Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Material design and testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
NASA NTRS2009

Thermal-Structural Analysis of PICA Tiles for Solar Tower Test

Thermal protection materials used in spacecraft heatshields are subjected to severe thermal and mechanical loading environments during re-entry into earth atmosphere. In order to investigate the reliability of PICA tiles in the presence of high thermal gradients as well as mechanical loads, the authors designed and conducted solar-tower tests. This paper presents the design and analysis work for this tests series. Coupled non-linear thermal-mechanical finite element analyses was conducted to estimate in-depth temperature distribution and stress contours for various cases. The first set of analyses performed on isolated PICA tile showed that stresses generated during the tests were below the PICA allowable limit and should not lead to any catastrophic failure during the test. The tests results were consistent with analytical predictions. The temperature distribution and magnitude of the measured strains were also consistent with predicted values. The second test series is designed to test the arrayed PICA tiles with various gap-filler materials. A nonlinear contact method is used to model the complex geometry with various tiles. The analyses for these coupons predict the stress contours in PICA and inside gap fillers. Suitable mechanical loads for this architecture will be predicted, which can be applied during the test to exceed the allowable limits and demonstrate failure modes. Thermocouple and strain-gauge data obtained from the solar tower tests will be used for subsequent analyses and validation of FEM models.

Agrawal, Parul↗
NASA NTRS1979

Aircraft Design Analysis

The helicopter pictured is the twin-turbine S-76, produced by Sikorsky Aircraft division of United Technologies, Stratford, Connecticut. It is the first transport helicopter ever dey n e d purely as a commercial vehicle rather than an adaptation of a military design. Being built in large numbers for customers in 16 countries, the S-76 is intended for offshore oil rig support, executive transportation and general utility service. The craft carries 12 passengers plus a crew of two and has a range of more than 450 miles-yet it weighs less than 10,000 pounds. Significant weight reduction was achieved by use of composite materials, which are generally lighter but stronger than conventional aircraft materials. NASA composite technology played a part in development of the S-76. Under contract with NASA's Langley Research Center, Sikorsky Aircraft designed and flight-tested a helicopter airframe of advanced composite materials.

Source record↗
NASA NTRS1983

Design, fabrication and test of graphite/polymide composite joints and attachments: Summary

The design, analysis and testing performed to develop four types of graphite/polyimide (Gr/PI) bonded and bolted composite joints for lightly loaded control surfaces on advanced space transportation systems that operate at temperatures up to 561K (550 F) are summarized. Material properties and 'small specimen' tests were conducted to establish design data and to evaluate specific design details. 'Static discriminator' tests were conducted on preliminary designs to verify structural adequacy. Scaled up specimens of the final joint designs, representative of production size requirements, were subjected to a series of static and fatigue tests to evaluate joint strength. Effects of environmental conditioning were determined by testing aged (125 hours 589K (600 F)) and thermal cycled (116K to 589K (-250 F to 600 F), 125 times) specimens. It is concluded Gr/PI joints can be designed and fabricated to carry the specified loads. Test results also indicate a possible resin loss or degradation of laminates after exposure to 589K (600 F) for 125 hours.

Cushman, J. B.↗
NASA NTRS2014

An Experimental Study of Launch Vehicle Propellant Tank Fragmentation

In order to better understand launch vehicle abort environments, Bangham Engineering Inc. (BEi) built a test assembly that fails sample materials (steel and aluminum plates of various alloys and thicknesses) under quasi-realistic vehicle failure conditions. Samples are exposed to pressures similar to those expected in vehicle failure scenarios and filmed at high speed to increase understanding of complex fracture mechanics. After failure, the fragments of each test sample are collected, catalogued and reconstructed for further study. Post-test analysis shows that aluminum samples consistently produce fewer fragments than steel samples of similar thickness and at similar failure pressures. Video analysis shows that there are several failure 'patterns' that can be observed for all test samples based on configuration. Fragment velocities are also measured from high speed video data. Sample thickness and material are analyzed for trends in failure pressure. Testing is also done with cryogenic and noncryogenic liquid loading on the samples. It is determined that liquid loading and cryogenic temperatures can decrease material fragmentation for sub-flight thicknesses. A method is developed for capture and collection of fragments that is greater than 97 percent effective in recovering sample mass, addressing the generation of tiny fragments. Currently, samples tested do not match actual launch vehicle propellant tank material thicknesses because of size constraints on test assembly, but test findings are used to inform the design and build of another, larger test assembly with the purpose of testing actual vehicle flight materials that include structural components such as iso-grid and friction stir welds.

