SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Application of Polyurethane Science and Engineering to reduce ALARA conditions while securing Low Level Waste (LLW) loads for shipment within and between locations within the DOE complex. Potential reduction in cost as well. Interdepartmental collaborative efforts between new hires was established.
SUMMARY A pair of 1-ton, conventional surface explosions were conducted at the Nevada National Security Site in the fall of 2020 producing seismoacoustic signatures observable hundreds of kilometres from the source location. Regional infrasonic observations include tropospheric ducting at large distances to the south, a wide stratospheric waveguide with signals observed more than 700 km to the east, and anomalous arrivals in the stratospheric shadow zone. Notable differences in propagation between the events are identified despite the explosions being conducted just two days apart due to a sharp temporal shift in the tropospheric winds as well as structural changes in the stratospheric winds. Propagation simulations of the two events have been completed using a combination of ray tracing and parabolic equation (PE) methods. Simulations have been conducted to quantify the impact of the temporal variations in the atmosphere as well as the influence of terrain on propagation. Temporal variations in reflection locations are found to produce notable changes in downrange propagation due to spatially varying terrain features. Finite frequency effects modelled by the PE are found to predict ensonification not included in corresponding 2D ray tracing simulations. Notable variations in predicted signal amplitude are found due to focusing by along-path and cross-path terrain gradients; though, the later of these is only modelled using fully 3D ray tracing analysis.
A traditional safeguards neutron coincidence counting system, the Neutron Coincidence Collar, has been modified to incorporate individual preamplifiers on each of its 18 3He tubes in active interrogation mode. When used with list mode data acquisition (LMDA) and analysis, a signal from each 3He tube can be recorded and analyzed to allow a spatial response measurement to be performed on an item based on count rate and 3He tube location within the system. The ultimate goal of this project is to demonstrate the capabilities of a list mode response matrix for the nondestructive assay of fresh nuclear fuel assemblies. To enable partial defect detection of fuel pin locations and absences within an assembly, the project aims to extend well-established correlated neutron analysis techniques on a preexisting Neutron Coincidence Collar by extracting a greater number of useful signatures from the system than are currently generated. LMDA, combined with the addition of multiple preamplifiers, facilitates this capability by increasing the number of simultaneous signals that can be measured; this allows an in-depth analysis of neutron coincidence events to determine a fissioning item’s location based on the measured doubles count rate in various channel logic coincidence combinations. All of this can be done from a single measurement pulse train in offline analysis, which is the major benefit provided by LMDA. Through various stages of development and testing, a Mirion Technologies model JCC-71 Neutron Coincidence Collar has been successfully retrofit with modern electronics designed in-house at Oak Ridge National Laboratory, matching preexisting JAB-01 electronics performance, while maintaining the original system footprint. This paper presents these various stages of development and experimental evaluation of the proof of concept system.
Distributed acoustic sensing (DAS) was originally intended to measure oscillatory strain at frequencies of 1 Hz or more on a fiber optic cable. Recently, measurements at much lower frequencies have opened the possibility of using DAS as a dynamic strain sensor in boreholes. A fiber optic cable mechanically coupled to a geologic formation will strain in response to hydraulic stresses in pores and fractures. A DAS interrogator can measure dynamic strain in the borehole, which can be related to fluid pressure through the mechanical compliance properties of the formation. Because DAS makes distributed measurements, it is capable of both locating hydraulically active features and quantifying the fluid pressure in the formation. We present field experiments in which a fiber optic cable was mechanically coupled to two crystalline rock boreholes. The formation was stressed hydraulically at another well using alternating injection and pumping. The DAS instrument measured oscillating strain at the location of a fracture zone known to be hydraulically active. Rock displacements of less than 1 nm were measured. Laboratory experiments confirm that displacement is measured correctly. These results suggest that fiber optic cable embedded in geologic formations may be used to map hydraulic connections in three-dimensional fracture networks. A great advantage of this approach is that strain, an indirect measure of hydraulic stress, can be measured without beforehand knowledge of flowing fractures that intersect boreholes. The technology has obvious applications in water resources, geothermal energy, CO 2 sequestration, and remediation of groundwater in fractured bedrock.
