Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PWR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

Impact of B{sub 4}C on the stratification of molten steel and BWR-type core material under IVR conditions

As part of the validation of the In-Vessel Melt Retention (IVR) strategy for its KERENA BWR, AREVA NP has performed a quantitative assessment of the potential impact of thermochemical phenomena. This was motivated by the fact that several of these phenomena, namely the formation of a dense metallic phase, have the potential to lead to a strong increase in local heat fluxes, with the risk of early IVR failure. In this context, experiments performed in the MASCA project with PWR-type corium melts were repeated using a typical BWR core melt: characterized by a lower U/Zr-ratio and higher contents of Zr, steel, and boron carbide (B{sub 4}C). Applying an improved 'cold crucible' induction heating technique, two series of test were performed, first without B{sub 4}C and then with a B{sub 4}C content of about 1.4 wt%. These two values bound the uncertainty with respect to the incorporation of B{sub 4}C into the molten pool. The target of the tests was to localize the point of equal densities between the dense metallic phase (Fe, U, Zr and O) and the residual oxidic phase in thermo-chemical equilibrium. An interesting result of these experiments was that, different from earlier MASCA tests with PWR-type corium that showed an only insignificant impact of B{sub 4}C on metal density, the new experiments reveal a strong corresponding effect, which can over-compensates the density increase caused by U-migration into the metallic melt. This deviating result is attributed, first, to the higher Zr-fraction in the BWR-type core melt, and second, to the higher content of B{sub 4}C in the BWR-type melt in comparison to the MASCA tests (B{sub 4}C-content <0.5 wt%). Based on the obtained results it is predicted that - under certain conditions -B{sub 4}C can completely prevent the formation of a dense metallic phase, independent of the amount of molten steel in the melt. The paper gives an overview of the performed experiments and their main results and provides theoretical models to explaining the observed strong reduction in metallic phase density in presence of B{sub 4}C Their predictions are then compared to the experimental data. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Automatic treatment of the variance estimation bias in TRIPOLI-4 criticality calculations

The central limit (CLT) theorem States conditions under which the mean of a sufficiently large number of independent random variables, each with finite mean and variance, will be approximately normally distributed. The use of Monte Carlo transport codes, such as Tripoli4, relies on those conditions. While these are verified in protection applications (the cycles provide independent measurements of fluxes and related quantities), the hypothesis of independent estimates/cycles is broken in criticality mode. Indeed the power iteration technique used in this mode couples a generation to its progeny. Often, after what is called 'source convergence' this coupling almost disappears (the solution is closed to equilibrium) but for loosely coupled systems, such as for PWR or large nuclear cores, the equilibrium is never found, or at least may take time to reach, and the variance estimation such as allowed by the CLT is under-evaluated. In this paper we first propose, by the mean of two different methods, to evaluate the typical correlation length, as measured in cycles number, and then use this information to diagnose correlation problems and to provide an improved variance estimation. Those two methods are based on Fourier spectral decomposition and on the lag k autocorrelation calculation. A theoretical modeling of the autocorrelation function, based on Gauss-Markov stochastic processes, will also be presented. Tests will be performed with Tripoli4 on a PWR pin cell. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Application of fully ceramic microencapsulated fuels in light water reactors

This study performs a preliminary evaluation of the feasibility of incorporation of Fully Ceramic Microencapsulated (FCM) fuels in light water reactors (LWRs). In particular, pin cell, lattice, and full core analyses are carried out on FCM fuel in a pressurized water reactor (PWR). Using uranium-based fuel and Pu/Np-based fuel in TRistructural isotropic (TRISO) particle form, each fuel design was examined using the SCALE 6.1 analytical suite. In regards to the uranium-based fuel, pin cell calculations were used to determine which fuel material performed best when implemented in the fuel kernel as well as the size of the kernel and surrounding particle layers. The higher fissile material density of uranium mononitride (UN) proved to be favorable, while the parametric studies showed that the FCM particle fuel design with 19.75% enrichment would need roughly 12% additional fissile material in comparison to that of a standard UO{sub 2} rod in order to match the lifetime of an 18-month PWR cycle. As part of the fuel assembly design evaluations, fresh feed lattices were modeled to analyze the within-assembly pin power peaking. Also, a 'color-set' array of assemblies was constructed to evaluate power peaking and power sharing between a once-burned and a fresh feed assembly. In regards to the Pu/Np-based fuel, lattice calculations were performed to determine an optimal lattice design based on reactivity behavior, pin power peaking, and isotopic content. After obtaining a satisfactory lattice design, the feasibility of core designs fully loaded with Pu/Np FCM lattices was demonstrated using the NESTLE three-dimensional core simulator. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Comparison of SERPENT and CASMO-5M for pressurized water reactors models

