Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Thin Section”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

Bending-torsion flutter of a highly swept advanced turboprop

Experimental and analytical results are presented for a bending-torsion flutter phenomena encountered during wind-tunnel testing of a ten-bladed, advanced, high-speed propeller (turboprop) model with thin airfoil sections, high blade sweep, low aspect ratio, high solidity and transonic tip speeds. Flutter occurred at free-stream Mach numbers of 0.6 and greater and when the relative tip Mach number (based on vector sum of axial and tangential velocities) reached a value of about one. The experiment also included two- and five-blade configurations. The data indicate that aerodynamic cascade effects have a strong destabilizing influence on the flutter boundary. The data was correlated with analytical results which include aerodynamic cascade effects and good agreement was found.

Mehmed, O.↗

The Alternating Surface Segmented Lap Joint: a Design for Thin Highly Loaded Joints

The combination of thin airfoil sections and high aerodynamic loads on many wind tunnel models presents a major problem for attachment of flap elements. Conventional methods of attaching fixed control elements such as lap and tongue-in-groove joints are not rigid enough to provide surface continuity required in high Reynolds number research. For the extreme cases, the solution has been to fabricate separate wings for each flap setting with the flap element being and integral part of the wing. Here an attractive solution to this problem, the alternating surface segmented lap joint, is discussed. This joint provides increased rigidity and lower stress levels than conventional joints. Additionally, attachment fastener loading is low and the joint can be designed to accommodate high shear levels due to bending without the use of dowel pins.

Watkins, V. E., Jr.↗

Four Antarctic ureilites - Petrology and observations on ureilite petrogenisis

New data are presented on the petrography and mineral compositions of four recently recovered Antarctic ureilites: Yamato-790981, RKPA80239, ALHA81101, and PCA82506. Thin polished sections of the ureilites were analyzed by polarized and reflected light microscopy, and by electron microprobe. The low shock characteristics of most (with the exception of the ALHA81101) Antarctic ureilites have afforded excellent opportunities for understanding the petrographic relationships between graphite and silicate minerals in ureilites. New speculations concerning the petrogenesis of ureilites are offered.

Berkley, J. L.↗

The Jamestown Ophiolite Complex, Barberton mountain belt - A section through 3.5 Ga oceanic crust

The Jamestown Ophiolite Complex of the Barberton greenstone belt, South Africa, is investigated, and the intrusive nature of mafic-ultramafic units from the Komati and Kromberg formations into overlying pillow lavas and sediments is documented. Evidence is presented for multiple intrusive events within the igneous sections, including crosscutting intrusives, multiple injection of magma in the Komati section, and sheeted intrusions in the Kromberg section. The thinness of the Jamestown complex suggests that, locally at least, the ca 3.5 Ga oceanic crust was also thin, consistent with the regionally extensive metasomatic alteration.

De Wit, Maarten J.↗

Application of the CAP-TSD unsteady transonic small disturbance program to wing flutter

The application and assessment of a computer program called CAP-TSD (Computational Aeroelasticity Program - Transonic Small Disturbance) for flutter predictions are described. Flutter calculations are presented for two thin swept-and-tapered wing planforms with well-defined modal properties. One planform is a series of 45-degree swept wings and the other planform is a clipped delta wing. Comparisons are made between the results of CAP-TSD using the linear equation and no airfoil thickness and the results obtained from a subsonic kernel function analysis. The calculations cover a Mach number range from low subsonic to low supersonic values, including the transonic range, and are compared with subsonic linear theory and experimental data. It is noted that since both wings have very thin airfoil sections, the effects of thickness are minimal.

Bennett, Robert M.↗

LEWICE/E: An Euler based ice accretion code

A new version of the LEWICE ice accretion computer code was developed which calculates the ice growth on two dimensional surfaces, incorporating the effects of compressibility through the solution of the Euler equations. The code is modular and contains separate stand-alone program elements that create a grid, calculate the flow field parameters, calculate the droplet trajectory paths, determine the amount of ice growth, and plot results. This code increases the applicability of ice accretion predictions by allowing calculations at higher Mach numbers. The new elements of the code are described. Calculated results are compared to experiment for several cases, including a LEWICE example case and a thin airfoil section at a Mach number of 0.58.

