Results for “Pilot Inputs” — Page 26

NASA NTRS1989

Integrated flight/propulsion control system design based on a centralized approach

An integrated flight/propulsion control system design is presented for the piloted longitudinal landing task with a modern, statically unstable, fighter aircraft. A centralized compensator based on the Linear Quadratic Gaussian/Loop Transfer Recovery methodology is first obtained to satisfy the feedback loop performance and robustness specificiations. This high-order centralized compensator is then partitioned into airframe and engine sub-controllers based on modal controllability/observability for the compensator modes. The order of the sub-controllers is then reduced using internally-balanced realization techniques and the sub-controllers are simplified by neglecting the insignificant feedbacks. These sub-controllers have the advantage that they can be implemented as separate controllers on the airframe and the engine while still retaining the important performance and stability characteristics of the full-order centralized compensator. Command prefilters are then designed for the closed-loop system with the simplified sub-controllers to obtain the desired system response to airframe and engine command inputs, and the overall system performance evaluation results are presented.

Garg, Sanjay↗

NASA NTRS1989

Integrated flight/propulsion control system design based on a centralized approach

An integrated flight/propulsion control system design is presented for the piloted longitudinal landing task with a modern, statically unstable, fighter aircraft. A centralized compensator based on the Linear Quadratic Gaussian/Loop Transfer Recovery methodology is first obtained to satisfy the feedback loop performance and robustness specificiations. This high-order centralized compensator is then partitioned into airframe and engine sub-controllers based on modal controllability/observability for the compensator modes. The order of the sub-controllers is then reduced using internally-balanced realization techniques and the sub-controllers are simplified by neglecting the insignificant feedbacks. These sub-controllers have the advantage that they can be implemented as separate controllers on the airframe and the engine while still retaining the important performance and stability characteristics of the full-order centralized compensator. Command prefilters are then designed for the closed-loop system with the simplified sub-controllers to obtain the desired system response to airframe and engine command inputs, and the overall system performance evaluation results are presented.

Garg, Sanjay↗

NASA NTRS2013

Investigation of Control Inceptor Dynamics and Effect on Human Subject Performance

The control inceptor used in a vehicle simulation is an important part of adequately representing the dynamics of the vehicle. The inceptor characteristics are typically based on a second order spring mass damper system with damping, force gradient, breakout force, and natural frequency parameters. Changing these parameters can have a great effect on pilot control of the vehicle. A quasi transfer of training experiment was performed employing a high fidelity and a low fidelity control inceptor. A disturbance compensatory task was employed which involved a simple horizon line disturbed in roll by a sum of sinusoids presented in an out-the-window display. Vehicle dynamics were modeled as 1/s and 1/s2. The task was to maintain level flight. Twenty subjects were divided between the high and the low fidelity training groups. Each group was trained to a performance asymptote, and then transferred to the high fidelity simulation. RMS tracking error, a PSD analysis, and a workload analysis were performed to quantify the transfer of training effect. Quantitative results of the experiments show that there is no significant difference between the high and low fidelity training groups for 1/s plant dynamics. For 1/s2 plant dynamics there is a greater difference in tracking performance and PSD; and the subjects are less correlated with the input disturbance function

Stanco, Anthony A.↗

NASA NTRS1979

The development of the DAST I remotely piloted research vehicle for flight testing an active flutter suppression control system

The development of the DAST I (drones for aerodynamic and structural testing) remotely piloted research vehicle is described. The DAST I is a highly modified BQM-34E/F Firebee II Supersonic Aerial Target incorporating a swept supercritical wing designed to flutter within the vehicle's flight envelope. The predicted flutter and rigid body characteristics are presented. A description of the analysis and design of an active flutter suppression control system (FSS) designed to increase the flutter boundary of the DAST wing (ARW-1) by a factor of 20% is given. The design and development of the digital remotely augmented primary flight control system and on-board analog backup control system is presented. An evaluation of the near real-time flight flutter testing methods is made by comparing results of five flutter testing techniques on simulated DAST I flutter data. The development of the DAST ARW-1 state variable model used to generate time histories of simulated accelerometer responses is presented. This model uses control surface commands and a Dryden model gust as inputs. The feasibility of the concept of extracting open loop flutter characteristics from closed loop FSS responses was examined. It was shown that open loop characteristics can be determined very well from closed loop subcritical responses.