The objective of this work is to perform a preliminary assessment of the capability of SERPENT to generate cross sections for a PWR Beginning-of-Life (BOL) isothermal mini-core by comparing a SERPENT/PARCS solution with the results obtained using a CASMO-5M/PARCS approach. The PARCS code is used instead of the usual SIMULATE-3 to analyze the Swiss Reactors, because interfaces with PARCS already exist to obtain neutronic data from SERPENT. For the PWR configurations, the differences between CASMO-5M and SERPENT solutions are within 200 pcm at the assembly level and thus rather small when considering the deterministic transport method (energy/angular/space discretization) in CASMO-5M versus the stochastic treatment of SERPENT, the statistical uncertainties in the Monte-Carlo approach as well as the eventual differences in nuclear data used by both codes. At the 2D mini-core level, no major difference is observed when comparing PARCS run with CASMO-5M versus SERPENT cross sections. For the generation of kinetic parameters, non trivial differences are observed due both to the methods and the data used. For the relatively limited number of configurations considered, it is hard to make any definitive statement on the benefits of using Monte Carlo codes in terms of nuclear data generation. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Impact of Storage Time on the Needed Capture Efficiency for Volatile Radionuclides - 13369

During the processing of used nuclear fuel (UNF), volatile radionuclides will be discharged from the facility stack if no recovery processes are in place to limit their release. The volatile radionuclides of concern are {sup 3}H, {sup 14}C, {sup 85}Kr, and {sup 129}I. There are three key regulations that address the release of these radionuclides to the environment- 40 CFR 61, 40 CFR 190, and 10 CFR 20. These regulations apply to the total radionuclide release and establish dose limits for the maximum exposed individual (MEI) in the public both in terms of whole body dose and dose to specific organs such as the thyroid. Each radionuclide released to the environment contributes to the total dose to some degree. In this paper we attempt to evaluate the efficiency requirements for the capture processes to limit the doses to the MEI to regulatory levels. Since the total amount of each volatile radionuclide present in the UNF changes with the age of the fuel, the respective capture requirements also change with time. Specifically, we are interested in the impact of the decreasing contribution of {sup 3}H and {sup 85}Kr, which have relatively short half-lives, 12.32 y and 10.76 y, respectively, with the increasing age of the fuel (i.e., time between when the UNF is removed from the reactor and the time it is processed) on the capture requirements. In this paper we examine the capture requirements for these four radionuclides for three fuel types (pressurized water reactor [PWR] with uranium oxide fuel [UOX], PWR with mixed oxide fuel [MOX], and an advanced high temperature gas-cooled reactor [AHTGR]), several burnup values, and time out of reactor extending to 200 y. We calculate doses to the MEI with the EPA code CAP-88 and look at two dose contribution cases. In the first case, we assume that the total allowable dose is attributed to only the four volatile radionuclides. This establishes the lowest capture efficiency value possible. Since this is unrealistic, because it assumes zero dose contribution from all other radionuclides, we also examine a second case, where only 10% of the allowable dose is assigned to the four volatile radionuclides. We calculate the required decontamination factors (DFs) for both of these cases for the three fuel types, multiple fuel burnups, and fuel ages and determine whether or not the dose to the whole body or to the thyroid that drives the capture requirements would require additional effluent controls for the shorter half-life volatile radionuclides based on dose considerations. This analysis indicates that the principal isotopes of concern are generally {sup 3}H and {sup 129}I, the latter requiring the highest DFs. The maximum DF value for {sup 129}I is 8000 for the evaluated cases and assumptions used. ∼60 for fresh fuels. The DF for {sup 14}C could be as high as 30 for certain fuels. These values are based on just meeting the regulatory limits, and additional engineering margins (perhaps 3x to 10x or higher) should be applied to provide a safety factor for compliance. However, by assuming less conservative dose allocations, taller stacks, different radionuclide speciation, fuel aging, and other reprocessing facility design and location parameters, the DF requirements could be significantly reduced. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

