Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Turbulence Stabilization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

The influence of sweep on the aerodynamic loading of an oscillating NACA 0012 airfoil. Volume 1: Technical report

Aerodynamic experiments were performed on an oscillating NACA 0012 airfoil utilizing a tunnel-spanning wing in both unswept and 30 degree swept configurations. The airfoil was tested in steady state and in oscillatory pitch about the quarter chord. The unsteady aerodynamic loading was measured using pressure transducers along the chord. Numerical integrations of the unsteady pressure transducer responses were used to compute the normal force, chord force, and moment components of the induced loading. The effects of sweep on the induced aerodynamic load response was examined. For the range of parameters tested, it was found that sweeping the airfoil tends to delay the onset of dynamic stall. Sweeping was also found to reduce the magnitude of the unsteady load variation about the mean response. It was determined that at mean incidence angles greater than 9 degrees, sweep tends to reduce the stability margin of the NACA 0012 airfoil; however, for all cases tested, the airfoil was found to be stable in pure pitch. Turbulent eddies were found to convect downstream above the upper surface and generate forward-moving acoustic waves at the trailing edge which move upstream along the lower surface.

St.hilaire, A. O.↗
NASA NTRS1989

Recent advances in engineering science; Proceedings of the A. Cemal Eringen Symposium, University of California, Berkeley, June 20-22, 1988

Various papers on recent advances in engineering science are presented. Some individual topics addressed include: advances in adaptive methods in computational fluid mechanics, mixtures of two medicomorphic materials, computer tests of rubber elasticity, shear bands in isotropic micropolar elastic materials, nonlinear surface wave and resonator effects in magnetostrictive crystals, simulation of electrically enhanced fibrous filtration, plasticity theory of granular materials, dynamics of viscoelastic media with internal oscillators, postcritical behavior of a cantilever bar, boundary value problems in nonlocal elasticity, stability of flexible structures with random parameters, electromagnetic tornadoes in earth's ionosphere and magnetosphere, helicity fluctuations and the energy cascade in turbulence, mechanics of interfacial zones in bonded materials, propagation of a normal shock in a varying area duct, analytical mechanics of fracture and fatigue.

Koh, Severino L.↗
NASA NTRS2003

Characterization of High-Frequency Excitation of a Wake by Simulation

Insights into the effects of high-frequency forcing on free shear layer evolution are gained through analysis of several direct numerical simulations. High-frequency forcing of a fully turbulent plane wake results in only a weak transient effect. On the other hand, significant changes in the developed turbulent state may result when high-frequency forcing is applied to a transitional wake. The impacts of varying the characteristics of the high-frequency forcing are examined, particularly, the streamwise wavenumber band in which forcing is applied and the initial amplitude of the forcing. The high-frequency excitation is found to increase the dissipation rate of turbulent kinetic energy, to reduce the turbulent kinetic energy production rate, and to reduce the turbulent kinetic energy suppression increases with forcing amplitude once a threshold level has been reached. For a given initial forcing energy, the largest reduction in turbulent kinetic energy density was achieved by forcing wavenumbers that are about two to three times the neutral wavenumber determined from linear stability theory.

Cain, Alan B.↗
NASA NTRS2007

Technical Findings, Lessons Learned, and Recommendations Resulting from the Helios Prototype Vehicle Mishap

The Helios Prototype was originally planned to be two separate vehicles, but because of resource limitations only one vehicle was developed to demonstrate two missions. The vehicle consisted of two configurations, one for each mission. One configuration, designated HP01, was designed to operate at extremely high altitudes using batteries and high-efficiency solar cells spread across the upper surface of its 247-foot wingspan. On August 13, 2001, the HP01 configuration reached an altitude of 96,863 feet, a world record for sustained horizontal flight by a winged aircraft. The other configuration, designated HP03, was designed for long-duration flight. The plan was to use the solar cells to power the vehicle's electric motors and subsystems during the day and to use a modified commercial hydrogen-air fuel cell system for use during the night. The aircraft design used wing dihedral, engine power, elevator control surfaces, and a stability augmentation and control system to provide aerodynamic stability and control. At about 30 minutes into the second flight of HP03, the aircraft encountered a disturbance in the way of turbulence and morphed into an unexpected, persistent, high dihedral configuration. As a result of the persistent high dihedral, the aircraft became unstable in a very divergent pitch mode in which the airspeed excursions from the nominal flight speed about doubled every cycle of the oscillation. The aircraft s design airspeed was subsequently exceeded and the resulting high dynamic pressures caused the wing leading edge secondary structure on the outer wing panels to fail and the solar cells and skin on the upper surface of the wing to rip away. As a result, the vehicle lost its ability to maintain lift, fell into the Pacific Ocean within the confines of the U.S. Navy's Pacific Missile Range Facility, and was destroyed. This paper describes the mishap and its causes, and presents the technical recommendations and lessons learned for improving the design, analysis, and testing methods and techniques required for this class of vehicle.

