Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Recrystallization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

Lithium implantation at low temperature in silicon for sharp buried amorphous layer formation and defect engineering

The crystalline-to-amorphous transformation induced by lithium ion implantation at low temperature has been investigated. The resulting damage structure and its thermal evolution have been studied by a combination of Rutherford backscattering spectroscopy channelling (RBS/C) and cross sectional transmission electron microscopy (XTEM). Lithium low-fluence implantation at liquid nitrogen temperature is shown to produce a three layers structure: an amorphous layer surrounded by two highly damaged layers. A thermal treatment at 400 Degree-Sign C leads to the formation of a sharp amorphous/crystalline interfacial transition and defect annihilation of the front heavily damaged layer. After 600 Degree-Sign C annealing, complete recrystallization takes place and no extended defects are left. Anomalous recrystallization rate is observed with different motion velocities of the a/c interfaces and is ascribed to lithium acting as a surfactant. Moreover, the sharp buried amorphous layer is shown to be an efficient sink for interstitials impeding interstitial supersaturation and {l_brace}311{r_brace} defect formation in case of subsequent neon implantation. This study shows that lithium implantation at liquid nitrogen temperature can be suitable to form a sharp buried amorphous layer with a well-defined crystalline front layer, thus having potential applications for defects engineering in the improvement of post-implantation layers quality and for shallow junction formation.

36 MATERIALS SCIENCE↗

Defect mitigation by ion induced amorphousization and solid-phase epitaxy

Ion implantation is a common technique in the semiconductor industry used to modify the electrical properties of materials, usually silicon. Some dopant ions are sufficiently light, such as boron, that they do not create a continuous amorphous layer in silicon over the range of the ions. In the presence of such a layer, most of the ioninduced damage can be removed by solid-phase epitaxy growth (SPEG), which results in recrystallization of the amorphous damage. However, end-of-range defects at the amorphous-crystal interface give rise to threading dislocations during SPEG that degrade the quality of the recrytallized Si. We have studied the end of range defects in silicon with three different implantations. The first was with 80 keV {sup 30}Si with a dose of 3 Multiplication-Sign 10{sup 15} Si/cm{sup 2}, and the second was with 100 keV {sup 72}Ge at a dose of 1 Multiplication-Sign 10{sup 15} Ge/cm{sup 2}, and the third was a double implant of 100 keV {sup 72}Ge at a dose of 1 Multiplication-Sign 10{sup 15} Ge/cm{sup 2} followed by 340 keV {sup 28}Si at a dose of 3 Multiplication-Sign 10{sup 14} Si/cm{sup 2}. SPEG was done at 650 Degree-Sign C to recrystalize the implanted samples, and the end of range defects were studied using channeled Rutherford Backscattering Spectrometry (RBS-c). The effects of photon-assisted hydrogenation on amorphization and recrystallization were also studied.

36 MATERIALS SCIENCE↗

Study of the interaction of solutes with Σ5 (013) tilt grain boundaries in iron using density-functional theory

Substitutional alloying elements significantly affect the recrystallization and austenite-ferrite phase transformation rates in steels. The atomistic mechanisms of their interaction with the interfaces are still largely unexplored. Using density functional theory, we determine the segregation energies between commonly used alloying elements and the Σ5 (013) tilt grain boundary in bcc iron. We find a strong solute-grain boundary interaction for Nb, Mo, and Ti that is consistent with experimental observations of the effects of these alloying elements on delaying recrystallization and the austenite-to-ferrite transformation in low-carbon steels. In addition, we compute the solute-solute interactions as a function of solute pair distance in the grain boundary, which suggest co-segregation for these large solutes at intermediate distances in striking contrast to the bulk.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Suppression of grain growth in nanocrystalline Bi{sub 2}Te{sub 3} through oxide particle dispersions

The strategy of suppressing grain growth by dispersing nanoscale particles that pin the grain boundaries is demonstrated in a nanocrystalline thermoelectric compound. Yttria nanoparticles that were incorporated by mechanical alloying enabled nanocrystalline (i.e., d < 100 nm) Bi{sub 2}Te{sub 3} to be retained up to a homologous temperature of 0.94 T{sub m} for durations over which the grain size of the unreinforced compound grew to several microns. The nanostructure appeared to saturate at a grain size that depended on volume fraction (f) according to an f {sup −1/3} relationship, in accordance with theoretical models in the limit of high volume fractions of particles. Interestingly, at low temperatures, the particles stimulate enhanced grain growth over the unreinforced compound, due to particle-stimulated nucleation of recrystallization. To help prevent this effect, in-situ composites formed by internal oxidation of yttrium are compared with those made ex-situ by incorporation of yttria nanoparticles, with the result that the in-situ dispersion eliminates recrystallization at low temperatures and therefore improves nanostructure stabilization. These developments offer a pathway to thermally stabilized bulk nanocrystalline thermoelectrics processed via a powder route.

