Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Numerical optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

Optimized Shapes of Ocsillating Resonators for Generating High-Amplitude Pressure Waves

It is well known that the resonator geometry strongly influences the resonant frequencies of an acoustical resonator and the generated nonlinear standing pressure waveform. Maximizing the ratio of maximum to minimum gas pressure at an end of an oscillating resonator by optimizing the cavity contour is investigated numerically. A quasi-Newton type scheme is used to find optimized axisymmetric resonator shapes to achieve the maximum pressure compression ratio. The acoustical field is solved using a one-dimensional model, and the resonance frequency shift and hysteresis effects are obtained through an automation scheme based on continuation methods. Results are presented from optimizing cone, horn-cone, and cosine resonator geometries. Significant performance improvement is found in the optimized shapes over others previously published. Different optimized shapes are found when starting with different initial guesses, indicating multiple local extrema. The numerical model is validated by comparing with the experimental results of a horn-cone shaped resonator.

Li, Xiao-Fan↗

Three-dimensional canard-wing shape optimization in aircraft cruise and maneuver environments

This paper demonstrates a numerical technique for canard-wing shape optimization at two operating conditions. For purposes of simplicity, a mean surface wing paneling code is employed for the aerodynamic calculations. The optimization procedures are based on the method of feasible directions. The shape functions for describing the thickness, camber, and twist are based on polynomial representations. The primary design requirements imposed restrictions on the canard and wing volumes and on the lift coefficients at the operating conditions. Results indicate that significant improvements in minimum drag and lift-to-drag ratio are possible with reasonable aircraft geometries. Calculations were done for supersonic speeds with Mach numbers ranging from 1 to 6. Planforms were mainly of a delta shape with aspect ratio of 1.

De Silva, B. M. E.↗

Simultaneous structure/control optimization of large flexible spacecraft

This paper presents an approach to the simultaneous optimal design of a structure and control system for large flexible spacecrafts based on realistic objective function and constraints. The weight or total cost of structure and control system is minimized subject to constraints on the magnitude of response to a given disturbance involving both rigid-body and elastic modes. A nested optimization technique is developed to solve the combined problem. As an example, simple beam-like spacecraft under a steady-state white-noise disturbance force is investigated and some results of optimization are presented. In the numerical examples, the stiffness distribution, the location of controller and the control gains are optimized. Direct feedback control and linear quadratic optimal control laws are used with both inertial and non-inertial disturbing force. It is shown that the total cost is sensitive to the overall structural stiffness so that a simultaneous optimization of the structure and control system is indeed useful.

Onoda, Junjiro↗

Reducing neural network training time with parallel processing

Obtaining optimal solutions for engineering design problems is often expensive because the process typically requires numerous iterations involving analysis and optimization programs. Previous research has shown that a near optimum solution can be obtained in less time by simulating a slow, expensive analysis with a fast, inexpensive neural network. A new approach has been developed to further reduce this time. This approach decomposes a large neural network into many smaller neural networks that can be trained in parallel. Guidelines are developed to avoid some of the pitfalls when training smaller neural networks in parallel. These guidelines allow the engineer: to determine the number of nodes on the hidden layer of the smaller neural networks; to choose the initial training weights; and to select a network configuration that will capture the interactions among the smaller neural networks. This paper presents results describing how these guidelines are developed.

Rogers, James L., Jr.↗

Procedures for shape optimization of gas turbine disks

Two procedures, the feasible direction method and sequential linear programming, for shape optimization of gas turbine disks are presented. The objective of these procedures is to obtain optimal designs of turbine disks with geometric and stress constraints. The coordinates of the selected points on the disk contours are used as the design variables. Structural weight, stress and their derivatives with respect to the design variables are calculated by an efficient finite element method for design senitivity analysis. Numerical examples of the optimal designs of a disk subjected to thermo-mechanical loadings are presented to illustrate and compare the effectiveness of these two procedures.

