test methods have been developed over the last few decades to better represent real-world field environments during ground-based laboratory testing. However, many of these test methods require expensive and specialized equipment not available in most laboratories. An alternative approach for approximating simultaneous loading along multiple axes on conventional equipment utilizes skewed fixtures which have seen use in off-axis random vibration and drop impact testing. These methods generally rely on the conversion of a uniaxial input load from the test equipment (using a uniaxial drop tower or shaker) into a multiaxial load when resolved in the reference frame of the test article (mounted on a skewed fixture). Skewed fixture design is presented and recommendations for conducting skewed angle drop testing are introduced based on local measurements along the skewed face of the fixture to accurately monitor the impact event. Characterization tests were performed with a skewed fixture, at simultaneous acceleration loads from 500 to 3,000 g in two (in-plane and out-of-plane) directions, while meeting standard time domain tolerances. Upon experimental characterization, drop shock durability tests were conducted on a printed circuit assembly (PCA). Mean drops-to-failure were measured and quantified with Weibull statistics. Dominant solder joint failure modes were identified via failure analysis. Prior work on inclined angle impact testing is limited, and the majority of solder joint interconnect level fatigue studies are conducted considering perpendicular loading normal the circuit card. Low-cycle fatigue curves are generated based on plastic strain and plastic work density within the solder joint. A multiscale nonlinear finite element model is used to relate board-level flexure to solder joint interconnect level plastic strain. A high strain rate solder constitutive model allows for accurate modeling of solder plasticity resulting from high-impact drop shock. Fatigue parameters are computed from the Coffin-Manson relation and Palmgren-Miner damage accumulation. This work serves to apply established low-cycle fatigue methods for conventional drop shock loading (impact normal to circuit card) to non-perpendicular loading with a skewed fixture.

Hower, Jonathan [Kansas City National Security Cam↗
NASA NTRS1989

Constitutive Relationships and Models in Continuum Theories of Multiphase Flows

In April, 1989, a workshop on constitutive relationships and models in continuum theories of multiphase flows was held at NASA's Marshall Space Flight Center. Topics of constitutive relationships for the partial or per phase stresses, including the concept of solid phase pressure are discussed. Models used for the exchange of mass, momentum, and energy between the phases in a multiphase flow are also discussed. The program, abstracts, and texts of the presentations from the workshop are included.

Decker, Rand↗
DOE OSTI2022

Stress Birth and Death: Disruptive Computational Mechanics and Novel Diagnostics for Fluid-to-Solid Transitions

Many materials of interest to Sandia transition from fluid to solid or have regions of both phases coexisting simultaneously. Currently there are, unfortunately, no material models that can accurately predict this material response. This is relevant to applications that "birth stress" related to geoscience, nuclear safety, manufacturing, energy production and bioscience. Accurately capturing solidification and residual stress enables fully predictive simulations of the evolving front shape or final product. Accurately resolving flow of proppants or blood could reduce environmental impact or lead to better treatments for heart attacks, thrombosis, or aneurism. We will address a science question in this proposal: When does residual stress develop during the critical transition from liquid to solid and how does it affect material deformation? Our hypothesis is that these early phases of stress development are critical to predictive simulation of material performance, net shape, and aging. In this project, we use advanced constitutive models with yield stress to represent both fluid and solid behavior simultaneously. The report provides an abbreviated description of the results from our LDRD "Stress Birth and Death: Disruptive Computational Mechanics and Novel Diagnostics for Fluid-to-Solid Transitions," since we have written four papers that document the work in detail and which we reference. We give highlights of the work and describe the gravitationally driven flow visualization experiment on a model yield stress fluid, Carbopol, at various concentrations and flow rates. We were able to collapse the data on a single master curve by showing it was self-similar. We also describe the Carbopol rheology and the constitutive equations of interest including the Bingham-Carreau-Yasuda model, the Saramito model, and the HB-Saramito model including parameter estimation for the shear and oscillatory rheology. We present several computational models including the 3D moving mesh simulations of both the Saramito models and Bingham-Carreau-Yasuda (BCY) model. We also show results from the BCY model using a 3D level set method and two different ways of handling reduced order Hele-Shaw modeling for generalized Newtonian fluids. We present some first ever two-dimensional results for the modified Jeffries Kamani-Donley-Rogers constitutive equation developed during this project. We include some recent results with a successful Saramito-level set coupling that allows us to tackle problems with complex geometries like mold filling in a thin gap with an obstacle, without the need for remeshing or remapping. We report on some experiments for curing systems where fluorescent particles are used to track material flow. These experiments were carried out in an oven on Sylgard 184 as a model polymerizing system. We conclude the report with a summary of accomplishments and some thoughts on follow-on work.

