Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Rechargeable batteries”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Membrane-Free Zn/MnO 2 Flow Battery for Large-Scale Energy Storage

The traditional Zn/MnO 2 battery has attracted great interest due to its low cost, high safety, high output voltage, and environmental friendliness. However, it remains a big challenge to achieve long-term stability, mainly owing to the poor reversibility of the cathode reaction. Different from previous studies where the cathode redox reaction of MnO 2 /MnOOH is in solid state with limited reversibility, in this work a new aqueous rechargeable Zn/MnO 2 flow battery is constructed with dissolution–precipitation reactions in both cathodes (Mn 2+ /MnO 2 ) and anodes (Zn 2+ /Zn), which allow mixing of anolyte and catholyte into only one electrolyte and remove the requirement for an ion selective membrane for cost reduction. Impressively, this new battery exhibits a high discharge voltage of ≈1.78 V, good rate capability (10C discharge), and excellent cycling stability (1000 cycles without decay) at the areal capacity ranging from 0.5 to 2 mAh cm -2 . More importantly, this battery can be readily enlarged to a bench scale flow cell of 1.2 Ah with good capacity retention of 89.7% at the 500th cycle, displaying great potential for large-scale energy storage.

25 ENERGY STORAGE↗
DOE OSTI2023

A room temperature rechargeable Li 2 O-based lithium-air battery enabled by a solid electrolyte

Lithium-air batteries have scope to compete with gasoline in terms of energy density. However, in most systems, the reaction pathways either involve one- or two-electron transfer, leading to lithium peroxide (Li 2 O 2 ) or lithium superoxide (LiO 2 ), respectively. Kondori et al. investigated a lithium-air battery that uses a ceramic-polyethylene oxide–based composite solid electrolyte and found that it can undergo a four-electron redox reaction through lithium oxide (Li 2 O) formation and decomposition (see the Perspective by Dong and Lu). The composite electrolyte embedded with Li 10 GeP 2 S 12 nanoparticles shows high ionic conductivity and stability and high cycle stability through a four-electron transfer process.

25 ENERGY STORAGE↗
DOE OSTI2026

State-of-Charge Investigation of Lithium Manganese Dioxide Primary Batteries Utilizing X-ray Computed Tomography

Lithium primary batteries (LPBs) represent a class of energy storage devices, uniquely suited for mission-critical applications including emergency backup power, aerospace and defense electronics, implantable medical devices, and remote sensing. Despite their technological maturity and distinct advantages over rechargeable lithium-ion batteries (i.e., superior shelf life and operational simplicity), state-of-charge (SoC) estimation in these batteries remains a persistent challenge due to the lack of a reliable, quantifiable diagnostic technique. In this work, we investigate X-ray computed tomography (X-CT) as a transformative and accurate SoC estimation technique for LPBs. Results gained through X-CT measurements reveal systematic, quantifiable structural changes in cathode morphology and geometry during discharge, establishing a direct structural basis for SoC estimation, with a maximum relative standard deviation of 2.3%. This work establishes a pathway toward operando, imaging-driven SoC diagnostics that can significantly enhance the reliability of SoC estimation in LPBs.

25 ENERGY STORAGE↗
DOE OSTI2023

Tuning Discharge Behavior of Hollandite α-MnO 2 in Hydrated Zinc Ion Battery by Transition Metal Substitution

The tunnel-type hollandite α-MnO 2 is a promising cathode material for rechargeable aqueous zinc-ion batteries (ZIBs) due to its low cost in synthesis and high energy density. However, irreversible structural degradation upon continuous cycling prevents the cathode from being utilized commercially. Herein, density functional theory (DFT) was utilized to conduct a systematic study on tuning the behavior of α-MnO 2 by substituting the Mn ions on the tunnel wall with a transition metal (V or Cr) during the H + -/Zn 2+ -intercalation in hydrated ZIB. Our study revealed that both substituents aid cyclability and capacity retention with Cr outperforming V. In term of discharge voltage, only the Cr-substitution displays clear promotion at the early stage of discharge. The superior performance of substituted Cr 4+ comes from its unique atomic and electronic structures. Upon discharge, it can be reduced to Cr 3+ more readily than Mn 4+ and thereby limits the formation of unstable Mn 3+ or Mn 2+ centers; the formed Cr 3+ is more stable than Mn 3+ and Mn 2+ from the reduction of Mn 4+ ; and Cr 3+ can also greatly stabilize the neighboring Mn ions. Here this study highlights the significant tuning effect of transition metal substitution on the electrochemical and physical performance of α-MnO 2 as a cathode in hydrated ZIBs.

