Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PHASE CONTROL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

Near-infrared resonance-mediated chirp control of a coherently generated broadband deep-ultraviolet spectrum

We investigate the use of shaped near-infrared (NIR) femtosecond pulses to control the generation of coherent broadband deep-ultraviolet (DUV) radiation in an atomic resonance-mediated (2+1) three-photon excitation to a broad far-from-resonance continuum. Previously, we have shown control over the total emitted DUV yield. Here, we experimentally demonstrate phase control over the spectral characteristics (central frequency and bandwidth) of the emitted broadband DUV radiation. It is achieved by tuning the linear chirp applied to the exciting NIR femtosecond pulse. The study is conducted with Na vapor.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Digital voltage-controlled oscillator

Digital voltage-controlled oscillator generates a variable frequency signal controlled linearly about a center frequency with high stability and is phase controlled by an applied voltage. Integration ahead of the digital circuitry provides linear operation with control voltage having appreciable noise components.

Saliga, T. V.↗

Active damping of modal vibrations by force apportioning

The theory and numerical simulation of active structural damping is described which requires few discrete control thrusters positioned on the structure. A particular apportioning of coherently phased control forces is applied for each vibration mode which is to be damped; this strongly affects the damped vibration mode, while minimally exciting all other modes. The force apportioning used is that which would tune a target mode if the structure was being shaken in a model vibration test. In contrast to model testing, the forces are varied temporally so as to dampen, rather than excite, the target mode(s).

Hallauer, W. L., Jr.↗

In Situ/Operando Probing of Dynamic Phase Structures of Alumina‐Supported Ultrasmall Copper‐Gold Alloy Nanoparticles Under Reaction Conditions

Abstract The ability to control phase structures and surface sites of ultrasmall alloy nanoparticles under reaction conditions is essential for preparing catalysts by design. This is, however, challenging due to limited understanding of the atomic‐scale phases and their correlation with the ensemble‐averaged structures and activities of catalysts during catalytic reactions. We reveal here a dynamic structural stability of alumina‐supported ultrasmall and equiatomic copper‐gold alloy nanoparticles under reaction conditions as a model system in the in situ/operando study. In situ atomic‐scale morphological tracking under oxygen reveals temperature‐dependent dynamic crystalline‐amorphous dual‐phase structures, showing dynamic stability over an elevated temperature range. This atomic‐scale dynamic phase stability coincides with a “conversion plateau” observed for carbon monoxide oxidation on the catalyst. It is substantiated by the stable lattice ordering/disordering structures and surface sites with oscillatory characteristics shown by operando ensemble‐average structural tracking of the catalyst during the oxidation reaction. The understanding of the atomic‐scale dynamic phase structures in correlation with the ensemble‐average dynamic ordering/disordering phase structures and surface sites provides fresh insights into the unique synergy of the supported alloy nanoparticles. This understanding has implications for the design and structural tuning of active and stable ultrasmall alloy catalysts under elevated temperatures.

Chemistry↗

Nanodiamond‐Palladium Core–Shell Organohybrid Synthesis: A Mild Vapor‐Phase Procedure Enabling Nanolayering Metal onto Functionalized sp 3 ‐Carbon

Abstract A novel approach for the bottom‐up construction of hybrid organic–inorganic nanocomposites with an intimate arrangement between sp 3 ‐carbon 3D molecular‐size nanodiamonds (diamondoids) and a coated palladium surface as nanolayer is reported. The construction process is conducted stepwisely from the gas phase, using first controlled vapor‐phase self‐assembly of tailor‐made functionalized diamantane derivatives, followed by low‐temperature (45 °C) chemical vapor deposition of an organometallic complex in a reducing H 2 atmosphere over the self‐assembled diamondoid scaffold. The use of self‐assemblies of primary diamantane phosphine and phosphine oxide, which are produced with high structural uniformity and reproducibility, yields new hybrid diamondoid‐palladium materials incorporating PdOPHdiamantane bonding motifs. Additional investigations provide evidence for a very challenging issue in the intimate construction of sp 3 ‐C/metal scaffolds. Scanning electron microscopy and transmission electron microscopy microscopies combined with X‐ray photoelectron spectroscopy surface analysis and EDX bulk analysis confirm the formation of diamondoid‐palladium organohybrids with unique surface layering. The vapor phase‐controlled mild synthetic process allows excellent control over nanocomposite formation and morphology from molecular‐level modifications. As such, this bottom‐up composite building process bridges scales from the molecular (functionalized diamondoids) over nanoscopic (self‐assemblies) to microscopic regime (hybrids), in the challenging association of transition metals with an electronically saturated sp 3 ‐carbon organic host material.

