SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
One complete solution is presented for determining the electromagnetic field of a generalized crossed rectangular waveguide. The method adopted is that of partial regions. Cutoff frequencies of symmetrical crossed waveguides are presented as an example. The results, even for low-order approximations, correspond well with the only experimental results available in the literature.
A general technique for solving a system of rate equations describing the interaction of an electromagnetic field and a molecular system is presented. The method is used to obtain approximate time-dependent solutions for the upper-level population of fluorescent dyes in the presence of a pump field.
A general technique for solving a system of rate equations describing the interaction of an electromagnetic field and a molecular system is presented. The method is used to obtain approximate time-dependent solutions for the upper-level populations of fluorescent dyes in the presence of a pump field.
The Finite Difference Time Domain (FDTD) technique has been applied to a wide variety of electromagnetic analysis problems, including shielding and scattering. However, the method has not been extensively applied to antennas. In this short paper calculations of self and mutual admittances between wire antennas are made using FDTD and compared with results obtained using the Method of Moments. The agreement is quite good, indicating the possibilities for FDTD application to antenna impedance and coupling.
The Finite Difference Time Domain (FDTD) technique was applied to a wide variety of electromagnetic analysis problems, including shielding and scattering. However, the method has not been exclusively applied to antennas. Here, calculations of self and mutual admittances between wire antennas are made using FDTD and compared with results obtained during the method of moments. The agreement is quite good, indicating the possibilities for FDTD application to antenna impedance and coupling.
The present survey of important and novel CFD applications being developed and implemented by U.S. Government contractors gives attention to naval vessel flow-modeling, Army ballistic and rotary wing aerodynamics, and NASA hypersonic vehicle related applications of CFD. CFD-generated knowledge of numerical algorithms, fluid motion, and supercomputer use is being incorporated into such additional areas as computational electromagnetics and acoustics. Attention is presently given to CFD methods' development status in such fields as submarine boundary layers, hypersonic kinetic energy projectile shock structures, helicopter main rotor tip flows, and National Aerospace Plane aerothermodynamics.
Lunar soil can become a source of relatively inexpensive oxygen propellant for vehicles going from low Earth orbit (LEO) to geosynchronous Earth orbit (GEO) and beyond. This lunar oxygen could replace the oxygen propellant that, in current plans for these missions, is launched from the Earth's surface and amounts to approximately 75 percent of the total mass. The reason for considering the use of oxygen produced on the Moon is that the cost for the energy needed to transport things from the lunar surface to LEO is approximately 5 percent the cost from the surface of the Earth to LEO. Electromagnetic launchers, in particular the superconducting quenchgun, provide a method of getting this lunar oxygen off the lunar surface at minimal cost. This cost savings comes from the fact that the superconducting quenchgun gets its launch energy from locally supplied, solar- or nuclear-generated electrical power. We present a preliminary design to show the main features and components of a lunar-based superconducting quenchgun for use in launching 1-ton containers of liquid oxygen, one every 2 hours. At this rate, nearly 4400 tons of liquid oxygen would be launched into low lunar orbit in a year.
The program we are attempting to bring about combines 3 difficult features, in order to demonstrate accuracy of efficiency predictions: (1) Accurate groove metrology methods on surface relief gratings; (2) Rigorous and usable electromagnetic efficiency calculation codes; (3) Accurate efficiency measurements in polarized light The benefit would be an increase in yield for high-performance gratings. Many such applications suffer long lead time or serious performance loss when new gratings are made which do not meet requirements or expectations.