The Pacific Northwest National Laboratory (PNNL) 3420 Building, which is part of the Physical Sciences Facility (PSF), houses radiological capabilities that results in the requirement that emissions monitoring must be conducted for potential radionuclides in the exhaust air discharge of this building. The air monitoring system is required to conform to Title 40 of the Code of Federal Regulations part 61 (40 CFR 61) Subpart H, which in turns requires a sampling probe in the exhaust stream to conform to the criteria of American National Standards Institute / Health Physics Society (ANSI/HPS) N13.1-2011, Sampling and Monitoring Releases of Airborne Radioactive Substances from the Stack and Ducts of Nuclear Facilities. To support the air emissions permit for the 3420 Building on the PNNL campus, stack testing that used computational fluid dynamics (CFD) modeling as a surrogate stack and verification tests of velocity uniformity and flow angle on the retrofitted facility stack was performed. The ANSI/HPS N13.1-2011 criteria for the air monitoring probe location are that velocity uniformity, gaseous tracer uniformity, and particulate tracer uniformity must be less than or equal to 20%COV. Furthermore, no point in the sampling location may have a gaseous tracer concentration that varies from the mean concentration by more than 30%. Additionally, the flow angle at the sampling location must not be more than 20°. The CFD modeling of the stack, as reported by Recknagle et al. (2018) demonstrated that the stack meets the criteria at the probe location. The velocity uniformity and flow angle results from the 3420 stack verification tests, performed in October 2020, demonstrated that the CFD model results may be used to support the qualification of the stack sampling location. The measured velocity uniformity verification test result was 1.4%COV. This value is well within the uniformity criterion, which is that the velocity uniformity be =20%COV. Additionally, this value is well within the criterion that the actual stack measurement must be within 5% of the surrogate stack result of 2.1%COV when all four fans were operating. Additionally, the measured average flow angle at the 3420 stack monitor location was 15.5 degrees. Although this is higher than expected based on the CFD model, the result is =20 degrees, so the criterion is met. Based on these stack verification test results, the reconfigured 3420 Building filtered exhaust stack meets the qualification criteria given in the ANSI/HPS N13.1-2011 standard. Further changes to the system configuration or operating conditions that are outside the bounds described in this and the CFD report (Recknagle et al., 2018) may require additional tests and additional analysis to determine compliance with the standard.
Ac transmission protection must reliably detect, classify, and locate short-circuit faults from voltage and current measurements. At present, these functionalities, which have been classically engineered using phasors approaches, are being challenged by the dynamic behavior and fault-current limits of converter-based generation. This paper tackles these challenges by engineering a time-domain protection approach that leverages the classical Bergeron model in a new manner. Low- and high-impedance faults are detected and classified by ascertaining how well line voltage and current measurements match the Bergeron equations. Faults are located by posing a novel one-variable optimization problem, whereas voltage and current waveforms at the fault location are estimated by unveiling rigorous relationships. The proposed elements are secure against external faults, measurement errors, and variation of line parameters and sampling time. Furthermore, these advances are tested via electromagnetic transient simulations and are significant to satisfy IEEE and North American Electric Reliability Corporation requirements.
Discovery of high-efficiency water-splitting catalysts is critical for clean hydrogen fuel generation. Quantitative and reliable chemical imaging methods can play a crucial role in providing critical catalyst efficiency information for materials development and screening. Here, we developed a reflection optical imaging method to map the performance of transition metal oxide catalysts for oxygen evolution reaction (OER). The generated high concentration of oxygen in the electrolyte will decrease the refractive index of the solutions near the electrode and change the reflectivity of optical images. We successfully imaged and measured the OER on cobalt oxide, and the localized current density and overpotential distribution maps have been extracted. The oxidation and reduction of cobalt oxide can be imaged with our reflection optical imaging method as well. These maps showed that the catalytic activities are quite different at different locations, and some regions showed much higher activities. This is due to the non-uniformity created by the catalyst synthesis process and demonstrates the importance of using the optical imaging method to map the localized catalytic efficiency. In addition, the NiFe alloy’s OER catalytic activities have been studied as well. The proposed reflection optical imaging method could find many applications in catalyst activity measurement and screening.
