SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Conical antenna reflectors using knitted mesh materials for aluminized film eliminate problem areas in thermal distortion and long term stability when film is subjected to ultraviolet radiation. Meshes may be selected from wide selection of yarns to form mesh membrane.
The porosity and platability of various materials were investigated to determine a suitable substrate for nickel-plated electrodes. Immersion, ultrasonics, and flow-through plating techniques were tried using nonproprietary formulations, and proprietary phosphide and boride baths. Modifications to the selected material include variations in formulation and treatment, carbon loading to increase conductivity, and the incorporation of a grid. Problems to be solved relate to determining conductivities and porosities as a function of amount of nickel plated on the plastics; loading; charge and discharge curves of electrodes at different current densities; cell performance; and long-term degradation of electrodes.
It is pointed out that future space missions, such as those involving spacecraft and structural assemblies to be used in geosynchronous orbits, will require ultralightweight composite structures to achieve maximum payloads. Of equal importance is the requirement to provide designs that are cost-competitive with metal designs. For space structures that must resist buckling, graphite-epoxy materials offer an attractive potential for providing lightweight, low-cost structural components that will meet future space mission requirements. A description is presented of a program which was conducted to evaluate the merits of graphite-epoxy cylindrical shells and to continue the development of a design data base for ultralightweight structures. An objective of the program was to design, fabricate, and test a corrugated graphite-epoxy cylinder 10 ft in diameter and 10 ft long.
A deployable mast concept which meets the weight, size and stability requirements for a feed support structure for offset antennas up to 100 meters in diameter is discussed. A triangulated truss configuration, the use of tapered tubes which exhibit a high strength-to-weight ratio, and low CTE graphite-epoxy material are seen to provide an efficient, lightweight and stable truss suitable for an antenna feed support. A low stowage ratio of 30:1 is achieved through a unique preloaded hinge located at the center of each longeron and an autonomous deployment cage with a drive mechanism. Initial analysis and proof of concept hardware validated the basic mechanism and design assumptions and provided a basis for further investigation. The concept can readily accept variations in member size and thus lends itself to optimization for other potential uses where a stiff, lightweight deployable truss is needed.
Smooth coatings deposited on hard-to-polish substrates. Lightweight mirror, leaning against conventional glass mirror, consists of metallic relective layer on substrate coated with polyester resin. Smooth surface of polyester resin made by covering freshly applied resin with piece of smooth glass coated with release agent.
A Shuttle-compatible systems design based on the core concept of attachable modules for the major vehicle components is proposed. The principal features include a disposable cargo/extra-propellant tank module; a porous, radiative, backscattering drag-brake surface material of thin silica cloth; and a lightweight carbon-composite support structure. The mission payload capability for delivery, retrieval, and combined operations is determined for a broad range of missions including NASA/DOD requirements and extending through cis-lunar space. The effects of finite-rate surface catalysis, negative lift, and multiple atmospheric passes in reducing the aerothermal heating rates are also investigated. In addition, the structural and thermal-protection problems of the drag-brake support apparatus are analyzed and recommendations are proposed for future design refinements.
The SIRTF optics are intended for operation at 20 K (or less); it will be extremely inconvenient, expensive, and time consuming if it becomes necessary to accomplish all of the optical element testing, assembly, and alignment at comparable temperatures. The thermal strain behavior, including potential anisotropies and inhomogeneities, of a mirror substrate between room temperature and 20 K thus becomes a major factor in the selection of the substrate material, structural configuration, and joining methods for lightweight structures. With support from Space Projects, NASA Ames Research Center, an optical figure evaluation of a 0.65-meter, lightweight, fused silica mirror at a low-temperature goal of 20 K is being conducted. The design details of a thermal shroud, provisions for extracting heat from the low-conductivity mirror, and wavefront error sources other than the mirror surface are discussed and preliminary test results presented.
Improved formulation prevents cracks. Low-density, thermally insulating material applied by spraying it onto surface to be protected. Material, called "MSA-2" improved version of similar material called "MSA-1". Useful as sprayed, lightweight insulation to cover large areas in terrestrial applications in which manual attachment too slow or impractical. Formulated to be more flexible and to prevent coats as thick as 1/2 in. from developing stress cracks as they cure.
