Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “code optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Bringing wings of change - NASA's airfoil research program

A review is presented of progress in attaining technical objectives in three areas of semiautomatic airfoil development: software, hardware, and applications. Software objectives seek improved mathematical models and computer codes for flow analysis and design optimization for a variety of conditions. The 17-step iterative computer model used in designing the GA (W)-1 airfoil is effective but not yet fully automated; with present methods only single-point computer optimization is possible. Hardware objectives calling for improvement in test facilities and techniques are met in part by the introduction of the Langley (F-3C) wind tunnel for independent evaluation of transonic Mach number and Reynolds effects up to 12-16 million, and by a two-dimensional test section for the Langley 1/3 transonic cryogenic tunnel which will extend the Reynolds number to 50 million. The current status of low-speed, thin, and rotorcraft airfoil development programs is discussed.

Pierpont, P. K.↗
NASA NTRS1984

POSTOP: Postbuckled open-stiffener optimum panels-theory and capability

The computer program POSTOP was developed to serve as an aid in the analysis and sizing of stiffened composite panels that are loaded in the postbuckling regime. A comprehensive set of analysis routines was coupled to a widely used optimization program to produce this sizing code. POSTOP is intended for the preliminary design of metal or composite panels with open-section stiffeners, subjected to multiple combined biaxial compression (or tension), shear and normal pressure load cases. Longitudinal compression, however, is assumed to be the dominant loading. Temperature, initial bow eccentricity and load eccentricity effects are included. The panel geometry is assumed to be repetitive over several bays in the longitudinal (stiffener) direction as well as in the transverse direction. Analytical routines are included to compute panel stiffnesses, strains, local and panel buckling loads, and skin/stiffener interface stresses. The resulting program is applicable to stiffened panels as commonly used in fuselage, wing, or empennage structures. The analysis procedures and rationale for the assumptions used therein are described in detail.

Dickson, J. N.↗
NASA NTRS1988

Lewis Structures Technology, 1988. Volume 1: Structural Dynamics

The specific purpose of the symposium was to familiarize the engineering structures community with the depth and range of research performed by the Structures Division of the Lewis Research Center and its academic and industrial partners. Sessions covered vibration control, fracture mechanics, ceramic component reliability, parallel computing, nondestructive testing, dynamical systems, fatigue and damage, wind turbines, hot section technology, structural mechanics codes, computational methods for dynamics, structural optimization, and applications of structural dynamics.

Source record↗
NASA NTRS1999

Performance and Feasibility Analysis of a Wind Turbine Power System for Use on Mars

A wind turbine power system for future missions to the Martian surface was studied for performance and feasibility. A C++ program was developed from existing FORTRAN code to analyze the power capabilities of wind turbines under different environments and design philosophies. Power output, efficiency, torque, thrust, and other performance criteria could be computed given design geometries, atmospheric conditions, and airfoil behavior. After reviewing performance of such a wind turbine, a conceptual system design was modeled to evaluate feasibility. More analysis code was developed to study and optimize the overall structural design. Findings of this preliminary study show that turbine power output on Mars could be as high as several hundred kilowatts. The optimized conceptual design examined here would have a power output of 104 kW, total mass of 1910 kg, and specific power of 54.6 W/kg.

Lichter, Matthew D.↗
NASA NTRS2003

A Nonlinear Model for Fuel Atomization in Spray Combustion

Most gas turbine combustion codes rely on ad-hoc statistical assumptions regarding the outcome of fuel atomization processes. The modeling effort proposed in this project is aimed at developing a realistic model to produce accurate predictions of fuel atomization parameters. The model involves application of the nonlinear stability theory to analyze the instability and subsequent disintegration of the liquid fuel sheet that is produced by fuel injection nozzles in gas turbine combustors. The fuel sheet is atomized into a multiplicity of small drops of large surface area to volume ratio to enhance the evaporation rate and combustion performance. The proposed model will effect predictions of fuel sheet atomization parameters such as drop size, velocity, and orientation as well as sheet penetration depth, breakup time and thickness. These parameters are essential for combustion simulation codes to perform a controlled and optimized design of gas turbine fuel injectors. Optimizing fuel injection processes is crucial to improving combustion efficiency and hence reducing fuel consumption and pollutants emissions.