Grose, D. L.↗

NASA NTRS1984

A real-time, portable, microcomputer-based jet engine simulator

Modern piloted flight simulators require detailed models of many aircraft components, such as the airframe, propulsion system, flight deck controls and instrumentation, as well as motion drive and visual display systems. The amount of computing power necessary to implement these systems can exceed that offered by dedicated mainframe computers. One approach to this problem is through the use of distributed computing, where parts of the simulation are assigned to computing subsystems, such as microcomputers. One such subsystem, such as microcomputers. One such subsystem, a real-time, portable, microcomputer-based jet engine simulator, is described in this paper. The simulator will be used at the NASA Ames Vertical Motion Simulator facility to perform calculations previously done on the facility's mainframe computer. The mainframe will continue to do all other system calculations and will interface to the engine simulator through analog I/0. The engine simulator hardware includes a 16-bit microcomputer and floating-point coprocessor. There is an 8 channel analog input board and an 8 channel analog output board. A model of a small turboshaft engine/control is coded in floating-point FORTRAN. The FORTRAN code and a data monitoring program run under the control of an assembly language real-time executive. The monitoring program allows the user to isplay and/or modify simulator variables on-line through a data terminal. A dual disk drive system is used for mass storage of programs and data. The CP/M-86 operating system provides file management and overall system control. The frame time for the simulator is 30 milliseconds, which includes all analog I/0 operations.

Blech, R. A.↗

NASA NTRS2018

A Markov Decision Process Framework for Optimal Airport Reconfiguration

The airport runway configuration is defined as a combination set of runways for arrivals and departures used at a point during operation of the airport. An optimal configuration of these runways depends on a number of factors, including traffic demand, wind magnitude and direction, other adverse weather conditions, and noise restrictions, among others. Based on the current state of these factors and predictions of traffic demand and weather conditions, runway configuration changes are made and coordinated between tower controller, other air traffic control facilities, pilots, and ground personnel. Reconfigurations can be quite disruptive to airport operations; minimizing their frequency and scheduling them well in advance is essential for mitigating some of the added workload for controllers and pilots. Unfortunately, deciding on an appropriate time to change is challenging for human decision makers. Not only do multiple factors need to be evaluated, but the uncertainty in their forecasts must also be considered. Previous optimization methods, such as mixed linear integer programming, have been proposed. Although these methods can reason over a large set of variables, they do not systematically handle the uncertainty associated with weather movement, traffic demands, and other variables. In this work, we introduce a Markov Decision Process (MDP)-based decision making framework which can reason effectively over the inherent uncertainties and make optimal decisions on if/when to change the airport configuration. In a prototype implementation, we present a single runway with three aircraft and utilize knowledge of the forecasted wind speed and direction to determine whether to keep or change the current runway configuration. Our aim through this work is to present a framework for airport reconfiguration which can be scalable to additional aircraft, multiple runways, and various input parameters. This technique will optimize the airport reconfiguration procedure by providing a proactive approach, optimizing not just at the next optimal opportunity for a reconfiguration based on varying atmospheric and traffic conditions in the terminal airspace, but also anticipating future necessary reconfigurations. This will eliminate the inefficiencies of frequent changes currently associated with runway reconfiguration procedures.