Richardson, Erin↗
NASA NTRS1975

EV space suit gloves (passive)

A pair of pressure and thermal insulating overgloves to be used with an Extravehicular (EV) suit assembly was designed, developed, fabricated, and tested. The design features extensive use of Nomex felt materials in lieu of the multiple layer insulation formerly used with the Apollo thermal glove. The glove theoretically satisfies all of the thermal requirements. The presence of the thermal glove does not degrade pressure glove tactility by more than the acceptable 10% value. On the other hand, the thermal glove generally degrades pressure glove mobility by more than the acceptable 10% value, primarily in the area of the fingers. Life cycling tests were completed with minimal problems. The thermal glove/pressure glove ensemble was also tested for comfort; the test subjects found no problems with the thermal glove although they did report difficulties with pressure points on the pressure glove which were independent of the thermal glove.

Fletcher, E. G.↗
NASA NTRS2018

Structural Certification of Human-Rated Inflatable Space Structures

This paper details the results of an initial study to develop a certification plan for human-rated inflatable space structures, including guidelines for qualification testing. Habitable softgoods inflatables are multi-layered shell structures that use high-strength webbing, cordage and broadcloth fabric to carry the skin loads of a variety of volumetric shapes and structural architectures. The primary objectives of this study are to define the key parameters that affect these structures and propose a statistically robust approach to defining safety and knockdown factors based on test and analysis. Current NASA standards for habitable inflatable space structures use a factor of safety of 4, which was inherited from airship design criteria. An updated approach to defining a design factor, taking into account material strength variability, load variability in the article, number of test samples, and damage and degradation effects is specified. Accurate analytical modeling of these structures is hindered by the difficulty of obtaining accurate and consistent material data due to load-history- dependent, nonlinear load versus strain behavior. A building block approach to certification is detailed that uses stochastic modeling and statistical test design and analysis to address the unique challenges these high-strength softgoods structures present. Human-rated inflatable modules are a transformative capability for launching much larger habitable volumes into space than is possible with rigid shell structures. This research aims to provide the framework for certifying these structures for future human space exploration missions.

Jones, Thomas C.↗
NASA NTRS2011

The Design, Fabrication, and Testing of Composite Heat Exchange Coupons

Several heat exchanger (HX) test panels were designed, fabricated and tested at the NASA Glenn Research Center to explore the fabrication and performance of several designs for composite heat exchangers. The development of these light weight, high efficiency air-liquid test panels was attempted using polymer composites and carbon foam materials. The fundamental goal of this effort was to demonstrate the feasibility of the composite HX for various space exploration and thermal management applications including Orion CEV and Altair. The specific objectives of this work were to select optimum materials, designs, and to optimize fabrication procedures. After fabrication, the individual design concept prototypes were tested to determine their thermal performance and to guide the future development of full-size engineering development units (EDU). The overall test results suggested that the panel bonded with pre-cured composite laminates to KFOAM Grade L1 scored above the other designs in terms of ease of manufacture and performance.