36 MATERIALS SCIENCE↗

High dislocation density of tin induced by electric current

A dislocation density of as high as 10{sup 17} /m{sup 2} in a tin strip, as revealed by high resolution transmission electron microscope, was induced by current stressing at 6.5 x 10{sup 3} A/ cm{sup 2}. The dislocations exist in terms of dislocation line, dislocation loop, and dislocation aggregates. Electron Backscattered Diffraction images reflect that the high dislocation density induced the formation of low deflection angle subgrains, high deflection angle Widmanstätten grains, and recrystallization. The recrystallization gave rise to grain refining.

36 MATERIALS SCIENCE↗

Formation mechanism for the nanoscale amorphous interface in pulse-welded Al/Fe bimetallic systems

Pulse or impact welding traditionally has been referred to as “solid-state” welding. By integrating advanced interface characterizations and diffusion calculations, we report that the nanoscale amorphous interface in the pulse-welded Al/Fe bimetallic system is formed by rapid heating and melting of a thin Al layer at the interface, diffusion of iron atoms in the liquid aluminum, and subsequent rapid quenching with diffused iron atoms in solution. This finding challenges the commonly held belief regarding the solid-state nature of the impact-based welding process for dissimilar metals. Elongated ultra-fine grains with high dislocation density and ultra-fine equiaxed grains also are observed in the weld interface vicinity on the steel and aluminum sides, respectively, which further confirms that melting and the subsequent recrystallization occurred on the aluminum side of the interface.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Lead titanate/cyclic carbonate dependence on ionic conductivity of ferro/acrylate blend polymer composites

Impedance, XRD, DSC and FTIR studies had been carried out for PVdF-co-HFP/LIBETI based system for three plasticizer (EC/DMC) – filler (PbTiO3) weight ratios. The enhanced conductivity 4.18 × 10{sup −5} Scm{sup −1} was noted for 57.5 wt% −7.5 wt% plasticizer – filler. while blending PEMA to PVdF-co-HFP respectively 7.5: 22.5 wt % (3/7), 15 wt%: 15 wt % (5/5) and 22.5wt %: 7.5 wt % (7/3), the improved conductivity was noted for 3/7 ratio 1.22 × 10{sup −5} S cm{sup −1} and its temperature dependence abide Arrhenius behavior. The intensity of peaks in XRD diffractogram registered dominance of lead titanate, from 2θ = 10° to 80° and absence of VdF crystallites (α+β phase) was noted. In DSC studies, the presence of the exotherm events, filler effect was distinctively seen exhibiting recrystallization of VdF crystallites. In blending PEMA, however, no trace of exotherms was found suggestive of PEMA better inhibiting recrystallization. FTIR study confirmed molecular interactions of various constituents in the vibrational band 500 – 1000 cm{sup −1} both in pristine PVdF-co-HFP and PEMA blended composites with reference to C-F stretching, C-H stretching and C=O carbonyl bands.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The Influence of Microstructure on Deuterium Retention in Polycrystalline Tungsten

The retention of hydrogen isotopes in the plasma-facing materials of a fusion reactor is dependent on the density of trapping sites in the material. One factor that can influence the trapping defects is the surface state of the material before exposure. Mechanically polished, electropolished, and recrystallized tungsten samples were compared by exposing them to 350 eV D + beams with peak fluences of ~1 × 10 24 D + /m 2 at 500 and 740 K at the Multicharged Ion Research Facility (MIRF). At the exposure temperature of 740 K, no significant retention was detected. For material exposed at 500 K, significant differences in retention were observed, and the order of increasing retention was recrystallized, electropolished, and mechanically polished. Lastly, the other variable besides surface treatment was the time delay between ion exposure and thermal desorption spectroscopy which also may have impacted the retention measurements if there was out-gassing of the D while samples were in storage before thermal desorption spectroscopy (TDS).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Interstitial hydrogen enhances the mobility of some grain boundaries in tungsten