Noll, Thomas E.↗
NASA NTRSDate not supplied

Verification of Anisotropic Mesh Adaptation for Complex Aerospace Applications

The stabilized finite element solver, FUN3D-SFE, along with the grid mechanics package refine are verified for aerospace applications of laminar and turbulent flow simulations. The current verification exercise represents an extension of previous research using FUN3D-SFEwith adjoint-based mesh adaptation to generate highly anisotropic adapted meshes for inviscid problems. Adaptations are performed using a solution-based approach that controls the Lpnorm of Mach number interpolation error and an adjoint-based approach that controls the error in some output functional. Adaptive results are shown for laminar subsonic flow over a delta wing, laminar subsonic flow over ONERA M6 wing, inviscid supersonic flow over a sonic boom test case, and a turbulent flow over a high lift configuration (JAXA Standard Model). Mesh convergence results are also compared with results from FUN3D-FV (Finite Volume) whenever available. For all test cases considered, FUN3D-SFE gives significantly better accurate results than FUN3D-FV on coarse meshes.

Aravind Balan↗
NASA NTRSDate not supplied

FUN3D Mesh Adaptation Simulations of 4th AIAA High-Lift Prediction Workshop Case 1a

This paper describes in detail the FUN3D Mesh adaptation simulation results for Case 1a of the 4th AIAA High-Lift Prediction Workshop (HLPW-4). The Stabilized Finite Element library with FUN3D is used along with the Negative Spalart-Allmaras One-Equation Model to simulate fully turbulent free-air flow around the High Lift version of the Common Research Model at three flap settings. Meshes are adapted using multi-scale and goal-oriented metrics. The results are presented and the discussion focuses on the predicted differences between the three flap settings. Coefficients of lift, drag, and pitching moment are predicted within 7% of values measured in the QinetiQ 5m Wind Tunnel at each flap setting. Predicted surface pressures and skin friction distributions show inconsistent discrepancies with measurements across the flap settings. Consequently, flap increments for these figures of merit are not well predicted. These predictions are consistent with submissions to the HLPW-4 from other RANS-SA methods. Visualizations of Liutex vortex cores colored by angular velocity are presented as possible new quantitative and qualitative perspective for solution evaluation.

High-Lift Prediction Workshop↗
NASA NTRSDate not supplied

Boundary-Layer Transition Prediction Through Loose Coupling of OVERFLOW and LASTRAC

Transition prediction based on linear stability theory is expected to more accurately reflect the causality of transition onset than phenomenological transition models based on RANS-like transport equations. To help achieve the CFD vision 2030 aim of building a CFD tool chain with automated prediction of boundary layer transition, a technique to loosely tie the NASA OVERFLOW CFD solver with the LASTRAC stability analysis tool is described. The coupled solver is then used to compute transition over selected over a flat plate in a freestream with sufficiently low levels of turbulence, NLF(1)-0416 airfoil, the 6:1 prolate spheroid at an angle of attack, and a NASA juncture flow model with symmetric wing configuration. The findings show that the loosely coupled approach can reliably predict the transition location accurately in scenarios that are dominated by a single transition mechanism involving Tollmien-Schlichting instabilities, crossflow instabilities, or separation bubble-induced transition, or include a mixture of selected mechanisms. The toolset presents here appears to be robust to the prescription of the initial transition location, and it can lead to a converged solution in four or five rounds of the mean flow calculation and stability analysis, with minimal input from the user.

boundary layer transition↗
NASA NTRS2018

Nosetip Bluntness Effects on Transition at Hypersonic Speeds: Experimental and Numerical Analysis Under NATO STO AVT-240

The existing database of transition measurements in hypersonic ground facilities has established that the onset of boundary layer transition over a circular cone at zero angle of attack shifts downstream as the nosetip bluntness is increased with respect to a sharp cone. However, this trend is reversed at sufficiently large values of the nosetip Reynolds number, so that the transition onset location eventually moves upstream with a further increase in nosetip bluntness. This transition reversal phenomenon, which cannot be explained on the basis of linear stability theory, was the focus of a collaborative investigation under the NATO STO group AVT-240 on Hypersonic Boundary-Layer Transition Prediction. The current paper provides an overview of that effort, which included wind tunnel measurements in three different facilities and theoretical analysis related to modal and nonmodal amplification of boundary layer disturbances. Because neither first and second-mode waves nor entropy-layer instabilities are found to be substantially amplified to initiate transition at large bluntness values, transient (i.e., nonmodal) disturbance growth has been investigated as the potential basis for a physics-based model for the transition reversal phenomenon. Results of the transient growth analysis indicate that disturbances that are initiated within the nosetip or in the vicinity of the juncture between the nosetip and the frustum can undergo relatively significant nonmodal amplification and that the maximum energy gain increases nonlinearly with the nose radius of the cone. This finding does not provide a definitive link between transient growth and the onset of transition, but it is qualitatively consistent with the experimental observations that frustum transition during the reversal regime was highly sensitive to wall roughness, and furthermore, was dominated by disturbances that originated near the nosetip.