25 ENERGY STORAGE↗
DOE OSTI2020

From K‐O 2 to K‐Air Batteries: Realizing Superoxide Batteries on the Basis of Dry Ambient Air

Abstract Although using an air cathode is the goal for superoxide‐based potassium‐oxygen (K‐O 2 ) batteries, prior studies were limited to pure oxygen. Now, the first K‐air (dry) battery based on reversible superoxide electrochemistry is presented. Spectroscopic and gas chromatography analyses are applied to evaluate the reactivity of KO 2 in ambient air. Although KO 2 reacts with water vapor and CO 2 to form KHCO 3 , it is highly stable in dry air. With this knowledge, rechargeable K‐air (dry) batteries were successfully demonstrated by employing dry air cathode. The reduced partial pressure of oxygen plays a critical role in boosting battery lifespan. With a more stable environment for the K anode, a K‐air (dry) battery delivers over 100 cycles (>500 h) with low round‐trip overpotentials and high coulombic efficiencies as opposed to traditional K‐O 2 battery that fails early. This work sheds light on the benefits and restrictions of employing the air cathode in superoxide‐based batteries.

Qin, Lei↗
DOE OSTI2024

A Review of Nanocarbon-Based Anode Materials for Lithium-Ion Batteries

Renewable and non-renewable energy harvesting and its storage are important components of our everyday economic processes. Lithium-ion batteries (LIBs), with their rechargeable features, high open-circuit voltage, and potential large energy capacities, are one of the ideal alternatives for addressing that endeavor. Despite their widespread use, improving LIBs’ performance, such as increasing energy density demand, stability, and safety, remains a significant problem. The anode is an important component in LIBs and determines battery performance. To achieve high-performance batteries, anode subsystems must have a high capacity for ion intercalation/adsorption, high efficiency during charging and discharging operations, minimal reactivity to the electrolyte, excellent cyclability, and non-toxic operation. Group IV elements (Si, Ge, and Sn), transition-metal oxides, nitrides, sulfides, and transition-metal carbonates have all been tested as LIB anode materials. However, these materials have low rate capability due to weak conductivity, dismal cyclability, and fast capacity fading owing to large volume expansion and severe electrode collapse during the cycle operations. Contrarily, carbon nanostructures (1D, 2D, and 3D) have the potential to be employed as anode materials for LIBs due to their large buffer space and Li-ion conductivity. However, their capacity is limited. Blending these two material types to create a conductive and flexible carbon supporting nanocomposite framework as an anode material for LIBs is regarded as one of the most beneficial techniques for improving stability, conductivity, and capacity. This review begins with a quick overview of LIB operations and performance measurement indexes. It then examines the recently reported synthesis methods of carbon-based nanostructured materials and the effects of their properties on high-performance anode materials for LIBs. These include composites made of 1D, 2D, and 3D nanocarbon structures and much higher Li storage-capacity nanostructured compounds (metals, transitional metal oxides, transition-metal sulfides, and other inorganic materials). The strategies employed to improve anode performance by leveraging the intrinsic features of individual constituents and their structural designs are examined. The review concludes with a summary and an outlook for future advancements in this research field.

25 ENERGY STORAGE↗
DOE OSTI2023

Understanding the reversible electrodeposition of aluminum in low-cost room-temperature molten salts

Aluminum is the most earth-abundant metal, trivalent, and inert in ambient air; it also has a density approximately five times that of lithium at room temperature, making it attractive for cost-effective, long-duration storage in batteries. Here, we investigate structural requirements and physicochemical and transport properties of ionic liquid (IL) electrolytes thought to enable high reversibility of Al battery anodes. We find that intentionally designed, low-cost IL analogs, including ammonium-based molten salts, offer comparable Al anode reversibility to state-of-the-art imidazolium-based IL melts. A critical ratio of solvated Al-ion species is required to balance the effects of Lewis acidity needed to continuously etch native Al 2 O 3 and form a stable solid electrolyte interphase on Al. Our findings open new opportunities for developing simple, cost-effective, room-temperature Al batteries that enable long-duration electrical energy storage.