runway reconfiguration↗

NASA NTRS2006

Sensing Super-position: Visual Instrument Sensor Replacement

The coming decade of fast, cheap and miniaturized electronics and sensory devices opens new pathways for the development of sophisticated equipment to overcome limitations of the human senses. This project addresses the technical feasibility of augmenting human vision through Sensing Super-position using a Visual Instrument Sensory Organ Replacement (VISOR). The current implementation of the VISOR device translates visual and other passive or active sensory instruments into sounds, which become relevant when the visual resolution is insufficient for very difficult and particular sensing tasks. A successful Sensing Super-position meets many human and pilot vehicle system requirements. The system can be further developed into cheap, portable, and low power taking into account the limited capabilities of the human user as well as the typical characteristics of his dynamic environment. The system operates in real time, giving the desired information for the particular augmented sensing tasks. The Sensing Super-position device increases the image resolution perception and is obtained via an auditory representation as well as the visual representation. Auditory mapping is performed to distribute an image in time. The three-dimensional spatial brightness and multi-spectral maps of a sensed image are processed using real-time image processing techniques (e.g. histogram normalization) and transformed into a two-dimensional map of an audio signal as a function of frequency and time. This paper details the approach of developing Sensing Super-position systems as a way to augment the human vision system by exploiting the capabilities of the human hearing system as an additional neural input. The human hearing system is capable of learning to process and interpret extremely complicated and rapidly changing auditory patterns. The known capabilities of the human hearing system to learn and understand complicated auditory patterns provided the basic motivation for developing an image-to-sound mapping system.

Maluf, David A.↗

NASA NTRS2007

Sensing Super-Position: Human Sensing Beyond the Visual Spectrum

The coming decade of fast, cheap and miniaturized electronics and sensory devices opens new pathways for the development of sophisticated equipment to overcome limitations of the human senses. This paper addresses the technical feasibility of augmenting human vision through Sensing Super-position by mixing natural Human sensing. The current implementation of the device translates visual and other passive or active sensory instruments into sounds, which become relevant when the visual resolution is insufficient for very difficult and particular sensing tasks. A successful Sensing Super-position meets many human and pilot vehicle system requirements. The system can be further developed into cheap, portable, and low power taking into account the limited capabilities of the human user as well as the typical characteristics of his dynamic environment. The system operates in real time, giving the desired information for the particular augmented sensing tasks. The Sensing Super-position device increases the image resolution perception and is obtained via an auditory representation as well as the visual representation. Auditory mapping is performed to distribute an image in time. The three-dimensional spatial brightness and multi-spectral maps of a sensed image are processed using real-time image processing techniques (e.g. histogram normalization) and transformed into a two-dimensional map of an audio signal as a function of frequency and time. This paper details the approach of developing Sensing Super-position systems as a way to augment the human vision system by exploiting the capabilities of Lie human hearing system as an additional neural input. The human hearing system is capable of learning to process and interpret extremely complicated and rapidly changing auditory patterns. The known capabilities of the human hearing system to learn and understand complicated auditory patterns provided the basic motivation for developing an image-to-sound mapping system. The human brain is superior to most existing computer systems in rapidly extracting relevant information from blurred, noisy, and redundant images. From a theoretical viewpoint, this means that the available bandwidth is not exploited in an optimal way. While image-processing techniques can manipulate, condense and focus the information (e.g., Fourier Transforms), keeping the mapping as direct and simple as possible might also reduce the risk of accidentally filtering out important clues. After all, especially a perfect non-redundant sound representation is prone to loss of relevant information in the non-perfect human hearing system. Also, a complicated non-redundant image-to-sound mapping may well be far more difficult to learn and comprehend than a straightforward mapping, while the mapping system would increase in complexity and cost. This work will demonstrate some basic information processing for optimal information capture for headmounted systems.

Maluf, David A.↗

NASA NTRS2020

Aerosol-Ice Formation Closure Pilot Study (AEROICSTUDY) Field Campaign Report

The aerosol-ice formation closure pilot study (AEROICESTUDY) was a field campaign conducted at the U.S. Department of Energy Atmospheric Radiation Measurement (ARM) user facility at the Southern Great Plains (SGP) observatory from October 7 to 28, 2019. The purpose of this campaign was to test a field observational approach for conducting an aerosol-ice formation closure study. In other words, the goal was to predict the number of ice nucleating particles (INPs) from the measurements of physical and chemical aerosol properties and compare those to measured INP number concentrations. This project was motivated by the fact that the aerosol community has widely conducted aerosol radiative closure, aerosol-cloud condensation nuclei (CCN), and CCN-droplet closure studies to test the physical models and parameterizations that cloud-resolving and climate models rely on to perform reliable simulations of the Earth system and energy budget. However, very few closure studies related to INPs have been conducted, and to our knowledge, none using robust, size-resolved, ambient aerosol composition measurements as model inputs.