Quade, Derek J.↗
NASA NTRSDate not supplied

Improved Breathing Cartridge (IBC)

The Fire Cartridge (FC) is designed to work with the Emergency Mask (EM) to protect the crew by cleaning the inhaled air in a post fire environment. The Improved Breathing Cartridge (IBC) is designed as a next generation FC with the lessons learned from years of building and testing the FC design, as well as novel catalyst materials to improve the performance and robustness of the cartridge. The FC was designed with minimal margin to save on mass, while the IBC was sized to have over 100% excess catalyst to achieve the required conversion, and still reduce the production cost. Kinetic data taken from another project was used to size the catalyst bed from the standard plug flow reactor conversion equation. The cartridge has been 3D printed and will soon be filled with the required levels of media. Testing has not yet been performed to determine final performance.

Fire Response↗
NASA NTRS1982

Design, fabrication and test of graphite/polyimide composite joints and attachments

The design, analysis, and testing performed to develop four types of graphite/polyimide (Gr/PI) bonded and bolted composite joints for lightly loaded control surfaces on advanced space transportation systems that operate at temperatures up to 561 K (550 F) are summarized. Material properties and small specimen tests were conducted to establish design data and to evaluate specific design details. Static discriminator tests were conducted on preliminary designs to verify structural adequacy. Scaled up specimens of the final joint designs, representative of production size requirements, were subjected to a series of static and fatigue tests to evaluate joint strength. Effects of environmental conditioning were determined by testing aged (125 hours at 589 K (600 F)) and thermal cycled (116 K to 589 K (-250 F to 600 F), 125 times) specimens. It is concluded Gr/PI joints can be designed and fabricated to carry the specified loads. Test results also indicate a possible resin loss or degradation of laminates after exposure to 589 K (600 F) for 125 hours.

Cushman, J. B.↗
NASA NTRSDate not supplied

Playing with DIRT: Building the Framework for a Comprehensive In-Situ Soil Materials Testing Database

Long-term, sustainable planetary exploration will require the ability to "live off the land," relying on In-Situ Resource Utilization (ISRU) and In-Situ Construction as core capabilities. Reduction of both risk and launch mass for lunar construction will require evaluating and comparing regolith materials for use as feedstocks suitable for in-situ beneficiation and fabrication of building components. These material assessment capabilities will inform lunar infrastructure design decisions, with co-benefits for terrestrial construction using in-situ materials. Current planetary construction technology development relies on lunar mapping and orbital data, Apollo-era sample analyses, current simulant inventories, and tests conducted using analog site soils. Requirements for lunar infrastructure design decisions and construction systems will be determined based on specific environmental conditions, mission architectures, and the materials available within traverse range of lunar feedstock processing depots. Critical for success is the capability to identify, evaluate and make effective use of a wide range of materials as they are found in-situ on the lunar surface. This paper discusses the development of a digital repository for data on soil and regolith properties, beginning with their structural performance in both cementitious and non-cementitious building material formulations. The Database for In-situ Resource Testing (DIRT) compiles a catalog of raw materials, additives, and formulations, with notations pertaining to material sources and preparation techniques entered via a web-based user interface. Design of consistent data schemas for site-sourced materials evaluation will facilitate linkage with relevant terrestrial and planetary materials databases while enabling guided data input via templates for participation by broader groups of collaborators. Results of these analyses are compiled in a centralized repository to generate insights applicable for regolith resources and landing sites yet to be precisely defined. Collection of thorough records of material characteristics, applications and performance will support innovative construction solutions not only for space infrastructure but for sustainable, resilient design in the terrestrial built environment.

Sarah Joey Seitz↗
NASA NTRS1990

Comparison between design and installed acoustic characteristics of NASA Lewis 9- by 15-foot low-speed wind tunnel acoustic treatment