25 ENERGY STORAGE↗
DOE OSTI2024

Structural and chemical evolutions of a magnesium vanadium oxide cathode under electrochemical cycling in magnesium batteries

The design of cathode materials that remain chemically and structurally stable during repetitive ion insertion and extraction poses a significant challenge in developing multivalent batteries. The cycling stability of traditional metal oxide-based cathode is challenged by sluggish diffusion of multivalent cations and parasitic reactivity at interfacial regimes, including the cathode electrolyte interphase layer (CEI). Understanding the reactions at the cathode-electrolyte interface, particularly those induced by non-stoichiometric surface layers, is a crucial design parameter for both cathode materials and electrolytes. Here, in this study, we employed multimodal analysis, including in situ and ex situ X-ray photoelectron spectroscopy (XPS), high resolution transmission electron microscopy (TEM) and electrochemical impedance spectroscopy (EIS) to examine the surface reactions and subsequent structural and chemical evolutions of the CEI on high voltage magnesium vanadium oxide (MgV 2 O 4 ) spinel cathode during the Mg 2+ insertion/extraction processes. The results revealed that the presence of non-stoichiometric surface layers in the magnesium vanadium oxide cathode drive the decomposition of bis(trifluoromethanesulfonyl)imide (TFSI - ) anion, leading to the formation of the CEI layer. The CEI layer could inhibit the Mg 2+ ion transfer processes. Accompanying this reactivity-driven degradation, the magnesium vanadium oxide cathode undergoes pulverization, forming clusters of nanosized particles. This process likely improves cycling ability by creating new intercalation sites and shortening the diffusion pathway for the Mg 2+ cations. This study demonstrates that controlling surface stoichiometry and engineering morphological properties are critical design parameters for high performance cathodes for multivalent batteries.

25 ENERGY STORAGE↗
DOE OSTI2024

Lithium inventory tracking as a non-destructive battery evaluation and monitoring method

Tracking the active lithium (Li) inventory in an electrode shows the true state of a Li battery, akin to a fuel gauge for an engine. However, non-destructive Li inventory tracking is currently unavailable. Here, in this work, we used the theoretical capacity of a transition metal oxide to convert capacity into a Li inventory analysis. The Li inventory in electrodes was tracked reliably to show how battery formulations and test methods affect performance. Contrary to capacity, Li inventory tracking reveals stoichiometric variations near the electrode–electrolyte interface. Verifiable results rationalized differences in measurements, clarifying and reducing interferences from cell formulations and experimental manipulations. By tracing four variables from formation to end-of-life, we characterize electrode and cell performance with a thermodynamic framework. Accurate rationalization of subtle differences in Li inventory utilization promises precise battery engineering, evaluation, failure analysis and risk mitigation. The method could be applicable from cell design optimization and fabrication to battery management, improving battery performance and reliability.

25 ENERGY STORAGE↗
DOE OSTI2021

Redefining Resource Adequacy for Modern Power Systems: A Report of the Redefining Resource Adequacy Task Force

Today's rapidly increasing levels of wind, solar, storage, and load flexibility require the industry to rethink reliability planning and resource adequacy methods for modern power systems. Periods with a risk of shortfall often no longer coincide with peak demand - reliability risks are less about peak load and more about the daily setting of the sun, extended cloud cover, wind speeds, cold snaps, and heat waves. In addition, demand is increasingly flexible. Key resources are time-sensitive, as batteries need time to recharge and electricity customers can only be asked to provide demand response for just so long. And reliability failures are often correlated - with one another and with the weather. Two driving factors require the industry to reconsider its analytical approach for resource adequacy: (1) Chronological grid operations: The increasing importance of variable renewable resources (such as wind and solar) and of energy-limited resources (storage and demand response) make it essential to understand the full year of chronological operation of the grid. Specific attention must be paid to hourly, seasonal, and inter-annual resource variability. The sequence of the variability is key, as energy-limited resources such as batteries or demand response require either a preceding period or subsequent period of high production to be useful for grid reliability. (2) Correlated events: Historically, resource adequacy analysis focused on shortfalls caused by random, discrete mechanical failures of large generating units. In contrast, shortfalls today are often caused by multiple, correlated events caused by common weather patterns. Resource adequacy analysis must increasingly shift its focus to these correlated events. The redesign of resource adequacy methods will benefit from a set of guiding principles to better allow for sharing of insights and best practices, interregional resource coordination, and a smoother regulatory process for resource procurement. The objective of this report is to move this redesign forward. It provides an overview of key drivers changing the way resource adequacy needs to be evaluated, identifies shortcomings of conventional approaches, and outlines first principles for practitioners to consider as they adapt their approaches. The central message is: what got us here won't get us there.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2024