This report is a presentation reviewing the external tanks which are used to provide the propellants for the space shuttle engines. The design of the external tank, and its lift capability improvements are reviewed. The configuration, materials, and key technologies of the super lightweight tank (SLWT) are also described. Among the key technologies which allow the SLWT project to succeed, are the successful development of an appropriate alloy. The reasons for choosing the alloy, Aluminum-Lithium 2195, and issues involved in welding are reviewed. Tests of the weld procedures, and pictures of the test results are shown. The External Tank Project has successfully made the transition from the LWT design to the SLWT design. The SLWT Provides two thirds of the weight savings required to place the Space Station in a 51.6 Degree Orbit.
A Shuttle-compatible systems design based on the core concept of attachable modules for the major vehicle components is proposed. The principal features include a disposable cargo/extra-propellant tank module; a porous, radiative, back-scattering drag-brake surface material of thin silica cloth; and a lightweight carbon-composite support structure. The mission payload capability for delivery, retrieval, and combined operations is determined for a broad range of missions including NASA/DOD requirements and extending through cislunar space. The effects of finite-rate surface catalysis, negative lift, and multiple atmospheric passes in reducing the aerothermodynamic heating rates are also investigated. In addition, the structural and thermal protection problems of the drag-brake support apparatus are analyzed, and recommendations are proposed for future design refinements.
STRUCTO-FAB, a product of Owens-Corning Fiberglas Corporation, is a lightweight but extremely durable tent-like material made of Fiberglas coated with Teflon. It transmits daylight with a reduced need for artificial lighting. It is an outgrowth of a material formulated by NASA in 1967 as a new space suit fabric. Owens-Corning and DuPont provided the original material, which was the basis for Structo-Fab, a permanent architectural fabric used for shopping malls, sports stadiums, etc.
The Department of Energy, Lockheed Martin (LM), Stirling Technology Company, and NASA Glenn Research Center (GRC) are developing a high-efficiency Stirling Radioisotope Generator (SRG) for potential NASA Space Science missions. The SRG is being developed for multimission use, including providing spacecraft onboard electric power for NASA deep space missions and power for unmanned Mars rovers. NASA GRC is conducting an in- house supporting technology project to assist in developing the Stirling convertor for space qualification and mission implementation. Preparations are underway for a thermalhacuum system demonstration and unattended operation during endurance testing of the 55-We Technology Demonstration Convertors. Heater head life assessment efforts continue, including verification of the heater head brazing and heat treatment schedules and evaluation of any potential regenerator oxidation. Long-term magnet aging tests are continuing to characterize any possible aging in the strength or demagnetization resistance of the permanent magnets used in the linear alternator. Testing of the magnet/lamination epoxy bond for performance and lifetime characteristics is now underway. These efforts are expected to provide key inputs as the system integrator, LM, begins system development of the SRG. GRC is also developing advanced technology for Stirling convertors. Cleveland State University (CSU) is progressing toward a multi-dimensional Stirling computational fluid dynamics code, capable of modeling complete convertors. Validation efforts at both CSU and the University of Minnesota are complementing the code development. New efforts have been started this year on a lightweight convertor, advanced controllers, high-temperature materials, and an end-to-end system dynamics model. Performance and mass improvement goals have been established for second- and third-generation Stirling radioisotope power systems.
Foam; a cellular material, is found all around us. Bone and cork are examples of biological cell materials. Many forms of man-made foam have found practical applications as insulating materials. NASA uses the BX-265 foam insulation material on the external tank (ET) for the Space Shuttle. This is a type of Spray-on Foam Insulation (SOFI), similar to the material used to insulate attics in residential construction. This foam material is a good insulator and is very lightweight, making it suitable for space applications. Breakup of segments of this foam insulation on the shuttle ET impacting the shuttle thermal protection tiles during liftoff is believed to have caused the space shuttle Columbia failure during re-entry. NASA engineers are very interested in understanding the processes that govern the breakup/fracture of this complex material from the shuttle ET. The foam is anisotropic in nature and the required stress and fracture mechanics analysis must include the effects of the direction dependence on material properties. Material testing at NASA MSFC has indicated that the foam can be modeled as a transversely isotropic material. As a first step toward understanding the fracture mechanics of this material, we present a general theoretical and numerical framework for computing stress intensity factors (SIFs), under mixed-mode loading conditions, taking into account the material anisotropy. We present mode I SIFs for middle tension - M(T) - test specimens, using 3D finite element stress analysis (ANSYS) and FRANC3D fracture analysis software, developed by the Cornel1 Fracture Group. Mode I SIF values are presented for a range of foam material orientations. Also, NASA has recorded the failure load for various M(T) specimens. For a linear analysis, the mode I SIF will scale with the far-field load. This allows us to numerically estimate the mode I fracture toughness for this material. The results represent a quantitative basis for evaluating the strength and fracture properties of anisotropic foam insulation material.