36 MATERIALS SCIENCE↗
NASA NTRS1997

Micromechanics Analysis Code (MAC) Developed

The ability to accurately predict the thermomechanical deformation response of advanced composite materials continues to play an important role in the development of these strategic materials. Analytical models that predict the effective behavior of composites are used not only by engineers in performing structural analysis of large-scale composite components but also by material scientists in developing new material systems. For an analytical model to fulfill these two distinct functions, it must be based on a micromechanics approach that uses physically based deformation and life constitutive models, and it must allow one to generate the average (macro) response of a composite material given the properties of the individual constituents and their geometric arrangement. Only then can such a model be used by a material scientist to investigate the effect of different deformation mechanisms on the overall response of the composite and, thereby, identify the appropriate constituents for a given application. However, if a micromechanical model is to be used in a large-scale structural analysis it must be (1) computationally efficient, (2) able to generate accurate displacement and stress fields at both the macro and micro level, and (3) compatible with the finite element method. In addition, new advancements in processing and fabrication techniques now make it possible to engineer the architectures of these advanced composite systems. Full utilization of these emerging manufacturing capabilities require the development of a computationally efficient micromechanics analysis tool that can accurately predict the effect of microstructural details on the internal and macroscopic behavior of composites. Computational efficiency is required because (1) a large number of parameters must be varied in the course of engineering (or designing) composite materials and (2) the optimization of a material's microstructure requires that the micromechanics model be integrated with optimization algorithms. From this perspective, analytical approaches that produce closed-form expressions which describe the effect of a material's internal architecture on the overall material behavior are preferable to numerical methods such as the finite element or finite difference schemes.

Source record↗
DOE OSTI2025

Coupled phase field damage and crystal plasticity analysis of intragranular fracture: The role of crystallographic orientation and voids

Damage evolution in engineering metal alloys at the grain scale exhibits significant microstructural heterogeneity and anisotropy. These heterogeneities create local hotspots for stress and strain localization, leading to void nucleation. Crystal orientation influences the active slip systems around voids, affecting lattice rotation and potentially forming discontinuities. At low triaxiality, voids may change shape due to lower stress, rotation, elongation, and coalescence. At high triaxiality, the correlation between crystal orientation and void growth rate becomes stronger, resembling the behavior observed in isolated single crystals. Therefore, understanding the effects of crystal orientation, heterogeneous strain, and defect evolution is crucial for single crystal fracture characterization. Here, in this work, a coupled phase-field damage (PFD) and crystal plasticity (CP) model is implemented within a finite element framework to analyze crystal deformation and failure. The CP method employs a dislocation density-based constitutive model, while intragranular failure is modeled using an anisotropic PFD method. The PFD model considers both the stored energy due to elastic stretching and the energy release due to defect formation and crack formation. A single crystal Al2219 with an intracrystalline spherical void is chosen to analyze fracture. The study finds that fracture propagation is strongly correlated with crystal orientations. This coupled CP-PFD model provides accurate failure prediction in crystalline materials by incorporating the effects of crystal orientations and existing voids. This study demonstrates how the local microstructure and defects influence plastic deformation and failure mechanisms in metal alloys.

Aluminum alloy↗
NASA NTRSDate not supplied

Higher-Order Approximations for Stabilizing Zero-Energy Modes in Peridynamics Crystal Plasticity Models with Large Horizon Interactions

The non-ordinary state-based peridynamics theory combines non-local dynamic techniques with a desirable correspondence material principle, allowing for the use of continuum mechanics constitutive models. Such an approach presents a unique capability for solving problems involving discontinuities (e.g., strain localization, fracture, and fragmentation). However, the correspondence-based peridynamics models often suffer from zero-energy mode instabilities in numerical implementation, primarily due to the approximations of the non-local deformation gradient tensor. This paper focuses on a computational scheme for eliminating the zero-energy mode oscillations using a choice of influence functions that improve the truncation error in a higher-order Taylor series expansion of the deformation gradient. The novelty here is a tensor-based derivation of the linear constraint equations, which can be used to systematically identify the particle interaction weight functions for various user-specified horizon radii. In this paper, the proposed higher-order stabilization scheme is demonstrated for multi-dimensional examples involving polycrystalline and composite microstructures, along with comparisons against conventional finite element methods. The proposed stabilization scheme is shown to be highly effective in suppressing the spurious zero-energy mode oscillations in all numerical examples while enabling efficient simulations of strain localizations across material interfaces.

