Characteristics of solar cells at low temperatures.
Solar cell characteristics at low temperatures, noting efficiency increase with decreasing temperature
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Solar cell characteristics at low temperatures, noting efficiency increase with decreasing temperature
Economical, low-temperature chlorinolysis converts sulfur to water-soluble sulfates. Sulfates are removed by washing. Subsequent steps dry coal and remove chlorine. Chlorine and solvents can be reused.
The dominant ions in low-temperature rare gas plasmas can be either molecular ions or atomic ions depending on the discharge regime. Here, the dominant ions in low-temperature argon plasmas are characterized in a wide range of gas pressure (1-800 Torr). The channels for creation of molecular ions include atom assisted association, dissociative recombination, dissociation by atom impact (DAI), and dissociation by electron impact (DEI). The latter two were previously less often considered. It is found that the DEI reaction has a significant impact on the ion fractions, while the effect of the DAI reaction is much less important in the whole investigated gas pressure regime. As the gas pressure increases from 1 to 800 Torr, the atomic ion fraction drops rapidly in conjunction with an increase of the molecular ion fraction. This phenomenon confirms that in low-temperature argon plasmas the dominant ion will be the atomic ion in the low pressure regime but the molecular ion in the high pressure regime. The impact of power density is also investigated in combination with the DEI reaction. The results show that both the DEI reaction and the power density serve to delay the transition trend of the ion fraction, shifting the dominance of molecular ions to a higher pressure.
A theoretical framework for power dissipation in low temperature plasmas in corona equilibrium is developed. The framework is based on fundamental conservation laws and reaction cross sections and is only weakly sensitive to plasma parameters, e.g., electron temperature and density. The theory is applied to low temperature atomic and molecular hydrogen laboratory plasmas for which the plasma heating power dissipation to photon emission, ionization, and chemical potential is calculated. The calculated photon emission is compared to recent experimental results.
Infrared (IR) spectra of the alkyl nitrile ices CH3CN and CH3CH2CN are relevant to the study of the low-temperature chemistry of objects within and beyond the Solar System, but the thermodynamically favored low-temperature crystalline phases of these compounds have not been presented and identified in the planetary-sciences literature. Moreover, there is a large variation in the published IR spectra of these two icy solids, including spectra that are used for the analyses of spacecraft data from the Voyager and Cassini missions. Here the IR spectra of the low-temperature crystalline forms of CH3CN and CH3CH2CN, which are the thermodynamically stable phases at Titan temperatures, are presented for the first time with all samples being made by vapor-phase deposition. Conditions are described for producing these ice phases for both compounds, and new measurements are reported of ice density and refractive index, quantities needed to compute IR absorption coefficients, band strengths, optical constants, and, ultimately, nitrile abundances in extraterrestrial environments. Comparisons are drawn between CH3CN and CH3CH2CN, an earlier prediction on their similar crystallization behaviors is verified, and previous work is examined in light of these new results, including a counter-intuitive observation in which the low-temperature phase of an ice is made by heating a high-temperature phase. Applications and extensions are described.
Infrared (IR) spectra of the alkyl nitrile ices CH3CN and CH3CH2CN are relevant to the study of the low-temperature chemistry of objects within and beyond the Solar System, but the thermodynamically favored low-temperature crystalline phases of these compounds have not been presented and identified in the planetary-sciences literature. Moreover, there is a large variation in the published IR spectra of these two icy solids, including spectra that are used for the analyses of spacecraft data from the Voyager and Cassini missions. Here the IR spectra of the low-temperature crystalline forms of CH3CN and CH3CH2CN, which are the thermodynamically stable phases at Titan temperatures, are presented for the first time with all samples being made by vapor-phase deposition. Conditions are described for producing these ice phases for both compounds, and new measurements are reported of ice density and refractive index, quantities needed to compute IR absorption coefficients, band strengths, optical constants, and, ultimately, nitrile abundances in extraterrestrial environments. Comparisons are drawn between CH3CN and CH3CH2CN, an earlier prediction on their similar crystallization behaviors is verified, and previous work is examined in light of these new results, including a counter-intuitive observation in which the low-temperature phase of an ice is made by heating a high-temperature phase. Applications and extensions are described.
In the present work, a number of additives have been investigated for their effect on the charge characteristics of cells containing low temperature, high ester content electrolytes (1.0 M LiPF6 in ethylene carbonate (EC) + ethyl methyl carbonate (EMC) + methyl propionate (MP) 20:20:60 vol % + X additive). These experimental three-electrode cells are composed of graphite anodes, LiNiCoAlO2 cathodes, and a lithium metal reference electrode. Cells were first subjected to electrochemical characterization at various temperatures, consisting of performing Electrochemical Impedance Spectroscopy (EIS), linear micropolarization and Tafel polarization measurement to determine the kinetic parameters for both the anodes and cathodes. Following electrochemical characterization, the cells were subjected to charging at decreasing temperatures using C/5 rates to 4.10V, with a constant potential C/50 current taper. Analysis of the C/20 discharge following the charge at low temperature revealed either the presence or absence of a high voltage plateau during the initial stages of the discharge. This plateau has been linked to the presence of lithium metal on the anode previously and was used as a measure for the extent of lithium plating in the cell. Differential analysis (dV/dQ) was applied as well to more clearly visualize the position of the high voltage plateau and use the peak position (x-axis) in the dV/dQ plot as a gauge for the amount of plating which took place in the cell on the prior charge. Most additives investigated increased the resistance of the anode and decreased the resistance of the cathode, thereby leading to an overall increase in plating observed at low temperature. One additive, LiFSI, was found to be beneficial during low temperature charging, however studies of electrode kinetics from the cell containing LiFSI did not reveal significant improvements compared to the baseline.