Gunawan, Maria A.↗

Local electric field direct writing – Electron-beam lithography and mechanism

Local electric field induced by a focused electron probe in silicate glass thin films is evaluated in this paper by the migration of cations. Extremely strong local electric fields can be obtained by the focused electron probe from a scanning transmission electron microscope. As a result, collective atomic displacements occur. This newly revised mechanism provides an efficient tool to write patterned nanostructures directly, and thus overcome the low efficiency of the conventional electron-beam lithography. Applying this technique to silicate glass thin films, as an example, a grid of rods of nanometer dimension can be efficiently produced by rapidly scanning a focused electron probe. This nanopatterning is achieved through swift phase separation in the sample, without any post-development processes. The controlled phase separation is induced by massive displacements of cations (glass modifiers) within the glass-former network, driven by the strong local electric fields. The electric field is induced by accumulated charge within the electron probed region, which is generated by the excitation of atomic electrons by the incident electron. Throughput is much improved compared to other scanning probe techniques. Finally, the half-pitch spatial resolution of nanostructure in this particular specimen is 2.5 nm.

36 MATERIALS SCIENCE↗

Continuous control of phase-locked-loop bandwidth

Tracking loop filter with continuous bandwidth control smooths transition from wide to narrow band. Circuit was designed for Space Shuttle where bandwidth varied between 320 Hz for acquisition and 20 Hz for tracking. Field-effect transitor (FET) acts as voltage controlled variable resistance, changing time constant of filter between phase detector and voltage-controlled oscillator in phase-locked loop.

Motal, G. W.↗

Multiple Supersonic Phase Fronts Launched at a Complex-Oxide Heterointerface

Selective optical excitation of a substrate lattice can drive phase changes across heterointerfaces. This phenomenon is a nonequilibrium analogue of static strain control in heterostructures and may lead to new applications in optically controlled phase change devices. Here, we make use of time-resolved nonresonant and resonant x-ray diffraction to clarify the underlying physics and to separate different microscopic degrees of freedom in space and time. We also measure the dynamics of the lattice and that of the charge disproportionation in NdNiO 3 , when an insulator-metal transition is driven by coherent lattice distortions in the LaAlO 3 substrate. We find that charge redistribution propagates at supersonic speeds from the interface into the NdNiO 3 film, followed by a sonic lattice wave. Our results establish a hierarchy of events for ultrafast control at complex-oxide heterointerfaces, when combined with measurements of magnetic disordering and of the metal-insulator transition.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

NEMA-Phase Compliant Traffic Signal Controller Module in SUMO

The controller modules in SUMO use a stage-based control structure. A phase is defined as a stage of all allowed movements at a time instance. However, traffic signal controllers used in North America widely use National Electrical Manufacturers Association (NEMA) phase definition. A NEMA phase is defined by a certain flow movement at an intersection. At one time, more than one NEMA phase could happen together as long as they do not conflict with each other. We can visualize the NEMA phases and timings in Ring-and-Barrier structured NEMA diagrams. For one controller, only one phase from a ring can be activated at a time. Phases from different rings could be activated together as long as they are not from the different sides of a barrier. When a controller is operated in fixed-time control mode, we can model the NEMA phase timing as a corresponding stage-based control timing without any issues. When introducing actuation into the signal control, a Ring-and-Barrier structured traffic signal controller can be more flexible than stage-based controller by allowing different possible phase combinations. We made two efforts in modeling Ring-and-Barrier structured controllers in SUMO. One is to translate a NEMA phases timing into SUMO-readable phases and timings as an additional file for SUMO. This translation worked well for fixed-time control. To model actuated control and coordinated actuated control, we augmented the SUMO source code by adding a Ring-and-Barrier structured controller module. This module could implement traffic signal timing from controllers using NEMA phases. We also augmented TraCI to be able to set new NEMA phase timings during simulations. We examined the Ring-and-Barrier structured traffic signal controller module by both visually observing the simulation animations and the simulation records. The developed control module can model the generalized Ring-and-Barrier structured traffic signal timing that is used in North America. SEE: https://github.com/eclipse/sumo/blob/main/src/microsim/traffic_lights/NEMAController.cpp