Non-Ordinary State-Based Peridynamics↗
DOE OSTI2021

A probabilistic creep model incorporating test condition, initial damage, and material property uncertainty

Uncertainty is prevalent in the creep resistance of alloys, where at elevated temperature and low pressure, rupture can range across logarithmic decades. In this study, a probabilistic continuum-damage-mechanics (CDM)-based model is derived to capture the uncertainty of creep resistance. To meet this objective, creep data for alloy 304 Stainless Steel is gathered. A constitutive model, “Sinh”, is calibrated deterministically to determine the statistical variability of the material properties. Three sources of uncertainty are injected into the model: test condition (stress and temperature), initial damage, and material properties. Probabilistic simulations are carried out by (a) calibrating probability distribution functions (pdfs) for each source of uncertainty (b) randomly sampling the pdfs using Monte Carlo methods and (c) executing simulations to replicate the uncertain creep behavior. A sensitivity analysis is performed to evaluate the relative effect of each source of uncertainty. In full probabilistic simulations, the cumulative uncertainty of creep behavior is evaluated. The probabilistic model accurately predicts the creep deformation and rupture of the available experiments. The probabilistic model is validated for interpolation but lacks extrapolation ability. Several future works are proposed to further improve the model.

36 MATERIALS SCIENCE↗
NASA NTRS2023

Prediction of Stiffness and Fatigue Lives of Polymer Matrix Composite Laminates Using Artificial Neural Networks

Machine learning (ML) models are increasingly being used in many engineering fields due to the advancements in ML algorithms and availability of high-speed computing power. One of the most popular ML class of models is artificial neural networks (ANN). ML is increasingly being used in the design and analysis of composite materials and structures, specifically in the constitutive modeling of composite materials with the focus on greatly accelerating multiscale analyses of composite materials and structures through development of surrogate models. Towards that end, both Python and MATLAB-based neural nets have been developed to predict initial stiffness and fatigue life of an eight-ply symmetric polymer matrix composite laminate. Two types of neural networks, a Multilayer Perceptron (MLP) and a Recurrent Neural Network (RNN), have been developed for both platforms. Results show that the both neural net types can provide an excellent estimate of initial stiffness as well as fatigue life of eight-ply symmetric polymer matrix composite laminate. RNNs are better able to capture the shape of the fatigue curve of a laminate. This tool can be very useful for system level studies to obtain an estimate of desired properties and life of PMC composite laminates. The associated surrogate models could also be used in composite multiscale analyses to replace the actual physics-based calculations at lower scales and thereby significantly increase the computational efficiency of such analyses and thus make multiscale analyses a viable industrial tool for large scale structural problems.

Composite↗
NASA NTRSDate not supplied

Stiffness and Fatigue Life Estimator for Polymer Composite Laminates Using Machine Learning

Machine learning (ML) models are increasingly being used in many engineering fields due to the advancements in ML algorithms and availability of high-speed computing power. One of the most popular ML class of models is artificial neural networks (ANN). ML is increasingly being used in the design and analysis of composite materials and structures, specifically in the constitutive modeling of composite materials with the focus on greatly accelerating multiscale analyses of composite materials and structures through development of surrogate models. Towards that end, Python-based neural nets have been developed to predict initial stiffness and fatigue life of an eight-ply symmetric polymer matrix composite laminate. Two types of neural networks, a Multilayer Perceptron (MLP) and a Recurrent Neural Network (RNN), have been established. Results show that both neural net type algorithms can provide an excellent estimate of initial laminate stiffness as well as fatigue life of eight-ply symmetric polymer matrix composite laminates (PMCs). RNNs are better able to capture the shape of the fatigue curve of a laminate. The resulting tool and GUI can be very useful for system level studies to obtain an estimate of desired properties and life of PMC composite laminates. Further, the associated surrogate models can also be used in composite multiscale analyses to replace the actual physics-based calculations at lower scales and thereby significantly increase the computational efficiency of such analyses and thus make micromechanics-based multiscale analyses a viable industrial tool for large scale structural problems.