Potapczuk, Mark G.↗

LEWICE/E - An Euler based ice accretion code

A new version of the LEWICE ice accretion computer code was developed which calculates the ice growth on two dimensional surfaces, incorporating the effects of compressibility through the solution of the Euler equations. The code is modular and contains separate stand-alone program elements that create a grid, calculate the flow field parameters, calculate the droplet trajectory paths, determine the amount of ice growth, and plot results. This code increases the applicability of ice accretion predictions by allowing calculations at higher Mach numbers. The new elements of the code are described. Calculated results are compared to experiment for several cases, including a LEWICE example case and a thin airfoil section at a Mach number of 0.58.

Potapczuk, Mark G.↗

In-phase and out-of-phase axial-torsional fatigue behavior of Haynes 188 at 760 C

Isothermal, in-phase and out-of-phase axial-torsional fatigue experiments have been conducted at 760 C on uniform gage section, thin-walled tubular specimens of a wrought cobalt-base superalloy, Haynes 188. Test-control and data acquisition were accomplished with a minicomputer. Fatigue lives of the in- and out-of-phase axial-torsional fatigue tests have been estimated with four different multiaxial fatigue life prediction models that were developed primarly for predicting axial-torsional fatigue lives at room temperature. The models investigated were: (1) the von Mises equivalent strain range; (2) the Modified Multiaxiality Factor Approach; (3) the Modified Smith-Watson-Topper Parameter; and (4) the critical shear plane method of Fatemi, Socie, and Kurath. In general, life predictions by the von Mises equivalent strain range model were within a factor of 2 for a majority of the tests and the predictions by the Modified Multiaxiality Factor Approach were within a factor of 2, while predictions of the Modified Smith-Watson-Topper Parameter and of the critical shear plane method of Fatemi, Socie, and Kurath were unconservative and conservative, respectively, by up to factors of 4. In some of the specimens tested under combined axial-torsional loading conditions, fatigue cracks initiated near extensometer indentations. Two design modifications have been proposed to the thin-walled tubular specimen to overcome this problem.

Kalluri, Sreeramesh↗

Experimental Performance of a Micromachined Heat Flux Sensor

Steady-state and frequency response calibration of a microfabricated heat-flux sensor have been completed. This sensor is batch fabricated using standard, micromachining techniques, allowing both miniaturization and the ability to create arrays of sensors and their corresponding interconnects. Both high-frequency and spatial response is desired, so the sensors are both thin and of small cross-sectional area. Thin-film, temperature-sensitive resistors are used as the active gauge elements. Two sensor configurations are investigated: (1) a Wheatstone-bridge using four resistors; and (2) a simple, two-resistor design. In each design, one resistor (or pair) is covered by a thin layer (5000 A) thermal barrier; the other resistor (or pair) is covered by a thick (5 microns) thermal barrier. The active area of a single resistor is 360 microns by 360 microns; the total gauge area is 1.5 mm square. The resistors are made of 2000 A-thick metal; and the entire gauge is fabricated on a 25 microns-thick flexible, polyimide substrate. Heat flux through the surface changes the temperature of the resistors and produces a corresponding change in resistance. Sensors were calibrated using two radiation heat sources: (1) a furnace for steady-state, and (2) a light and chopper for frequency response.

TEMPERATURE SENSITIVE ELEMENTS↗

Nonstationary Gas Flow in Thin Pipes of Variable Cross Section

Characteristic methods for nonstationary flows have been published only for the special case of the isentropic flow up until the present, althought they are applicable in various places to more difficult questions too. This report derives the characteristic method for the flows which depend only on the position coordinates and time. At the same time the treatment of compression shocks is shown.

Guderley, G.↗

Influence of Shock Wave on the Flutter Behavior of Fan Blades Investigated

Modern fan designs have blades with forward sweep; a lean, thin cross section; and a wide chord to improve performance and reduce noise. These geometric features coupled with the presence of a shock wave can lead to flutter instability. Flutter is a self-excited dynamic instability arising because of fluid-structure interaction, which causes the energy from the surrounding fluid to be extracted by the vibrating structure. An in-flight occurrence of flutter could be catastrophic and is a significant design issue for rotor blades in gas turbines. Understanding the flutter behavior and the influence of flow features on flutter will lead to a better and safer design. An aeroelastic analysis code, TURBO, has been developed and validated for flutter calculations at the NASA Glenn Research Center. The code has been used to understand the occurrence of flutter in a forward-swept fan design. The forward-swept fan, which consists of 22 inserted blades, encountered flutter during wind tunnel tests at part speed conditions.