The emission intensities of coumarin 545 solution exhibit a low temperature dependence, with a record-low temperature coefficient of only ~0.025% per °C.
We describe the design and development of the Low Temperature Microgravity Physics Facility, which is intended to provide long duration (4.5 months) low temperature (1.4K) and microgravity conditions for scientists to perform breakthrough investigations on board the International Space Station.
Double-layer capacitors are unique energy storage devices, capable of supporting large current pulses as well as a very high number of charging and discharging cycles. The performance of doublelayer capacitors is highly dependent on the nature of the electrolyte system used. Many applications, including for electric and fuel cell vehicles, back-up diesel generators, wind generator pitch control back-up power systems, environmental and structural distributed sensors, and spacecraft avionics, can potentially benefit from the use of double-layer capacitors with lower equivalent series resistances (ESRs) over wider temperature limits. Higher ESRs result in decreased power output, which is a particular problem at lower temperatures. Commercially available cells are typically rated for operation down to only 40 C. Previous briefs [for example, Low Temperature Supercapacitors (NPO-44386), NASA Tech Briefs, Vol. 32, No. 7 (July 2008), p. 32, and Supercapacitor Electrolyte Solvents With Liquid Range Below 80 C (NPO-44855), NASA Tech Briefs, Vol. 34, No. 1 (January 2010), p. 44] discussed the use of electrolytes that employed low-melting-point co-solvents to depress the freezing point of traditional acetonitrile-based electrolytes. Using these modified electrolyte formulations can extend the low-temperature operational limit of double-layer capacitors beyond that of commercially available cells. This previous work has shown that although the measured capacitance is relatively insensitive to temperature, the ESR can rise rapidly at low temperatures, due to decreased electrolyte conductance within the pores of the high surface- area carbon electrodes. Most of these advanced electrolyte systems featured tetraethylammonium tetrafluoroborate (TEATFB) as the salt. More recent work at JPL indicates the use of the asymmetric quaternary ammonium salt triethylmethylammonium tetrafluoroborate (TEMATFB) or spiro-(l,l')-bipyrrolidium tetrafluoroborate (SBPBF4) in a 1:1 by volume solvent mixture of acetonitrile (AN) and methyl formate (MF) enables double-layer capacitor cells to operate well below -40 C with a relatively low ESR. Typically, a less than twofold increase in ESR is observed at -65 C relative to room-temperature values, when these modified electrolyte blends are used in prototype cells. Double-layer capacitor coin cells filled with these electrolytes have displayed the lowest measured ESR for an organic electrolyte to date at low temperature (based on a wide range of electrolyte screening studies at JPL). The cells featured high-surface-area (approximately equal to 2,500 m/g) carbon electrodes that were 0.50 mm thick and 1.6 cm in diameter, and coated with a thin layer of platinum to reduce cell resistance. A polyethylene separator was used to electrically isolate the electrodes.
The implementation of single-molecule magnet properties in spin crossover materials is sought as a unique source of magnetic multistability at the molecular level. Examples however remain extremely scarce, in part due to the diamagnetic state of most Fe( II ) spin crossover materials at low temperatures. We have studied the complex [Fe(mtz) 6 ](CF 3 SO 3 ) 2 (mtz = 1-methyltetrazole) as a tantalizing candidate of such coexistence, due to its known partial spin crossover and therefore paramagnetic native low temperature phase. The single-crystal structures of [Fe(mtz) 6 ](CF 3 SO 3 ) 2 reported here allow rationalizing its peculiar cooperative spin-crossover behavior. Importantly, the high-spin Fe crystallographic sites at low temperature exhibit a high symmetry with a local trigonal distortion, usually source of magnetic anisotropy. The analysis of equilibrium magnetic properties confirm the presence of a significant magnetic anisotropy at the Fe( II ) high spin sites in the high symmetry low temperature phase. This results in field-induced slow relaxation of their magnetization which is dominated at low temperature by tunneling and direct processes and is strongly enhanced above 3 K by Raman and Orbach processes. Unprecedentedly, these single-molecule magnet properties are observed in the native ground state of a spin crossover material and efficiently and reversibly switched OFF through visible light irradiation.
Poster of low-temperature and co-produced geothermal projects nationwide. This map poster summarizes completed, ongoing and proposed projects for FY14.