Numerical analysis↗
NASA NTRS1956

An investigation of the loads on the vertical tail of a jet-bomber airplane resulting from flight through rough air

Vertical-tail loads were measured in turbulent air on a four-engine jet bomber. Results showed large load oscillations which were lightly damped. Comparison of experimental results with discrete-load calculations indicated that discrete-gust calculations underestimated the loads by 30 to 40 percent and gave no indication of the low damping. Power spectral analysis, on the other hand, indicated the general frequency characteristics and gave a somewhat better estimate of the peak-load distributions. The present results strongly suggest that discrete-gust calculation for gust loads on vertical tails may seriously underestimate the gust loads for airplanes having lightly damped lateral oscillations.

GUSTS, FREQUENCY↗
NASA NTRS2000

Annual Research Briefs - 2000: Center for Turbulence Research

This report contains the 2000 annual progress reports of the postdoctoral Fellows and visiting scholars of the Center for Turbulence Research (CTR). It summarizes the research efforts undertaken under the core CTR program. Last year, CTR sponsored sixteen resident Postdoctoral Fellows, nine Research Associates, and two Senior Research Fellows, hosted seven short term visitors, and supported four doctoral students. The Research Associates are supported by the Departments of Defense and Energy. The reports in this volume are divided into five groups. The first group largely consists of the new areas of interest at CTR. It includes efficient algorithms for molecular dynamics, stability in protoplanetary disks, and experimental and numerical applications of evolutionary optimization algorithms for jet flow control. The next group of reports is in experimental, theoretical, and numerical modeling efforts in turbulent combustion. As more challenging computations are attempted, the need for additional theoretical and experimental studies in combustion has emerged. A pacing item for computation of nonpremixed combustion is the prediction of extinction and re-ignition phenomena, which is currently being addressed at CTR. The third group of reports is in the development of accurate and efficient numerical methods, which has always been an important part of CTR's work. This is the tool development part of the program which supports our high fidelity numerical simulations in such areas as turbulence in complex geometries, hypersonics, and acoustics. The final two groups of reports are concerned with LES and RANS prediction methods. There has been significant progress in wall modeling for LES of high Reynolds number turbulence and in validation of the v(exp 2) - f model for industrial applications.

Source record↗
NASA NTRS1984

On the stability of the decelerating laminar boundary layer

The stability of a decelerating boundary-layer flow is investigated experimentally and numerically. Experimentally, a flat plate having a Blasius boundary layer is decelerated in an 18 m towing tank. The boundary layer becomes unstable to two-dimensional waves, which break down into three-dimensional patterns, hairpin vortices, and finally turbulent bursts when the vortices lift off the wall. The unsteady boundary-layer equations are solved numerically to generate instantaneous velocity profiles for a range of boundary and initial conditions. A quasi-steady approximation is invoked and the stability of local velocity profiles is determined by solving the Orr-Sommerfeld equation using Chebyshev matrix methods. Comparisons are made between the numerical predictions and the experimentally observed instabilities.

Gad-El-hak, M.↗
NASA NTRS1991

Simulation evaluation of a speed-guidance law for Harrier approach transitions

An exponential-deceleration speed guidance law is formulated which mimics the technique currently used by Harrier pilots to perform decelerating approaches to a hover. This guidance law was tested along with an existing two-step constant deceleration speed guidance law, using a fixed-base piloted simulator programmed to represent a YAV-8B Harrier. Decelerating approaches to a hover at a predetermined station-keeping point were performed along a straight (-3 deg glideslope) path in headwinds up to 40 knots and turbulence up to 6 ft./sec. Visibility was fixed at one-quarter nautical mile and 100 ft. cloud ceiling. Three Harrier pilots participated in the experiment. Handling qualities with the aircraft equipped with the standard YAV-8B rate damped attitude stability augmentation system were adequate (level 2) using either speed guidance law. However, the exponential deceleration speed guidance law was rated superior to the constant-deceleration speed guidance law by a Cooper-Harper handling qualities rating of about one unit independent of the level of wind and turbulence. Replacing the attitude control system of the YAV-8B with a high fidelity model following attitude flight controller increased the approach accuracy and reduced the pilot workload. With one minor exception, the handling qualities for the approach were rated satisfactory (level 1). It is concluded that the exponential deceleration speed guidance law is the most cost effective.

