Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STALLING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

Experimental studies of flow separation and stalling on a two-dimensional airfoil at low speeds

Detailed measurements of flow fields associated with low-speed turbulent boundary layers were made for the 17% thick GA(W)-1 airfoil section at nominal angles of attack of 10 deg, 14 deg, and 18 deg, Reynolds number 2.2 x 10, and Mach number 0.13. The data include pressure and velocity surveys of the pre- and post-separated regions on the airfoil and the associated wake. The boundary layer characteristics including regions of separation on the airfoil are also presented.

Seetharam, H. C.↗

Experimental determination of post-stall rotary derivatives for airplane-like configurations at several Reynolds numbers

Military and civilian airplane losses due to out-of-control spin motions are significant. Knowledge of rotary coefficients is necessary to understand the cause of spin entry and to devise proper recovery techniques. An exploratory wind-tunnel investigation has been conducted on simple airplane-like configurations on a rotary sting apparatus at rotation rates up to 10 rps. Rotary coefficients have been measured at unit Reynolds numbers from 2,000,000 to 24,600,000 per m and at angles of attack from 45 to 90 deg. Results show that the aerodynamic characteristics at steady spin rates are highly dependent on both spin rate and Reynolds number.

Clarkson, M. H.↗

Prediction of span loading of straight-wing/propeller combinations up to stall

A method is presented for calculating the spanwise lift distribution on straight-wing/propeller combinations. The method combines a modified form of the Prandtl wing theory with a realistic representation of the propeller slipstream distribution. The slipstream analysis permits calculations of the nonuniform axial and rotational slipstream velocity field of propeller/nacelle combinations. This nonuniform field was then used to calculate the wing lift distribution by means of the modified Prandtl wing theory. The theory was developed for any number of nonoverlapping propellers, on a wing with partial or full-span flaps, and is applicable throughout an aspect ratio range from 2.0 and higher. A computer program was used to calculate slipstream characteristics and wing span load distributions for a number of configurations for which experimental data are available, and favorable comparisons are demonstrated between the theoretical predictions and the existing data.

Mcveigh, M. A.↗

Investigation of rotor blade element airloads for a teetering rotor in the blade stall regime (second wind tunnel test)

A test was conducted in the NASA-Ames 7 x 10 ft low speed wind tunnel on a seven-foot diameter model of a teetering rotor. The objectives of the test were: (1) acquire pressure data for correlation with laser and flow visualization measurements; (2) explore rotor propulsive force limits by varying the advance ratio at constant lift and propulsive force coefficients; (3) obtain additional data to define the differences between teetering and articulated rotors; and (4) verify the acceleration sensitivity of experimental transducers. Results are presented.

Dadone, L. U.↗

Recent developments in dynamic stall

Tests were performed on an airfoil in a low-turbulence subsonic wind tunnel at fixed incidence for different speeds of the wind, the airfoil being in translatory motion normal or parallel to the wind. The resulting aerodynamic forces and moment on the airfoil were measured along with local pressure and skin friction. When the incidence is small and the boundary layer attached, no unsteady effects were observed. However, for a large incidence (16 deg), in the case of boundary layer separation, strong unsteady effects are revealed when the boundary layer is reattached in periodic flow. Reattachment can be explained assuming that for the same value of free stream velocity, the gradient of the modulus of the periodic component of the relative airspeed at the upper surface of the airfoil in a direction normal to this surface is greater than the gradient of the relative air speed at the upper surface when the airfoil is not oscillating.

Mccroskey, W. J.↗

Numerical solutions of the triple-deck equations for laminar trailing-edge stall

The problem of determining the effect of laminar boundary layers on the lift of thin wings in subsonic flow at high Reynolds numbers is considered. The boundary value problem is formulated in the framework of the triple-deck theory of Brown and Stewartson. The resulting fourth-order boundary value was solved by an iterative finite-difference technique. An inverse iteration procedure provides proper treatment of the trailing-edge singularity, and asymptotic far-field expansions and coordinate stretchings are used to deal with the problem of the slow algebraic decay of the solution.

Chow, R.↗

Studies of flow separation and stalling on one- and two-element airfoils at low speeds

Research has been conducted on the nature of airfoil behavior at pre- and post-separated angles of attack. Detailed wind tunnel studies have been made of boundary layer and wake fields for the GA(W)-1 airfoil, and the airfoil with a 0.3 chord Fowler flap. Experimental data are compared with theoretical predictions from a multi-element viscous flow computer program. Theoretical predictions are reasonably accurate for unseparated flows, but have serious errors when separation is present. Some recent techniques for modeling post-separated flow behavior are discussed in light of the present experiments.

Seetharam, H. C.↗

Analysis of strong-interaction dynamic stall for laminar flow on airfoils

A compressible Navier-Stokes solution procedure is applied to the flow about an isolated airfoil. Two major problem areas were investigated. The first area is that of developing a coordinate system and an initial step in this direction has been taken. An airfoil coordinate system obtained from specification of discrete data points developed and the heat conduction equation has been solved in this system. Efforts required to allow the Navier-Stokes equations to be solved in this system are discussed. The second problem area is that of obtaining flow field solutions. Solutions for the flow about a circular cylinder and an isolated airfoil are presented. In the former case, the prediction is shown to be in good agreement with data.