Srivastava, Rakesh↗

A Multispectral Micro-Imager for Lunar Field Geology

Field geologists routinely assign rocks to one of three basic petrogenetic categories (igneous, sedimentary or metamorphic) based on microtextural and mineralogical information acquired with a simple magnifying lens. Indeed, such observations often comprise the core of interpretations of geological processes and history. The Multispectral Microscopic Imager (MMI) uses multi-wavelength, light-emitting diodes (LEDs) and a substrate-removed InGaAs focal-plane array to create multispectral, microscale reflectance images of geological samples (FOV 32 X 40 mm). Each pixel (62.5 microns) of an image is comprised of 21 spectral bands that extend from 470 to 1750 nm, enabling the discrimination of a wide variety of rock-forming minerals, especially Fe-bearing phases. MMI images provide crucial context information for in situ robotic analyses using other onboard analytical instruments (e.g. XRD), or for the selection of return samples for analysis in terrestrial labs. To further assess the value of the MMI as a tool for lunar exploration, we used a field-portable, tripod-mounted version of the MMI to image a variety of Apollo samples housed at the Lunar Experiment Laboratory, NASA s Johnson Space Center. MMI images faithfully resolved the microtextural features of samples, while the application of ENVI-based spectral end member mapping methods revealed the distribution of Fe-bearing mineral phases (olivine, pyroxene and magnetite), along with plagioclase feldspars within samples. Samples included a broad range of lithologies and grain sizes. Our MMI-based petrogenetic interpretations compared favorably with thin section-based descriptions published in the Lunar Sample Compendium, revealing the value of MMI images for astronaut and rover-mediated lunar exploration.

Nunez, Jorge↗

Quantitative Examination of a Large Sample of Supra-Arcade Downflows in Eruptive Solar Flares

Sunward-flowing voids above post-coronal mass ejection flare arcades were first discovered using the soft X-ray telescope aboard Yohkoh and have since been observed with TRACE (extreme ultraviolet (EUV)), SOHO/LASCO (white light), SOHO/SUMER (EUV spectra), and Hinode/XRT (soft X-rays). Supra-arcade downflow (SAD) observations suggest that they are the cross-sections of thin flux tubes retracting from a reconnection site high in the corona. Supra-arcade downflowing loops (SADLs) have also been observed under similar circumstances and are theorized to be SADs viewed from a perpendicular angle. Although previous studies have focused on dark flows because they are easier to detect and complementary spectral data analysis reveals their magnetic nature, the signal intensity of the flows actually ranges from dark to bright. This implies that newly reconnected coronal loops can contain a range of hot plasma density. Previous studies have presented detailed SAD observations for a small number of flares. In this paper, we present a substantial SADs and SADLs flare catalog. We have applied semiautomatic detection software to several of these events to detect and track individual downflows thereby providing statistically significant samples of parameters such as velocity, acceleration, area, magnetic flux, shrinkage energy, and reconnection rate. We discuss these measurements (particularly the unexpected result of the speeds being an order of magnitude slower than the assumed Alfven speed), how they were obtained, and potential impact on reconnection models.

Savage, Sabrina L.↗

Sandwich Core Heat-Pipe Radiator for Power and Propulsion Systems

Next-generation heat-pipe radiator technologies are being developed at the NASA Glenn Research Center to provide advancements in heat-rejection systems for space power and propulsion systems. All spacecraft power and propulsion systems require their waste heat to be rejected to space in order to function at their desired design conditions. The thermal efficiency of these heat-rejection systems, balanced with structural requirements, directly affect the total mass of the system. Terrestrially, this technology could be used for thermal control of structural systems. One potential use is radiant heating systems for residential and commercial applications. The thin cross section and efficient heat transportability could easily be applied to flooring and wall structures that could evenly heat large surface areas. Using this heat-pipe technology, the evaporator of the radiators could be heated using any household heat source (electric, gas, etc.), which would vaporize the internal working fluid and carry the heat to the condenser sections (walls and/or floors). The temperature could be easily controlled, providing a comfortable and affordable living environment. Investigating the appropriate materials and working fluids is needed to determine this application's potential success and usage.

