SEARCH · Engineering Papers

Results for “Jet Surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

All sources NASA NTRS DOE OSTI

NASA NTRS1995

Obliquity Experiments with a Mars General Circulation Model

We have simulated the seasonal variation of the general circulation on Mars for obliquities of 0deg and 60deg. These obliquities represent the minimum and maximum values the planet has experienced during the past 10(exp 7) years (e.g., Laskar and Robutel, 1993, Nature, 361, 608-614). The model we use is the NASA/Ames Mars General Circulation Model (Pollack et al., 1993, J. Geophys. Res. 98, 3149-3181). We vary only the obliquity; all other model parameters are as in Pollack et al. At high obliquity, the model shows dramatic seasonal variations in the polar caps and in the structure and intensity of the circulation. At the solstices the winter cap extends to the equator. Thus, surface temperatures throughout the entire winter hemisphere are fixed at the CO2 frost point. During summer surface temperatures at the poles reach 269K in the north and 295K in the south. The most notable changes to the circulation at solstice compared to our standard runs are a general weakening of the winter westerlies, a Hadley cell of greater latitudinal extent, and the development of very strong, possibly unstable, low-level jets in midlatitudes of the summer hemisphere. Surface stresses associated with these jets are sufficient to raise dust continuously. Thus, dust storms should be frequent features of the high obliquity climate. This result is independent of any desorbed regolith CO2 which would raise mean surface pressures. At zero obliquity the structure of the circulation resembles that of present day equinox conditions modulated by the varying insolation associated with orbital eccentricity. Notable features include equatorial superrotation, asymmetric Hadley cells, and stronger poleward heat fluxes in the northern hemisphere. Since the poles do not receive solar energy at any time of year, permanent caps form which extend to about 70deg in each hemisphere. However, the north permanent cap is growing at a rate 40% faster than the south cap. This is due to the differences in topography, albedo, emissivity, and heat transport in each hemisphere. Thus the zero obliquity climate system appears to be evolving toward a state in which the north cap is the dominant cap.

Harberle, R. M.↗

NASA NTRS2015

Low-Profile Diffuser

The propellant tanks used in liquid rockets require pressurization gases in order to maintain tank pressure while the tanks are being drained during engine operation. The pressurization gas, which is typically much warmer than the relatively cold propellants in the tank, must be introduced into the empty ullage space at the top of the tank. The purpose of the diffuser is to control the flow of the gas into the tank in order to prevent direct impingement of the gas on the liquid surface and/or the tank walls. If the diffuser did not perform those tasks, the warm gas can create excess heat transfer causing an increase in the amount of pressurization mass required. Typical diffusers are long vertical cylinders that create a large exit area in order to minimize gas velocities. However, long vertical cylinders limit the amount of liquid that can be loaded into the tank in order not to have the liquid surface near the diffuser. A design goal for a pressurization diffuser is to create uniform flow in order to prevent jets that can impact the liquid surface and/or tank walls. The purpose of the task was to create a diffuser design that had a lower vertical profile (in order to be able to raise the liquid surface) while still maintaining uniform flow.

Martin, Michael A.↗

NASA NTRS2006

Visualization of a Capsule Entry Vehicle Reaction-Control System (RCS) Thruster

Planar laser-induced fluorescence (PLIF) was used to visualize the reaction control system (RCS) jet flow emanating from the aft-body of an Apollo-geometry capsule test article in the NASA Langley Research Center 31-Inch Mach 10 Air wind tunnel. The RCS jet was oriented normal to the aft surface of the model and had a nominal Mach number of 2.94. The composition of the jet gas by mass was 95% nitrogen (N2) and 5% nitric oxide (NO). The RCS jet flowrate varied between zero and 0.5 standard liters per minute and the angle of attack and tunnel stagnation pressure were also varied. PLIF was used to excite the NO molecules for flow visualization. These flow visualization images were processed to determine the trajectory and to quantify the flapping of the RCS jet. The spatial resolution of the jet trajectory measurement was about 1 mm and the single-shot precision of the measurement was estimated to be 0.02 mm in the far field of the jet plume. The jet flapping, measured by the standard deviation of the jet centerline position was as large as 0.9 mm, while the jet was 1.5-4 mm in diameter (full width at half maximum). Schlieren flow visualization images were obtained for comparison with the PLIF. Surface pressures were also measured and presented. Virtual Diagnostics Interface (VIDI) technology developed at NASA Langley was used to superimpose and visualize the data sets. The measurements demonstrate some of the capabilities of the PLIF method while providing a test case for computational fluid dynamics (CFD) validation.

