Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Monte Carlo Method”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

Thermal performance simulation of a solar cavity receiver under windy conditions

Solar cavity receiver plays a dominant role in the light-heat conversion. Its performance can directly affect the efficiency of the whole power generation system. A combined calculation method for evaluating the thermal performance of the solar cavity receiver is raised in this paper. This method couples the Monte-Carlo method, the correlations of the flow boiling heat transfer, and the calculation of air flow field. And this method can ultimately figure out the surface heat flux inside the cavity, the wall temperature of the boiling tubes, and the heat loss of the solar receiver with an iterative solution. With this method, the thermal performance of a solar cavity receiver, a saturated steam receiver, is simulated under different wind environments. The highest wall temperature of the boiling tubes is about 150 C higher than the water saturation temperature. And it appears in the upper middle parts of the absorbing panels. Changing the wind angle or velocity can obviously affect the air velocity inside the receiver. The air velocity reaches the maximum value when the wind comes from the side of the receiver (flow angle {alpha} = 90 ). The heat loss of the solar cavity receiver also reaches a maximum for the side-on wind. (author)

14 SOLAR ENERGY↗

Automated Variance Reduction Applied to Nuclear Well-Logging Problems

The Monte Carlo method enables detailed, explicit geometric, energy and angular representations, and hence is considered to be the most accurate method available for solving complex radiation transport problems. Because of its associated accuracy, the Monte Carlo method is widely used in the petroleum exploration industry to design, benchmark, and simulate nuclear well-logging tools. Nuclear well-logging tools, which contain neutron and/or gamma sources and two or more detectors, are placed in boreholes that contain water (and possibly other fluids) and that are typically surrounded by a formation (e.g., limestone, sandstone, calcites, or a combination). The response of the detectors to radiation returning from the surrounding formation is used to infer information about the material porosity, density, composition, and associated characteristics. Accurate computer simulation is a key aspect of this exploratory technique. However, because this technique involves calculating highly precise responses (at two or more detectors) based on radiation that has interacted with the surrounding formation, the transport simulations are computationally intensive, requiring significant use of variance reduction techniques, parallel computing, or both. Because of the challenging nature of these problems, nuclear well-logging problems have frequently been used to evaluate the effectiveness of variance reduction techniques (e.g., Refs. 1-4). The primary focus of these works has been on improving the computational efficiency associated with calculating the response at the most challenging detector location, which is typically the detector furthest from the source. Although the objective of nuclear well-logging simulations is to calculate the response at multiple detector locations, until recently none of the numerous variance reduction methods/techniques has been well-suited to simultaneous optimization of multiple detector (tally) regions. Therefore, a separate calculation is typically performed for each desired detector response. This paper summarizes recent work to apply and evaluate the effectiveness of deterministic-adjoint-based variance reduction methods, including a recently developed method for simultaneous optimization of multiple detectors, for two simple nuclear well-logging tool problems that have been widely used in the variance reduction literature. The computational effectiveness of the method for simultaneous optimization is also compared to the use of multiple, individually optimized simulations for these simple well-logging problems.

02 PETROLEUM↗

SCALE 6.2 Continuous-Energy TSUNAMI-3D Capabilities

The TSUNAMI (Tools for Sensitivity and UNcertainty Analysis Methodology Implementation) capabilities within the SCALE code system make use of sensitivity coefficients for an extensive number of criticality safety applications, such as quantifying the data-induced uncertainty in the eigenvalue of critical systems, assessing the neutronic similarity between different systems, quantifying computational biases, and guiding nuclear data adjustment studies. The need to model geometrically complex systems with improved ease of use and fidelity and the desire to extend TSUNAMI analysis to advanced applications have motivated the development of a SCALE 6.2 module for calculating sensitivity coefficients using three-dimensional (3D) continuous-energy (CE) Monte Carlo methods: CE TSUNAMI-3D. This paper provides an overview of the theory, implementation, and capabilities of the CE TSUNAMI-3D sensitivity analysis methods. CE TSUNAMI contains two methods for calculating sensitivity coefficients in eigenvalue sensitivity applications: (1) the Iterated Fission Probability (IFP) method and (2) the Contributon-Linked eigenvalue sensitivity/Uncertainty estimation via Track length importance CHaracterization (CLUTCH) method. This work also presents the GEneralized Adjoint Response in Monte Carlo method (GEAR-MC), a first-of-its-kind approach for calculating adjoint-weighted, generalized response sensitivity coefficients—such as flux responses or reaction rate ratios—in CE Monte Carlo applications. The accuracy and efficiency of the CE TSUNAMI-3D eigenvalue sensitivity methods are assessed from a user perspective in a companion publication, and the accuracy and features of the CE TSUNAMI-3D GEAR-MC methods are detailed in this paper.