We present observations and modeling of spatial eigen-functions of resonating waves within fault zone waveguide, using data recorded on a dense seismic array across the San Jacinto Fault Zone (SJFZ) in southern California. The array consists of 5-Hz geophones that cross the SJFZ with ~10-30 m spacing at the Blackburn Saddle near the Hemet Stepover. Wavefield snapshots after the S wave arrival are consistent for more than 50 near-fault events, suggesting that this pattern is controlled by the fault zone structure rather than source properties. Data from example event with high signal to noise ratio shows three main frequency peaks at ~1.3 Hz, ~2.0 Hz, and ~2.8 Hz in the amplitude spectra of resonance waves averaged over stations near the fault. The data are modeled with analytical expressions for eigen-functions of resonance waves in a low-velocity layer (fault zone) between two quarter-spaces. Using a grid search-based method, we investigate the possible width of the waveguide, location within the array, and shear wave velocities of the media that fit well the resonance signal at ~1.3 Hz. The results indicate a ~300 m wide damaged fault zone layer with ~65% S wave velocity reduction compared to the host rock. The SW edge of the low-velocity zone is near the mapped fault surface trace, indicating that the damage zone is asymmetrically located at the regionally faster NE crustal block. The imaging resolution of the fault zone structure can be improved by modeling fault zone resonance modes and trapped waves together.
The Raton Basin of Southern Colorado and Northern New Mexico experienced a significant increase in seismicity over the last several decades, including two M5+ earthquakes. The increase in seismicity started soon after an increase in wastewater disposal associated with coal-bed methane production. Twenty-nine wastewater injection wells have operated in the Basin, with several high-rate injectors located within a kilometer of the most seismically active regions. We developed a pore pressure model to investigate the relationship between pore pressure diffusion and onset of induced seismicity, with an emphasis on the Trinidad fault zones. Our model indicates that sufficient pore pressure increase had accumulated on the northern extent of the Trinidad fault zone to induce seismicity at the time of early-stage seismic activity. The hydrogeologic architecture of the Basin played a key role in controlling pore pressure perturbation. The basal sedimentary interval with moderately low diffusivity restricted vertical pore pressure diffusion, creating a substantial lag time between wells becoming active and the expression of perturbation in the fault zones. The spatiotemporal relationship between early-stage seismicity and wastewater injection in conjunction with modeled pore pressures suggests that the early-stage seismicity in the Raton Basin was likely triggered by pore pressure diffusion.
Alkaline pretreatment can depolymerize lignin into a diverse mixture of monomers and smaller compounds, enabling bioconversion of these compounds to value-added chemicals in engineered bacterial hosts such as Pseudomonas putida KT2440. Acetate and salts comprise approximately 8% and 32% of the lignin stream, respectively. High concentrations of these components can cause cell death in P. putida, so lignin-derived streams must be fed in lower amounts to decrease stress. Investigation of the mechanisms of bacterial tolerance to chemicals in lignin-rich substrates is therefore required to overcome this obstacle in lignin bioconversion. Previous work has shown that trehalose, an endogenously produced disaccharide, is involved in tolerance to heat, cold, and osmotic stress, as well as implicated in acid stress in other bacteria. As such, trehalose biosynthesis presents a useful target to increase acetate and osmotic tolerance in P. putida. This work investigates the native TreSA, TreSB, and TreY/TreZ trehalose biosynthesis pathways in this bacterial strain as well as the OtsAB pathway of Sphingobium sp. SYK-6. Overexpression of the OtsAB pathway in P. putida increased tolerance to acetate relative to wild-type. Additionally, functional knockouts of treSA, treSB, treY, and treZ in P. putida showed that interruption of any trehalose biosynthesis pathway, and, in the case of TreY/TreZ, interruption of the pathway at any point, significantly hindered growth in acetate as well as on glucose and LB broth. Each trehalose biosynthesis pathway was then engineered for overexpression in P. putida to determine whether overexpression of these genes conferred additional tolerance to acetate. The TreSA, TreSB, OtsA, and OtsB enzymes were also expressed and purified to determine the reaction rates and kinetics of these pathways. The hypothetical glycoside hydrolase family 15 protein, encoded in the gene located in between otsB and otsA in the Sphingobium operon, was purified as well to investigate its potential involvement in the OtsAB pathway. The findings of this work illuminated the mechanisms of trehalose biosynthesis in P. putida and identified genetic targets to improve strain tolerance to common components of alkaline-pretreated lignin streams. These findings could ultimately improve yields of desired products from lignin in engineered strains of P. putida.