One pass core design of a super fast reactor

One pass core design for Supercritical-pressure light water-cooled fast reactor (Super FR) is proposed. The whole core is cooled with upward flow in one through flow pattern like PWR. Compared with the previous two pass core design; this new flow pattern can significantly simplify the core concept. Upper core structure, coolant flow scheme as well as refueling procedure are as simple as in PWR. In one pass core design, supercritical-pressure water is at approximately 25.0 MPa and enters the core at 280 C. degrees and is heated up in one through flow pattern upwardly to the average outlet temperature of 500 C. degrees. Great density change in vertical direction can cause significant axial power offset during the cycle. Meanwhile, Pu accumulated in the UO{sub 2} fuel blanket assemblies also introduces great power increase during cycle, which requires large amount of flow for heat removal and makes the outlet temperature of blanket low at the beginning of equilibrium cycle (BOEC). To deal with these issues, some MOX fuel is applied in the bottom region of the blanket assembly. This can help to mitigate the power change in blanket due to Pu accumulation and to increase the outlet temperature of the blanket during cycle. Neutron transport and thermohydraulics coupled calculation shows that this design can satisfy the requirement in the Super FR principle for both 500 C. degrees outlet temperature and negative coolant void reactivity. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Radioactive Spent Ion-Exchange Resins Conditioning by the Hot Supercompaction Process at Tihange NPP - Early Experience - 12200

Spent ion-exchange resins are considered to be problematic waste that, in many cases, requires special approaches and precautions during their conditioning to meet the acceptance criteria for disposal. In Belgium, for economical reasons, the Volume Reduction Factor is a key criterion. After Tractebel Engineering performed a technical and economical comparison of the industrially available systems, Tihange NPP decided to install a spent ion-exchange resins hot supercompaction unit with Tractebel Engineering in the role of architect-engineer. The treatment and conditioning unit processes the spent ion-exchange resins through the following steps: dewatering of the resins, drying the resins under deep vacuum, discharging the dried resins into compactable drums, super-compacting the drums to generate pellets, grouting the pellets into standard 400 litres waste drums (overpacks) licensed for final disposal in the near-surface repository in Belgium. Several developments were required to adapt the reference process and equipment to PWR spent ion-exchange bead resins and Belgian radioactive waste acceptance criteria. In order to avoid cracks on the compacted drum, and external surface contamination from resin leaks, some improvements were achieved to minimize spring-back as well as the risk of cracking the drum wall. Placing the compactable drum inside a second, slightly larger drum, guarantees clean and reproducible pellets. Currently the commissioning phase is on-going. Numerous process validation tests have been completed. An acceptance file was transmitted to the Belgian Waste Management Authority recently. This will be followed by demonstration tests necessary to obtain their final acceptance of the installation. More than 3 800 drums of mixed powdered and bead resins have been processed by the reference Hot Compaction process, achieving a Volume Reduction Factor (VRF) of 2.5. The equipment has been proven to be a reliable technology with low operation and maintenance costs. Tractebel Engineering has managed the construction of a new application of this process in Belgium at Tihange NPP. Several developments were required to adapt the reference process and equipment to PWR spent ion-exchange bead resins and Belgian radioactive waste acceptance criteria. The chosen method of conditioning (draining, drying and compaction of the spent resins followed by grouting of the pellets in a 400 litres drum) immobilizes the spent resins under the form of a solid, compact, stable, and non dispersible block free of interstitial water. The various series of inactive tests which were conducted at Tihange NPP, helped among others to determine the best design of the compactable drum and lid and to set the value of critical parameters such as vapour temperature at the end of drying, speed, force and duration of compaction. In an environment of very limited space for interim storage and in the absence of an operational final repository site, or in the case of high final disposal costs, the process exhibits the following key advantages: - Achieving a Volume Reduction Factor (VRF) close to 1 (overpack included) for the interim storage instead of increased volumes observed with other currently available processes; - Achieving a water free end product; - Creating a flexible waste product for interim storage (pellet), which can be retrieved and routed into alternative types of package later, if not initially grouted; - Using well proven standard technologies like drying and compaction; - Flexible use of the system components for the supercompaction of other operational solid waste streams when not conducting resins conditioning campaigns. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Behavior of high-burnup advanced LWR fuels under accident conditions

Advanced fuels for LWRs which consist of cladding materials with high corrosion resistance and pellets with lower fission gas release have been developed by utilities and fuel vendors to improve the fuel performance even in the high burnup region and also raise the safety level of current nuclear power plants to a higher one. In order to evaluate the adequacy of present safety criteria and safety margins in terms of such advanced fuels and provide a database for future regulation of them, JAEA has started a new extensive research program called ALPS-II program. The ALPS-II program is primarily composed of tests simulating a RIA (Reactivity Initiated Accident) (VA-5 and -6 tests) and a LOCA (Loss Of Coolant Accident) on high burnup advanced fuels irradiated in commercial PWR or BWRs and started in JFY 2008. Recently, post-test examinations on the fuel rods after the pulse irradiation tests of VA-5 and -6 were performed and the relationship between the failure limits of the high burnup advanced fuels with M-MDA{sup TM} cladding and the morphology of the hydrides precipitated in the cladding during normal operation was investigated. The difference in the crack surface morphology was observed between tests VA-5 and-6, which seemed to reflect the difference in the direction along which hydrides precipitate in the cladding. This indicates that the hydride precipitated in the cladding, which is considered to be dependent on the final heat treatment at fabrication, affects the fuel enthalpy at failure. In terms of the simulated LOCA test, integral thermal shock tests and high temperature oxidation tests have been conducted on high burnup PWR and BWR fuel cladding with advanced materials, and their fracture limits, high temperature oxidation rates, etc. were investigated. In the recent integral thermal shock tests for high burnup BWR cladding, namely Zry-2/LK3 material, no fractures were observed. In terms of the oxidation rate tests, the oxidation rate of irradiated M5{sup TM} was similar to those of unirradiated Zry-4 and M5{sup TM} and lower than the values estimated by the Baker-Just equation. From the results of these tests, it was found that in terms of these materials the fracture boundaries do not decrease and the oxidation does not significantly accelerate in the burnup level examined.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