aerosol-ice formation↗

NASA NTRS2020

Aerosol-Ice Formation Closure Pilot Study (AEROICESTUDY) Field Campaign Report

The aerosol-ice formation closure pilot study (AEROICESTUDY) was a field campaign conducted at the U.S. Department of Energy Atmospheric Radiation Measurement (ARM) user facility at the Southern Great Plains (SGP) observatory from October 7 to 28, 2019. The purpose of this campaign was to test a field observational approach for conducting an aerosol-ice formation closure study. In other words, the goal was to predict the number of ice nucleating particles (INPs) from the measurements of physical and chemical aerosol properties and compare those to measured INP number concentrations. This project was motivated by the fact that the aerosol community has widely conducted aerosol radiative closure, aerosol-cloud condensation nuclei (CCN), and CCN-droplet closure studies to test the physical models and parameterizations that cloud-resolving and climate models rely on to perform reliable simulations of the Earth system and energy budget. However, very few closure studies related to INPs have been conducted, and to our knowledge, none using robust, size-resolved, ambient aerosol composition measurements as model inputs

AEROICESTUDY↗

NASA NTRS2015

Conflict Alerts for Aircraft Conducting Visual Approaches

It is common for aircraft to conduct visual and instrument final approaches to a single runway or multiple parallel runways. Useful, nonexcessive safety alerts on aircraft conducting visual approaches are helpful to air traffic controllers, though pilots are responsible for separation with the preceding aircraft. A variety of visual approaches to various runway configurations are studied, and a set of safety alert thresholds is proposed. Fast-time simulations with recorded real-world air traffic data of mostly visual approach flights are performed on a prototype tactical separation assurance system for terminal airspace. Alerts are generated -- with both the standard separation thresholds and the proposed safety alert thresholds -- and compared with those from the Conflict Alert (CA) functionality in the Standard Terminal Automation Replacement System (STARS). The results show that the number of Mode-C Intruder alerts generated was reduced 76% as compared to STARS CA. The nuisance alerts generated by assuming visual to be instrument approaches was reduced by 92% when the proposed safety alert thresholds were used and visual approaches were assumed.A set of safety alert thresholds, which allow safety alerts to be provided to the controllers for aircraft conductingvisual approaches to a single runway or multiple parallel runways, has been proposed based on input from SubjectMatter Experts as well as visual approach procedures and common practices. The goal is to maximize the thresholdswithin the guidance of the procedures and common practices and to minimize the number of nuisance alerts and totalnumber of alerts with the support of flight intent information. Tests have been performed using a recently developedprototype tactical separation assurance system for terminal airspace, called Terminal Tactical Separation-AssuredFlight Environment (T-TSAFE). The input was a full day of air traffic data from Dallas/Fort Worth (DFW) TRACONwith most arriving flights conducting visual approaches. The results compare favorably with those of the ConflictAlert (CA) functionality of the Standard Terminal Automation Replacement System (STARS).When fast-time simulation experiment was performed using T-TSAFE with all arriving flights assumed to conductinstrument approaches, the expected large number of separation alerts were observed. When compared with STARSCA, the conflict pairs common to both T-TSAFE and STARS CA was only 21% of the total STARS CA alerts. As aresult, the nuisance-alert rate for STARS CA was estimated to be about 70%, which is comparable to a similar previously estimation of 80% nuisance-alert rate for CARTS (Common Automated Radar Terminal System) CA. The Mode-CIntruder (MCI) alerts were also reduced by 76% as compared to STARS CA.Examination of the common conflict pairs between T-TSAFE and STARS CA shows that they are valid separationconflicts with good alert lead times for T-TSAFE. However, many of them would still be considered nuisance alertsif the aircraft were conducting visual approaches. This was confirmed by another visual approach fast-time simulationT-TSAFE experiment, in which all DFW arriving flights were assumed to be on visual approaches and our proposedsafety alert thresholds were used and tested. The result of the experiment showed that the number of non-MCI alertswas less by 92% as compared to the number when all DFW arrivals were assumed to be conducting instrumentapproaches. The common conflict pairs involving aircraft conducting visual approaches to parallel runways werereduced by 93% as well. Thus, the flight intent information and the safety alert thresholds are effective in reducingnuisance alerts.T-TSAFE can thus provide separation and safety conflict alerts seamlessly in the real-world environment of mixedterminal operations with arriving flights of both visual and instrument approaches. Compared with STARS CA, TTSAFEhas fewer false alerts, larger alert lead time, and larger alert thresholds. While the nuisance alerts are reducedsignificantly with the safety alert thresholds, further work is needed to study if the alert lead time for safety alerts issufficient.