The test section of the NASA Lewis 9- by 15-Foot Low-Speed Wind Tunnel was acoustically treated to allow the measurement of sound under simulated free-field conditions. The treatment was designed for high sound absorption at frequencies above 250 Hz and for withstanding the environmental conditions in the test section. In order to achieve the design requirements, a fibrous, bulk-absorber material was packed into removable panel sections. Each section was divided into two equal-depth layers packed with material to different bulk densities. The lower density was next to the facing of the treatment. The facing consisted of a perforated plate and screening material layered together. Sample tests for normal-incidence acoustic absorption were also conducted in an impedance tube to provide data to aid in the treatment design. Tests with no airflow, involving the measurement of the absorptive properties of the treatment installed in the 9- by 15-foot wind tunnel test section, combined the use of time-delay spectrometry with a previously established free-field measurement method. This new application of time-delay spectrometry enabled these free-field measurements to be made in nonanechoic conditions. The results showed that the installed acoustic treatment had absorption coefficients greater than 0.95 over the frequency range 250 Hz to 4 kHz. The measurements in the wind tunnel were in good agreement with both the analytical prediction and the impedance tube test data.

Dahl, Milo D.↗
NASA NTRS2009

NASA-STD-6016 Standard Materials and Processes Requirements for Spacecraft

The standards for materials and processes surrounding spacecraft are discussed. Presentation focused on minimum requirements for Materials and Processes (M&P) used in design, fabrication, and testing of flight components for NASA manned, unmanned, robotic, launch vehicle, lander, in-space and surface systems, and spacecraft program/project hardware elements.Included is information on flammability, offgassing, compatibility requirements, and processes; both metallic and non-metallic materials are mentioned.

Hirsch, David B.↗
NASA NTRS1990

An approach for relating the results of quantitative nondestructive evaluation to intrinsic properties of high-performance materials

One of the most difficult problems the manufacturing community has faced during recent years has been to accurately assess the physical state of anisotropic high-performance materials by nondestructive means. In order to advance the design of ultrasonic nondestructive testing systems, a more fundamental understanding of how ultrasonic waves travel and interact within the anisotropic material is needed. The relationship between the ultrasonic and engineering parameters needs to be explored to understand their mutual dependence. One common denominator is provided by the elastic constants. The preparation of specific graphite/epoxy samples to be used in the experimental investigation of the anisotropic properties (through the measurement of the elastic stiffness constants) is discussed. Accurate measurements of these constants will depend upon knowledge of refraction effects as well as the direction of group velocity propagation. The continuing effort for the development of improved visualization techniques for physical parameters is discussed. Group velocity images are presented and discussed. In order to fully understand the relationship between the ultrasonic and the common engineering parameters, the physical interpretation of the linear elastic coefficients (the quantities that relate applied stresses to resulting strains) are discussed. This discussion builds a more intuitional understanding of how the ultrasonic parameters are related to the traditional engineering parameters.

Miller, James G.↗
NASA NTRSDate not supplied

Py MILab: Capturing, Analyzing and Storing Test Data

Integrated Computational Materials Engineering (ICME) has recently received widespread attention due to its promises in reducing dependence on physical testing for engineering design by relying on simulation, reducing both time and cost to market for various applications. ICME however requires validated multiscale material models, which is heavily dependent on available test data with full material and test pedigree, including material processing, test and measurement equipment, raw data collection, and analysis methodology and results. Populating searchable information management systems with such rich data sets is often burdensome for data producers, resulting in a lack of findable data for modelers to validate and verify their models. To overcome these cultural barriers to ICME, NASA has developed of various database-integration toolsets that perform both data management activities within the organization’s best practices with additional functionality that relieves the effort of the data producer and promotes adoption of information management system. One such tool currently under development is Py MILab, an automatic framework for automatic capturing, analysis, maintenance, and storage of material test data. Py MILab uses a modular approach for capturing raw data, analyzing the data, and storing the data in a database, interfaced by neutral file structures, to promote plug-and-play capabilities for various analysis types. TMAnalysis is a Python-based tool that performs automatic data reduction and analysis of uniaxial thermomechanical test data. The TMAnalysis toolset can be implemented within the Analysis module of Py MILab, and thus requires a populated neutral file form the Raw Data Module of Py MILab and outputs a Analysis neutral file compatible with the Database Module of Py MILab. TMAnalysis is able to perform automatic segmentation of multistage tests and perform data analysis and reduction, including determination of point-wise properties in tension, compression, and shear, analysis of stress relaxation tests, creep analysis and zone identification, and combination of these stage types for tests with complex loading histories. The TMAnalysis code is accompanied with a graphical user interface (GUI) that allows users to easily analyze test data in bulk, verify the automatic, consistent analysis performed by the backend code, and edit stage segmentation if necessary before producing the output neutral files, ensuring data is properly analyzed and maintained with full traceability.

