Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Quenching”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

Achieving Excellent Strength–Ductility and Impact Toughness Combination by Cyclic Quenching in Medium Mn TRIP-Aided Steel

A novel heat treatment process combined cyclic quenching (CQ) with austenite reversion treatment (ART) is proposed to obtain high strength–ductility and high-impact toughness combination in Fe-0.18C-8.92Mn-3.43Al (in mass%) steel. The process referred as CQ-ART was designed for accomplishing the following objectives: (i) refine the prior austenite grains during cyclic quenching process, (ii) further obtain the refined austenite–ferrite block and (iii) improve the stabilities of retained austenite with Mn/C enrichment during ART process. The outstanding product of tensile strength and total elongation of CQ-ART-treated steels was 41.53 and 37.39 GPa%, respectively, and higher than the ART steel of 27.45 GPa%. The highest Charpy impact toughness of CQ-ART steel can reach to 221 J, which is mainly attributed to the refined grains and discontinuous transformation-induced plasticity (TRIP) effect.

36 MATERIALS SCIENCE↗

Computational analysis of flame initiation, quenching, and re-ignition in a prechamber natural gas engine under varying EGR-dilution levels

The on-road natural-gas (NG) fueled transportation relies on stoichiometric spark-ignition engines for the advantages of simple after-treatment system despite the efficiency penalty relative to lean-burn combustion strategies. Exhaust gas recirculation (EGR) has the potential to reduce this efficiency gap at low to moderate loads without the need for complex lean-exhaust aftertreatment systems. However, EGR dilution leads to reduced combustion stability and increased cycle-to-cycle variability. A promising technology that has the potential to achieve reliable operation under diluted conditions is the prechamber ignition (or turbulent jet ignition) which uses chemically active turbulent jets generated from combustion inside a prechamber to initiate, stabilize and accelerate combustion of the mixture inside the main chamber. The present work focusses on developing a RANS-based CFD approach to accurately reproduce in-cylinder phenomena in a stoichiometric NG prechamber-assisted heavy-duty engine without relying on complex combustion models that account for turbulence-chemistry interactions. This is necessary because reactive prechamber jets at high EGR dilution tend to extinguish while emerging into the main chamber, which is followed by a phase of re-ignition — a phenomenon that conventional G-equation or well-stirred reactor combustion models cannot reproduce. With addition of a damping multiplier to the well-stirred reactor model, the predictions are seen to show good agreement with experimental pressure evolution and combustion images acquired from a single cylinder Cummins N-14 optical diesel engine retrofitted with a prechamber ignition system. Model predictions of local heat release in the flame and temperature evolution inside the flame are used to investigate combustion dynamics in the prechamber and the main chamber. It is seen that the well-stirred reactor model with the inclusion of damping is able to reproduce the temporary reduction in heat release within the flame, which can be considered equivalent to quenching of jets, and the subsequent re-ignition of the flame inside the main chamber. The delay between quenching and re-ignition depends on the amount of dilution, as explained by an illustration of flame evolution in a Borghi diagram.

Prechamber ignition↗

Visible-light photocatalytic activity of the metastable Bi{sub 20}TiO{sub 32} synthesized by a high-temperature quenching method

Metastable Bi{sub 20}TiO{sub 32} samples were synthesized by a high-temperature quenching method using alpha-Bi{sub 2}O{sub 3} and anatase TiO{sub 2} as raw materials. The photocatalytic activity of the as-prepared samples was measured with the photodegradation of methyl orange at room temperature under visible light irradiation. The Bi{sub 20}TiO{sub 32} samples exhibited good absorption in the visible light region with a band gap of about 2.38 eV and the band structure of Bi{sub 20}TiO{sub 32} was studied. Photodegradation against methyl orange was much better than alpha-Bi{sub 2}O{sub 3} prepared by the same way. The photocatalytic activity of Bi{sub 20}TiO{sub 32} samples is supposed to be associated with the hybridized Bi 6s and O 2p orbitals. In addition, the dispersive characteristic of Bi 6s orbital in the hybridized valence band facilitates the mobility of the photogenerated carriers and hampers their recombination. - Graphical abstract: Metastable Bi{sub 20}TiO{sub 32} samples were successfully synthesized by a quenching process. Photodegradation against methyl orange showed high visible-light activity and it was supposed to be associated with its corresponding band structure.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Characterization of the microstructure obtained by the quenching and partitioning process in a low-carbon steel