The Long Wavelength Array is a radio telescope array located at the Sevilleta National Wildlife Refuge in La Joya, New Mexico, well suited and situated for the observation of lightning. The array consists of 256 high-sensitivity dual polarization antennas arranged in a 100 m diameter. This paper demonstrates some of the capabilities that the array brings to the study of lightning. Once 32 or more antennas are used to image lightning radio sources, virtually every integration period longer than the impulse response of the array includes at least one identifiable lightning emitter, independent of the integration period used. The use of many antennas also allows multiple simultaneous lightning radio sources to be imaged at sub-microsecond timescales; for the flash examined, 51% of the images contained more than one lightning source. Finally, by using many antennas to image lightning sources, the array is capable of locating sources fainter than the galactic background radio noise level, yielding possibly the most sensitive radio maps of lightning to date. This incredible sensitivity enables, for the first time, the emissions originating from the positive leader tips of natural in-cloud lightning to be detected and located. The tip emission is distinctly different from needle emission and is most likely due to positive breakdown.
Abstract Hatchery production of Chinook Salmon Oncorhynchus tshawytscha in the Columbia River basin comprises most of the anadromous salmonid production in this region. Hatchery facilities and programs serve to mitigate for impacts to salmonids due to the construction and operation of hydropower dams and habitat impacts from development in addition to the conservation and restoration of natural populations. A genetic method referred to as parentage-based tagging (PBT) enables highly reliable detection of hatchery-origin fish and inference of multigeneration pedigrees. This study compiles 11 years of PBT data from nearly 125,000 interior stream-type Chinook Salmon from 24 spawning hatcheries located in tributaries of the mid- and upper Columbia River as well as the Salmon, Clearwater, and Grande Ronde River subbasins. Multigenerational pedigrees allowed investigation of the proportion of natural- and hatchery-origin broodstock (pNOB and pHOB, respectively) for each hatchery and enumeration of the scale of production between segregated and integrated programs. We then compared how pHOB and the scale of production influenced the number of stray fish observed, genetic diversity, relatedness, and age-class compositions within broodstocks. Over 91.0% of hatchery broodstock could be assigned back to their parents, and there was an overall rate of less than 1.0% of broodstock that were unintentionally incorporated into nonnatal hatchery programs. We evaluated 14 segregated programs with 0.0–10.0% pNOB, 7 intermediate programs (10.1–50.0% pNOB), and 3 integrated programs (>50.0% pNOB). There was no correlation between the scale of production or pNOB with the level of genetic diversity, but as production size increased, so did the effective number of breeders. This study demonstrates the utility of PBT as a monitoring tool for hatchery broodstocks, and results suggest that segregated and integrated programs have tradeoffs that generally align with their intended broodstock management purpose of providing fish for harvest and/or fish for supplementation or reintroduction.
Techno-economic analyses (TEAs) and life cycle assessments (LCAs) of algal biofuels often focus on locations in suboptimal latitudes for algal cultivation, which can under-represent the sustainability potential of the technology. This study identifies the optimal global productivity potential, environmental impacts, and economic viability of algal biofuels by using validated biophysical and sustainability modeling. The biophysical model simulates growth rates of Scenedesmus obliquusbased on temperature, photoinhibition, and respiration effects at 6685 global locations. Region-specific labor costs, construction factors, and tax rates allow for spatially resolved TEA, while the LCA includes regional impacts of electricity, hydrogen, and nutrient markets across ten environmental categories. The analysis identifies optimal locations for algal biofuel production in terms of environmental impacts and economic viability which are shown to follow biomass yields. Modeling results highlight the global variability of productivity with maximum yields ranging between 24.8 and 27.5 g m -2 d -1 in equatorial regions. Environmental impact results show favorable locations tracked with low-carbon electricity grids, with the well-to-wheels global warming potential (GWP) ranging from 31 to 45 g CO 2eq MJ -1 in South America and Central Africa. When including direct land use change impacts, the GWP ranged between 44 and 55 g CO 2eq MJ -1 in these high-productivity regions. Low-carbon electricity also favors air quality and eutrophication impacts. The TEA shows that minimum algal fuel prices of $\$1.89$-$\$2.15$ per liter of gasoline-equivalent are possible in southeast Asia and Venezuela. Furthermore, this discussion focuses on the challenges and opportunities to reduce fuel prices and the environmental impacts of algal biofuels in various global regions.