Tang, Huabin↗

NASA NTRS2004

Evaluation of Droplet Splashing Algorithm in LEWICE 3.0

The Icing Branch at NASA Glenn Research has developed a computer program to simulate ice formation on the leading edge of an aircraft wing during flight through cold, moist air. As part of the branch's current research, members have developed software known as LEWICE. This program is capable of predicting the formation of ice under designated weather conditions. The success of LEWICE is an asset to airplane manufacturers, ice protection system manufacturers, and the airline industry. Simulations of ice formation conducted in the tunnel and in flight is costly and time consuming. However, the danger of in-flight icing continues to be a concern for both commercial and military pilots. The LEWICE software is a step towards inexpensive and time efficient prediction of ice collection. In the most recent version of the program, LEWICE contains an algorithm for droplet splashing. Droplet splashing is a natural occurrence that causes accumulation of ice on aircraft surfaces. At impingement water droplets lose a portion of their mass to splashing. With part of each droplet joining the airflow and failing to freeze, early versions of LEWICE without the splashing algorithm over-predicted the collection of ice on the leading edge. The objective of my project was to determine whether the revised version of LEWICE accurately reflected the ice collection data obtained from the Icing Research Tunnel (IRT). The experimental data from the IRT was collected by Mark Potapczuk in January, March and July of 2001 and April and December of 2002. Experimental data points were the result of ice tracings conducted shortly after testing in the tunnel. Run sheets, which included a record of velocity, temperature, liquid water content and droplet diameter, served as the input of the LEWICE computer program. Parameters identical to the tunnel conditions were used to run LEWICE 2.0 and LEWICE 3.0. The results from IRT and versions of LEWICE were compared graphically. After entering the raw experimental data and computer output into a spread sheet, I mapped each ice formation onto a clean airfoil. The LEWICE output provided the data points to graphically depict ice formations developed by the program. weather conditions of runs conducted in January 2001, it was evident that the splashing algorithm of LEWICE 3.0 predicts ice formations more accurately than LEWICE 2.0. Especially at conditions with droplet size between 80 and 160 microns, the splashing algorithm of the new LEWICE version compensated for the loss of droplet mass as a result of splashing. In contrast, LEWICE 2.0 consistently over-predicted the mass of the ice in conditions with droplet size exceeding 80 microns. This evidence confirms that changes made to algorithms of LEWICE 3.0 have increased the accuracy of predicting ice collection.