Seismology is a powerful tool for investigating the inner structure and dynamic processes of a planetary body. The interior structure information derived from seismic measurements is complementary to other methods of probing the subsurface (such as gravity and electromagnetics), both in terms of spatial and depth resolution and the relevant types of material properties being sensed. The propagation of seismic waves is sensitive to composition (via density and elastic parameters), temperature (via attenuation) and physical state (solid vs. liquid). In addition, the seismicity (level and distribution in space and time of seismic activity) provides information on the impact flux and tectonic forces currently active within the body. The major satellites of the outer solar system provide obvious targets for seismic investigations. In addition, small bodies, such as asteroids and comets, can also benefit from seismic measurements. We have developed an extremely small, lightweight, low-power seismometer for planetary applications which is ideally suited for use in the outer solar system. This instrument has previously been proposed and selected for use on a comet (on the Rosetta Lander, subsequently deselected for programmatic reasons) and Mars (on the NetLander mission). Additional information is contained in the original extended abstract.
Seismology is one of the most powerful tools for investigating the subsurface structure of a planet. The mechanical structure information derived from seismic measurements is complementary to other methods of probing the subsurface (such as gravity and electromagnetics), both in terms of spatial and depth resolution and the relevant types of material properties being sensed. In the near-surface, the propagation of seismic waves is especially sensitive to density and degree of compaction. In addition, interfaces between layer with contrasting properties can be relatively easily delineated. The subsurface of Mars provides an obvious target for seismic investigations. Searching for the presence of water is among the highest priority goals of the Mars Exploration Program, but there are many other important science questions that could be addressed by a seismic profile of the upper layers of the crust. We have developed an extremely small, lightweight, low-power seismometer for planetary applications which is ideally suited for use on Mars. This instrument has previously been proposed and selected for use on a comet (on the Rosetta Lander, subsequently deselected for programmatic reasons) and Mars (on the NetLander mission, with an emphasis on global structure determination).
Alfven waves are a major mechanism for the transport of electromagnetic energy from the distant part of the magnetosphere to the near-Earth space. This is especially true for the auroral and polar regions of the Earth. However, the mechanisms for their dissipation have remained illusive. One of the mechanisms is the formation of double layers when the current associated with Alfven waves in the inertial regime interact with density cavities, which either are generated nonlinearly by the waves themselves or are a part of the ambient plasma turbulence. Depending on the strength of the cavities, weak and strong double layers could form. Such double layers are transient; their lifetimes depend on that of the cavities. Thus they impulsively accelerate ions and electrons. Another mechanism is the resonant absorption of broadband Alfven- wave noise by the ions at the ion cyclotron frequencies. But this resonant absorption may not be possible for the very low frequency waves, and it may be more suited for electromagnetic ion cyclotron waves. A third mechanism is the excitation of secondary waves by the drifts of electrons and ions in the Alfven wave fields. It is found that under suitable conditions, the relative drifts between different ion species and/or between electrons and ions are large enough to drive lower hybrid waves, which could cause transverse accelerations of ions and parallel accelerations of electrons. This mechanism is being further studied by means of kinetic simulations using 2.5- and 3-D particle-in-cell codes. The ongoing modeling efforts on space weather require quantitative estimates of energy inputs of various kinds, including the electromagnetic energy. Our studies described here contribute to the methods of determining the estimates of the input from ubiquitous Alfven waves.