Segregation of interstitials at a grain boundary (GB) is known to generally lower its mobility. This phenomenon, called 'solute-drag', has important ramifications on the process of recrystallization and microstructural evolution. Here, we present predictions from molecular dynamics (MD) simulations which demonstrate that interstitial hydrogen in tungsten can in fact increase the mobility of some GBs which exhibit shear coupling. Assuming a disconnection-based mechanism, activation energies and pre-factors for disconnection nucleation are predicted from simulations of shear-coupled motion. In GBs where enhanced mobility is predicted, interstitial H reduces both the activation energy and the pre-factor for disconnection nucleation, thus effectively increasing the mobility. For GBs with diminished mobility, MD predicts that presence of interstitial H reduces the pre-factor and, in some cases, increases the activation energy. The reduction in the activation energy inferred from MD simulations are confirmed by nudged elastic band calculations. Temperature-dependent structural transitions are observed for some GBs, and the effect of interstitial H is found to change with the changes in structure. The effect of interstitial H is predicted to be complex and highly variable, providing some plausible explanations for experimental observations on the recrystallization of tungsten in presence of H-loaded plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Study of Indium Chloride Vapor Treatment on Cu(In,Ga)Se 2 Semiconductor Thin Films

The recrystallization by indium chloride of Cu(In,Ga)Se 2 thin films deposited by co-evaporation at 350°C was studied. The process of recrystallization consists of the postdeposition treatment of CIGS sample by InCI3 vapor for 30 minutes with emphasis on grain growth. Here, the treatment resulted in uniform increased grain size and improved crystallinity. XRD measurements suggests the formation of indium rich phase. Dynamic SIMS were also performed to further understand the process, phase separation and the extent of gallium depletion.

14 SOLAR ENERGY↗

Changes induced in a ZnS:Cr-based electroluminescent waveguide structure by intrinsic near-infrared laser radiation

The causes of changes that occur in a thin-film electroluminescent metal-insulator-semiconductor-insulator-metal waveguide structure based on ZnS:Cr (Cr concentration of {approx}4 Multiplication-Sign 10{sup 20} cm{sup -3}) upon lasing ({lambda} Almost-Equal-To 2.6 {mu}m) and that induce lasing cessation are studied. It is established that lasing ceases because of light-scattering inhomogeneities formed in the structure and, hence, optical losses enhance. The origin of the inhomogeneities and the causes of their formation are clarified by studying the surface topology and the crystal structure of constituent layers of the samples before and after lasing. The studies are performed by means of atomic force microscopy and X-ray radiography. It is shown that a substantial increase in the sizes of grains on the surface of the structure is the manifestation of changes induced in the ZnS:Cr film by recrystallization. Recrystallization is initiated by local heating by absorbed laser radiation in existing Cr clusters and quickened by a strong electric field (>1 MV cm{sup -1}). The changes observed in the ZnS:Cr film are as follows: the textured growth of ZnS crystallites, an increase in the content of Cr clusters, and the appearance of some CrS and a rather high ZnO content. Some ways for improving the stability of lasing in the ZnS:Cr-based waveguide structures are proposed.

36 MATERIALS SCIENCE↗

Crystal defects in solar cells produced by the method of thermomigration

The results of studying the crystal structure of regions in silicon, recrystallized during the course of thermomigration of the liquid Si–Al zone in the volume of the silicon substrate, are reported (similar regions doped with an acceptor impurity are used to obtain high-voltage solar cells). X-ray methods (including measurements of both diffraction-reflection curves and topograms) and also high-resolution electron microscopy indicate that single-crystal regions in the form of a series of thin strips or rectangular grids are formed as a result of the thermomigration of liquid zones. Dislocation half-loops are detected in the surface layers of the front and back surfaces of the substrate. (311)-type defects are observed in the recrystallized regions.

14 SOLAR ENERGY↗

Testing of Performance of Optical Fibers Under Irradiation in Intense Radiation Fields, When Subjected to Very High Temperatures

The primary objective of this project is to measure and model the performance of optical fibers in intense radiation fields when subjected to very high temperatures. This research will pave the way for fiber optic and optically based sensors under conditions expected in future high-temperature gas-cooled reactors. Sensor life and signal-to-noise ratios are susceptible to attenuation of the light signal due to scattering and absorbance in the fibers. This project will provide an experimental and theoretical study of the darkening of optical fibers in high-radiation and high-temperature environments. Although optical fibers have been studied for moderate radiation fluence and flux levels, the results of irradiation at very high temperatures have not been published for extended in-core exposures. Several previous multi-scale modeling efforts have studied irradiation effects on the mechanical properties of materials. However, model-based prediction of irradiation-induced changes in silica's optical transport properties has only recently started to receive attention due to possible applications as optical transmission components in fusion reactors. Nearly all damage-modeling studies have been performed in the molecular-dynamics domain, limited to very short times and small systems. Extended-time modeling, however, is crucial to predicting the long-term effects of irradiation at high temperatures, since the experimental testing may not encompass the displacement rate that the fibers will encounter if they are deployed in the VHTR. The project team will pursue such extended-time modeling, including the effects of the ambient and recrystallization. The process will be based on kinetic MC modeling using the concept of amorphous material consisting of building blocks of defect-pairs or clusters, which has been successfully applied to kinetic modeling in amorphized and recrystallized silicon. Using this procedure, the team will model compensation for rate effects, and the interplay of rate effects with the effects of annealing, to accurately predict the fibers' reliability and expected lifetime