Liu, Nan-Suey↗
NASA NTRS2001

Arthropod phylogeny based on eight molecular loci and morphology

The interrelationships of major clades within the Arthropoda remain one of the most contentious issues in systematics, which has traditionally been the domain of morphologists. A growing body of DNA sequences and other types of molecular data has revitalized study of arthropod phylogeny and has inspired new considerations of character evolution. Novel hypotheses such as a crustacean-hexapod affinity were based on analyses of single or few genes and limited taxon sampling, but have received recent support from mitochondrial gene order, and eye and brain ultrastructure and neurogenesis. Here we assess relationships within Arthropoda based on a synthesis of all well sampled molecular loci together with a comprehensive data set of morphological, developmental, ultrastructural and gene-order characters. The molecular data include sequences of three nuclear ribosomal genes, three nuclear protein-coding genes, and two mitochondrial genes (one protein coding, one ribosomal). We devised new optimization procedures and constructed a parallel computer cluster with 256 central processing units to analyse molecular data on a scale not previously possible. The optimal 'total evidence' cladogram supports the crustacean-hexapod clade, recognizes pycnogonids as sister to other euarthropods, and indicates monophyly of Myriapoda and Mandibulata.

Non-NASA Center↗
NASA NTRS2006

Entropy Generation/Availability Energy Loss Analysis Inside MIT Gas Spring and "Two Space" Test Rigs

The results of the entropy generation and availability energy loss analysis under conditions of oscillating pressure and oscillating helium gas flow in two Massachusetts Institute of Technology (MIT) test rigs piston-cylinder and piston-cylinder-heat exchanger are presented. Two solution domains, the gas spring (single-space) in the piston-cylinder test rig and the gas spring + heat exchanger (two-space) in the piston-cylinder-heat exchanger test rig are of interest. Sage and CFD-ACE+ commercial numerical codes are used to obtain 1-D and 2-D computer models, respectively, of each of the two solution domains and to simulate the oscillating gas flow and heat transfer effects in these domains. Second law analysis is used to characterize the entropy generation and availability energy losses inside the two solution domains. Internal and external entropy generation and availability energy loss results predicted by Sage and CFD-ACE+ are compared. Thermodynamic loss analysis of simple systems such as the MIT test rigs are often useful to understand some important features of complex pattern forming processes in more complex systems like the Stirling engine. This study is aimed at improving numerical codes for the prediction of thermodynamic losses via the development of a loss post-processor. The incorporation of loss post-processors in Stirling engine numerical codes will facilitate Stirling engine performance optimization. Loss analysis using entropy-generation rates due to heat and fluid flow is a relatively new technique for assessing component performance. It offers a deep insight into the flow phenomena, allows a more exact calculation of losses than is possible with traditional means involving the application of loss correlations and provides an effective tool for improving component and overall system performance.

Ebiana, Asuquo B.↗
NASA NTRS2008

Effect of Adding a Regenerator to Kornhauser's MIT "Two-Space" (Gas-Spring+Heat Exchanger) Test Rig

This study employed entropy-based second law post-processing analysis to characterize the various thermodynamic losses inside a 3-space solution domain (gas spring+heat exchanger+regenerator) operating under conditions of oscillating pressure and oscillating flow. The 3- space solution domain is adapted from the 2-space solution domain (gas spring+heat exchanger) in Kornhauser's MIT test rig by modifying the heat exchanger space to include a porous regenerator system. A thermal nonequilibrium model which assumes that the regenerator porous matrix and gas average temperatures can differ by several degrees at a given axial location and time during the cycle is employed. An important and primary objective of this study is the development and application of a thermodynamic loss post-processor to characterize the major thermodynamic losses inside the 3-space model. It is anticipated that the experience gained from thermodynamic loss analysis of the simple 3-space model can be extrapolated to more complex systems like the Stirling engine. It is hoped that successful development of loss post-processors will facilitate the improvement of the optimization capability of Stirling engine analysis codes through better understanding of the heat transfer and power losses. It is also anticipated that the incorporation of a successful thermal nonequilibrium model of the regenerator in Stirling engine CFD analysis codes, will improve our ability to accurately model Stirling regenerators relative to current multidimensional thermal-equilibrium porous media models.