Sucrose‐Based Dense, Pure, and Highly‐Crystalline Graphitic Materials for Lithium‐Ion Batteries

At present, most synthetic graphite materials commonly used as anode active ingredients in lithium-ion cells are produced by graphitization of petroleum cokes. The carbon footprint associated with synthetic graphite production is significant. Thus, bio-derived and cheap precursors, such as saccharides, would be an attractive alternative for the sustainable production of graphitic carbons. However, they are non-graphitizing at temperatures as high as 3000 °C, preserving the curved, fullerene-like structure of graphene layers and microporosity. Consequently, many lithium ions are consumed during the formation of solid electrolyte interphase films and passivated in the nanovoids. Here, a method for the production of pure, crystalline, graphitic materials based on sucrose disposed of microporosity is presented, which also works with a variety of saccharides and other organic precursors of hard carbons—generally considered incapable of such transformation. This process employs catalytic graphitization by Si particles at high temperatures. Finally, the electrochemical response of such derived sucrose-based graphite in Li-ion half-cells demonstrated its feasibility to serve as an anode active material for rechargeable Li-ion batteries.

Si particles↗
DOE OSTI2024

Hydrogen Production and Li-Ion Battery Performance with MoS2-SiNWs-SWNTs@ZnONPs Nanocomposites

This study explores the hydrogen generation potential via water-splitting reactions under UV-vis radiation by using a synergistic assembly of ZnO nanoparticles integrated with MoS2, single-walled carbon nanotubes (SWNTs), and crystalline silicon nanowires (SiNWs) to create the MoS2-SiNWs-SWNTs@ZnONPs nanocomposites. A comparative analysis of MoS2 synthesized through chemical and physical exfoliation methods revealed that the chemically exfoliated MoS2 exhibited superior performance, thereby being selected for all subsequent measurements. The nanostructured materials demonstrated exceptional surface characteristics, with specific surface areas exceeding 300 m2 g−1. Notably, the hydrogen production rate achieved by a composite comprising 5% MoS2, 1.7% SiNWs, and 13.3% SWNTs at an 80% ZnONPs base was approximately 3909 µmol h−1g−1 under 500 nm wavelength radiation, marking a significant improvement of over 40-fold relative to pristine ZnONPs. This enhancement underscores the remarkable photocatalytic efficiency of the composites, maintaining high hydrogen production rates above 1500 µmol h−1g−1 even under radiation wavelengths exceeding 600 nm. Furthermore, the potential of these composites for energy storage and conversion applications, specifically within rechargeable lithium-ion batteries, was investigated. Composites, similar to those utilized for hydrogen production but excluding ZnONPs to address its limited theoretical capacity and electrical conductivity, were developed. The focus was on utilizing MoS2, SiNWs, and SWNTs as anode materials for Li-ion batteries. This strategic combination significantly improved the electronic conductivity and mechanical stability of the composite. Specifically, the composite with 56% MoS2, 24% SiNWs, and 20% SWNTs offered remarkable cyclic performance with high specific capacity values, achieving a complete stability of 1000 mA h g−1 after 100 cycles at 1 A g−1. These results illuminate the dual utility of the composites, not only as innovative catalysts for hydrogen production but also as advanced materials for energy storage technologies, showcasing their potential in contributing to sustainable energy solutions.

Chemistry↗
DOE OSTI2025

A Modified Sand’s Time Incorporating Li-Ion Transport Across the SEI: Basis for Understanding Li Dendrite Formation and Li-Metal Battery Electrolyte Selection

Abstract Understanding the initiation of lithium dendrites remains elusive, largely due to the intricate role of the solid electrolyte interphase (SEI) which forms on the Li surface during electrodeposition. Many studies have utilized the classical Sand’s equation to estimate the onset time when lithium dendrites begin to form. The Sand’s equation provides the time when the cation (Li+) concentration at the electrode-electrolyte interface approaches zero under diffusion-limited conditions in galvanostatic Li electrodeposition. However, recent experimental studies have revealed that the observed lithium dendrite onset time deviates considerably from the Sand’s time. Here, we show that this deviation from classical theory is likely due to the transport of Li+ ions through the SEI - a transport limitation that is much more dominant in controlling dendrite formation. We develop a ‘modified’ Sand's equation, incorporating the SEI layer and the diffusional transport across it to predict Li dendrite onset times. To validate this approach, we conducted Li electrodeposition experiments at various current densities using two distinct organic electrolytes. Analysis of the results demonstrates that the modified Sand's equation provides a more accurate prediction of dendrite onset times, highlighting the importance of incorporating SEI into transport models of Li plating in next-generation rechargeable Li-metal batteries.