The 'quenching and partitioning' process is a new heat treatment for the development of multiphase steels with improved mechanical properties. In this work, a partial austenitization followed by Q and P paths, at which the partitioning step is effectuated at a temperature equal to the quenching temperature, has been applied to a low-carbon steel. The resulting multiphase microstructures have been investigated by optical microscopy using bright field and differential interference contrast, electron backscatter diffraction, X-ray diffraction and magnetic measurements. This group of techniques has led to a complete identification of the microstructural constituents: ferrite present during the partial austenitization, epitaxial ferrite formed during cooling, martensite and retained austenite. The analysis of the results has shown a significant relevance of the epitaxial ferrite in the retention of austenite, whereas the carbon partitioning from martensite to austenite has played a minor role.

36 MATERIALS SCIENCE↗

Phase transformations in the Zn-Al eutectoid alloy after quenching from the high temperature triclinic beta phase

Ribbons of the Zn-Al eutectoid alloy obtained by melt-spinning, were heat treated at 350 deg. C during 30 min in a free atmosphere furnace, and then quenched in liquid nitrogen. The temperature correspond to {beta} phase zone, which has a triclinic crystalline structure [1, 2]. Some evidence, obtained by X-ray diffraction, show that the structures present in the just quenched material are both close-packed hexagonal ({eta}-phase) and rhombohedral (R-phase). X-ray diffractograms taken in the same ribbons after annealed 500 h at room temperature, show that the R phase its transform to {alpha} and {eta} phases.

36 MATERIALS SCIENCE↗

Measurement of residual stress in quenched 1045 steel by the nanoindentation method

In this paper, the residual stress in quenched AISI 1045 steel was measured by a recently developed nanoindentation technique. Depth control mode was adopted to measure the residual stress. It was found that residual compressive stress was generated in the quenched steel. The material around nanoindents exhibits significant pile-up deformation. A new method was proposed to determine the real contact area for pile-up material on the basis of invariant pile-up morphology of the loaded or unloaded states. The results obtained by the new method were in good agreement with the residual stresses measured by the classical X-ray diffraction (XRD) method. - Research Highlights: {yields} A new method was proposed to measure the real contact area for pile-up materials. {yields} The real contact depth is defined as the sum of h{sub max} and the pile-up height h{sub p}. {yields} The value of residual stress measured by the nanoindentation method was in good agreement with that by the XRD method.

36 MATERIALS SCIENCE↗

Microstructure and partitioning behavior characteristics in low carbon steels treated by hot-rolling direct quenching and dynamical partitioning processes

In this work, a new process and composition design are proposed for “quenching and partitioning” or Q&P treatment. Three low carbon steels were treated by hot-rolling direct quenching and dynamical partitioning processes (DQ&P). The effects of proeutectoid ferrite and carbon concentration on microstructure evolution and mechanical properties were investigated. The present work obtained DQ&P prototype steels with good mechanical properties and established a new notion on compositions for Q&P processing. Microstructures were characterized by means of electro probe microanalyzer (EPMA), scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), transmission electron microscopy (TEM) and X-ray diffraction (XRD), especially the morphology and size of retained austenite. Mechanical properties were measured by uniaxial tensile tests. The results indicated that introducing proeutectoid ferrite can increase the volume fraction of retained austenite and thus improve mechanical properties. TEM observation showed that retained austenite included the film-like inter-lath austenite and blocky austenite located in martensite/ferrite interfaces or surrounded by ferrites. It was interesting that when the carbon concentration is as low as ~ 0.078%, the film-like inter-lath untransformed austenite cannot be stabilized to room temperature and almost all of them transformed into twin martensite. The blocky retained austenite strengthened the interfaces and transformed into twin martensite during the tensile deformation process. The PSEs of specimens all exceeded 20 GPa.%. - Highlights: •This study focused on a new process: Q&P process applying dynamical partitioning. •Ferrite can increase the volume fraction of retained austenite. •The film-like austenite and the blocky austenite were observed. •The low carbon steels treated by new process reached PSEs higher than 20 GPa.%.