42 ENGINEERING↗

New approach to creation of geometrical module for nuclear reactor neutron transport computer simulation analysis

This paper presents the new approach to creation of geometrical module for nuclear reactor neutron transport computer simulation analysis so called the differential cross method. It is elaborated for detecting boards between physical zones. It is proposed to use GMSH open source mesh editor extended by some features: a special option and a special kind of mesh (cubic background mesh).This method is aimed into Monte Carlo Method as well as for deterministic neutron transport methods. Special attention is attended for reactor core composed of a set of material zones with complicate geometrical boundaries. The idea of this approach is described. In general case method works for 3-D space. Algorithm of creation of the geometrical module is given. 2-D neutron transport benchmark-test for RBMK reactor cluster cell is described. It demonstrates the ability of this approach to provide flexible definition of geometrical meshing with preservation of curved surface or any level of heterogeneity. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

SCALE Monte Carlo Eigenvalue Methods and New Advancements

SCALE code system is developed and maintained by Oak Ridge National Laboratory to perform criticality safety, reactor analysis, radiation shielding, and spent fuel characterization for nuclear facilities and transportation/storage package designs. SCALE is a modular code system that includes several codes which use either Monte Carlo or discrete ordinates solution methodologies for solving relevant neutral particle transport equations. This paper describes some of the key capabilities of the Monte Carlo criticality safety codes within the SCALE code system.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Internal energy relaxation in shock wave structure

The Wang Chang-Uhlenbeck (WCU) equation is numerically integrated to characterize the internal structure of Mach 3 and Mach 5 shock waves in a gas with excitation in the internal energy states for the treatment of inelastic collisions. Elastic collisions are modeled with the hard sphere collision model and the transition rates for the inelastic collisions modified appropriately using probabilities based on relative velocities of the colliding particles. The collision integral is evaluated by the conservative discrete ordinate method [F. Tcheremissine, “Solution of the Boltzmann kinetic equation for high-speed flows,” Comput. Math. Math. Phys. 46, 315–329 (2006); F. Cheremisin, “Solution of the Wang Chang-Uhlenbeck equation,” Dokl. Phys. 47, 487–490 (2002)] developed for the Boltzmann equation. For the treatment of the diatomic molecules, the internal energy modes in the Boltzmann equation are described quantum mechanically given by the WCU equation. As a first step in the treatment of the inelastic collisions by the WCU equation, a two- and three-quantum system is considered to study the effect of the varying of (1) the inelastic cross section and (2) the energy gap between the quantum energy states. An alternative method, the direct simulation Monte Carlo method, is used for the Mach 3 shock wave to ensure the consistency of implementation in the two methods and there is an excellent agreement between the two methods. The results from the WCU implementation showed consistent trends for the Mach 3 and Mach5 standing shock waves simulations. Inelastic contributions change the downstream equilibrium state and allow the flow to transition to the equilibrium state further upstream.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Recent advances and future prospects for Monte Carlo

The history of Monte Carlo methods is closely linked to that of computers: The first known Monte Carlo program was written in 1947 for the ENIAC; a pre-release of the first Fortran compiler was used for Monte Carlo In 1957; Monte Carlo codes were adapted to vector computers in the 1980s, clusters and parallel computers in the 1990s, and teraflop systems in the 2000s. Recent advances include hierarchical parallelism, combining threaded calculations on multicore processors with message-passing among different nodes. With the advances In computmg, Monte Carlo codes have evolved with new capabilities and new ways of use. Production codes such as MCNP, MVP, MONK, TRIPOLI and SCALE are now 20-30 years old (or more) and are very rich in advanced featUres. The former 'method of last resort' has now become the first choice for many applications. Calculations are now routinely performed on office computers, not just on supercomputers. Current research and development efforts are investigating the use of Monte Carlo methods on FPGAs. GPUs, and many-core processors. Other far-reaching research is exploring ways to adapt Monte Carlo methods to future exaflop systems that may have 1M or more concurrent computational processes.