Ma, Yuanman (ORCID:0000000200444811)↗
DOE OSTI2020

Enabling Highly Stable Li–O 2 Batteries with Full Discharge–Charge Capability: The Porous Binder- and Carbon-Free IrNi Nanosheet Cathode

Rechargeable aprotic Li-O 2 batteries have drawn much attention in light of their ultrahigh theoretical energy density. However, the sluggish kinetics of oxygen cathode reactions lead to huge energy loss, while the unfavorable side reactions associated with the widely used carbon and binder account for fast battery decay during cycles. In this work, hierarchically holey IrNi alloy nanosheets are facilely designed on Ni foam substrate as a freestanding, binder- and carbon-free cathode to address these challenges. The IrNi nanosheets consist of numerous interconnected nanoparticles, forming abundant nanoholes, benefiting active-site exposure. Moreover, the meso-/macropores pave channels for the transfer of oxygen and lithium ions and provide enough accommodation for the insoluble Li 2 O 2 product. The corresponding Li-O 2 batteries demonstrate low polarization and excellent cycle stability with full discharge/charge capability (up to 292 cycles at a current density of 0.2 mA cm -2 within a voltage range from 2.3 to 4.3 V). The long-term cycling performance is principally attributed to the exclusive catalytic stability of the holey IrNi nanosheets and its good compatibility with dimethyl sulfoxide-based electrolyte. Our research provides novel insights into the design of robust and freestanding porous cathodes for high energy density Li-O 2 batteries.

25 ENERGY STORAGE↗
DOE OSTI2022

Early Failure of Lithium–Sulfur Batteries at Practical Conditions: Crosstalk between Sulfur Cathode and Lithium Anode

Lithium–sulfur (Li–S) batteries are one of the most promising next-generation energy storage technologies due to their high theoretical energy and low cost. However, Li–S cells with practically high energy still suffer from a very limited cycle life with reasons which remain unclear. Here, through cell study under practical conditions, it is proved that an internal short circuit (ISC) is a root cause of early cell failure and is ascribed to the crosstalk between the S cathode and Li anode. The cathode topography affects S reactions through influencing the local resistance and electrolyte distribution, particularly under lean electrolyte conditions. The inhomogeneous reactions of S cathodes are easily mirrored by the Li anodes, resulting in exaggerated localized Li plating/stripping, Li filament formation, and eventually cell ISC. Manipulating cathode topography is proven effective to extend the cell cycle life under practical conditions. The findings of this work shed new light on the electrode design for extending cycle life of high-energy Li–S cells, which are also applicable for other rechargeable Li or metal batteries.

25 ENERGY STORAGE↗
DOE OSTI2023

Hierarchical Cellulose Superinsulation Membrane

The environment-friendly components coupled with the ability to mimic the simplicity and originality of nature necessitate advanced sustainable materials with structural capabilities for energy-efficient applications. The use of feedstock deriving from plant-based, renewable organic material to produce nanofibril that embodies enhanced insulating properties and high mechanical strength constitutes an efficient development strategy. In this work, a free-standing, hierarchical superinsulation membrane by leveraging the principle of the bottom-up method is reported. The electrospun cellulose nanofibrils/aerogel-based core layer provides exceptional thermal properties with its thermal conductivity of 10.2 mW m –1 K –1 . The lightweight, flexible, and durable paper-like membrane features a tensile strength of 11.3 MPa and a bending rigidity in the order of 4.6 cN mm –1 . The hydrophobic superinsulation membrane material also exhibits a ΔT of ≈25 °C under continuous sunlight illumination and allows thermal runaway mitigation of rechargeable lithium-ion batteries. All the aforementioned properties position this hybrid superinsulation membrane as a promising material for energy-saving thermal management applications.

36 MATERIALS SCIENCE↗