Cheu, Tsu-Chien↗

A Preconditioning Method for Shape Optimization Governed by the Euler Equations

We consider a classical aerodynamic shape optimization problem subject to the compressible Euler flow equations. The gradient of the cost functional with respect to the shape variables is derived with the adjoint method at the continuous level. The Hessian (second order derivative of the cost functional with respect to the shape variables) is approximated also at the continuous level, as first introduced by Arian and Ta'asan (1996). The approximation of the Hessian is used to approximate the Newton step which is essential to accelerate the numerical solution of the optimization problem. The design space is discretized in the maximum dimension, i.e., the location of each point on the intersection of the computational mesh with the airfoil is taken to be an independent design variable. We give numerical examples for 86 design variables in two different flow speeds and achieve an order of magnitude reduction in the cost functional at a computational effort of a full solution of the analysis partial differential equation (PDE).

Arian, Eyal↗

Mixed Integer Programming and Heuristic Scheduling for Space Communication

Optimal planning and scheduling for a communication network was created where the nodes within the network are communicating at the highest possible rates while meeting the mission requirements and operational constraints. The planning and scheduling problem was formulated in the framework of Mixed Integer Programming (MIP) to introduce a special penalty function to convert the MIP problem into a continuous optimization problem, and to solve the constrained optimization problem using heuristic optimization. The communication network consists of space and ground assets with the link dynamics between any two assets varying with respect to time, distance, and telecom configurations. One asset could be communicating with another at very high data rates at one time, and at other times, communication is impossible, as the asset could be inaccessible from the network due to planetary occultation. Based on the network's geometric dynamics and link capabilities, the start time, end time, and link configuration of each view period are selected to maximize the communication efficiency within the network. Mathematical formulations for the constrained mixed integer optimization problem were derived, and efficient analytical and numerical techniques were developed to find the optimal solution. By setting up the problem using MIP, the search space for the optimization problem is reduced significantly, thereby speeding up the solution process. The ratio of the dimension of the traditional method over the proposed formulation is approximately an order N (single) to 2*N (arraying), where N is the number of receiving antennas of a node. By introducing a special penalty function, the MIP problem with non-differentiable cost function and nonlinear constraints can be converted into a continuous variable problem, whose solution is possible.

Lee, Charles H.↗

Range-Specific High-resolution Mesoscale Model Setup

This report summarizes the findings from an AMU task to determine the best model configuration for operational use at the ER and WFF to best predict winds, precipitation, and temperature. The AMU ran test cases in the warm and cool seasons at the ER and for the spring and fall seasons at WFF. For both the ER and WFF, the ARW core outperformed the NMM core. Results for the ER indicate that the Lin microphysical scheme and the YSU PBL scheme is the optimal model configuration for the ER. It consistently produced the best surface and upper air forecasts, while performing fairly well for the precipitation forecasts. Both the Ferrier and Lin microphysical schemes in combination with the YSU PBL scheme performed well for WFF in the spring and fall seasons. The AMU has been tasked with a follow-on modeling effort to recommended local DA and numerical forecast model design optimized for both the ER and WFF to support space launch activities. The AMU will determine the best software and type of assimilation to use, as well as determine the best grid resolution for the initialization based on spatial and temporal availability of data and the wall clock run-time of the initialization. The AMU will transition from the WRF EMS to NU-WRF, a NASA-specific version of the WRF that takes advantage of unique NASA software and datasets. 37

Watson, Leela R.↗

Duct liner optimization for turbomachinery noise sources

An acoustical field theory for axisymmetric, multisectioned lined ducts with uniform flow profiles was combined with a numerical minimization algorithm to predict optimal liner configurations having one, two, and three sections. Source models studied include a point source located on the axis of the duct and rotor/outlet-stator viscous wake interaction effects for a typical research compressor operating at an axial flow Mach number of about 0.4. For this latter source, optimal liners for equipartition-of energy, zero-phase, and least-attenuated-mode source variations were also calculated and compared with exact results. It is found that the potential benefits of liner segmentation for the attenuation of turbomachinery noise is greater than would be predicted from point source results. Furthermore, effective liner design requires precise knowledge of the circumferential and radial modal distributions.