99 GENERAL AND MISCELLANEOUS↗

Air-kerma strength determination of a new directional {sup 103}Pd source

Purpose: A new directional {sup 103}Pd planar source array called a CivaSheet™ has been developed by CivaTech Oncology, Inc., for potential use in low-dose-rate (LDR) brachytherapy treatments. The array consists of multiple individual polymer capsules called CivaDots, containing {sup 103}Pd and a gold shield that attenuates the radiation on one side, thus defining a hot and cold side. This novel source requires new methods to establish a source strength metric. The presence of gold material in such close proximity to the active {sup 103}Pd region causes the source spectrum to be significantly different than the energy spectra of seeds normally used in LDR brachytherapy treatments. In this investigation, the authors perform air-kerma strength (S{sub K}) measurements, develop new correction factors for these measurements based on an experimentally verified energy spectrum, and test the robustness of transferring S{sub K} to a well-type ionization chamber. Methods: S{sub K} measurements were performed with the variable-aperture free-air chamber (VAFAC) at the University of Wisconsin Medical Radiation Research Center. Subsequent measurements were then performed in a well-type ionization chamber. To realize the quantity S{sub K} from a directional source with gold material present, new methods and correction factors were considered. Updated correction factors were calculated using the MCNP 6 Monte Carlo code in order to determine S{sub K} with the presence of gold fluorescent energy lines. In addition to S{sub K} measurements, a low-energy high-purity germanium (HPGe) detector was used to experimentally verify the calculated spectrum, a sodium iodide (NaI) scintillating counter was used to verify the azimuthal and polar anisotropy, and a well-type ionization chamber was used to test the feasibility of disseminating S{sub K} values for a directional source within a cylindrically symmetric measurement volume. Results: The UW VAFAC was successfully used to measure the S{sub K} of four CivaDots with reproducibilities within 0.3%. Monte Carlo methods were used to calculate the UW VAFAC correction factors and the calculated spectrum emitted from a CivaDot was experimentally verified with HPGe detector measurements. The well-type ionization chamber showed minimal variation in response (<1.5%) as a function of source positioning angle, indicating that an American Association of Physicists in Medicine (AAPM) Accredited Dosimetry Calibration Laboratory calibrated well chamber would be a suitable device to transfer an S{sub K}-based calibration to a clinical user. S{sub K} per well-chamber ionization current ratios were consistent among the four dots measured. Additionally, the measurements and predictions of anisotropy show uniform emission within the solid angle of the VAFAC, which demonstrates the robustness of the S{sub K} measurement approach. Conclusions: This characterization of a new {sup 103}Pd directional brachytherapy source helps to establish calibration methods that could ultimately be used in the well-established AAPM Task Group 43 formalism. Monte Carlo methods accurately predict the changes in the energy spectrum caused by the fluorescent x-rays produced in the gold shield.