Ebiana, Asuquo B.↗
NASA NTRS2017

Variable-Depth Liner Evaluation Using Two NASA Flow Ducts

Four liners are investigated experimentally via tests in the NASA Langley Grazing Flow Impedance Tube. These include an axially-segmented liner and three liners that use reordering of the chambers. Chamber reordering is shown to have a strong effect on the axial sound pressure level profiles, but a limited effect on the overall attenuation. It is also shown that bent chambers can be used to reduce the liner depth with minimal effects on the attenuation. A numerical study is also conducted to explore the effects of a planar and three higher-order mode sources based on the NASA Langley Curved Duct Test Rig geometry. A four-segment liner is designed using the NASA Langley CDL code with a Python-based optimizer. Five additional liner designs, four with rearrangements of the first liner segments and one with a redistribution of the individual chambers, are evaluated for each of the four sources. The liner configuration affects the sound pressure level profile much more than the attenuation spectra for the planar and first two higher-order mode sources, but has a much larger effect on the SPL profiles and attenuation spectra for the last higher-order mode source. Overall, axially variable-depth liners offer the potential to provide improved fan noise reduction, regardless of whether the axially variable depths are achieved via a distributed array of chambers (depths vary from chamber to chamber) or a group of zones (groups of chambers for which the depth is constant).

Jones, M. G.↗
NASA NTRS2020

Evaluation of Packing_3D Code for Design of Variable-Depth, Bent-Chamber Acoustic Liners

Increases in the bypass ratio for commercial aircraft engines have caused the broadband fan noise component to become dominant. As a result, there is a need to develop improved acoustic liners suitable for absorption of this fan noise over a wide frequency range, preferably up to at least two octaves. Variable depth liners with bent chambers and three-dimensional geometries present one way to achieve this goal, however, they can be difficult and time-consuming to design due to their complexity and volume constraints. A packing code, called Packing3D, has been developed that automatically designs the chamber configurations of such liners once the chamber dimensions and volume constraints are known. The code uses a randomized trial and error approach to place each chamber in a representation of the liner sample, then returns a colored diagram and sufficient information for the liner sample to be fabricated. For evaluation, the code is used to design four liner samples of varying levels of complexity. These samples are tested with and without a mesh facesheet in the NASA Langley Normal Incidence Tube, and the results are compared to predictions computed in COMSOL. The results indicate that the packing code is able to quickly design samples that are predictable, achieve the desired absorption spectrum, fit the given constraints, and are able to be built. This code is flexible, lends itself to optimization, and allows samples to be designed quickly, accurately, and efficiently.

Marinova, Miroslava M.↗
NASA NTRS2001

EFQPSK Versus CERN: A Comparative Study

This report presents a comparative study on Enhanced Feher's Quadrature Phase Shift Keying (EFQPSK) and Constrained Envelope Root Nyquist (CERN) techniques. These two techniques have been developed in recent times to provide high spectral and power efficiencies under nonlinear amplifier environment. The purpose of this study is to gain insights into these techniques and to help system planners and designers with an appropriate set of guidelines for using these techniques. The comparative study presented in this report relies on effective simulation models and procedures. Therefore, a significant part of this report is devoted to understanding the mathematical and simulation models of the techniques and their set-up procedures. In particular, mathematical models of EFQPSK and CERN, effects of the sampling rate in discrete time signal representation, and modeling of nonlinear amplifiers and predistorters have been considered in detail. The results of this study show that both EFQPSK and CERN signals provide spectrally efficient communications compared to filtered conventional linear modulation techniques when a nonlinear power amplifier is used. However, there are important differences. The spectral efficiency of CERN signals, with a small amount of input backoff, is significantly better than that of EFQPSK signals if the nonlinear amplifier is an ideal clipper. However, to achieve such spectral efficiencies with a practical nonlinear amplifier, CERN processing requires a predistorter which effectively translates the amplifier's characteristics close to those of an ideal clipper. Thus, the spectral performance of CERN signals strongly depends on the predistorter. EFQPSK signals, on the other hand, do not need such predistorters since their spectra are almost unaffected by the nonlinear amplifier, Ibis report discusses several receiver structures for EFQPSK signals. It is observed that optimal receiver structures can be realized for both coded and uncoded EFQPSK signals with not too much increase in computational complexity. When a nonlinear amplifier is used, the bit error rate (BER) performance of the CERN signals with a matched filter receiver is found to be more than one decibel (dB) worse compared to the bit error performance of EFQPSK signals. Although channel coding is found to provide BER performance improvement for both EFQPSK and CERN signals, the performance of EFQPSK signals remains better than that of CERN. Optimal receiver structures for CERN signals with nonlinear equalization is left as a possible future work. Based on the numerical results, it is concluded that, in nonlinear channels, CERN processing leads towards better bandwidth efficiency with a compromise in power efficiency. Hence for bandwidth efficient communications needs, CERN is a good solution provided effective adaptive predistorters can be realized. On the other hand, EFQPSK signals provide a good power efficient solution with a compromise in band width efficiency.