This paper describes circuit evolutionary experiments at extreme low temperatures, including the test of all system components at this extreme environment (EE). In addition to hardening-by-process and hardening-by-design, 'hardening-by-reconfiguration ', when applicable, could be used to mitigate drifts, degradation, or damage on electronic devices (chips) in EE, by using re-configurable devices and an adaptive selfreconfiguration of their circuit topology. Conventional circuit design exploits device characteristics within a certain temperature/radiation range; when that is exceeded, the circuit function degrades. On a reconfigurable device, although component parameters change in EE, a new circuit design, suitable for new parameter values, may be mapped into the reconfigurable structure to recover the initial circuit function. This paper demonstrates this technique for circuit evolution and recovery at liquid nitrogen temperatures (-196.6 (deg)C). In addition, preliminary tests are performed to assess the survivability limitations of the evolutionary processor at extreme low temperatures.
Despite the added cost and complexity of operating at sub-Kelvin temperatures, there are many measurement applications where the sensitivity and precision provided by low temperature detectors greatly outweigh any disadvantages. As a result, low temperature detectors are now finding wide application for measurements ranging from cosmology to homeland defense. In this tutorial I will introduce the basic operating principles and fundamental performance limits of several types of low temperature detectors.
The Jet Propulsion Laboratory (JPL) is developing the Low Temperature Microgravity Physics Facility (LTMPF). The LTMPF is a multiple user and multiple flight facility that will provide a long duration low temperature environment for performing state of the art experiments at the International Space Station (ISS). During each mission, two distinct primary experiments will be accommodated. Secondary experiments utilizing the hardware built for the primary experiments will also be accommodated during each mission. Over the past year, much progress has occurred on the LTMPF as the flight hardware has started to be built. Also, many changes have occurred. Last summer, the initial flight of the LTMPF was delayed until early 2008 by a 2-year slip in the delivery of the Japanese Experiment Module (KIBO) Exposed Facility of the ISS, where the LTMPF will be attached when it flies. Finally, the experiments that will fly as part of the first mission have been changed so that one Gravitational and Relativistic experiment and one Low Temperature Condensed Matter experiment will fly on each flight of the LTMPF. Therefore, the experiments that will fly on the initial mission of the LTMPF will be DYNAMX and the Superconducting Microwave Oscillator Experiment (SUMO).
Abstract Methionine side chains are flexible entities which play important roles in defining hydrophobic interfaces. We utilize deuterium static solid‐state NMR to assess rotameric inter‐conversions and other dynamic modes of the methionine in the context of a nine‐residue random‐coil peptide (RC9) with the low‐complexity sequence GGKGMGFGL. The measurements in the temperature range of 313 to 161 K demonstrate that the rotameric interconversions in the hydrated solid powder state persist to temperatures below 200 K. Removal of solvation significantly reduces the rate of the rotameric motions. We employed 2 H NMR line shape analysis, longitudinal and rotation frame relaxation, and chemical exchange saturation transfer methods and found that the combination of multiple techniques creates a significantly more refined model in comparison with a single technique. Further, we compare the most essential features of the dynamics in RC9 to two different methionine‐containing systems, characterized previously. Namely, the M35 of hydrated amyloid‐β 1–40 in the three‐fold symmetric polymorph as well as Fluorenylmethyloxycarbonyl (FMOC)‐methionine amino acid with the bulky hydrophobic group. The comparison suggests that the driving force for the enhanced methionine side chain mobility in RC9 is the thermodynamic factor stemming from distributions of rotameric populations, rather than the increase in the rate constant.
Using the vertical Bridgman method, the single crystal of low temperature phase SrMgF{sub 4} is obtained. The crystal is in a very good optical quality with the size of 10×7×5 mm{sup 3}. Detailed photoemission spectra of the element core levels are determined by a monochromatic AlKa (1486.6 eV) X-ray source. Moreover, the first-principles calculations are performed to investigate the electronic structure of SrMgF{sub 4}. A good agreement between experimental and calculated results is achieved. It is demonstrated that almost all the electronic orbitals are strongly localized and the hybridization with the others is very small, but the Mg–F bonds covalency is relatively stronger than that of Sr–F bonds. - Graphical abstract: Large size of low-temperature phase SrMgF{sub 4} crystal was obtained (right) and its electronic structure was investigated by X-ray photoelectron spectroscopy and first-principles calculation (left). - Highlights: • Large size single crystal of low-temperature phase SrMgF{sub 4} is obtained. • Electronic structure of SrMgF{sub 4} is measured by X-ray photoelectron spectroscopy. • Partial densities of states are determined by first-principles calculation. • Good agreement between experimental and calculated results is achieved. • Strong ionic characteristics of chemical bonds are exhibited in SrMgF{sub 4}.
The Low Temperature Heat Pipe Flight Experiment (HEPP) is a fairly complicated thermal control experiment that was designed to evaluate the performance of two different low temperature ethan heat pipes. A total of 388 days of continuous operation with an axially grooved aluminum transporter heat pipe and an axially grooved stainless steel heat pipe diode was demonstrated before the EPDS batteries lost power. Preliminary postflight tests showed that the heat pipes are still functioning. A summary of the flight data analysis for the heat pipes and the related support systems is presented.