U.S. implementation of Q12{sup TM} zirconium alloy for improved stability of structural components

AREVA NP undertook the Q12{sup TM} research and development program to optimize the contribution to fuel assembly dimensional stability of structural components fabricated from ultra-low tin Zr-1Nb-Sn-Fe quaternary alloys. Because Q12{sup TM} is an evolutionary development of the current M5 alloy metallurgy, it benefits from the extensive industrial experience already gained with the latter. The Q12{sup TM} alloy is processed in the same way as M5, with slight increases in tin (Sn) and iron (Fe) contents. For structural components, these chemistry modifications provide higher irradiation creep strength and improved corrosion performance over Zircaloy-4. Fuel assemblies with quaternary alloy guide tubes are thus expected to increase robustness with respect to fuel assembly bow, improve growth characteristics, and maintain high burnup capability. The basic material properties have been determined through various in-core and out-of-core test programs. Components made from Q12{sup TM} have undergone irradiation in lead assemblies and in batch fuel for 13 Pressurized Water Reactor (PWR) units worldwide. Fuel with Q12{sup TM} guide tubes and grids has achieved a fuel assembly average burnup of 60 GWd/tU. Post irradiation examinations of these components have demonstrated that Q12{sup TM} performs in a stable, predictable manner. AREVA NP has submitted a topical report (TR) for Q12{sup TM} as a structural material to the United States Nuclear Regulatory Commission (US-NRC). This TR outlines the material behavior and performance of Q12{sup TM} for both guide tubes and grids. Once approved, implementation of Q12{sup TM} material throughout US PWR fuel designs will enhance dimensional stability of structural components. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Performance of U{sub 3}Si{sub 2} fuel in a reactivity insertion accident

In this study we examined the performance of the U{sub 3}Si{sub 2} fuel cladded with Zircaloy (Zr) in a reactivity insertion accident (RIA) in a PWR core. The power excursion as a result of a $1 reactivity insertion was calculated by a TRACE PWR plant model using point-kinetics, for alternative cores with UO{sub 2} and U{sub 3}Si{sub 2} fuel assemblies. The point-kinetics parameters (feedback coefficients, prompt-neutron lifetime and group constants for six delayed neutron groups) were obtained from beginning-of-cycle equilibrium full core calculations with PARCS. In the PARCS core calculations, the few-group parameters were developed utilizing the TRITON/NEWT tools in the SCALE package. In order to assess the fuel response in finer detail (e.g. the maximum fuel temperature), the power shape and thermal boundary conditions from the TRACE/PARCS calculations were used to drive a BISON model of a fuel pin with U{sub 3}Si{sub 2} and UO{sub 2} respectively. For a $1 reactivity transient, both TRACE and BISON predicted a higher maximum fuel temperature for the UO{sub 2} fuel than the U{sub 3}Si{sub 2} fuel. Furthermore, BISON is noted to calculate a narrower gap and a higher gap heat transfer coefficient than TRACE. This resulted in BISON predicting consistently lower fuel temperatures than TRACE. This study also provided a systematic comparison between TRACE and BISON using consistent transient boundary conditions. The TRACE analysis of the RIA only reflected the core-wide response in power. A refinement to the analysis would be to predict the local peaking in a three-dimensional core as a result of control rod ejection and at hot zero power conditions. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