Wang, Qichao↗

Solubility Control of Technetium Release from Saltstone by Tc02•xH20

Saltstone leaching experiments were conducted using a modified single-pass flow-through method under anoxic conditions. The analytical results of leachates collected from these experiments were evaluated using thermodynamic modeling to determine if the data were consistent with potential solubility controlling phases. The results demonstrate that technetium concentrations in water in contact with Saltstone under anoxic conditions is controlled by the solubility of TcO2•xH2O (likely TcO2•1.6H2O). In our system equilibrium solubility appears to have been reached within two weeks at a concentration of approximately 1.5 x 10-6 M. This concentration is likely to vary as the composition of Saltstone pore fluid evolves over time. As the pH goes from the initial high values (~12.5-13) to lower values, the solubility of technetium will decrease significantly. The thermodynamic data used to determine the solubility of TcO2•1.6H2O were taken from the tabulation of critically selected thermodynamic data determined by the Nuclear Energy Agency. Solid phase characterization to demonstrate the presence of TcO2•xH2O was not possible due to the low concentrations of technetium in our samples. Previous solid phase characterization studies with cementitious waste forms that were very similar to our Saltstone samples as well as reaction products derived from reductive immobilization of TcO4- by amorphous FeS clearly indicate the presence of TcO2 with varying degrees of hydration. Although, the presence of TcSx or other reduced technetium sulfide phases in our samples cannot be ruled out, release of technetium from Saltstone will be controlled by TcO2•1.6H2O because of its higher solubility. Our results clearly demonstrate that the release mechanism of technetium from Saltstone under reducing conditions is solubility controlled by TcO2•xH2O (likely TcO2•1.6H2O); however, distribution coefficients (Kds), that describe sorption and not solubility, were calculated for comparison with past literature values. After 84 days of reaction under anoxic conditions, the average Kd value for technetium was determined to be 610 mL/g. This value is similar to a value determined previously for a similar saltstone sample under reducing conditions at 56 days (712 ± 81 mL/g).

Saltstone↗

Amphibian and reptile community response to coarse woody debris manipulations in upland loblolly pine (Pinus taeda) forests.

Coarse woody debris (CWD) has been identified as a key microhabitat component for groups that are moisture and temperature sensitive such as amphibians and reptiles. However, few experimental manipulations have quantitatively assessed amphibian and reptile response to varying CWD volumes within forested environments. We assessed amphibian and reptile response to large-scale, CWD manipulation within managed loblolly pine stands in the southeastern Coastal Plain of the United States from 1998 to 2005. Our study consisted of two treatment phases: Phase I treatments included downed CWD removal (removal of all downed CWD), all CWD removal (removal of all downed and standing CWD), pre-treatment snag, and control; Phase II treatments included downed CWD addition (downed CWD volume increased 5-fold), snag addition (standing CWD volume increased 10-fold), all CWD removal (all CWD removed), and control. Amphibian and anuran capture rates were greater in control than all CWD removal plots during study Phase I. In Phase II, reptile diversity and richness were greater in downed CWD addition and all CWD removal than snag addition treatments. Capture rate of Rana sphenocephala was greater in all CWD removal treatment than downed CWD addition treatment. The dominant amphibian and snake species captured are adapted to burrowing in sandy soil or taking refuge under leaf litter. Amphibian and reptile species endemic to upland southeastern Coastal Plain pine forests may not have evolved to rely on CWD because the humid climate and short fire return interval have resulted in historically low volumes of CWD.

60 APPLIED LIFE SCIENCES↗

Dynamic Modeling of Sequential Service Restoration in Islanded Single Master Microgrids

This paper presents a methodology for generating restoration sequences in distribution systems and microgrids with emphasis on deriving optimal switching times for remote control switches (RCS). Microgrid architecture considered are assumed to be operating in islanded single master mode. Control methods for handling the unbalance inherent in distribution systems using single-phase controlled PQ inverters were developed and incorporated in the proposed method. The problem of considering simultaneously both energy optimization and dynamic stability of the system, which is lacking in existing methods, was addressed by studying the transient behavior of microgrids based on extended EMTP simulations and then approximate and incorporate these behaviors into the optimization formulation for restoration. The approach is based on multi-objective optimization of final restored load and total restoration time. The methodology was studied on a modified IEEE 123 node test feeder. An EMTP simulation in PSCAD of the formed microgrids was used to validate the accuracy of the dynamic and steady-state characteristics of the resulting systems. By considering the transient behavior of DGs during restoration, a better restoration sequence that does not trigger protection relays could be realized.