Danehy, P. M.↗

NASA NTRS1994

Effect of Porosity on Surface Catalytic Efficiency

This paper describes the effect of surface porosity of thermal protection materials on surface catalytic efficiency using test data taken from both arc-jet and side-arm reactor facilities. Relative surface porosity of the samples varied from 6% to 50%. Surface porosity was measured using a flow apparatus and Bernoulli equation. The surface catalytic efficiency of the materials was calculated using aerothermodynamic, and kinetic theories. The catalytic efficiency of the materials are compared at surface temperatures between room temperature and 2500 F. The data are presented in the form of graphs and tables.

Stewart, David A.↗

NASA NTRS1978

Pressure and velocity measurements in a three dimensional wall jet

A flat plate and a curved wall surface, intended to model a wing-flap combination in a high V/STOL configuration, were used to measure pressure and flow velocity in a freely expanding coflowing jet and a three dimensional wall jet. The effects of increasing the velocity ratio of the jet exit plane velocity to the free stream velocity were investigated. Velocity measurements were made using a two color laser Doppler velocimeter with a phase-locked loop processor. Fluctuating pressures were monitored with condenser-type microphones. Quantities measured include the width of the mixing region, the mean velocity field, turbulent intensities, and time scales. Wall and static pressure-velocity correlations and coherences are presented.

Catalano, G. D.↗

NASA NTRS1995

Design and Testing of an Automated System using Thermochromatic Liquid Crystals to Determine Local Heat Transfer Coefficients for an Impinging Jet

Using thermochromatic liquid crystal to measure surface temperature, an automated transient method with time-varying free-stream temperature is developed to determine local heat transfer coefficients. By allowing the free-stream temperature to vary with time, the need for complicated mechanical components to achieve a step temperature change is eliminated, and by using the thermochromatic liquid crystals as temperature indicators, the labor intensive task of installing many thermocouples is omitted. Bias associated with human perception of the transition of the thermochromatic liquid crystal is eliminated by using a high speed digital camera and a computer. The method is validated by comparisons with results obtained by the steady-state method for a circular Jet impinging on a flat plate. Several factors affecting the accuracy of the method are evaluated.

Tan, Benjamin↗

NASA NTRS1979

Wing aerodynamic loading caused by jet-induced lift associated with STOL-OTW configurations

Surface pressure distributions were obtained with model-scale STOL-OTW configurations using various nozzles designed to promote flow attachment to the wing/flap surface. The nozzle configurations included slot-types and both circular and slot nozzles with external flow deflectors. The wing aerodynamic loading caused by the jet-induced lift is presented in conventional terms of delta p/q as a function of chordwise surface distance in the nozzle centerline plane as well as outboard of the nozzle centerline. Nozzle roof/deflector angle, chordwise location of the nozzle, wing size, and flap deflection angle are included in the geometric variables affecting the wing loading.

Vonglahn, U.↗

NASA NTRS1979

Wing aerodynamic loading caused by jet-induced lift associated with STOL-OTW configurations

Surface pressure distributions were obtained with model-scale STOL-OTW configurations using various nozzles designed to promote flow attachment to the wing-flap surface. The nozzle configurations included slot-types and both circular and slot nozzles with external flow deflectors. The wing aerodynamic loading caused by the jet-induced lift is presented in conventional terms of delta p/q as a function of chordwise surface distance in the nozzle centerline plane as well as outboard of the nozzle centerline. Included in the geometric variables affecting the wing loading are nozzle roof/deflector angle, chordwise location of the nozzle, wing size, and flap deflection angle.

Von Glahn, U.↗

NASA NTRSDate not supplied

Flow Visualization for Plume-Surface Interaction at Martian-Relevant Lander Environments