TREAT neutronics analysis and design support, Part II: Multi-SERTTA-CAL

Experiment vehicle design is necessary in preparation for Transient Reactor Test (TREAT) facility restart and the resumption of transient testing to support Accident Tolerant Fuel (ATF) characterization and other future fuels testing requirements. Currently the most mature vehicle design is the Multi-SERTTA (Static Environments Rodlet Transient Test Apparatuses), which can accommodate up to four concurrent rodlet-sized specimens under separate environmental conditions. Robust test vehicle design requires neutronics analyses to support design development, optimization of the power coupling factor (PCF) to efficiently maximize energy generation in the test fuel rodlets, and experiment safety analyses. An integral aspect of prior TREAT transient testing was the incorporation of calibration experiments to experimentally evaluate and validate test conditions in preparation of the actual fuel testing. The calibration experiment package established the test parameter conditions to support fine-tuning of the computational models to deliver the required energy deposition to the fuel samples. The calibration vehicle was designed to be as near neutronically equivalent to the experiment vehicle as possible to minimize errors between the calibration and final tests. The Multi-SERTTA-CAL vehicle was designed to serve as the calibration vehicle supporting Multi-SERTTA experimentation. Models of the Multi-SERTTA-CAL vehicle containing typical PWR-fuel rodlets were prepared and neutronics calculations were performed using MCNP6.1 with ENDF/B-VII.1 nuclear data libraries; these results were then compared against those performed for Multi-SERTTA to determine the similarity and possible design modification necessary prior to construction of these experiment vehicles. The estimated reactivity insertion worth into the TREAT core is very similar between the two vehicle designs, with the primary physical difference being a hollow Inconel tube running down the length of the calibration vehicle. Calculations of PCF indicate that on average there is a reduction of approximately 6 % for PWR fuel rodlets irradiated under both wet and dry conditions. Changes to the primary or secondary vessel structure in the calibration vehicle can be performed to offset this discrepancy and maintain neutronic equivalency. Current possible modifications to the calibration vehicle include reduction of the primary vessel wall thickness, swapping Zircaloy-4 for stainless steel 316 in the secondary containment, or slight modification to the temperature and pressure of the water environment within the primary vessel. Removal of some of the instrumentation within the calibration vehicle can also serve to slightly increase the PCF. Future efforts include further modification and optimization of the Multi-SERTTA and Multi-SERTTA-CAL designs in preparation of actual TREAT transient testing. Experimental results from both test vehicles will be compared against calculational results and methods to provide validation and support additional neutronics analyses. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Transient performance of accident tolerant fuel in design basis accidents

A set of transient analysis has been performed to assess the performance of candidate accident tolerant fuel (ATF) against reference UO{sub 2} fuel with Zircaloy cladding under design basis accident (DBA) conditions. This study examined two ATF options, U{sub 3}Si{sub 2} fuel with SiC cladding and UO{sub 2} fuel with APMT cladding. The accident analyses were conducted using the system code TRACE for a three-loop PWR plant. PARCS standalone full-core calculations were done for each fuel/cladding combination to provide inputs to the TRACE point-kinetics model. The design basis accidents analyzed were a reactivity insertion accident (RIA) and a large break loss-of-coolant accident (LBLOCA). The RIA was simulated by the insertion of a reactivity ramp of $1 (one dollar) in 0.1 s at hot full power (HFP) condition. The LBLOCA was a simulation of a double-ended pipe break in one of the cold legs of the primary loops. Differences in thermal responses of the fuel and the cladding are attributed to their thermal properties. The U{sub 3}Si{sub 2} fuel with its lower volumetric heat capacity and higher thermal conductivity (i.e. higher thermal diffusivity) generally results in a lower fuel temperature than the UO{sub 2} fuel and a correspondingly faster thermal response. Additional calculations for the U{sub 3}Si{sub 2} fuel shows that in a RIA the cladding material, SiC versus Zr, has little impact on the maximum fuel centerline temperature and the PCT (peak cladding temperature). An increase in the hot rod power factor is shown to raise the centerline fuel temperature in a RIA but has little impact on the PCT. The analysis results show that for a relatively fast decay heat driven transient, such as the LBLOCA, the thermal-hydraulics and fuel/cladding thermal properties dictate the overall response more so than the reactivity feedback. The results show that the PCTs in a LBLOCA are similar for all fuel/cladding combinations considered in this study. The LBLOCA analysis also notes the impact of the asymmetry in the system response. The fuel rods in the sector of the core connected to the hot leg of the broken loop (Sector 1 in the PWR model) is shown to have a much lower PCT than fuel rods in the other five sectors of the core. Results of this study indicate that for the two DBAs considered (RIA and LBLOCA) the transient behavior and the resulting peak cladding temperature of the two ATF options (U{sub 3}Si{sub 2} fuel with SiC cladding and UO{sub 2} fuel with APMT cladding) are similar to the standard light-water reactor fuel (UO{sub 2} fuel with Zircaloy cladding). (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