Borah, Deva K.↗
NASA NTRS1985

Transonic rotor tip design using numerical optimization

The aerodynamic design procedure for a new blade tip suitable for operation at transonic speeds is illustrated. For the first time, 3 dimensional numerical optimization was applied to rotor tip design, using the recent derivative of the ROT22 code, program R22OPT. Program R22OPT utilized an efficient quasi-Newton optimization algorithm. Multiple design objectives were specified. The delocalization of the shock wave was to be eliminated in forward flight for an advance ratio of 0.41 and a tip Mach number of 0.92 at psi = 90 deg. Simultaneously, it was sought to reduce torque requirements while maintaining effective restoring pitching moments. Only the outer 10 percent of the blade span was modified; the blade area was not to be reduced by more than 3 percent. The goal was to combine the advantages of both sweptback and sweptforward blade tips. A planform that featured inboard sweepback was combined with a sweptforward tip and a taper ratio of 0.5. Initially, the ROT22 code was used to find by trial and error a planform geometry which met the design goals. This configuration had an inboard section with a leading edge sweep of 20 deg and a tip section swept forward at 25 deg; in addition, the airfoils were modified.

Tauber, Michael E.↗
NASA NTRS1993

On the optimality of a universal noiseless coder

Rice developed a universal noiseless coding structure that provides efficient performance over an extremely broad range of source entropy. This is accomplished by adaptively selecting the best of several easily implemented variable length coding algorithms. Variations of such noiseless coders have been used in many NASA applications. Custom VLSI coder and decoder modules capable of processing over 50 million samples per second have been fabricated and tested. In this study, the first of the code options used in this module development is shown to be equivalent to a class of Huffman code under the Humblet condition, for source symbol sets having a Laplacian distribution. Except for the default option, other options are shown to be equivalent to the Huffman codes of a modified Laplacian symbol set, at specified symbol entropy values. Simulation results are obtained on actual aerial imagery over a wide entropy range, and they confirm the optimality of the scheme. Comparison with other known techniques are performed on several widely used images and the results further validate the coder's optimality.

Yeh, Pen-Shu↗
NASA NTRS2018

Optimization of Elastodynamic Finite Integration Technique on Intel Xeon Phi Knights Landing Processors

This work describes the development and optimization of an implementation of an isotropic elastodynamic finite integration technique (EFIT) code for parallelized computation on Intel Knights Landing (KNL) hardware. EFIT is a numerical approach resulting in standard staggered-grid finite difference equations for the elastodynamic equations of motion to simulate bulk waves is solids. The computationally efficient simulation of elastodynamic wave propagation and interactions in aerospace materials is of high-interest in the fields of nondestructive evaluation (NDE) and structural health monitoring (SHM). Ultrasonic inspection uses an ultrasonic signal, generated at the surface of the material/structure via use of a piezoelectric transducer, to propagate sound waves into the material where it interacts with any existing defects, as well as with structural boundaries and any material inhomogeneity. Reflections from defects and boundaries are then measured by a transducer. Realistic ultrasound simulation tools can significantly aid the development and optimization of inspection techniques and can assist in the interpretation of experimental data. The optimization of an elastodynamics simulation code for the KNL Many Integrated Core processor was performed. The optimization focused on data locality and vectorization. Results show that tiling of the data to exploit the cache behavior and allow for significant utilization of the KNL hardware. The MPI implementation allows for a scalable implementation enabling large problems to be simulated. The model results were validated against theoretical dispersion curves to within 2% of the group velocity, and within 0.5% of the phase velocity of the A0 mode. Aggressive use of tiling, threading, and vectorization techniques allowed for dramatically improved time to solution.