The Department of Energy, the Stirling Technology Company (STC), and the NASA Glenn Research Center are developing Stirling convertors for Stirling radioisotope generators to provide electrical power for future NASA deep space missions. STC is developing the 55-We technology demonstration convertor (TDC) under contract to the Department of Energy. The Department of Energy recently named Lockheed Martin as the system integration contractor for the Stirling radioisotope generator development project. Lockheed Martin will develop the Stirling radioisotope generator engineering unit and has contract options to develop the qualification unit and the first flight unit. Glenn s role includes an in-house project to provide convertor, component, and materials testing and evaluation in support of the overall power system development. As a part of this work, Glenn has established an in-house Stirling research laboratory for testing, analyzing, and evaluating Stirling machines. STC has built four 55-We convertors for NASA, and these are being tested at Glenn. A cross-sectional view of the 55-We TDC is shown in the figure. Of critical importance to the successful development of the Stirling convertor for space power applications is the development of a lightweight and highly efficient linear alternator. In support, Glenn has been developing finite element analysis and finite element method tools for performing various linear alternator thermal and electromagnetic analyses and evaluating design configurations. A three-dimensional magnetostatic finite element model of STC's 55-We TDC linear alternator was developed to evaluate the demagnetization fields affecting the alternator magnets. Since the actual linear alternator hardware is symmetric to the quarter section about the axis of motion, only a quarter section of the alternator was modeled. The components modeled included the mover laminations, the neodymium-iron-boron magnets, the stator laminations, and the copper coils. The three-dimensional magnetostatic model was then coupled with a circuit simulator model of the alternator load and convertor controller. The coupled model was then used to generate alternator terminal voltage and current predictions. The predicted voltage and current waveforms agreed well with the experimental data, which tended to validate the accuracy of the coupled model. The model was then used to generate predictions of the demagnetization fields acting on the alternator magnets for the alternator under load. The preliminary model predictions indicate that the highest potential for demagnetization is along the inside surface of the uncovered magnets. The demagnetization field for the uncovered magnets when the mover is positioned at the end of a stroke is higher than it is when the mover is at the position of maximum induced voltage or maximum alternator current. Assuming normal load conditions, the model predicted that the onset of demagnetization is most likely to occur for magnet temperatures above 101 C.
EML is an electromagnetic levitation facility planned for the ISS aiming at processing and investigating liquid metals or semiconductors by using electromagnetic levitation technique under microgravity with reduced electromagnetic fields and convection conditions. Its diagnostics and processing methods allow to measure thermophysical properties in the liquid state over an extended temperature range and to investigate solidification phenomena in undercooled melts. The EML project is a common effort of The European Space Agency (ESA) and the German Space Agency DLR. The Microgravity User Support Centre MUSC at Cologne, Germany, has been assigned the responsibility for EML operations. For the EML experiment preparation an extensive scientific ground support program is established at MUSC, providing scientific and technical services in the preparation, performance and evaluation of the experiments. Its final output is the transcription of the scientific goals and requirements into validated facility control parameters for the experiment execution onboard the ISS.
We study the ion acceleration in a mesoscale, spontaneously fragmenting flare current sheet (SFCS) characterized by the presence of a plasmoid cascade. The main subject of our investigation is to determine whether and how plasmoid cascades at intermediate scales in a fragmented current sheet of a solar flare can impact the (preferential) acceleration of specific ions. The time evolution of the SFCS is obtained from high-resolution 2.5D MHD simulations. The ion trajectories (in the background fields resulting from the MHD model), energies, and pitch angles are calculated using a relativistic test-particle code based on the half-acceleration–rotation–half-acceleration method. For light ions, the main acceleration effects of electromagnetic fields within the SFCS are analyzed using the guiding center approximation. We identify regions with the most-efficient ion acceleration within the SFCS, the accelerator efficiency, and spectra of the accelerated ions. The influence of the charge-to-mass ratio on ion behavior is also studied and resulting ion abundances are compared with observational data. The main ion acceleration takes place in the regions with a strong polarization term, which is part of the first-order Fermi acceleration. Because the term is mass dependent, heavier ions undergo preferential acceleration. The ion energy spectra, abundance-enhancement factors, and differential fluxes, obtained from the model, exhibit power-law profiles, in agreement with observed solar energetic particle events. Nonetheless, the obtained slopes for the abundance-enhancement factor do not exactly match the observed data. The computed slopes and profiles are not sensitive to changes in the initial plasma temperature.