07 ISOTOPE AND RADIATION SOURCES↗

Advanced Mesh-Enabled Monte Carlo Capability for Multi-Physics Reactor Analysis

This project will accumulate high-precision fluxes throughout reactor geometry on a non-orthogonal grid of cells to support multi-physics coupling, in order to more accurately calculate parameters such as reactivity coefficients and to generate multi-group cross sections. This work will be based upon recent developments to incorporate advanced geometry and mesh capability in a modular Monte Carlo toolkit with computational science technology that is in use in related reactor simulation software development. Coupling this capability with production-scale Monte Carlo radiation transport codes can provide advanced and extensible test-beds for these developments. Continuous energy Monte Carlo methods are generally considered to be the most accurate computational tool for simulating radiation transport in complex geometries, particularly neutron transport in reactors. Nevertheless, there are several limitations for their use in reactor analysis. Most significantly, there is a trade-off between the fidelity of results in phase space, statistical accuracy, and the amount of computer time required for simulation. Consequently, to achieve an acceptable level of statistical convergence in high-fidelity results required for modern coupled multi-physics analysis, the required computer time makes Monte Carlo methods prohibitive for design iterations and detailed whole-core analysis. More subtly, the statistical uncertainty is typically not uniform throughout the domain, and the simulation quality is limited by the regions with the largest statistical uncertainty. In addition, the formulation of neutron scattering laws in continuous energy Monte Carlo methods makes it difficult to calculate adjoint neutron fluxes required to properly determine important reactivity parameters. Finally, most Monte Carlo codes available for reactor analysis have relied on orthogonal hexahedral grids for tallies that do not conform to the geometric boundaries and are thus generally not well-suited to coupling with the unstructured meshes that are used in other physics simulations.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Moment-preserving Monte-Carlo Coulomb collision method for particle codes

Binary-pairing Monte-Carlo methods are widely used in particle-in-cell codes to capture effects of small angle Coulomb collisions. These methods preserve momentum and energy exactly when the simulation particles have equal weights. However, when the interacting particles are of varying weight, these physical conservation laws are only preserved on average. Here, we 1) extend these methods to weighted particles such that the scattering physics is correct on average, and 2) describe a new method for adjusting the particle velocities post scatter to restore exact conservation of momentum and energy. In conclusion, the efficacy of the model is illustrated with various test problems.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Lattice Monte Carlo for quantum Hall states on a torus

The Monte Carlo method is very useful for studying various model states proposed for the fractional quantum Hall systems. In this paper, we introduce a lattice Monte Carlo method based on an exact lattice formalism for quantum Hall problems defined on a torus. This “lattice representation” is applied to study the many body Berry phase of the composite-Fermi liquid phase in a half-filled Landau level. Here, the Monte Carlo result agrees with the exact numerical result found on small systems sizes and is consistent with the prediction from the Dirac fermion low-energy effective theory. Many other aspects of other model states, including the structure factor, Coulomb energy and particle-hole symmetry, are studied and discussed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Energy Gap Closure of Crystalline Molecular Hydrogen with Pressure

Here, we study the gap closure with pressure of crystalline molecular hydrogen. The gaps are obtained from grand-canonical quantum Monte Carlo methods properly extended to quantum and thermal crystals, simulated by coupled electron ion Monte Carlo methods. Nuclear zero point effects cause a large reduction in the gap (~2 eV). Depending on the structure, the fundamental indirect gap closes between 380 and 530 GPa for ideal crystals and 330–380 GPa for quantum crystals. Beyond this pressure the system enters into a bad metal phase where the density of states at the Fermi level increases with pressure up to ~450–500 GPa when the direct gap closes. Our work partially supports the interpretation of recent experiments in high pressure hydrogen.

74 ATOMIC AND MOLECULAR PHYSICS↗

GPU Acceleration of History-Based Multigroup Monte Carlo

Accurate solutions of the radiation transport equation play an important role in the analysis of many nuclear systems. Because there is no need to discretize the problem, Monte Carlo methods offer the most accurate possible solutions to the transport equation. However, significant computational effort is required to reduce the stochastic noise inherent to Monte Carlo methods. Current trends in high performance computing are moving towards vectorized, single instruction multiple data (SIMD), architectures such as Intel Xeon Phis and graphics processing units (GPUs) due to their favorable ratio of performance to power consumption. The challenge of adapting Monte Carlo transport to vectorized computing architectures was first addressed by Brown with an algorithm known as event-based Monte Carlo. In this approach, rather than simulating individual particle histories from birth to death, groups of particles are processed one event at a time. This allows each event batch to perform the same operations in lockstep, enabling use of the vector hardware. Although modern vectorized hardware is more versatile than the early vector machines, reducing so-called thread divergence is nonetheless still an important consideration for algorithm design. Many of the algorithms proposed so far for Monte Carlo transport on advanced architectures have focused on variants of event-based transport. Some evidence, however, suggests that low-level thread divergence, resulting from short-lived branching statements, may not be detrimental to overall performance on GPUs as long as the effect on achievable memory bandwidth is considered. This paper characterizes the performance of a traditional history-based Monte Carlo algorithm on GPUs. We show that with only minor modifications to traditional algorithms, significant performance gains relative to CPUs are possible. (authors)