Homenko, Hilary N.↗

NASA NTRS2003

Measurement and Modeling of Vertically Resolved Aerosol Optical Properties and Radiative Fluxes Over the ARM SGP Site

In order to meet one of its goals - to relate observations of radiative fluxes and radiances to the atmospheric composition - the Department of Energy's Atmospheric Radiation Measurement (ARM) program has pursued measurements and modeling activities that attempt to determine how aerosols impact atmospheric radiative transfer, both directly and indirectly. However, significant discrepancies between aerosol properties measured in situ or remotely remain. One of the objectives of the Aerosol Intensive Operational Period (TOP) conducted by ARM in May 2003 at the ARM Southern Great Plains (SGP) site in north central Oklahoma was to examine and hopefully reduce these differences. The IOP involved airborne measurements from two airplanes over the heavily instrumented SGP site. We give an overview of airborne results obtained aboard the Center for Interdisciplinary Remotely-Piloted Aircraft Studies (CIRPAS) Twin Otter aircraft. The Twin Otter performed 16 research flights over the SGP site. The aircraft carried instrumentation to perform in-situ measurements of aerosol absorption, scattering, extinction and particle size. This included such novel techniques as the photoacoustic and cavity ring-down methods for in-situ absorption (675 nm) and extinction (675 and 1550 nm) and a new multiwavelength, filter-based absorption photometer (467, 530, 660 nm). A newly developed instrument measured cloud condensation nucleus concentration (CCN) concentrations at two supersaturation levels. Aerosol optical depth and extinction (354-2139 nm) were measured with the NASA Ames Airborne Tracking 14-channel sunphotometer. Furthermore, up-and downwelling solar (broadband and spectral) and infrared radiation were measured using seven individual radiometers. Three up-looking radiometers werer mounted on a newly developed stabilized platform, keeping the instruments level up to aircraft pitch and roll angles of approximately 10(exp 0). This resulted in unprecedented continuous vertical profiles of radiative fluxes, which we will compare to modeled fluxes using the aforementioned data as input.

Schmid, B.↗

NASA NTRS2010

Preliminary Design of the Guidance, Navigation, and Control System of the Altair Lunar Lander

Guidance, Navigation, and Control (GN&C) is the measurement and control of spacecraft position, velocity, and attitude in support of mission objectives. This paper provides an overview of a preliminary design of the GN&C system of the Lunar Lander Altair. Key functions performed by the GN&C system in various mission phases will first be described. A set of placeholder GN&C sensors that is needed to support these functions is next described. To meet Crew safety requirements, there must be high degrees of redundancy in the selected sensor configuration. Two sets of thrusters, one on the Ascent Module (AM) and the other on the Descent Module (DM), will be used by the GN&C system. The DM thrusters will be used, among other purposes, to perform course correction burns during the Trans-lunar Coast. The AM thrusters will be used, among other purposes, to perform precise angular and translational controls of the ascent module in order to dock the ascent module with Orion. Navigation is the process of measurement and control of the spacecraft's "state" (both the position and velocity vectors of the spacecraft). Tracking data from the Earth-Based Ground System (tracking antennas) as well as data from onboard optical sensors will be used to estimate the vehicle state. A driving navigation requirement is to land Altair on the Moon with a landing accuracy that is better than 1 km (radial 95%). Preliminary performance of the Altair GN&C design, relative to this and other navigation requirements, will be given. Guidance is the onboard process that uses the estimated state vector, crew inputs, and pre-computed reference trajectories to guide both the rotational and the translational motions of the spacecraft during powered flight phases. Design objectives of reference trajectories for various mission phases vary. For example, the reference trajectory for the descent "approach" phase (the last 3-4 minutes before touchdown) will sacrifice fuel utilization efficiency in order to provide landing site visibility for both the crew and the terrain hazard detection sensor system. One output of Guidance is the steering angle commands sent to the 2 degree-of-freedom (dof) gimbal actuation system of the descent engine. The engine gimbal actuation system is controlled by a Thrust Vector Control algorithm that is designed taking into account the large quantities of sloshing liquids in tanks mounted on Altair. In this early design phase of Altair, the GN&C system is described only briefly in this paper and the emphasis is on the GN&C architecture (that is still evolving). Multiple companion papers will provide details that are related to navigation, optical navigation, guidance, fuel sloshing, rendezvous and docking, machine-pilot interactions, and others. The similarities and differences of GN&C designs for Lunar and Mars landers are briefly compared.