36 MATERIALS SCIENCE↗

Relationship between microstructure and mechanical properties of M50 ultra-high strength steel via quenching-partitioning-tempering process

Highlights: • The impact energy of M50 steels treated by QPT process increases by 35–93% than QT. • Cracks distribution inside impact fracture specimens is studied by 3D X-ray tomography. • The work indicates that QPT process can be applied to high-C steel with little Si. Novel quenching-partitioning-tempering (Q-P-T) and traditional quenching-tempering (Q-T) processes are conducted for M50 ultra-high strength steel. An excellent combination of strength and toughness is obtained via the Q-P-T process. The highest impact absorption energy of the Q-P-T specimen increases by 93% compared to the Q-T specimen. However, the yield and ultimate tensile strength of Q-P-T specimens are almost the same as those of Q-T specimens. Microstructure analysis indicates that the maximum fraction of retained austenite in the Q-P-T specimen is 7.5%, which is much higher than that in the Q-T (2.0%) specimen. Meanwhile, more fine cracks appear in the fracture Q-P-T specimen. The precipitation of fine and diffuse ω phase, Fe{sub 3}C and Cr{sub 23}C{sub 6} is observed during the partitioning process. The present work also reveals that the Q-P-T/Q-P process can be applied to high‑carbon steel with little Si or Al.

36 MATERIALS SCIENCE↗

Quantitative investigation into the influence of temperature on carbide and austenite evolution during partitioning of a quenched and partitioned steel

Here, the influence of partitioning temperature on microstructural evolution during quenching and partitioning was investigated in a 0.38C-1.54Mn-1.48Si wt.% steel using Mössbauer spectroscopy and transmission electron microscopy. η-carbide formation occurs in the martensite during the quenching, holding, and partitioning steps. More effective carbon partitioning from martensite to austenite was observed at 450 than 400°C, resulting in lower martensite carbon contents, less carbide formation, and greater retained austenite amounts for short partitioning times. Conversely, greater austenite decomposition occurs at 450°C for longer partitioning times. Lastly, cementite forms during austenite decomposition and in the martensite for longer partitioning times at 450°C.

36 MATERIALS SCIENCE↗

Jet quenching at RHIC. What have we learned?

Partonic energy loss (jet quenching) within the hot and colored medium created in heavy-ion collisions is one of the essential tools to provide quantitative understanding of Quark Gluon Plasma. Measurements of jet quenching via single and di-hadron observables have provided initial estimates of the energy density of the medium. However, these hadron-triggered observables suffer from well-known biases since they fold production cross-sections with the energy loss itself, providing limited information on the initial energy of the propagating jet. Fully reconstructed jets - in terms of energy flow - will allow a complete exploration of fragmentation patterns and will not suffer from geometrical biases, providing deeper understanding of partonic energy loss. We recall the pioneering hadron triggered measurements, summarize their impact and put them in contrast to the recent measurements of fully reconstructed jets in heavy-ions at RHIC.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Effect of collisional quenching on the measurement of ion species mix in neutral beam injectors

A corona model is used in analyzing the Doppler shifted spectroscopy (DSS) data for estimating the ion species mix and beam species fractions in positive ion based neutral beam injectors. In this model the excited neutral atom is assumed to decay solely by a spontaneous radiative process. However, at the beam energies of 20-60 keV/amu, collisional quenching of the excited neutrals affects these estimations when background pressure exceeds 1 mTorr. We present here a modified corona model that takes into account the effects of collisional quenching. We also describe the results of application of the present model to a typical DSS data obtained in the first phase of operation of the SST-1 neutral beam injector.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Influence of quenching rate on the magnetic and martensitic properties of Ni-Fe-Ga melt-spun ribbons

We have fabricated Ni-Fe-Ga {beta} single phase alloy ribbons with Ga content less than 25 at. %. Higher spinning rate of melt-spinning technique can produce {beta} single phase alloys without precipitation of {gamma} particles, whereas lower spinning rate results in the {beta}+{gamma} two phase structure. This higher quenching rate is found to be able to fully suppress the formation of {gamma} phase during fabrication. The martensitic and magnetic transition temperatures of {beta} phase ribbons are both above room temperature, and the ribbon show saturation magnetization as high as 56.5 emu/g at room temperature. These features are attractive for practical applications. The effects of quenching rate on microstructure, martensitic transformation, and magnetic properties are discussed.