William C. Schneck↗
NASA NTRS2018

Automation of Structural Sizing of Aircraft Concepts Under Static Aeroelastic Constraints

This paper presents an automation process for structural sizing of subsonic and supersonic aircraft concepts under static aeroelastic constraints. The automation process starts with an OpenVSP geometry and ends with a PATRAN plot of a NASTRAN solution for static aeroelastic analysis or optimization. ModelCenter is used to integrate all analysis codes with easy-to-use interfaces. Automation tools are developed to streamline the setup process and avoid user errors. Fuel is distributed by solving an optimization problem to match the center of gravity of aircraft at a specified flight condition. Fuel weights are also automatically attached to the structural model as point masses. All other weights used in FLOPS mission analysis (excluding fuselage and wing structural weights) are automatically attached to or smeared on the structural model. For any given OpenVSP geometry and FLOPS analysis data, a static aeroelastic sizing model for NASTRAN analysis can be generated in a couple of hours. The empirical fuselage and wing structural weights from FLOPS are replaced by structural panel weights from the sized finite-element model. Three supersonic and two subsonic aircraft concepts are used to demonstrate the automation process as a physics-based weight estimation tool for aircraft conceptual design.

Li, Wu↗
NASA NTRS1992

Aerodynamic design of axisymmetric hypersonic wind-tunnel nozzles using least-squares/parabolized Navier-Stokes procedure

A new procedure unifying the best of present classical design practices, CFD and optimization procedures, is demonstrated for designing the aerodynamic lines of hypersonic wind tunnel nozzles. This procedure can be employed to design hypersonic wind tunnel nozzles with thick boundary layers where the classical design procedure has been demonstrated to break down. Advantages of this procedure allow full utilization of powerful CFD codes in the design process, solves an optimization problem to determine the new contour, may be used to design new nozzles or improve sections of existing nozzles, and automatically compensates the nozzle contour for viscous effects as part of the unified design procedure.

Korte, John J.↗
NASA NTRS1996

Minimum Heating Re-Entry Trajectories for Advanced Hypersonic Launch Vehicles

Optimal re-entry trajectories are generated for reusable launch vehicles which minimize: (1) the heat absorbed at the vehicle surface, (2) the lower surface temperature, and (3) the heat absorbed by the internal structure. The approach uses the energy state approximation technique and a finite control volume heat transfer code coupled to a flight path integration code. These trajectories are compared to the optimal re-entry trajectory minimizing the integrated convective heat rate to determine which trajectory produces the minimum internal structural temperatures for a given thermal protection system. Three different thermal protection systems are considered: tile, blanket, and metallic.

Robert Windhorst↗
NASA NTRS1992

Navier-Stokes computations of a viscous optimized waverider

The performance of a Mach 6 viscous optimized waverider was calculated using the 3-D Navier-Stokes equations. The Mach 6 viscous optimized waverider was generated using MAXWARP, a code developed at the University of Maryland. The computations were performed using CFL3D, an implicit upwind-biased finite-volume algorithm developed at NASA Langley. Results show that good agreement was found between the calculated performance by MAXWARP and results from the Mach 6 Navier-Stokes computation. Furthermore, off-design performance of the Mach 6 optimized waverider was computed at Mach 4 and 8. The performance at these Mach numbers compared well with the performance of the viscous optimized waveriders specifically designed for these Mach numbers. Finally, contours of different flow parameters in the cross-flow plane were examined for the three calculations. The results indicate that the flow gradients are relatively small within the captured flow, and the variation itself is well behaved; thus, making the waverider configuration a promising choice for an engine/airframe design, especially for cruise-type applications.

Takashima, Naruhisa↗