TREAT neutronics analysis and design support, Part I: Multi-SERTTA

Experiment vehicle design is necessary in preparation for Transient Reactor Test (TREAT) facility restart and the resumption of transient testing to support Accident Tolerant Fuel (ATF) characterization and other future fuels testing requirements. Currently the most mature vehicle design is the Multi-SERTTA (Static Environments Rodlet Transient Test Apparatuses), which can accommodate up to four concurrent rodlet-sized specimens under separate environmental conditions. Robust test vehicle design requires neutronics analyses to support design development, optimization of the power coupling factor (PCF) to efficiently maximize energy generation in the test fuel rodlets, and experiment safety analyses. Calculations were performed to support analysis of a near-final design of the Multi-SERTTA vehicle, the design process for future TREAT test vehicles, and establish analytical practices for upcoming transient test experiments. Models of the Multi-SERTTA vehicle containing typical PWR-fuel rodlets were prepared and neutronics calculations were performed using MCNP6.1 with ENDF/B-VII.1 nuclear data libraries. Calculation of the PCF for reference conditions of a PWR fuel rodlet in clean water at operational temperature and pressure provided results between 1.10 and 1.73 W/g-MW depending on the location of the four Multi-SERTTA units with the stack. Basic changes to the Multi-SERTTA secondary vessel containment and support have minimal impact on PCF; using materials with less neutron absorption can improve expected PCF values, especially in the primary containment. An optimized balance is needed between structural integrity, experiment safety, and energy deposition in the experiment. Type of medium and environmental conditions within the primary vessel surrounding the fuel rodlet can also have a significant impact on resultant PCF values. The estimated reactivity insertion worth into the TREAT core is impacted more by the primary and secondary Multi-SERTTA vehicle structure with the experiment content and contained environment having a near negligible impact on overall system reactivity. Additional calculations were performed to evaluate the peak-to-average assembly powers throughout the TREAT core, as well as the nuclear heat generation for the various structural components of the Multi-SERTTA assembly. Future efforts include the evaluation of flux collars to shape the PCF for individual Multi-SERTTA units during an experiment such as to achieve uniformity in test unit environmental conditions impacted by the non-uniform axial flux/power profile of TREAT. Upon resumption of transient testing, experimental results from both the Multi-SERTTA and Multi-SERTTA-CAL will be compared against calculational results and methods for further optimization and design strategies. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Meeting the industry challenge to achieve leak free performance

Deployment of highly reliability fuel products is one of AREVA NP's overarching philosophies. Any fuel defect brings appreciable burden to utility and fuel vendors alike. AREVA NP's achievements in leaker free performance are direct results of rigorous investigations and development of innovative products and solutions to address longstanding industry fuel reliability concerns. An illustrative example of this commitment can be found in the AREVA NP's BWR fuel product line. PCI had been a leading failure mechanism in BWR fuel supplied in the United States. In response, AREVA NP implemented improved pellet designs, tighter manufacturing standards, and industry-leading power maneuvering methodologies that have eliminated PCI failures altogether. Likewise, failures resulting from small debris forms in the primary system have been a leading failure mechanism in the BWR fuel. The implementation of advanced debris filters such as the Improved FUELGUARD and 3. Generation FUELGUARD have virtually eliminated debris-related failures. AREVA NP's commitment to fuel reliability is not limited to the BWR fuel products. Grid-to-Rod Fretting (GTRF) has long been a dominant PWR failure mechanism in the industry and results from challenging cross-flows within specific reactor designs that excite and ultimately cause the fuel rod to fret against the spacer contacts to the point of failure. In 2010 alone, 32 PWR fuel rods were discharged in the United States region that had failed due to fretting-related conditions. To eliminate this longstanding industry challenge, a suite of fuel products developed around the HTP (High Thermal Performance) spacer platform were implemented. The HTP grid design, with its multiple line contacts, serves to cradle the fuel rod and dampen vibrations in the presence of challenging flow conditions. When coupled with the Alloy 718 HMP (High Mechanical Performance) lower grid, HTP fuel has never experienced a GTRF failure. The AREVA NP's commitment to fuel reliability is successful: in 2010 a total of 41 failed fuel rods were discharged from reactors in the United States whereas in 2015 no failed fuel rods were discharged out of the approximately 1.3 million fuel rods in operation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Assessment on Transport of Radioactive Species from Nuclear Facilities - 17079