Merrick, Vernon K.↗
NASA NTRS1972

Effect of configuration modifications on the low-subsonic aerodynamic characteristics of a space shuttle orbiter concept with a blended delta wing-body

An investigation of several configuration modifications to improve the subsonic stability and performance of a blended delta wing-body space shuttle-orbiter concept has been conducted in the Langley low-turbulence pressure tunnel. These modifications included variations in vertical-tail location and orientation, wing planform shape, and afterbody shape. The model was tested at a Reynolds number, based on body length, of 17 x one million, at a Mack number of 0.25, and at angles of attack from about -4 deg to 22 deg.

Freeman, D. C., Jr.↗
NASA NTRS1979

An experimental study of the flow field and pollutant formation in a two dimensional premixed, turbulent flame

Spark shadowgraphs, high-speed schlieren movies, and the tracing of individual eddies were used to study a turbulent reacting shear layer in a premixed propane/air flow. The flow took place in a two-dimensional combustor, and the flame was stabilized behind a rearward facing streamlined step. The data show that in the velocity range 7.5 to 22.5 m/sec the mixing layer is dominated by Brown-Roshko type large coherent structures in both reacting and nonreacting flows. Information on the eddies, the flame, and the distribution of gas concentrations is presented.

Ganji, A. R.↗
NASA NTRS1979

Aircraft identification experience

Important aspects of estimating the unknown coefficients of the aircraft equations of motion from dynamic flight data are presented. The primary topic is the application of the maximum likelihood estimation technique. Basic considerations that must be addressed in the estimation of stability and control derivatives from conventional flight maneuvers are discussed. Some complex areas of estimation (such as estimation in the presence of atmospheric turbulence, estimation of acceleration derivatives, and analysis of maneuvers where both kinematic and aerodynamic coupling are present) are also discussed.

Iliff, K. W.↗
NASA NTRS1993

The three-dimensional evolution of a plane wake

In the past three decades, linear stability analysis has led to a comprehensive understanding of the linear stages of transition in plane wakes. Our understanding of the nonlinear and turbulent stages is less developed. Nonlinear theory developed by Papageorgiou and Smith was used to study the long-wavelength regime in wakes. The nonlinear and turbulent stages were investigated experimentally, and few numerical studies examined the early nonlinear stages of forced wakes. The evolution of three dimensional disturbances in an incompressible wake is investigated using direct numerical simulations. The instantaneous three-dimaensional structures and corresponding statistics are presented.

Maekawa, H.↗
NASA NTRS1997

Evaluation of a Neural Adaptive Flight Controller

The objective of this paper is to present results from the evaluation of a direct adaptive tracking controller. The control architecture employs both pre-trained and an on-line neural networks to represent the non-linear aircraft dynamics in the model inversion portion of the controller. The aircraft model used for this evaluation is representative of the F-15 Advanced Control Technology for Integrated Vehicles (ACTIVE) aircraft. The controller was evaluated for three cases: (1) nominal conditions; (2) loss of control power; and (3) loss of control power in the presence of atmospheric turbulence. The results were compared with the existing F-15 ACTIVE conventional mode controller in all cases. The results indicate extremely desirable airframe stabilization characteristics for case (1) that do not degrade significantly for case (2) or (3) as does the conventional mode controller. It was concluded that this controller exhibits both stable and robust adaptive characteristics when subjected to mild and extreme loss of control power conditions. Integration of this neural adaptive flight controller into the full non-linear six degree-of-freedom F-15 ACTIVE simulation is recommended for evaluation in a real-time high fidelity piloted simulation environment.

Totah, Joseph J.↗
NASA NTRS2003

Extension of Liouville Formalism to Postinstability Dynamics

A mathematical formalism has been developed for predicting the postinstability motions of a dynamic system governed by a system of nonlinear equations and subject to initial conditions. Previously, there was no general method for prediction and mathematical modeling of postinstability behaviors (e.g., chaos and turbulence) in such a system. The formalism of nonlinear dynamics does not afford means to discriminate between stable and unstable motions: an additional stability analysis is necessary for such discrimination. However, an additional stability analysis does not suggest any modifications of a mathematical model that would enable the model to describe postinstability motions efficiently. The most important type of instability that necessitates a postinstability description is associated with positive Lyapunov exponents. Such an instability leads to exponential growth of small errors in initial conditions or, equivalently, exponential divergence of neighboring trajectories. The development of the present formalism was undertaken in an effort to remove positive Lyapunov exponents. The means chosen to accomplish this is coupling of the governing dynamical equations with the corresponding Liouville equation that describes the evolution of the flow of error probability. The underlying idea is to suppress the divergences of different trajectories that correspond to different initial conditions, without affecting a target trajectory, which is one that starts with prescribed initial conditions.

Zak, Michail↗