36 MATERIALS SCIENCE↗

Off-resonance energy absorption in a linear Paul trap due to mass selective resonant quenching

Linear Paul traps (LPT) are used in many experimental studies such as mass spectrometry, atom-ion collisions, and ion-molecule reactions. Mass selective resonant quenching (MSRQ) is implemented in LPT either to identify a charged particle's mass or to remove unwanted ions from a controlled experimental environment. In the latter case, MSRQ can introduce undesired heating to co-trapped ions of different mass, whose secular motion is off resonance with the quenching ac field, which we call off-resonance energy absorption (OREA). We present simulations and experimental evidence that show that the OREA increases exponentially with the number of ions loaded into the trap and with the amplitude of the off-resonance external ac field.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The impact of nanoperforation on persistent photoconductivity and optical quenching effects in suspended GaN nanomembranes

We report on fabrication of suspended ∼15 nm thick GaN membranes nanoperforated in an ordered fashion using direct writing of negative charges by focused ion beam and subsequent photoelectrochemical etching of GaN epilayers. Both continuous and nanoperforated membranes exhibit persistent photoconductivity (PPC), which can be optically quenched under excitation by 546 nm radiation. Optical quenching of PPC occurs also under relatively intense intrinsic excitation of nanoperforated membranes by 355 nm radiation at T < 100 K. The proposed explanation is based on strong surface localization of charge carriers in nanoperforated membranes and UV-induced reactions occurring at surface states under intense intrinsic excitation.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Defect correlated fluorescent quenching and electron phonon coupling in the spectral transition of Eu{sup 3+} in CaTiO{sub 3} for red emission in display application

This paper reports on the defect correlated self-quenching and spectroscopic investigation of calcium titanate (CaTiO{sub 3}) phosphors. A series of CaTiO{sub 3} phosphors doped with trivalent europium (Eu{sup 3+}) and codoped with potassium (K{sup +}) ions were prepared by the solid state reaction method. The X-ray diffraction results revealed that the obtained powder phosphors consisted out of a single-phase orthorhombic structure and it also indicated that the incorporation of the dopants/co-dopants did not affect the crystal structure. The scanning electron microscopy images revealed the irregular morphology of the prepared phosphors consisting out of μm sized diameter particles. The Eu{sup 3+} doped phosphors illuminated with ultraviolet light showed the characteristic red luminescence corresponding to the {sup 5}D{sub 0}→{sup 7}F{sub J} transitions of Eu{sup 3+}. As a charge compensator, K{sup +} ions were incorporated into the CaTiO{sub 3}:Eu{sup 3+} phosphors, which enhanced the photoluminescence (PL) intensities depending on the doping concentration of K{sup +}. The concentration quenching of Eu{sup 3+} in this host is discussed in the light of ion-ion interaction, electron phonon coupling, and defect to ion energy transfer. The spectral characteristics and the Eu-O ligand behaviour were determined using the Judd-Ofelt theory from the PL spectra instead of the absorption spectra. The CIE (International Commission on Illumination) parameters were calculated using spectral energy distribution functions and McCamy's empirical formula. Photometric characterization indicated the suitability of K{sup +} compensated the CaTiO{sub 3}:Eu{sup 3+} phosphor for pure red emission in light-emitting diode applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Electronic quenching of O({sup 1}D) by Xe: Oscillations in the product angular distribution and their dependence on collision energy

The dynamics of the O({sup 1}D) + Xe electronic quenching reaction was investigated in a crossed beam experiment at four collision energies. Marked large-scale oscillations in the differential cross sections were observed for the inelastic scattering products, O({sup 3}P) and Xe. The shape and relative phases of the oscillatory structure depend strongly on collision energy. Comparison of the experimental results with time-independent scattering calculations shows qualitatively that this behavior is caused by Stueckelberg interferences, for which the quantum phases of the multiple reaction pathways accessible during electronic quenching constructively and destructively interfere.

74 ATOMIC AND MOLECULAR PHYSICS↗

Effect of resistive wall on thermal quench in JET disruptions

In this paper, experimental data, simulations and theory are presented of a JET tokamak thermal quench. The emphasis is on the timescale of the bulk plasma thermal energy loss. The simulations suggest that the thermal energy loss is caused by a resistive wall tearing mode, and experimental data is consistent with this conclusion. The time scale of the thermal quench is the inverse of the mode growth rate.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Thermal quench in ITER locked mode disruptions

Simulations and theory are presented of an ITER locked mode thermal quench(TQ). In present experiments, locked mode disruptions have a long precursor phase,followed by a rapid termination and thermal quench, which can be identified with a resistive wall tearing mode (RWTM). In ITER, the RWTM will be slowed by the highly conductive vacuum vessel. Here, the rapid termination might be absent, and the plasma could remain in the precursor phase. If the edge temperature is in the collisional regime, the TQ would proceed on a long timescale, limited by the RWTM to almost100ms. This is an important self mitigating effect.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