multiscale analysis↗
NASA NTRS2023

Stiffness and Fatigue Life Estimator for Polymer Composite Laminates Using Machine Learning

Machine learning (ML) models are increasingly being used in many engineering fields due to the advancements in ML algorithms and availability of high-speed computing power. One of the most popular ML class of models is artificial neural networks (ANN). ML is increasingly being used in the design and analysis of composite materials and structures, specifically in the constitutive modeling of composite materials with the focus on greatly accelerating multiscale analyses of composite materials and structures through development of surrogate models. Towards that end, Python-based neural nets have been developed to predict initial stiffness and fatigue life of an eight-ply symmetric polymer matrix composite laminate. Two types of neural networks, a Multilayer Perceptron (MLP) and a Recurrent Neural Network (RNN), have been established. Results show that both neural net type algorithms can provide an excellent estimate of initial laminate stiffness as well as fatigue life of eight-ply symmetric polymer matrix composite laminates (PMCs). RNNs are better able to capture the shape of the fatigue curve of a laminate. The resulting tool and GUI can be very useful for system level studies to obtain an estimate of desired properties and life of PMC composite laminates. Further, the associated surrogate models can also be used in composite multiscale analyses to replace the actual physics-based calculations at lower scales and thereby significantly increase the computational efficiency of such analyses and thus make micromechanics-based multiscale analyses a viable industrial tool for large scale structural problems.

multiscale analysis↗
NASA NTRS1985

Creep crack growth predictions in INCO 718 using a continuum damage model

Creep crack growth tests have been carried out in compact type specimens of INCO 718 at 1200 F (649 C). Theoretical creep crack growth predictions have been carried out by incorporating a unified viscoplastic constitutive model and a continuum damage model into the ARAQUS nonlinear finite element program. Material constants for both the viscoplastic model and the creep continuum damage model were determined from tests carried out on uniaxial bar specimens of INCO 718 at 1200 F (649 C). A comparison of the theoretical creep crack growth rates obtained from the finite element predictions with the experimentally observed creep crack growth rates indicates that the viscoplastic/continuum damage model can be used to successfully predict creep crack growth in compact type specimens using material constants obtained from uniaxial bar specimens of INCO 718 at 1200 F (649 C).

Walker, K. P.↗
NASA NTRS2017

Development of an Input Suite for an Orthotropic Composite Material Model

An orthotropic three-dimensional material model suitable for use in modeling impact tests has been developed that has three major components elastic and inelastic deformations, damage and failure. The material model has been implemented as MAT213 into a special version of LS-DYNA and uses tabulated data obtained from experiments. The prominent features of the constitutive model are illustrated using a widely-used aerospace composite the T800S3900-2B[P2352W-19] BMS8-276 Rev-H-Unitape fiber resin unidirectional composite. The input for the deformation model consists of experimental data from 12 distinct experiments at a known temperature and strain rate: tension and compression along all three principal directions, shear in all three principal planes, and off axis tension or compression tests in all three principal planes, along with other material constants. There are additional input associated with the damage and failure models. The steps in using this model are illustrated composite characterization tests, verification tests and a validation test. The results show that the developed and implemented model is stable and yields acceptably accurate results.

finite element method↗
DOE OSTI2023

SPH modeling of biomass granular flow: Theoretical implementation and experimental validation

The commercialization of biomass-derived energy is impeded by flowability challenges arising from the feeding and handling of granular biomass materials in full-scale biorefineries. To overcome these obstacles, a robust and accurate model to simulate the flow of granular biomass is indispensable. However, conventional mesh-based numerical codes are limited by inherent mesh distortion in simulating large deformation that commonly occurs in granular biomass handling. Here, in this study, we propose a graphics processing unit (GPU)-accelerated meshless Smoothed Particle Hydrodynamics (SPH) code to model the flow of granular biomass materials. A modified void ratio-based mass conversation, a hybrid particle-to-particle/surface frictional boundary treatment, and a hypoplastic constitutive model are implemented. Four numerical examples, an elastic block sliding on inclined planes, sand column collapse, Angle of Repose, and axial compression tests for pine chips, were simulated using the developed SPH code. The results demonstrate good agreement between numerical predictions and analytical and experimental data for all four examples, validating the SPH code and increasing confidence that it can be applied to simulate more complex granular biomass handling processes, such as hopper feeding or auger conveyance.