Lee, Allan Y.↗

NASA NTRS1990

A flight expert system for on-board fault monitoring and diagnosis

An architecture for a flight expert system (FLES) to assist pilots in monitoring, diagnosing, and recovering from inflight faults is described. A prototype was implemented and an attempt was made to automate the knowledge acquisition process by employing a learning by being told methodology. The scope of acquired knowledge ranges from domain knowledge, including the information about objects and their relationships, to the procedural knowledge associated with the functionality of the mechanisms. AKAS (automatic knowledge acquisition system) is the constructed prototype for demonstration proof of concept, in which the expert directly interfaces with the knowledge acquisition system to ultimately construct the knowledge base for the particular application. The expert talks directly to the system using a natural language restricted only by the extent of the definitions in an analyzer dictionary, i.e., the interface understands a subset of concepts related to a given domain. In this case, the domain is the electrical system of the Boeing 737. Efforts were made to define and employ heuristics as well as algorithmic rules to conceptualize data produced by normal and faulty jet engine behavior examples. These rules were employed in developing the machine learning system (MLS). The input to MLS is examples which contain data of normal and faulty engine behavior and which are obtained from an engine simulation program. MLS first transforms the data into discrete selectors. Partial descriptions formed by those selectors are then generalized or specialized to generate concept descriptions about faults. The concepts are represented in the form of characteristic and discriminant descriptions, which are stored in the knowledge base and are employed to diagnose faults. MLS was successfully tested on jet engine examples.

Ali, Moonis↗

NASA NTRS2009

Watershed and Hydrodynamic Modeling for Evaluating the Impact of Land Use Change on Submerged Aquatic Vegetation and Seagrasses in Mobile Bay

There is a continued need to understand how human activities along the northern Gulf of Mexico coast are impacting the natural ecosystems. The gulf coast is experiencing rapid population growth and associated land cover/land use change. Mobile Bay, AL is a designated pilot region of the Gulf of Mexico Alliance (GOMA) and is the focus area of many current NASA and NOAA studies, for example. This is a critical region, both ecologically and economically to the entire United States because it has the fourth largest freshwater inflow in the continental USA, is a vital nursery habitat for commercially and recreational important fisheries, and houses a working waterfront and port that is expanding. Watershed and hydrodynamic modeling has been performed for Mobile Bay to evaluate the impact of land use change in Mobile and Baldwin counties on the aquatic ecosystem. Watershed modeling using the Loading Simulation Package in C++ (LSPC) was performed for all watersheds contiguous to Mobile Bay for land use Scenarios in 1948, 1992, 2001, and 2030. The Prescott Spatial Growth Model was used to project the 2030 land use scenario based on observed trends. All land use scenarios were developed to a common land classification system developed by merging the 1992 and 2001 National Land Cover Data (NLCD). The LSPC model output provides changes in flow, temperature, sediments and general water quality for 22 discharge points into the Bay. These results were inputted in the Environmental Fluid Dynamics Computer Code (EFDC) hydrodynamic model to generate data on changes in temperature, salinity, and sediment concentrations on a grid with four vertical profiles throughout the Bay s aquatic ecosystems. The models were calibrated using in-situ data collected at sampling stations in and around Mobile bay. This phase of the project has focused on sediment modeling because of its significant influence on light attenuation which is a critical factor in the health of submerged aquatic vegetation. The impact of land use change on sediment concentrations was evaluated by analyzing the LSPC and EFDC sediment simulations for the four land use scenarios. Such analysis was also performed for storm and non-storm periods. In- situ data of total suspended sediments (TSS) and light attenuation were used to develop a regression model to estimate light attenuation from TSS. This regression model was used to derive marine light attenuation estimates throughout Mobile bay using the EFDC TSS outputs. The changes in sediment concentrations and associated impact on light attenuation in the aquatic ecosystem were used to perform an ecological analysis to evaluate the impact on seagreasses and Submerged Aquatic Vegetation (SAV) habitat. This is the key product benefiting the Mobile Bay coastal environmental managers that integrates the influences of sediments due to land use driven flow changes with the restoration potential of SAVs.