Gibeling, H. J.↗

Wind tunnel tests of a blade subjected to midchord torsional oscillation at high subsonic stall flutter conditions

A mechanical drive system for oscillating blades in a wind tunnel at frequencies up to 767 hertz and amplitudes of + or - 1.2 deg is described. High-speed motion pictures of schlieren images of the flow over a double-circular arc blade oscillating in harmonic motion about the midchord revealed extensive shock patterns at a nominal free stream Mach number of 0.7, a mean angle of attack of 4 deg, and reduced frequency of about 0.7. A phase lag resulting from the slow response of the flow to the motion of the blade increased with increasing reduced frequency. This phase lag, based on the difference between the time the blade attained its maximum angle of attack and the time required for the normal shock to reach its extreme downstream position, was nominally 100 deg at the above conditions.

Boldman, D. R.↗

Structure of the Turbulent Separated Flow Around a Stalled Airfoil

Hot-wire measurements were made in the boundary layer, the separated region, and the near wake for flow past a NACA 4412 airfoil at maximum lift. The Reynolds number based on chord was 1,500,000. Special care was taken to achieve a two-dimensional mean flow. Data were obtained at several thousand locations in the flow field. These data include intermittency, two components of mean velocity, and mean values for three double, four triple, and five quadruple products of two velocity fluctuations. No information was obtained about the third (spanwise) velocity component. Smoothing and interpolating routines were used to determine intermittency, two components of mean velocity, and mean values of three double, four triple, and five quadruple products of two velocity fluctuations on a fine rectangular mesh aligned with the airfoil chord. The data are presented in contour plots, in three-dimensional plots, and in tabular form. The format used to store the experimental data in digital form is described and a computer program which illustrates how this data can be accessed is presented.

Wadcock, A. J.↗

Effects of steady-state pressure distortion on the stall margin of a J85-21 turbojet engine

The effects of the inlet pressure distortions, induced by five screen patterns, on the performance of a J85-21 turbojet engine was conducted at the NASA Lewis Research Center. Testing was in support of the HiMAT RPRV program at Dryden Flight Research Center. Distortion patterns were chosen based on anticipated application of test results of the HiMAT installation. Tests were conducted at a simulated Mach number and altitude condition of 0.9 and 10 973 meters. Results are presented in terms of distortion levels and standard compressor performance parameters.

Bobula, G. A.↗

Numerical lifting line theory applied to drooped leading-edge wings below and above stall

A numerical iterative solution to the classical Prandtl lifting-line theory, suitably modified for poststall behavior, is used to study the aerodynamic characteristics of straight rectangular finite wings with and without leading-edge droop. This study is prompted by the use of such leading-edge modifications to inhibit stall/spins in light general aviation aircraft. The results indicate that lifting-line solutions at high angle of attack can be obtained that agree with experimental data to within 20%, and much closer for many cases. Therefore, such solutions give reasonable preliminary engineering results for both drooped and undrooped wings in the poststall region. However, as predicted by von Karman, the lifting-line solutions are not unique when sectional negative lift slopes are encountered. In addition, the present numerical results always yield symmetrical lift distributions along the span, in contrast to the asymmetrical solutions observed by Schairer in the late 1930's. Finally, a series of parametric tests at low angle of attack indicate that the effect of drooped leading edges on aircraft cruise performance is minimal.

Anderson, J. D., Jr.↗

Determination of model structure and parameters of an airplane from pre- and post-stall flight data

A procedure for airplane model structure determination from flight data based on modified stepwise regression (MSR), several decision criteria and postulated aerodynamic model equations is presented. The MSR is constructed to force a linear model for the aerodynamic coefficient first, then select significant nonlinear terms and reject nonsignificant terms from the model. In addition to the statistical criteria in the stepwise regression, the prediction sum of squares (PRESS) criterion and analysis of residuals are examined for the selection of an adequate model. The procedure is used in examples with simulated and real flight data. It is shown that the MSR performs better than the ordinary stepwise regression and that the technique can be also applied to the large amplitude maneuvers.

Klein, V.↗

Stalled-Flow and Head-Loss Model for Diffuser Pumps

Modeling procedure approximates inlet transition zone (blade leading edge to blade throat) of diffuser pump as two-dimensional cascade, properties of which are well known. Model applied to stators as well as rotors. Procedure much faster than previous methods.

Meng, S. Y.↗

Comparative evaluation of gas-turbine engine combustion chamber starting and stalling characteristics for mechanical and air-injection

The effectiveness of propellant atomization with and without air injection in the combustion chamber nozzle of a gas turbine engine is studied. Test show that the startup and burning performance of these combustion chambers can be improved by using an injection during the mechanical propellant atomization process. It is shown that the operational range of combustion chambers can be extended to poorer propellant mixtures by combined air injection mechanical atomization of the propellant.

Dyatlov, I. N.↗

Unsteady laminar boundary-layer calculations on oscillating configurations including backflow. Part 2: Airfoil in high-amplitude pitching motion. Dynamic stall

A previously developed finite-difference procedure for calculating unsteady, incompressible, laminar boundary layers on an oscillating flat plate is applied to a wing section undergoing high-amplitude pitching oscillations about various mean incidences. To start the entire boundary-layer calculation, appropriate initial conditions and outer boundary conditions are specified, using a stagnation-point fixed frame of reference. The breakdown of the numerical calculation procedure in the x,t-domain is interpreted to coincide with unsteady separation. Details of the boundary-layer behavior in the vicinity of separation are investigated, and a close analogy between the present results and those for a three-dimensional steady separation is found.

Geissler, W.↗