It is generally recognized that radioactive nuclides are most hazardous fission products that could be released in the event of reactor accidents. The reactor coolant system of a pressurized water reactor (PWR) nuclear plant exhibits radioactivity from various sources. These radiation sources consist of the fission products from fuel element and activated products from corrosion products. The complex infrastructure of the processes does not allow detailed measurement of activity until after the reactor is shutdown. All of the components that require dismantling will be radioactive which was caused by neutron activation during operation, contamination by corrosion products, contamination by damaged by fuel rods and leaks by equipment. Due mainly to the various operation modes and their aging, there are the increasing needs to carry out repair works that are not sufficiently provided for by the original design. Many difficulties are involved in these tasks, namely, high radiation doses, cramped areas, hard to reach components, coupled with stringent quality conditions. The need to simulate the behavior of corrosion products in a nuclear power plant environment has attracted many researchers' attention. It has performed the in-depth reviews of the various theories and physics associated with the corrosion products transportation, the laboratory loop testing, and the field measurements in operating plants. Before we start the decommissioning of nuclear power plants, workers, the public and the environment shall be properly protected from radiation hazards. For this purpose, a safety assessment should be carried out relating to the potential hazards that may occur during the decommissioning. The radiological hazards involved in the decommissioning activities also should be identified, and be taken into account in the safety assessment. The radiation conditions of the primary circuit are determined by the activity of corrosion and fission products that have accumulated on the internal surfaces of the components. Therefore the estimation of contamination on the components is very important and, may be the first step in the reactor operation and decommissioning of components. The predominant radionuclide in the PWR primary coolant is Co-60, although Co-58 contributes significantly to radioactivity level at the early stage of a reactor operation. Since Co-60 is produced from the in-core Co-58, which is the source of cobalt in a reactor coolant system, many researchers have investigated its transmutation in the core, its transport around the system, and its subsequent deposition on surfaces. The major parameter influencing the behavior of radioactivity, such as Co-60 in the coolant, is the corrosion product oxides. The objective of this work is to analyze the corrosion product activity transported in the primary circuit by using a multi-region model. This model, which is incorporated with the mass and activity transport between the dissolved corrosion products in the coolant and the surface, describes the specific activity of corrosion products in coolant and on the surfaces according to the operation modes as well as decommissioning stage. In order to evaluate the analysis of the corrosion products in an integral type reactor, a multi-region mass balance model is applied. The specific activities of the various species on the surface of core and steam generator throughout the effective full power hours, 15,000 hours, are simulated for the various modes of operations. As a result, the specific activities of corrosion products from the surface of primary circuit were shown as very low compared to those of other commercial nuclear power plants. In this simulated reactor, a significant reduction of specific activities from the activated corrosion products is obtained due to the introduction of titanium alloy to the steam generator tube and the avoidance of boric acid induced corrosion. From this result we conclude that we are able to predict the level of radioactive nuclides generated by corrosion products in a primary circuit according to the various modes of operations by using multi-region model. In this point of view it is concluded that this multi-region model can be used as an engineering tool for analysis of the corrosion products within the primary coolant for the nuclear power plants. It is also considered that it is possible to extend to a calculation tool for estimating the radiological hazards involved in the decommissioning activities in terms of safety assessment. (authors)

07 ISOTOPE AND RADIATION SOURCES↗

Feasibility studies for the design of disposal vaults for multi-purpose containers (MPCs): construction, operation, ventilation and management of heat - 15175

The Nuclear Decommissioning Authority (NDA) subsidiary, Radioactive Waste Management Ltd (RWM) is responsible for the safe implementation of a Geological Disposal Facility (GDF) for radioactive waste in the UK. As part of their generic programme to underpin the planned designs for a GDF, work is ongoing to explore a range of possible geological disposal concepts. This work developed GDF concept designs for Multi-Purpose Containers (MPC) disposal in the generic host rock types considered: higher strength (crystalline), lower strength sedimentary (sedimentary / clay formations) and evaporite rocks. This paper is specific to concepts for the disposal of MPC for Pressurised Water Reactor (PWR) spent nuclear fuel (SF). The key outcomes of the feasibility studies to improve the understanding of the MPC disposal concept and the specific challenges to construct, operate, ventilate, manage heat and backfill associated with this concept are summarised in this paper. The management of the high loading of radiogenic heat (from 12 PWR SF assemblies in MPCs compared to 4 in 'standard' disposal containers) during an extended open phase (delayed backfilling of the disposal area) of up to 300 years was investigated. The concept designs developed demonstrate it is feasible to construct, operate and ventilate disposal vaults to accommodate open 'storage' periods required for transitional thermal decay of high heat generating waste in higher strength and lower strength sedimentary host rock types considered by RWM. This work focused on developing two contrasting disposal concepts which are applicable to both higher strength and lower strength rock environments; both of which illustrate how vault temperature, stability and groundwater inflows can be controlled to delay backfilling and allow MPC package thermal output to decrease. MPC disposal in evaporite rock does not require a cooling period due to its high thermal conductivity and favourable performance at higher temperatures; therefore the concept developed for this rock includes immediate backfilling of disposal tunnels. A clear understanding of the interactions and limitations associated with heat management during the open period was developed by investigation of a 'Heating Ventilation and Air-Conditioning System' (HVAC). It was concluded that removal of heat from the disposal tunnels / vaults is feasible, but introduces significant operational complexity. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Development of the computer code for multi-calculations of source term of spent fuel - 15351