42 ENGINEERING↗

Shuttle avionics software trials, tribulations and success

The early problems and the solutions developed to provide the required quality software needed to support the space shuttle engine development program are described. The decision to use a programmable digital control system on the space shuttle engine was primarily based upon the need for a flexible control system capable of supporting the total engine mission on a large complex pump fed engine. The mission definition included all control phases from ground checkout through post shutdown propellant dumping. The flexibility of the controller through reprogrammable software allowed the system to respond to the technical challenges and innovation required to develop both the engine and controller hardware. This same flexibility, however, placed a severe strain on the capability of the software development and verification organization. The overall development program required that the software facility accommodate significant growth in both the software requirements and the number of software packages delivered. This challenge was met by reorganization and evolution in the process of developing and verifying software.

Henderson, O. L.↗

Dissolution Kinetics of Synthetic and Natural Meta-Autunite Minerals, X 3-n (n)+ [(UO₂)(PO₄)]₂ · xH₂O, Under Acidic Conditions

Mass transport within the uranium geochemical cycle is impacted by the availability of phosphorous. In oxidizing environments, in which the uranyl (UO 2 2+ ) ionic species is typically mobile, formation of sparingly soluble uranyl phosphate minerals exert a strong influence on uranium transport. Autunite group minerals, X 3-n (n)+ [(UO 2 )(PO 4 )] 2 · xH 2 0, have been identified as the long-term uranium controlling phases in many systems of geochemical interest. Anthropogenic operations related to uranium mining operations have created acidic environments, exposing uranyl phosphate minerals to low pH groundwaters. Investigations regarding the dissolution behavior of autunite group minerals under acidic conditions have not been reported; consequently, knowledge of the longevity of uranium controlling solids is incomplete. The purpose of this investigation was to: 1) quantify the dissolution kinetics of natural calcium and synthetic sodium meta-autunite, Ca[(UO 2 ) 2 (PO 4 ) 2 ] · 3H 2 O, under acidic conditions, 2) measure the effect of temperature and pH on meta-autunite mineral dissolution, and 3) investigate the formation of secondary uranyl phosphate phases as long-term controls on uranium migration. Single-pass flow-through (SPFT) dissolution tests were conducted over the pH range of 2 to 5 and from 5° to 70°C. Results presented here illustrate meta-autunite dissolution kinetics are strongly dependent on pH, but are relatively insensitive to temperature variations. In addition, the formation of secondary uranyl-phosphate phases such as, uranyl phosphate, (UO 2 ) 3 (PO 4 ) 2 · x H 2 O, may serve as a secondary phase limiting the migration of uranium in the environment.

58 GEOSCIENCES↗

NASA Tech Briefs, July 2006

Topics covered include: Airport Remote Tower Sensor Systems; Implantable Wireless MEMS Sensors for Medical Uses; Embedded Sensors for Measuring Surface Regression; Coordinating an Autonomous Earth-Observing Sensorweb; Range-Measuring Video Sensors; Stability Enhancement of Polymeric Sensing Films Using Fillers; Sensors for Using Times of Flight to Measure Flow Velocities; Receiver Would Control Phasing of a Phased-Array Antenna; Modern Design of Resonant Edge-Slot Array Antennas; Carbon-Nanotube Schottky Diodes; Simplified Optics and Controls for Laser Communications; Coherent Detection of High-Rate Optical PPM Signals; Multichannel Phase and Power Detector; Using Satellite Data in Weather Forecasting: I; Using Dissimilarity Metrics to Identify Interesting Designs; X-Windows PVT Widget Class; Shuttle Data Center File-Processing Tool in Java; Statistical Evaluation of Utilization of the ISS; Nanotube Dispersions Made With Charged Surfactant; Aerogels for Thermal Insulation of Thermoelectric Devices; Low-Density, Creep-Resistant Single-Crystal Superalloys; Excitations for Rapidly Estimating Flight-Control Parameters; Estimation of Stability and Control Derivatives of an F-15; Tool for Coupling a Torque Wrench to a Round Cable Connector; Ultrasonically Actuated Tools for Abrading Rock Surfaces; Active Struts With Variable Spring Stiffness and Damping; Multiaxis, Lightweight, Computer-Controlled Exercise System; Dehydrating and Sterilizing Wastes Using Supercritical CO2; Alpha-Voltaic Sources Using Liquid Ga as Conversion Medium; Ice-Borehole Probe; Alpha-Voltaic Sources Using Diamond as Conversion Medium; White-Light Whispering-Gallery-Mode Optical Resonators; Controlling Attitude of a Solar-Sail Spacecraft Using Vanes; and Wire-Mesh-Based Sorber for Removing Contaminants from Air.

Source record↗