Estes, Maurice G.↗

NASA NTRS2014

NASA's Asteroid Redirect Mission: The Boulder Capture Option

NASA is examining two options for the Asteroid Redirect Mission (ARM), which will return asteroid material to a Lunar Distant Retrograde Orbit (LDRO) using a robotic solar-electric-propulsion spacecraft, called the Asteroid Redirect Vehicle (ARV). Once the ARV places the asteroid material into the LDRO, a piloted mission will rendezvous and dock with the ARV. After docking, astronauts will conduct two extravehicular activities (EVAs) to inspect and sample the asteroid material before returning to Earth. One option involves capturing an entire small (approximately 4-10 m diameter) near-Earth asteroid (NEA) inside a large inflatable bag. However, NASA is examining another option that entails retrieving a boulder (approximately 1-5 m) via robotic manipulators from the surface of a larger (approximately 100+ m) pre-characterized NEA. This option can leverage robotic mission data to help ensure success by targeting previously (or soon to be) well-characterized NEAs. For example, the data from the Hayabusa mission has been utilized to develop detailed mission designs that assess options and risks associated with proximity and surface operations. Hayabusa's target NEA, Itokawa, has been identified as a valid target and is known to possess hundreds of appropriately sized boulders on its surface. Further robotic characterization of additional NEAs (e.g., Bennu and 1999 JU3) by NASA's OSIRIS REx and JAXA's Hayabusa 2 missions is planned to begin in 2018. The boulder option is an extremely large sample‐return mission with the prospect of bringing back many tons of well‐characterized asteroid material to the Earth‐Moon system. The candidate boulder from the target NEA can be selected based on inputs from the world‐wide science community, ensuring that the most scientifically interesting boulder be returned for subsequent sampling. This boulder option for NASA's ARM can leverage knowledge of previously characterized NEAs from prior robotic missions, which provides more certainty of the target NEA's physical characteristics and reduces mission risk. This increases the return on investment for NASA's future activities with respect to science, human exploration, resource utilization, and planetary defense

Abell, Paul A.↗

NASA NTRS2009

Joint Carrier-Phase Synchronization and LDPC Decoding

A method has been proposed to increase the degree of synchronization of a radio receiver with the phase of a suppressed carrier signal modulated with a binary- phase-shift-keying (BPSK) or quaternary- phase-shift-keying (QPSK) signal representing a low-density parity-check (LDPC) code. This method is an extended version of the method described in Using LDPC Code Constraints to Aid Recovery of Symbol Timing (NPO-43112), NASA Tech Briefs, Vol. 32, No. 10 (October 2008), page 54. Both methods and the receiver architectures in which they would be implemented belong to a class of timing- recovery methods and corresponding receiver architectures characterized as pilotless in that they do not require transmission and reception of pilot signals. The proposed method calls for the use of what is known in the art as soft decision feedback to remove the modulation from a replica of the incoming signal prior to feeding this replica to a phase-locked loop (PLL) or other carrier-tracking stage in the receiver. Soft decision feedback refers to suitably processed versions of intermediate results of iterative computations involved in the LDPC decoding process. Unlike a related prior method in which hard decision feedback (the final sequence of decoded symbols) is used to remove the modulation, the proposed method does not require estimation of the decoder error probability. In a basic digital implementation of the proposed method, the incoming signal (having carrier phase theta theta (sub c) plus noise would first be converted to inphase (I) and quadrature (Q) baseband signals by mixing it with I and Q signals at the carrier frequency [wc/(2 pi)] generated by a local oscillator. The resulting demodulated signals would be processed through one-symbol-period integrate and- dump filters, the outputs of which would be sampled and held, then multiplied by a soft-decision version of the baseband modulated signal. The resulting I and Q products consist of terms proportional to the cosine and sine of the carrier phase cc as well as correlated noise components. These products would be fed as inputs to a digital PLL that would include a number-controlled oscillator (NCO), which provides an estimate of the carrier phase, theta(sub c).

Simon, Marvin↗