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Spin decoherence in n-type GaAs: The effectiveness of the third-body rejection method for electron-electron scattering

We study the spin decoherence in n-type bulk GaAs for moderate electronic densities at room temperature using the Ensemble Monte Carlo method. We demonstrate that a technique called “third-body rejection method” devised by B. K. Ridley, J. Phys. C: Solid State Phys. 10, 1589 (1977) can be successfully adapted to Ensemble Monte Carlo method and used to tackle the problem of the electron-electron contribution to spin decoherence in the parameter region under study, where the electron-electron interaction can be reasonably described by a Yukawa potential. This scattering technique is employed in a doping region where one can expect that multiple collisions may play a role in carrier dynamics. By this technique, we are able to calculate spin relaxation times which are in very good agreement with the experimental results found by Oertel et al., Appl. Phys. Lett. 93, 13 (2008). Through this method, we show that the electron-electron scattering is overestimated in Born approximation, in agreement with previous results obtained by C. A. Kukkonen and H. Smith, Phys. Rev. B 8, 4601 (1973).

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Uncertainty Analysis of the NASA Glenn 8x6 Supersonic Wind Tunnel

This paper presents methods and results of a detailed measurement uncertainty analysis that was performed for the 8- by 6-foot Supersonic Wind Tunnel located at the NASA Glenn Research Center. The statistical methods and engineering judgments used to estimate elemental uncertainties are described. The Monte Carlo method of propagating uncertainty was selected to determine the uncertainty of calculated variables of interest. A detailed description of the Monte Carlo method as applied for this analysis is provided. Detailed uncertainty results for the uncertainty in average free stream Mach number as well as other variables of interest are provided. All results are presented as random (variation in observed values about a true value), systematic (potential offset between observed and true value), and total (random and systematic combined) uncertainty. The largest sources contributing to uncertainty are determined and potential improvement opportunities for the facility are investigated.

Error↗

Determination of three-dimensional radiative exchange factors for the Space Shuttle by Monte Carlo

A program was developed to predict radiative exchange factors in three-dimensional configurations with curved, specularly-reflecting surfaces using the Monte Carlo method. It was shown that this can be done efficiently by using the normal Monte Carlo method for closed configurations and/or high surface emissivities, while Energy Partitioning should be used for open configurations and/or low surface emissivities. Comparison with experiments on the Space Shuttle radiator panels showed that the simple model of gray, diffuse emission is sufficient for the prediction of exchange factors between actual (silver-coated teflon) surfaces. For solar-irradiation exchange factors on the Space Shuttle, on the other hand, spectral and directional variations of surface properties must be taken into account.

Modest, M. F.↗

MCCCS-MN

The MCCCS‒MN (Monte Carlo for Complex Chemical Systems‒Minnesota) software is developed by the Siepmann research group at the University of Minnesota. MCCCS‒MN allows for the simulation of multi-component molecular systems in the canonical, isobaric-isothermal (including constant stress for solids), grand-canonical, semi-grand, and Gibbs (NVT, NPT, and more than two simulation boxes) ensembles. It uses the configurational-bias Monte Carlo method to efficiently sample phase space for linear, branched and cyclic chain molecules, the adiabatic nuclear and electronic sampling Monte Carlo method to treat many-body polarization effects, and the aggregation-volume-bias Monte Carlo algorithm to efficiently sample the spatial distribution of associating molecules. MCCCS-MN employs a molecular representation of the system where force fields contain bonded and non-bonded terms. Funding for the development of MCCCS-MN through grants from the National Science Foundation (simulation of fluid phase equilibria and chromatography) and the Department of Energy (simulation of adsorption equilibria) is gratefully acknowledged.

Siepmann, J.Ilja [University of Minnesota - Twin C↗