Gibson, Marc↗

Precision Measurement of the Nickel Spectrum in Cosmic Rays from 8.8 GeV/n to 240 GeV/n with CALET on the International Space Station

The relative abundance of nickel with respect to iron is by far larger than all other trans-iron elements, therefore it provides a favourable opportunity for a low background measurement of its spectrum. Since nickel, as well as iron, is one of the most stable nuclei, the nickel energy spectrum and its relative abundance with respect to iron provide important information to estimate the abundances at the source and to model the propagation of heavy nuclei. However, only a few direct measurements of cosmic-ray nickel at energy larger than∼3 GeV/n are available at present in the literature and they are affected by strong limitations in both energy reach and statistics. In this paper we present a measurement of the differential energy spectrum of nickel from 8.8 GeV/nto 240 GeV/n, carried out with unprecedented precision by the Calorimetric Electron1 Telescope(CALET) in operation on the International Space Station since 2015. The CALET instrument can identify individual nuclear species via a measurement of their electric charge with a dynamic range extending far beyond iron (up to atomic number Z = 40). The particle’s energy is measured by a homogeneous calorimeter (1.2 proton interaction lengths, 27 radiation lengths) preceded by a thin imaging section (3 radiation lengths) providing tracking and energy sampling. This paper follows our previous measurement of the iron spectrum [1] and it extends our investigation on the energy dependence of the spectral index of heavy elements. It reports the analysis of nickel data collected from November 2015 to May 2021 and a detailed assessment of the systematic uncertainties. In the region from 20 GeV/nto 240 GeV/n our present data are compatible within the errors with a single power law with spectral index−2.51±0.07.

O Adriani↗

Heterogeneity of Bulk Oxygen Isotopic Compositions in Anhydrous Interplanetary Dust Particles