This paper describes the design and development of an innovative thermal and humidity control system for future space suits. The system comprises an evaporation cooling and dehumidification garment (ECDG) and a lithium chloride absorber radiator (LCAR). The ECDG absorbs heat and water vapor from inside the suit pressure garment, while the LCAR rejects heat to space without venting water vapor. The ECDG is built from thin, flexible patches with coversheets made of non-porous, water-permeable membranes that -enclose arrays of vapor flow passages. Water vapor from inside the spacesuit diffuses across the water permeable membranes, enters the vapor flow channels, and then flows to the LCAR, thus dehumidifying the internal volume of the space suit pressure garment. Additional water evaporation inside the ECDG provides cooling for sensible heat loads. -The heat released from condensation and absorption in the LCAR is rejected to the environment by thermal radiation. We have assembled lightweight and flexible ECDG pouches from prototypical materials and measured their performance in a series of separate effects tests under well-controlled, prototypical conditions. Sweating hot plate tests at typical space suit pressures show that ECDG pouches can absorb over 60 W/ft of latent heat and 20 W/ft of sensible heat from the pressure garment environment. These results are in good agreement with the predictions of our analysis models.
This research effort explored lightweight structural concepts married with advanced smart materials to achieve a wide variety of benefits in airframe and engine components. Lattice block structures were cast from an aerospace structural titanium alloy Ti-6Al-4V and a NiTi shape memory alloy (SMA), and preliminary properties have been measured. A finite element-based modeling approach that can rapidly and accurately capture the deformation response of lattice architectures was developed. The Ti-6-4 and SMA material behavior was calibrated via experimental tests of ligaments machined from the lattice. Benchmark testing of complete lattice structures verified the main aspects of the model as well as demonstrated the advantages of the lattice structure. Shape memory behavior of a sample machined from a lattice block was also demonstrated.
Consolidated carbon nanotube or graphene yarns and woven sheets are consolidated through the formation of a carbon binder formed from the dehydration of sucrose. The resulting materials, on a macro-scale are lightweight and of a high specific modulus and/or strength. Sucrose is relatively inexpensive and readily available, and the process is therefore cost-effective.
Progress within the fi eld of x-ray astronomy depends on astronomical x-ray observations of ever-increasing quality and speed. Fast and high-resolution x-ray observations over a broad spectral range promise amazing new discoveries. These observations, however, require a spaceborne x-ray telescope of unprecedented imaging power. Of the numerous technological concerns associated with the design and construction of such a telescope, the x-ray focusing optics present a particularly complex and arduous set of challenges. An x-ray optical assembly comprises many thousands of x-ray mirrors, a most critical element. Our group at NASA Goddard Space Flight Center (GSFC) pursues the development of an x-ray mirror manufacturing process capable of meeting the stringent quality, production time, and cost requirements of the next-generation of x-ray telescopes. The manufacturing process employs monocrystalline silicon: a lightweight, stiff, thermally conductive, and readily available material which is free of internal stress; it is a nearly ideal material for a thin mirror substrate. The process involves various traditional optical fabrication techniques adapted to x-ray mirror geometry. Presently, our process is capable of fabricating sub-arcsecond half-power diameter (HPD) resolution mirror pairs (primary and secondary) at a mirror thickness of 0.5 mm and of virtually any x-ray optical design (e.g. Wolter-I, Wolter-Schwarzschild, etc.). The mirror substrate surface quality is comparable to, and sometimes exceeding, that of the mirrors on the Chandra X-ray Observatory. This paper describes the various manufacturing steps involved in the production of x-ray mirror substrates and a present status report.
Electroactive polymers are attractive actuation materials because of their large deformation, flexibility, and lightweight. A CCD camera system was constructed to record the curved shapes of bending during the activation of EAP films and image-processing software was developed to digitize the bending curves. A computer program was developed to solve the invese problem of cantilever EAP beams with tip position limiter. using the developed program and acquired curves without tip position limiter as well as the corresponding tip force, the EAP material properties of voltage-strain sensitivity and Young's modulus were determined.