09 BIOMASS FUELS↗
NASA NTRS1992

Inelastic Deformation of Metal Matrix Composites: Plasticity and Damage Mechanisms - Part 1

The deformation mechanisms of a Ti 15-3/SCS6 (SiC fiber) metal matrix composite (MMC) were investigated using a combination of mechanical measurements and microstructural analysis. The objectives were to evaluate the contributions of plasticity and damage to the overall inelastic response, and to confirm the mechanisms by rigorous microstructural evaluations. The results of room temperature experiments performed on 0 degree and 90 degree systems primarily are reported in this report. Results of experiments performed on other laminate systems and at high temperatures will be provided in a forthcoming report. Inelastic deformation of the 0 degree MMC (fibers parallel to load direction) was dominated by the plasticity of the matrix. In contrast, inelastic deformations of the 90 degree composite (fibers perpendicular to loading direction) occurred by both damage and plasticity. The predictions of a continuum elastic plastic model were compared with experimental data. The model was adequate for predicting the 0 degree response; however, it was inadequate for predicting the 90 degree response largely because it neglected damage. The importance of validating constitutive models using a combination of mechanical measurements and microstructural analysis is pointed out. The deformation mechanisms, and the likely sequence of events associated with the inelastic deformation of MMCs, are indicated in this paper.

Majumdar, B. S.↗
NASA NTRS2005

Comprehensive Micromechanics-Analysis Code - Version 4.0

Version 4.0 of the Micromechanics Analysis Code With Generalized Method of Cells (MAC/GMC) has been developed as an improved means of computational simulation of advanced composite materials. The previous version of MAC/GMC was described in "Comprehensive Micromechanics-Analysis Code" (LEW-16870), NASA Tech Briefs, Vol. 24, No. 6 (June 2000), page 38. To recapitulate: MAC/GMC is a computer program that predicts the elastic and inelastic thermomechanical responses of continuous and discontinuous composite materials with arbitrary internal microstructures and reinforcement shapes. The predictive capability of MAC/GMC rests on a model known as the generalized method of cells (GMC) - a continuum-based model of micromechanics that provides closed-form expressions for the macroscopic response of a composite material in terms of the properties, sizes, shapes, and responses of the individual constituents or phases that make up the material. Enhancements in version 4.0 include a capability for modeling thermomechanically and electromagnetically coupled ("smart") materials; a more-accurate (high-fidelity) version of the GMC; a capability to simulate discontinuous plies within a laminate; additional constitutive models of materials; expanded yield-surface-analysis capabilities; and expanded failure-analysis and life-prediction capabilities on both the microscopic and macroscopic scales.

Arnold, S. M.↗
DOE OSTI2021

A continuum meshfree method for sandbox-style numerical modeling of accretionary and doubly vergent wedges

Here, in this study, we introduce and utilize GEOSPH, a Lagrangian particle-based continuum Smoothed Particle Hydrodynamics (SPH) code to simulate the deformation of geologic materials in sandbox-style experiments using an elastoplastic constitutive model. Due to the meshfree nature of SPH, our proposed framework is capable of handling the large deformations characteristic of sandbox-style experiments. SPH is also able to capture strain localization and discontinuities, allowing us to resolve faulting patterns emerging in the sandbox experiments. We successfully validate our SPH implementation against the benchmark experiments of Buiter and co-workers, and then apply SPH to understand the deformational processes occurring in doubly vergent orogens resultant from the S-point experimental setup and from finitely high wedge-like indenter backstops of different inclinations. We find that the topographic slope of the prowedge results from the competing processes of vertical uplift due to the indenter and forward thrusting, while the topographic slope of the retrowedge is a product of repeated shallow slope failure. Our findings show that SPH is a promising numerical method which should be added to the current palette of computational tools used by structural geologists for solving problems relating to tectonics and crustal deformation.

58 GEOSCIENCES↗