36 MATERIALS SCIENCE↗

Radiation behavior of high-entropy alloys for advanced reactors. Final report

In the first task, we have demonstrated the radiation damage and the recrystallization behaviors in multicomponent alloys through molecular-dynamics simulations. It is found that by alloying with atoms of different sizes, the atomic-level strain increases, and the propensity of the radiation-induced crystalline to amorphous transition increases as the defects cluster in the cascade body. Recrystallization of the radiation induced supercooled or glass regions show that by tuning the composition and the equilibrium temperature, the multicomponent alloys can be healed. The crystalline-amorphous-crystalline transitions predict the potential high radiation resistance in multicomponent alloys. In the second task, three types of high-entropy alloys (HEAs) were fabricated from AlCoCrFeNi and AlCuCrFeNi quinary alloys. Hardness and reduced contact modulus were measured using nanoindentation tests. Heavy ion irradiation were performed using 10 MeV gold and 5 MeV nickel to study radiation effects. Al 0.5 CrCuFeNi 2 shows phase separation upon the presence of copper. Both hardness and contact modulus exhibit the same trend as increasing the applied load, and it indicates that excessive free volume may alter the growth rate of the plastic zone. The as-cast Al 0.1 CoCrFeNi specimen undergone the hot isostatic pressing (HIP) process and steady cooling rate which mitigate the quenching effect. The swelling behavior was characterized by the atomic force microscopy (AFM), and the swelling rate is approximately 0.02% dpa. Selected area diffraction (SAD) patters show irradiation-induced amorphization throughout the ion projected range. Within the peak damage region, an amorpous ring is observed, and a mixture of amorphous/ crystalline structure at deeper depth is found. The Al 0.3 CoCrFeNi HEAs shows good radiation resistance up to 60 peak dpa. No voids or dislocations are observed. The crystal structures remain face-centered-cubic (FCC) before and after 5 MeV Ni irradiation. Higher dpa might be required to study defects formation mechanisms. In the third task, all the constituent binary and ternary systems of the Al-Co-Cr-Fe-Ni system were thermodynamically modeled within the whole composition range. Comparisons between the calculated phase diagrams and literature data are in good agreement. The multi-component thermodynamic database of the Al-Co-Cr-Fe-Ni system was then obtained via extrapolation. The current Al-Co-Cr-Fe-Ni thermodynamic database enables us to carry out the calculations of phase diagrams, which can be used as useful guidelines to identify the Al-Co-Cr-Fe-Ni HEAs with desirable microstructures. In the fourth task, we discuss how as-cast and homogenized phases can be identified, what phases are usually found in the as-cast and homogenized conditions, and what the thermodynamics and kinetics of phase transformations are in the AlCoCrFeNi HEA. The microstructure and phase composition were studied in as-cast and homogenized conditions. It showed the dendritrical structure in the as-cast condition consisting primarily of a nano-lamellar mixture of A2 [disorder body-centered-cubic (BCC)] and B2 (ordered BCC) phases, in addition to a very small amount of A1 [disorder face-centered-cubic (FCC)] phases. The homogenization heat treatment resulted in an increase in the volume fraction of the A1 phase and formation of a Sigma phase. Tensile properties in as-cast and homogenized conditions are reported at 700 °C. Thermodynamic modeling of non-equilibrium and equilibrium phase diagrams for the AlCoCrFeNi HEA gave good agreement with the experimental observations of the phase contents. The reasons for the improvement of ductility after the heat treatment are discussed.

