Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “THIN FILMS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Beryllium thin films for resistor applications

Beryllium thin films have a protective oxidation resistant property at high temperature and high recrystallization temperature. However, the experimental film has very low temperature coefficient of resistance.

Fiet, O.↗
NASA NTRS1986

Measurement of heat-transfer coefficients in shock wave-turbulent boundary layer interaction regions with a multi-layered thin film heat transfer gauge

A thin film heat transfer gauge is applied to the measurement of heat transfer coefficients in the interaction regions of incident shock waves and fully developed turbulent boundary layers. It was developed to measure heat flux with high spatial resolution and fast response for wind tunnels with long flow duration. To measure the heat transfer coefficients in the interaction region in detail, experiments were performed under the conditions of Mach number = 4, total pressure = 1.2 MPa, 0.59 to approximately 0.65. Reynolds number = 1.3 to approximately 1.5 x 10 to the 7th power and incident shock angles from 17.8 to 22.8 degrees. The results show that the heat transfer coefficient changes complicatedly in the interaction region. At the beginning the interaction region, the heat transfer coefficient decreases at first, reaches its minimum value at the point where the pressure begins to increase, and then increases sharply. When the boundary layer begins to separate, even a small separation bubble causes significant changes in the heat transfer coefficient, while the pressure does not show any changes which suggests that the boundary layer begins to separate.

Hayashi, M.↗
NASA NTRS1991

The effect of temperature cycling typical of low earth orbit satellites on thin films of YBa2Cu3O(7-x)

Thin films of YBa2Cu3O(7-x) (YBCO) were temperature cycled to simulate conditions of a low earth orbit satellite. In one series of tests, epitaxial and polycrystalline YBCO films were cycled between temperatures of +/- 80 C in vacuum and in nitrogen for hundreds of cycles. The room temperature resistance of an epitaxial YBCO film increased by about 10 percent, but the superconducting transition temperature was unchanged. The largest changes were for a polycrystalline YBCO film on oxidized silicon with a zirconia buffer layer, for which the transition temperature decreased by 3 K. An extended test was carried out for epitaxial films. After 3200 cycles (corresponding to about 230 days in space), transition temperatures and critical current densities remained unchanged.

Mogro-Campero, A.↗
NASA NTRS1991

Fabrication of thin film heat flux sensors

Thin-film heat-flux sensors have been constructed in the form of arrays of thermocouples on upper and lower surfaces of an insulating layer, so that flux values are proportional to the temperature difference across the upper and lower surface of the insulation material. The sensor thermocouples are connected in thermopile arrangement, and the structure is patterned with photolithographic techniques. Both chromel-alumel and Pt-Pt/Rh thermocouples have been devised; the later produced 28 microvolts when exposed to the radiation of a 1000 C furnace.

Will, Herbert↗
DOE OSTI2024

Atomic layer molecular beam epitaxy of kagome magnet RMn6Sn6 (R = Er, Tb) thin films

Kagome lattices have garnered substantial interest because their band structure consists of topological flat bands and Dirac cones. The RMn6Sn6 (R = rare earth) compounds are particularly interesting because of the existence of the large intrinsic anomalous Hall effect (AHE), which originates from the gapped Dirac cones near the Fermi level. This makes RMn6Sn6 an outstanding candidate for realizing the high-temperature quantum AHE. The growth of RMn6Sn6 thin films is beneficial for both fundamental research and potential applications. However, most of the studies on RMn6Sn6 have focused on bulk crystals, and the synthesis of RMn6Sn6 thin films has not been reported so far. Here, we report the atomic layer molecular beam epitaxy growth, structural and magnetic characterizations, and transport properties of ErMn6Sn6 and TbMn6Sn6 thin films. It is especially noteworthy that TbMn6Sn6 thin films have out-of-plane magnetic anisotropy, which is important for realizing the quantum AHE. Our work paves the avenue toward the control of the AHE using devices patterned from RMn6Sn6 thin films.

Materials Science↗
NASA NTRS1991

Microwave response of high transition temperature superconducting thin films

We have studied the microwave response of YBa2Cu3O(7 - delta), Bi-Sr-Ca-Cu-O, and Tl-Ba-Ca-Cu-O high transition temperature superconducting (HTS) thin films by performing power transmission measurements. These measurements were carried out in the temperature range of 300 K to 20 K and at frequencies within the range of 30 to 40 GHz. Through these measurements we have determined the magnetic penetration depth (lambda), the complex conductivity (sigma(sup *) = sigma(sub 1) - j sigma(sub 2)) and the surface resistance (R(sub s)). An estimate of the intrinsic penetration depth (lambda approx. 121 nm) for the YBa2Cu3O(7 - delta) HTS has been obtained from the film thickness dependence of lambda. This value compares favorably with the best values reported so far (approx. 140 nm) in single crystals and high quality c-axis oriented thin films. Furthermore, it was observed that our technique is sensitive to the intrinsic anisotropy of lambda in this superconductor. Values of lambda are also reported for Bi-based and Tl-based thin films. We observed that for the three types of superconductors, both sigma(sub 1) and sigma(sub 2) increased when cooling the films below their transition temperature. The measured R(sub s) are in good agreement with other R(sub S) values obtained using resonant activity techniques if we assume a quadratic frequency dependence. Our analysis shows that, of the three types of HTS films studied, the YBa2Cu3O(7 - delta) thin film, deposited by laser ablation and off-axis magnetron sputtering are the most promising for microwave applications.