This thesis describes the investigation of superconducting multi-mode cavity architecture for superconducting transmon-based quantum computing. The dissertation highlights useful features of radio-frequency cavities used for quantum computing, with a brief discussion on the advantages of superconducting cavities. In the subsequent section, the concept of transmon is introduced and the mechanism of coupling with a cavity is analyzed. Once the foundations of the topic are laid down, the thesis focuses on optimizing a multi-mode superconducting rf cavity design originally developed for high-energy physics applications. Such section articulates in two main parts, the first part concerning the "bare" cavity remake via finite-elements eigenmode simulations using a computer-aided design software called CST Studio Suite®. In the second part, a transmon qubit is physically inserted into the modified cavity to assess the qubit-cavity coupling of the new design. In evaluating said coupling, two distinct analysis methods are used, namely the black-box quantization method and the energy participation ratio method, both implemented using Ansys® High-Frequency Electromagnetic-Field Simulator, or HFSS™. Results from the two evaluations, compared together, show that the optimized design meets the requisites to be used for quantum computing purposes.
Carbon capture and storage (CCS) has emerged as a key solution in the fight against climate change. However, for CCS to succeed, it is crucial to ensure that the sequestered CO2 stays safely trapped underground. The U.S. Department of Energy (DOE) has emphasized the need for advancements in subsurface monitoring, measurement, reporting, and verification. Aside from caprock integrity failure, the other primary failure points usually involve defective cement in the casing annulus of wellbores or plugged and abandoned wells. In addition, many energy producers (e.g., oil and gas, geothermal) and storage and disposal operators (e.g., H2 and water) must deal with the same issue. Poorly placed or degraded cement can create pathways for gas or fluid to escape from casing annuli and in plugged and abandoned or orphan wells, posing environmental risks. Yet, a reliable and cost-effective way to monitor cement and well integrity over multiple decades is still unavailable. Traditional geophysical methods like 4D seismic imaging and surface-based electromagnetic monitoring lack the resolution and accuracy for detecting these types of failures (Vasco et al., 2022; Fawad and Mondol, 2021). Wireline logging is expensive to run continuously and is obtrusive to the operation. While fiber optics can potentially be a solution, its bulkiness can significantly compromise the cement's integrity. To address these challenges, the Advanced Energy Consortium (AEC) at The University of Texas at Austin’s Bureau of Economic Geology (the Bureau) has been pioneering research in subsurface monitoring using its portfolio of distributed autonomous microfabricated sensors for harsh subsurface environments since 2008. A class of these microsensors [System on a Chip (SoC)] can be mixed in cement and permanently placed without compromising the cement column; the sensors would then communicate with each other or a data acquisition (DAQ) master node. Another class of the AEC microsensors can be fully autonomous, with rechargeable micro-batteries capable of exceeding 100°C, flash memory, and, currently, a pressure and temperature sensor. They are designed to circulate in mud, geothermal fluids, U-loops, or pipelines. They can log data into memory and are unobtrusive to operations. Our team has been working on a multi-year DOE-funded project (DE-FE0031856)—supported by $2.95M in federal funding and $0.75M in cost-matching from the AEC—to demonstrate SoC sensor utility for CO2 leakage monitoring in CCS applications. This multi-institutional collaboration developed a novel sensing architecture utilizing radiofrequency (RF) microsensors embedded within the cement sheath. These sensors detect CO2 migration and are interrogated via a Smart Casing Collar (SCC).
NASA researchers were tasked to study the potential for radio signals to excite an aircraft fuel quantity indication system (FQIS) enough to cause arcing, sparking or excessive heating within a fuel tank. Computational techniques were used to determine the threat from external high intensity radiated field (HIRF) transmitters nearby, like shipboard and airborne RADAR systems. Experimental methods were used to determine the threat from Portable Electronic Devices (PEDs) carried aboard by passengers. To support this work, unique electromagnetic coupling measurements were performed on a retired Boeing 747 aircraft, and new test and analysis methods were developed that may be applied to other FQIS designs as well as other aircraft electronic systems.
A method and apparatus for additive manufacturing that includes a material guide for directing a supply of working material. An advancement mechanism comprising one or more pistons, pushers, plungers and/or pressure regulation systems are positioned behind at least a portion of the supply of working material for advancing the working material forward. The working material is heated using an electro-magnetic heating element and the melted or molten working material is deposited from a tip positioned at an end of the material guide.