36 MATERIALS SCIENCE↗

Electron Microscopy Study of Hypo-Stoichiometric Fe-Pd Nanocomposites Resulting from Combined Reaction Thermomechanical Processing

Hypo stoichiometric Fe-Pd binary alloys (35-45 at% Pd) were severely deformed (>90%) and subsequently aged to induce concomitant recrystallization, precipitation, and ordering. This thermomechanical processing strategy was articulated by Hornbogen [1] over thirty years ago. The resulting exchange-coupled ferromagnets contain ferrite precipitates and a complex metastable twophase lamellar transformation product comprised of ordered L10 and a metastable FCC phase. The later duplex microconstituent is suggested to form in conjunction with a so-called pseudospinodal reaction [2] involving emerging cubic and tetragonal phases, whereby phase separation and ordering result from continuous changes in composition and a reduction in symmetry, cubic to tetragonal. The deformation texture of the parent austenite is substantially retained in the transformation product, resulting in anisotropy of the magnetic properties as determined by magnetometry (VSM). This paper presents electron microscopy results elucidating the crystallography and morphology of the phase mixtures including HREM. Magnetic field annealing is also included as a branch of our thermomechanical processing strategy, and we discuss the influence of the external fields on recrystallization, precipitation, and ordering. This work was performed in cooperation with ORNL and the NHMFL and is supported by the NSF DMR.

36 MATERIALS SCIENCE↗

The role of crystallography and nanostructures on metallic friction.

In ductile metals, sliding contact is often accompanied by severe plastic deformation localized to a small volume of material adjacent to the wear surface. During the initial run-in period, hardness, grain structure and crystallographic texture of the surfaces that come into sliding contact undergo significant changes, culminating in the evolution of subsurface layers with their own characteristic features. Here, a brief overview of our ongoing research on the fundamental phenomena governing the friction-induced recrystallization in single crystal metals, and how these recrystallized structures with nanometer-size grains would in turn influence metallic friction will be presented. We have employed a novel combination of experimental tools (FIB, EBSD and TEM) and an analysis of the critical resolved shear stress (RSS) on the twelve slip systems of the FCC lattice to understand the evolution of these friction-induced structures in single crystal nickel. The later part of the talk deals with the mechanisms of friction in nanocrystalline Ni films. Analyses of friction-induced subsurfaces seem to confirm that the formation of stable ultrafine nanocrystalline layers with 2-10 nm grains changes the deformation mechanism from the traditional dislocation mediated one to that is predominantly controlled by grain boundaries, resulting in significant reductions in the coefficient friction.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

In situ laser-based resonant ultrasound measurements of microstructure mediated mechanical property evolution

In situ laser-based resonant ultrasound spectroscopy is used to characterize the development of a recrystallized microstructure in a high purity copper sample. The modal shapes, used for mode identification, of several resonant modes are determined before and after annealing by raster scanning the laser interferometric probe. This information is used to isolate the motion of individual modes during high temperature annealing. The evolution of a particular mode during annealing is examined in detail. During recrystallization, the center frequency of this mode shifts by approximately 20% of the original value. Using electron backscatter data it is shown that the majority of this shift is due to changes in the polycrystal average elastic stiffness tensor, driven by changes in texture, and that changes in dislocation density and pinning length are secondary influences.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Electron Microscopy Characterizations and Atom Probe Tomography of Intergranular Attack in Alloy 600 Exposed to PWR Primary Water

Detailed examinations of intergranular attack (IGA) in alloy 600 were performed after exposure to simulated PWR primary water at 325°C for 500 h. High-resolution analyses of IGA characteristics were conducted on specimens with either a 1 µm diamond or 1200-grit SiC surface finish using scanning electron microscopy, transmission electron microscopy and atom probe tomography techniques. The diamond-polish finish with very little preexisting subsurface damage revealed attack of high-energy grain boundaries that intersected the exposed surface to depths approaching ~2 µm. In all cases, IGA from the surface is localized oxidation consisting of porous, nanocrystalline MO-structure and spinel particles along with regions of faceted wall oxidation. Surprisingly, this continuous IG oxidation transitions to discontinuous, discrete Cr-rich sulfide particles up to ~50 nm in diameter. In the vicinity of the sulfides, the grain boundaries were severely Cr depleted (to <1 at%) and enriched in S. The 1200 grit SiC finish surface exhibited a preexisting highly strained recrystallized layer of elongated nanocrystalline matrix grains. Similar IG oxidation and leading sulfide particles were found, but the IGA depth was typically confined to the near-surface (~400 nm) recrystallized region. Difference in IGA for the two surface finishes indicates that the formation of grain boundary sulfides occurs during the exposure to PWR primary water. The source of S remains unclear, however it is not present as sulfides in the bulk alloy nor is it segregated to bulk grain boundaries.

Olszta, Matthew J.↗