Miranda, Felix Antonio↗
DOE OSTI2024

Magneto-transport study on Sn-rich Sn 1–x Ge x thin films enabled by CdTe buffer layer

α-Sn, generally known as gray tin, has attracted significant scientific interest due to its potential to host novel topological phases. Studying the transport properties of α-Sn thin films grown on the InSb substrate has been challenging, as the InSb substrate also significantly contributes to the transport properties. In this article, we report a novel approach to epitaxially grow α-Sn thin films on an InSb substrate with a resistive buffer layer of CdTe. Thin films of α–Sn 1–x Ge x (x = 0, 0.025) alloy of 15 nm thickness have been grown using molecular beam epitaxy. The high quality of the samples has been determined through high-resolution x-ray diffraction. The CdTe buffer layer has high resistance and acts as an insulating virtual substrate, which significantly suppresses contribution from InSb. Magnetotransport measurements show clear Shubnikov–de Hass oscillations in α–Sn 1–x Ge x (x = 0, 0.025) thin films. A change in oscillation frequency is observed upon alloying with Ge, implying a modification in the electronic structure and demonstrating the effectiveness of the CdTe buffer layer approach. Furthermore, this work provides a new approach that enables the electronic transport characterization of the α–Sn 1–x Ge x alloy system, which enables the study of the topological quantum states using electronic transport and their device applications.

36 MATERIALS SCIENCE↗
NASA NTRS1996

Characterization of Hybrid Ferroelectric/HTS Thin Films for Tunable Microwave Components

Since the discovery of High-Temperature-Superconductors (HTS) in 1986, a diversity of HTS-based microwave components has been demonstrated. Because of their low conductor losses, HTS-based components are very attractive for integration into microwave circuits for space communication systems. Recent advancements have made deposition of ferroelectric thin films onto HTS thin films possible. Due to the sensitivity of the ferroelectric's dielectric constant (epsilon(sub r)) to an externally applied electric field (E), ferroelectric/superconducting structures could be used in the fabrication of low loss, tunable microwave components. In this paper, we report on our study of Ba(0.5)Sr(0.5)TiO3/YBa2Cu3O(7-delta) and Ba(0.08)Sr(0.92)TiO3/YBa2Cu3O(7-delta) ferroelectric/superconducting thin films on lanthanum aluminate (LaAlO3) substrates. For the (Ba:Sr, 0.50:0.50) epitaxial sample, a epsilon(sub r) of 425 and a loss tangent (tan delta) of 0.040 were measured at 298 K, 1.0 MHz, and zero applied E. For the same sample, a epsilon(sub r) of 360 and tan delta of 0.036 were obtained at 77 K, 1.0 MHz, and zero applied E. Variations in epsilon(sub r) from 180 to 360 were observed over an applied E range of 0V/cm less than or equal to E less than or equal to 5.62 x 10(exp 4) V/cm with little change in tan delta. However, the range of epsilon(sub r) variation for the polycrystalline (Ba:Sr, 0.08:0.92) sample over 0V/cm less than or equal to E less than or equal to 4.00 x 10(exp 4) V/cm was only 3.6 percent while tan delta increased markedly. These results indicate that a lack of epitaxy between the ferroelectric and superconducting layers decreases tuning and increases microwave losses.

Winters, M. D.↗
NASA NTRS2004

Development of Thin Film Ceramic Thermocouples for High Temperature Environments

The maximum use temperature of noble metal thin film thermocouples of 1100 C (2000 F) may not be adequate for use on components in the increasingly harsh conditions of advanced aircraft and next generation launch technology. Ceramic-based thermocouples are known for their high stability and robustness at temperatures exceeding 1500 C, but are typically found in the form of rods or probes. NASA Glenn Research Center is investigating the feasibility of ceramics as thin film thermocouples for extremely high temperature applications to take advantage of the stability and robustness of ceramics and the non-intrusiveness of thin films. This paper will discuss the current state of development in this effort.

Wrbanek, John D.↗
DOE OSTI2020

Crystallization of TiO 2 polymorphs from RF-sputtered, amorphous thin-film precursors

Crystalline TiO 2 films of anatase, brookite, and rutile are reproducibly made from amorphous precursors deposited by RF magnetron sputtering, producing large-area, single phase films of uniform thickness. Sputtered amorphous TiO 2 precursor thin films follow the general behavior observed for amorphous precursor thin films generated by pulsed laser deposition, namely, that oxygen deficiency is necessary for the formation of brookite and rutile. We quantify the oxygen deficiency and correlate it with the long wavelength optical absorption. We find that the precursor deposition rate is also a contributing factor to phase selection and that brookite and rutile form from films deposited more rapidly and anatase from films deposited more slowly. Sputtered and pulsed laser deposited amorphous precursor films prepared with similar oxygen deficiency and similar thickness result in the same final state after annealing, but the rate for sputtered precursors is slower.

14 SOLAR ENERGY↗
DOE OSTI2023

Role of kinetic energy on Nb 3 Sn thin films by low-temperature co-sputtering

Nb 3 Sn is a promising thin film material for superconducting radio frequency (SRF) applications. Although surface resistivity, critical temperature, and critical field are advantageous in comparison to pure Nb, currently the performance of Nb 3 Sn is lacking behind due to its complex defect structure and phase inhomogeneities. In this work, the influence of the kinetic energy of the deposited particles on the defect structure in Nb 3 Sn thin films synthesized at low temperatures is investigated. A combination of extended x-ray absorption fine structure analysis, x-ray absorption spectroscopy mapping, and transmission electron microscopy reveals an improved local order and elemental homogeneity of the Nb 3 Sn films induced by higher kinetic energies of the elemental species during deposition. Even more, these process conditions lead to suppressed local inhomogeneities at grain boundaries, which can be one of the causes of critically reduced superconducting properties of low temperature sputter-coated Nb 3 Sn thin films. Finally, we show that the magnetic field-induced reduction of critical currents across weak-links formed at grain boundaries can be eliminated by the suggested materials’ synthesis.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