Lester, H. C.↗

The design and development of a mixer compound exhaust system for a quiet clean general aviation turbofan

Lower engine fuel consumption has become a dominant factor in turbofan engine design due to rapidly increasing fuel costs. One engine component with a large impact on engine performance is the exhaust system. Previous exhaust system studies have demonstrated the significant exhaust system efficiency gains available through mixing of the core and bypass flows. Typically, a large, costly rig and engine program are required to develop and optimize these gains. The purpose of this paper is to present the results of the low-cost design system used for the quiet, clean general aviation turbofan mixer nozzle design and development. The scale model and full-scale engine test results confirm the predicted 3 to 5% reduction in cruise fuel consumption. This unique design system, which is based on integrating advanced three-dimensional viscous numerical methods with empirical optimization techniques, is summarized and detailed comparisons with test data are presented. The ability to accurately predict relative performance of mixer systems with substantially reduced development time and cost savings is demonstrated.

Blackmore, W. L.↗

Optimal detumbling of a large manned spacecraft using an internal moving mass

This investigation deals with the use of a movable mass control system to stabilize a tumbling asymmetric spacecraft about the maximum inertia axis. A first-order gradient optimization technique is used to minimize angular velocity components along the intermediate and minimum inertia axes, thus, permitting a wide range of initial guesses for mass position history. Motion of the control mass is along a linear track fixed in the vehicle. The control variable is taken as mass acceleration with respect to body coordinates. Motion is limited to defined quantities and a penalty function is used to insure a given range of positions. Numerical solutions of the optimization equations verify that minimum time detumbling is achieved with the largest permissible movable mass, length of linear track, and positions of the mass on the two coordinates perpendicular to the linear motion. The optimal method permits detumbling in about one-fourth the time when compared to a force control law formulation available in the literature.

Kunciw, B. G.↗

Optimal detumbling of a large manned spacecraft using an internal moving mass

The use of a movable mass control system to stabilize an arbitrarily tumbling asymmetric vehicle about the maximum inertia axis is considered. A first-order gradient optimization technique is used to minimize angular velocity components along the intermediate and minimum inertia axes. This method permits a wide range of initial guesses for mass position history. Motion of the control mass is along a linear track fixed in the vehicle. The control variable is taken as mass acceleration with respect to body coordinates. Motion is limited to defined quantities and a penalty function is used to insure a given range of positions. Numerical solutions of the optimization equations verify that minimum time detumbling is achieved with the largest permissible movable mass, length of linear track, and positions of the mass on the two coordinates perpendicular to the linear motion.

Kunciw, B. G.↗

A rotor optimization using regression analysis

The design and development of helicopter rotors is subject to the many design variables and their interactions that effect rotor operation. Until recently, selection of rotor design variables to achieve specified rotor operational qualities has been a costly, time consuming, repetitive task. For the past several years, Kaman Aerospace Corporation has successfully applied multiple linear regression analysis, coupled with optimization and sensitivity procedures, in the analytical design of rotor systems. It is concluded that approximating equations can be developed rapidly for a multiplicity of objective and constraint functions and optimizations can be performed in a rapid and cost effective manner; the number and/or range of design variables can be increased by expanding the data base and developing approximating functions to reflect the expanded design space; the order of the approximating equations can be expanded easily to improve correlation between analyzer results and the approximating equations; gradients of the approximating equations can be calculated easily and these gradients are smooth functions reducing the risk of numerical problems in the optimization; the use of approximating functions allows the problem to be started easily and rapidly from various initial designs to enhance the probability of finding a global optimum; and the approximating equations are independent of the analysis or optimization codes used.

Giansante, N.↗

An optimal control strategy for collision avoidance of mobile robots in non-stationary environments

An optimal control formulation of the problem of collision avoidance of mobile robots in environments containing moving obstacles is presented. Collision avoidance is guaranteed if the minimum distance between the robot and the objects is nonzero. A nominal trajectory is assumed to be known from off-line planning. The main idea is to change the velocity along the nominal trajectory so that collisions are avoided. Furthermore, time consistency with the nominal plan is desirable. A numerical solution of the optimization problem is obtained. Simulation results verify the value of the proposed strategy.