Introduction: Anhydrous interplanetary dust particles are one of the least altered ancient solar systemmaterials. Their bulk chemical compositions match those of CI chondrites within a factor of 2-3, except for carbonwhich is enriched in both anhydrous and hydrated IDPs by ~4x CI [1]. Hydrous IDPs often show 16O-poor isotopiccompositions, likely due to the interaction with isotopically heavy H2O [2]. Anhydrous IDPs are interpreted tooriginate from comets from the outer solar system [3]. Oxygen isotopic data for these materials is scarce, but resultspoint to a wider range of compositions [4]. This heterogeneity might be a result of mixing between a 16O-rich and a16O-poor reservoir formed via self-shielding and photodissociation of CO [5]. Here, we report bulk oxygen isotopiccompositions of three anhydrous IDPs in context of their mineralogical composition and discuss possible origins ofisotopic heterogeneity. Experimental: Bulk chemical composition and mineralogy of 70 nm thin ultramicrotomed sections of threeanhydrous IDPs (L2099A7, L2099A8, and L2071AB1) were analyzed using a Thermo Scientific Titan Themis G360-300 TEM equipped with a four-quadrant energy-dispersive X-ray detector (Super-X G2) at University ofMünster. Bulk oxygen isotopic compositions were measured using a NanoSIMS 50 at the Max-Planck-Institut fürChemie in Mainz. A focused Cs+ ion beam (~1 pA, ~100 nm) was rastered over a field of view varying from 5 x 5 to6 x 6 μm2, depending on particle size for 15 layers. Negative secondary ions of 16O, 17O, 18O, 12C14N, and 28Si werecollected on electron multipliers. The 16OH contribution to the 17O peak was 1-2 ‰. As a standard, a matrix regionof meteorite CR2 Queen Alexandra Range (QUE) 99177 was used, whose oxygen isotopic composition wasmeasured by [6]. Results and Discussion: Particles A7 and A8 are both fine-grained, consisting mostly of small, 100 nm-sizedequilibrated aggregates (EA). Both particles exhibit discontinuous magnetite rims with thicknesses up to 50 nm inA7 and 100 nm in A8 on the outsides. In Particle AB1, the upper part of the particle consists of a few EAs, while thelower part contains lots of small GEMS grains with 100-200 nm diameter clustered together. Magnetite rims arenearly absent, the rare rims reaching maximum 20 nm thickness, indicating that AB1 is of more primitive naturethan the other two IDPs [1]. Furthermore, it contains several diffuse GEMS-like areas, identified by an amorphoussilicate groundmass with small nano-inclusions of Fe,Ni-metal and Fe-sulfides. All three particles are subsolar forall major element/Si ratios. Mean S/Si of particles A7 and A8 is 0.046 and 0.048, respectively, while it is an order ofmagnitude higher in AB1 (0.184). This reflects the higher degree of thermal alteration in A7 and A8, resulting in theloss of volatile S and oxidation of Fe-sulfides and FeNi-metal to magnetite as present in particle rims. A8 is rather16O-poor with δ17OSMOW = 7.8 ± 3.4 ‰ and δ18OSMOW = 9.5 ± 3.1 ‰ (1σ), followed by A7 with δ17OSMOW = − 0.8 ±4.6 ‰ and δ18OSMOW = −2.2 ± 3.4 ‰. In contrast to that, AB1 has the most 16O-rich bulk composition with δ17OSMOW= −24.2 ± 5.4 ‰ and δ18OSMOW = −25.3 ± 3.6 ‰. All investigated IDPs plot slightly above the CCAM line aspreviously reported for other anhydrous IDPs [4], maybe due to a contribution from circumstellar dust from AGBstars enriched in 17O [7]. The 16O-rich composition of AB1 is similar to the most 16O-rich anhydrous IDP U2015D21measured by [8] which is dominated by GEMS [9] and the GEMS-rich IDP GM4-2 reported by [10]. Nevertheless,it is unlikely that GEMS are the carrier for the 16O-rich composition of AB1 because most GEMS have O isotopiccompositions indistinguishable from terrestrial values, although errors on these analyses are large [11]. The isotopicheterogeneity is best explained by contribution of grains from different regions in the protoplanetary disk, samplingdifferent O isotope reservoirs, created by self-shielding and photodissociation of CO. This process resulted in 16O-rich CO gas and 16O-poor H2O that froze as ice-mantles onto dust grains [12]. Alternatively, the higher degree ofheating in A7 and A8 could have influenced isotopic fractionation, because higher δ17,18O values are reported fromthe regions of the atmosphere where small particles are heated and oxidized, as observed for the thermal alteration ofcosmic spherules [13]. Acknowledgements: We would like to thank NASA Astromaterials Acquisition & Curation Office for providing IDPsamples and DFG for funding this project (VO1816/5-1)

B Schulz↗

Towards Integrated Computational Materials Engineering for Quantifying Performance Impacts of Microstructure and Defect Interactions in Powder Bed Fusion Parts

Powder bed fusion (PBF) additive manufacturing (AM) enables the creation of parts with complexity and functionality levels that were previously impossible with traditional manufacturing methods. By modifying the laser power, hatch spacing, or the numerous other processing parameters, the PBF process supports the production of a wide set of materials and geometries. However, that same process parameter design flexibility causes the process-design space of PBF to be massive and expensive to explore experimentally. Another challenge is quality variation across a build. As a part is being built, geometric variance between locations, such as at a thin-wall section vs. the bulk material, may cause the specified processing parameters to no longer be acceptable for producing defect-free printing. Furthermore, if the processing parameters deviate during the print process, it is difficult to assess if the part will still perform satisfactorily. Integrated Computational Materials Engineering (ICME) provides a way to understand and address these various challenges. This talk will present advancements in process-structure simulations of PBF at NASA Langley Research Center. The ability to simulate grain-scale PBF microstructures using the Physically Based Monte Carlo method will be demonstrated and compared to experimental measurements. Techniques for simulating three-dimensional lack-of-fusion and keyhole porosity defects based on the specific processing conditions and approaches for integrating the two porosity prediction techniques alongside the computational microstructure evolution models will be shown. Finally, the integration of simulated PBF microstructures, embedded process defects, and crystal plasticity finite element models to elucidate the interaction of porosity and microstructure on micromechanical fields will be demonstrated. These integrated techniques demonstrate an example of using ICME to relate processing to performance for PBF AM materials. With continued maturity, it is hoped that such ICME approaches will lead to next-generation computational-materials supported qualification and certification of AM parts.

Additive manufacturing↗