Data management↗
NASA NTRS2016

Additive Manufacturing, Design, Testing, and Fabrication: A Full Engineering Experience at JSC

I worked on several projects this term. While most projects involved additive manufacturing, I was also involved with two design projects, two testing projects, and a fabrication project. The primary mentor for these was Richard Hagen. Secondary mentors were Hai Nguyen, Khadijah Shariff, and fabrication training from James Brown. Overall, my experience at JSC has been successful and what I have learned will continue to help me in my engineering education and profession long after I leave. My 3D printing projects ranged from less than a 1 cubic centimeter to about 1 cubic foot and involved several printers using different printing technologies. It was exciting to become familiar with printing technologies such as industrial grade FDM (Fused Deposition Modeling), the relatively new SLA (Stereolithography), and PolyJet. My primary duty with the FDM printers was to model parts that came in from various sources to print effectively and efficiently. Using methods my mentor taught me and the Stratasys Insight software, I was able to minimize imperfections, hasten build time, improve strength for specific forces (tensile, shear, etc...), and reduce likelihood of a print-failure. Also using FDM, I learned how to repair a part after it was printed. This is done by using a special kind of glue that chemically melts the two faces of plastic parts together to form a fused interface. My first goal with SLA technology was to bring the printer back to operational readiness. In becoming familiar with the Pegasus SLA printer, I researched the leveling, laser settings, and different vats to hold liquid material. With this research, I was successfully able to bring the Pegasus back online and have successfully printed multiple sample parts as well as functional parts. My experience with PolyJet technology has been focused on an understanding of the abilities/limits, costs, and the maintenance for daily use. Still upcoming will be experience with using a composite printer that uses FDM technology to print plastic while laying an internal filament of Kevlar or carbon-fiber inside the printed material. It has been incredible being exposed to this range of technologies and I feel very fortunate to be ready for virtually any kind of printing technology I come across in the future. Design work played a part in my internship this term as well. Working with Hai Nguyen, I was able to design a set of testing tips and a test frame for use with an Arcjet. The testing tips will be made of several different materials that will possibly be used in the heat shield of the Orion space craft. These designs included technical drawings that were presented to the fabrication shop. The frame design was created from 80/20 (a popular brand of frame construction equipment) and included an order form with pricing for fabrication. An independent design was also done for the virtual reality lab. This design was to create a hand-controller based on a previous design. This final design was sent directly to a 3D printer without technical drawings. Overall, my design work has given me experience with using 80/20, helped improve my CAD (Computer Aided Design) proficiency, and increased my knowledge of how to set up technical drawings for fabrication. The final role I have played in this internship has been to assist with testing of the inflatable technology materials working Khadijah Shariff. I began the internship assisting with permeability testing with the initial plan to continue the testing independently after training. Unfortunately, the testing apparatus suffered a technical failure and had funding pulled which cancelled that portion of the project. Further testing with inflatable technology continued with tensile testing of various stitching methods. This testing took place over a two-days and concluded successfully. Final testing was to be more tensile testing but of straps used to connect various inflatable sections. Unfortunately, the needed grips for the tensile tests could not be located and put the testing on hold. It is possible this round of testing will still take place by the end of the internship if the grips can be found. Overall, this portion of the internship has helped me become familiar with one kind of permeability test as well as a popular tensile/compression testing machine. Finally, I also had the chance to be trained using a metal lathe for making very small tips for a soldering iron. These tips will be used to melt threaded brass inserts into 3D printed plastic. Working with James Brown, I was able to successfully machine a brass rod down to as little as 0.064 inches plus or minus 0.001 inches. It was very rewarding to learn how to best use the machine and become familiar with a skill that will undoubtedly be used again in the future. I have been told by several professional engineers that learning to use a lathe and mill will be invaluable skills in the field. This knocks 50 percent of that goal off and I look forward to learning the mill at some point in the future. As is apparent with this list of projects, my internship was not focused on a single over-arching goal. Instead, I was able to gain experience in a myriad of very different areas. I feel like my time here was spent bouncing from one project to the next. Though sometimes difficult to switch gears, it was very rewarding to be a part of so much in so little time. My career and education will be positively impacted by what I have learned at JSC. My experience with 3D printing has improved my ability to handle many issues that may come up in the future with multiple different technologies. The design work I took part in, especially creating technical drawings, will help me better present designs to any engineer or shop I will encounter. My testing experience has helped me become familiar with a popular kind of tensile test machine that will likely be similar to the kinds I will encounter in the future. Finally, my experience with fabrication has given me a rare opportunity, as an engineer, to take part in the fabrication of a part. This experience will help me better tailor my future designs for the manufacturing process and has given me an appreciation for detailed/delicate machining work. My experience at JSC has been successful and will continue to assist me for a long time within the engineering field.