We use the POLARIS radiative transfer code to produce simulated circular polarization Zeeman emission maps of the cyanide (CN) J = 1–0 molecular line transition for two types of protostellar envelope magnetohydrodynamic simulations. Our first model is a low-mass disc envelope system (box length L = 200 au), and our second model is the envelope of a massive protostar (L = 104 au) with a protostellar wind and a CN-enhanced outflow shell. We compute the velocity-integrated Stokes I and V, as well as the implied V/I polarization percentage, for each detector pixel location in our simulated emission maps. Our results show that both types of protostellar environments are in principle accessible with current circular polarization instruments, with each containing swaths of envelope area that yield percentage polarizations that exceed the 1.8 percent nominal sensitivity limit for circular polarization experiments with the Atacama Large Millimeter/submillimeter Array. In both systems, high-polarization (≳1.8 percent) pixels tend to lie at an intermediate distance away from the central star and where the line-centre opacity of the CN emission is moderately optically thin (τLC ~ 0.1–1). Furthermore, our computed V/I values scale roughly with the density-weighted mean line-of-sight magnetic field strength, indicating that Zeeman observations can effectively diagnose the strength of envelope-scale magnetic fields. We also find that pixels with large V/I are preferentially co-located where the absolute value of the velocity-integrated V is also large, suggesting that locations with favourable percentage polarization are also favourable in terms of raw signal.
To prepare for its third phase, the Hawaii Play Fairway project conducted groundwater sampling and analyses in ten locations in the Hawaiian islands, magnetotelluric (MT) and gravity surveys, as well as calculations of 3D subsurface stress due to the weight of the rock underlying the topography of the volcano. The subsurface stresses were used to evaluate the potential for fracture-induced permeability. Inversions of the MT and gravity data produce 3D models of resistivity and density, respectively, on Lanai, across Haleakala's SW rift (Maui), and surrounding Mauna Kea (Hawaii Island). The project developed and applied a new method for incorporating depth information about resistivity, density, and potential for fracture-induced permeability into the statistical method for computing resource probability in these three focus areas. The project then incorporated the new groundwater results with the new geophysical results and the calculations of potential for fracture-induced permeability to produce updated maps of resource probability and confidence. These results were used to identify target sites for exploratory drilling. Spreadsheet information: Each sheet contains data for a particular depth in kilometers. Positive depths are above sea level, and negative below. For more information, go to the Hawaii Groundwater and Geothermal Resources Center website linked in the resources.
Waveform modeling is crucial to improving our understanding of observed seismograms. Forward simulation of wavefields provides quantitative methods of testing interactions between complicated source functions and the propagation medium. Here, we discuss three experiments designed to improve under standing of high frequency seismic wave propagation. First, we compare observed and predicted travel times of crustal phases for a set of real observed earthquakes with calculations and synthetic seismograms. Second, we estimate the frequency content of a series of nearly co-located earthquakes of varying magnitude for which we have a relatively well- known 1D velocity model. Third, we apply stochastic perturbations on top of a 3D tomographic model and qualitatively assess how those variations map to differences in the seismograms. While different in scope and aim, these three vignettes illustrate the current state of crustal scale waveform modeling and the potential for future studies to better constrain the structure of the crust.
A diverse portfolio of carbon dioxide removal (CDR) technologies will be essential to meeting climate goals while supporting sustainable development. In particular, marine carbon dioxide removal (mCDR) methods can help diversify the existing portfolio, which currently relies heavily on engineered direct air capture systems for large-scale atmospheric removals. To fulfill their potential in the CDR ecosystem, these early-stage mCDR technologies require additional research and development. Here, we propose regional mCDR Technology Centers of Excellence that will provide inventors and developers with access to right-scale facilities and engineering expertise that will meet their needs wherever they are on the journey from bench- to pilot-scale development. To support innovation across the technological readiness level spectrum, these Centers will provide collaborative access to ocean-based mCDR testing sites; other opportunities for partnering with multidisciplinary experts in technology development and commercialization; provide meaningful pathways for integrated engagement with local industrial and regulatory systems; and help in developing tailored, impactful community benefit models. Ideal sites are co-located in areas with a favorable natural environment for testing mCDR, well studied baselines, accessible infrastructure for multidisciplinary marine research, and technology commercialization support. As a case study, we offer the Pacific Northwest as particularly suitable for a regional mCDR Technology Center of Excellence given existing and potential growth of all the characteristics of ideal sites listed above, and which could especially benefit from the region’s growing marine climate technology sector. Last, we offer a brief whole-of-government perspective for supporting and regulating these Centers of Excellence, including identification of mCDR Science Centers of Excellence to ensure that the development of mCDR technologies dovetails with much-needed advancements in oceanographic observation and simulation infrastructure.
This report presents analysis of high-temporal-resolution whole-house electrical consumption data obtained from 17 residential buildings located in the Denver metro and Aspen regions of Colorado as well as survey data collected from the participants related to building characteristics and equipment types.