Many PWR spent fuels have been transferred between the neighboring nuclear power plants at Kori, Hanbit, Hanwul site, and from nuclear power plant to the KAERI(Korea Atomic Energy Research Institute) for the research purpose in Korea. In case of the PHWR type spent fuels, these have been transferred from the spent fuel pool to an on-site dry storage facility. Total radioactivity of spent fuels has to be calculated before transport in advance by the regulation requirement. In case of PWR, KN-12 transport cask can transfer 12 spent fuel assemblies at one time and in case of PHWR, Hi-STAR 63 transport cask can transfer 120 spent fuel assemblies at one time. Therefore, total radioactivity of all transported spent fuel assemblies that are transported generally are calculated by using the ORIGEN-ARP to meet this regulatory requirement. Basically, ORIGEN-ARP calculates the one fuel assembly at one time. SCALE code including this code provides the batch mode to perform the multi-calculations of the source term. In this study, in order to use the batch mode of ORIGEN-ARP, ARP-auto program was developed to generate input files and batch file of ORIGEN-ARP automatically and to make the summary file extracting the result from output files of ORIGEN-ARP. This code enhances the efficiency at the field. The working time to complete the calculation of source terms of 120 spent fuel assemblies take only 20 minutes. In order to confirm the credibility of this code, total radioactivity of 12 spent fuel assemblies of 17x17 Westinghouse type were calculated and compared to the previous result. The initial enrichments of these spent fuels are 3.46 ∼ 3.50 w/o and burnups are 29 ∼ 43 GWD/MTU. As the results, the relative errors are about 0.9 ∼ 3.0%. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Development of disposal container designs for disposal of high level waste and legacy spent fuel in the UK - 15471

Radioactive Waste Management Limited (RWM), a fully owned subsidiary of the Nuclear Decommissioning Authority (NDA), is responsible for the implementation of geological disposal in the UK. Three illustrative concepts of a geological disposal facility (GDF), corresponding to three generic geological environments - higher strength rock, lower strength sedimentary rock and evaporite rock - have been developed to demonstrate the viability of geological disposal of intermediate level waste, high level waste and spent fuel. It is envisaged that HLW which has been encapsulated in Waste Vitrification Plant (WVP) canisters, advanced gas-cooled reactor (AGR) SF which has been stripped of their spacers and packaged into slotted fuel cans, and PWR SF will be packaged into disposal containers for disposal. A set of schematic designs of these disposal containers was developed in the late 2000's. The design concept for the higher strength rock environment was based on the joint Posiva/SKB disposal container design, and the design concept for the lower strength sedimentary rock and evaporate rock illustrative environments was based on the disposal container concept from Switzerland's National Cooperative for the Disposal of Radioactive Waste (Nagra). The size, mass and dimensions of the disposal containers in the scheme designs vary significantly. The construction method and the lid closing method also vary between the disposal containers for the different waste contents. A design study has indicated that optimization of the number of HLW WVP canisters and the number of AGR slotted fuel cans in the disposal containers, standardizing construction method and closure arrangement across the containers for each geology type, providing handling features at both ends of the disposal container, and balancing of shielding around the containers, could bring significant advantage to the overall GDF programme by reducing the number of disposal containers, reducing GDF footprint, and reducing the extent of excavations, spoil generated and materials that are required for construction. A project to develop the scheme designs to conceptual level was carried in 2011 to 2013. In this project, the above changes were taken into account, technical underpinning of the designs was carried out and manufacturing method was considered. Two disposal container variants for different host rock environments have been developed: - Variant 1, for compatibility with the higher strength rock illustrative disposal system design. This is constructed from copper, with a cast iron insert and is based on the joint Posiva/SKB disposal container design. - Variant 2, for compatibility with the lower strength sedimentary rock and evaporite rock illustrative disposal system designs. This is a steel container based on the NAGRA disposal container design. Each variant has three internal configurations to accommodate 3 HLW vitrified canisters, 16 consolidated cans of AGR SF and 4 PWR spent fuel assemblies. These designs have been shown to bring significant benefit to the GDF designs, bringing a significant reduction to the operating programme and GDF programme cost, including reducing the number of disposal containers by 33% for HLW, 50% for AGR SF and reducing the size of the GDF footprint by 25%. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