Zusack, Steven↗
NASA NTRS2019

Review of Habitable Softgoods Inflatable Design, Analysis, Testing, and Potential Space Applications

Inflatable space structures have the potential to significantly reduce the required launch volume of large crewed pressure vessels for space exploration missions. Mass savings can also be achieved via the use of high specific strength softgoods materials, and the reduced design penalty from launching the structure in a densely packaged state. Inflatable softgoods structures have been investigated since the late 1950's, and several major development programs at NASA and in industry have helped advance the state-of-the-art in this technology area. This paper discusses the design, analysis, structural testing, and potential applications for inflatable softgoods structures. In particular, this paper will discuss the design of the multi-layer softgoods shell (inner layer, bladder, structural restraint layer, micrometeoroid orbital debris protection layers, thermal insulation layers, and atomic oxygen layer (for low earth orbit) and the results of material and module-level testing that has been conducted over the past two decades at NASA. Finally, the current utilization of expandable spacecraft structures is discussed, as well as potential future applications including airlocks and habitats on the Lunar Orbital Platform-Gateway, and the surface of the Moon and Mars.

Valle, Gerard↗
NASA NTRS1994

Gripping System For Mechanical Testing Of Composites

Specimens held without slippage, even at high temperatures. Improved gripping system designed to securely hold ends of specimen of composite material during creep or tensile test. Each grip includes pair of wedges having sharply corrugated gripping surfaces. Wedges held between two plates containing cavities sloped to accommodate wedges. Two such grips (one for each end) holds specimen in furnace connected to tensile test machine for creep measurements.

Mackay, Rebecca A.↗
NASA NTRS1966

Insulated Engine, 100-Pound Thrust

The design and test results of an insulated, 100-pound thrust engine capable of delivering high performance, providing long, steady state and pulse mode endurance, and maintaining a low outside surface temperature of 4000 F, are presented. Included are descriptions of the injector designs and insulation materials investigated, plus a discussion of the thermal analysis and test results. Continuous operation in excess of 29 minutes, and start capability in excess of 4900 pulses, have been demonstrated. To allow the use of available chamber materials and coating systems under insulated conditions, the major challenge to the designer was to define an injector design that would provide gas temperatures and performance of a predetermined value. The solution was the development of an unbalanced, 8-element triplet injector having an unequal fuel distribution within each element, capable of providing a specific impulse in excess of 290 pounds at reduced wall temperatures. The design consists of a columbium chamber and nozzle utilizing a silicide coating, a columbium injector, a composite insulation system of aluminum oxide

Roth, N. R.↗