Kyriakopoulos, K. J.↗

Aeroelastic optimization of a panel in high Mach number supersonic flow.

Solution for a least-weight skin thickness distribution for a panel with a flutter parameter constraint. This panel weighs less than any similar constant thickness panel, but has the same critical supersonic panel flutter parameter. The panel rests on simple supports and is of sandwich construction. The span to chord ratio is large enough that the inertial, elastic, and aerodynamic behavior is one-dimensional. The Mach number is great enough that the aerodynamic forces acting on the upper panel surface may be accurately described by quasi-steady, linearized, supersonic aerodynamic theory. The final optimum design is obtained from theoretical and numerical methods adapted from optimal control theory. The results of this investigation show that the optimal panel thickness distribution is symmetric about the panel chord midpoint. Compared to a reference panel with constant thickness, optimum panels are found to be nearly 12% lighter.

Weisshaar, T. A.↗

Direct handling of equality constraints in multilevel optimization

In recent years there have been several hierarchic multilevel optimization algorithms proposed and implemented in design studies. Equality constraints are often imposed between levels in these multilevel optimizations to maintain system and subsystem variable continuity. Equality constraints of this nature will be referred to as coupling equality constraints. In many implementation studies these coupling equality constraints have been handled indirectly. This indirect handling has been accomplished using the coupling equality constraints' explicit functional relations to eliminate design variables (generally at the subsystem level), with the resulting optimization taking place in a reduced design space. In one multilevel optimization study where the coupling equality constraints were handled directly, the researchers encountered numerical difficulties which prevented their multilevel optimization from reaching the same minimum found in conventional single level solutions. The researchers did not explain the exact nature of the numerical difficulties other than to associate them with the direct handling of the coupling equality constraints. The coupling equality constraints are handled directly, by employing the Generalized Reduced Gradient (GRG) method as the optimizer within a multilevel linear decomposition scheme based on the Sobieski hierarchic algorithm. Two engineering design examples are solved using this approach. The results show that the direct handling of coupling equality constraints in a multilevel optimization does not introduce any problems when the GRG method is employed as the internal optimizer. The optimums achieved are comparable to those achieved in single level solutions and in multilevel studies where the equality constraints have been handled indirectly.

Renaud, John E.↗

An Integrated Control and Minimum Mass Structural Optimization Algorithm for Large Space Structures

A new approach is discussed for solving dual structural control optimization problems for high-order flexible space structures, where reduced-order structural models are employed and minimum mass designs are sought. For a given initial structural design, a quadratic control cost is minimized subject to a constant-mass constraint. The sensitivity of the optimal control cost with respect to the structural design variables is then determined and used to obtain successive structural redesigns, using a constrained gradient optimization algorithm. This process is repeated until the constrained control cost sensitivity becomes negligible. The minimum mass design is obtained by solving a sequence of neighboring optimal constant mass designs, where the sequence of optimal performance indices has a minimum at the optimal minimum mass design. A numerical example is presented which demonstrates that this new approach effectively addresses the problem of dual optimization for potentially very high-order structures.

Messac, A.↗

Recent experience in simultaneous control-structure optimization

To show the feasibility of simultaneous optimization as design procedure, low order problems were used in conjunction with simple control formulations. The numerical results indicate that simultaneous optimization is not only feasible, but also advantageous. Such advantages come at the expense of introducing complexities beyond those encountered in structure optimization alone, or control optimization alone. Examples include: larger design parameter space, optimization may combine continuous and combinatoric variables, and the combined objective function may be nonconvex. Future extensions to include large order problems, more complex objective functions and constraints, and more sophisticated control formulations will require further research to ensure that the additional complexities do not outweigh the advantages of simultaneous optimization. Some areas requiring more efficient tools than currently available include: multiobjective criteria and nonconvex optimization. Efficient techniques to deal with optimization over combinatoric and continuous variables, and with truncation issues for structure and control parameters of both the model space as well as the design space need to be developed.

Salama, M.↗