This paper describes a jet impingement experiment performed in a large-scale vacuum chamber at Martian-relevant ambient pressure conditions, with the motivation of studying plume-surface interaction (PSI) caused by the exhaust plume of a lander interacting with the planetary surface. Flow visualization of an inert supersonic jet was performed using planar laser-induced fluorescence (PLIF), which is a molecular-based, two-dimensional measurement technique. Representative instantaneous and time-averaged visualizations of the impinging jet at two different nozzle flow conditions corresponding to the underexpanded and overexpanded jet regimes are presented for up to six different dimensionless altitudes h/De. The time-averaged measured spatial distribution of impingement pressures at these conditions is also reported. The PLIF visualizations appear to be critical towards explaining unexpected behavior in the impingement pressure, such as a higher impingement pressure for the underexpanded condition at h/De = 10, compared to a lower altitude of h/De = 8. This behavior can be attributed to differences in the stagnation shock structure observed in the PLIF images. The PLIF images also reveal significant flow separation at the nozzle exit for the overexpanded jet conditions. Further analysis of the test data as well as combined flow visualization and surface diagnostics for future ground tests will help inform engineering designs for landings on the Martian surface while mitigating PSI risks.

PLIF↗

NASA NTRSDate not supplied

Flow Visualization for Plume-Surface Interaction at Martian-Relevant Lander Environments

PLIF↗

NASA NTRS1973

Impinging jet separators for liquid metal magnetohydrodynamic power cycles

In many liquid metal MHD power, cycles, it is necessary to separate the phases of a high-speed liquid-gas flow. The usual method is to impinge the jet at a glancing angle against a solid surface. These surface separators achieve good separation of the two phases at a cost of a large velocity loss due to friction at the separator surface. This report deals with attempts to greatly reduce the friction loss by impinging two jets against each other. In the crude impinging jet separators tested to date, friction losses were greatly reduced, but the separation of the two phases was found to be much poorer than that achievable with surface separators. Analyses are presented which show many lines of attack (mainly changes in separator geometry) which should yield much better separation for impinging jet separators).

Bogdanoff, D. W.↗

NASA NTRS1989

Morphology and compositional differentiation of the surface of comets

The spacecraft missions to Comet Halley gave us the first detailed view of a comet nucleus. What was suspected before, that the nucleus surface was heterogeneous, was confirmed. The Halley Multicolor Camera aboard Giotto recorded jet-like dust features emanating from active regions covering approximately 15 percent of the surface that were responsible for emitting most of the dust and gas. An intensity gradient across the nucleus originating at the active areas and falling off to the darker, inactive region on the night side is caused by small particles that are more easily entrained by surface winds than larger particles that tend to remain in the jets. Data from the PIA (Giotto) and PUMA (Vega 1,2) instruments indicate that the smallest dust particles are enriched with organics (CHON particles). Some of this fine dust gravitationally settles creating a thin surface layer rich in organics. Particularly strong dust jets may cause wind-blown surface structures over inactive areas, such as, leeward dust accumulation behind hills. At close heliocentric distances the fine dust may be sintered on the surface.

Huebner, W. F.↗

NASA NTRS1991

Enhancement of the no-vent fill process

This paper presents an analytical and experimental evaluation of an enhanced techniques for no-vent fill. The method entails injecting liquid through the top of the receiver vessel, thereby increasing surface area and agitation of the ullage/liquid interface. Both of these factors promote condensation induced ullage collapse, and reduce compressive impedance to the incoming liquid. The enhanced process was analyzed by modifying the surface area algorithm of an existing tank thermodynamic code to model a downward-pointing, conical jet impringing on a steadily rising liquid surface. Transient pressure and temperature measurements from several tests with Freon-114 were input into the revised model to calculate condensation rate as a function of fill level. By expressing these rates in dimensionless form (i.e., in terms of Stanton number and Prandtl number), an empirical correlation similar to the submerged jet model of Brown and Sonin (1989) was derived. This provided a basis for developing an expression which relates top fill to bottom fill performance.

Vaughan, David A.↗

NASA NTRS2014

Modeling and Prediction of the Noise from Non-Axisymmetric Jets

The new source model was combined with the original sound propagation model developed for rectangular jets to produce a new version of the rectangular jet noise prediction code. This code was validated using a set of rectangular nozzles whose geometries were specified by NASA. Nozzles of aspect ratios two, four and eight were studied at jet exit Mach numbers of 0.5, 0.7 and 0.9, for a total of nine cases. Reynolds-averaged Navier-Stokes solutions for these jets were provided to the contactor for use as input to the code. Quantitative comparisons of the predicted azimuthal and polar directivity of the acoustic spectrum were made with experimental data provided by NASA. The results of these comparisons, along with a documentation of the propagation and source models, were reported in a journal article publication (Ref. 4). The complete set of computer codes and computational modules that make up the prediction scheme, along with a user's guide describing their use and example test cases, was provided to NASA as a deliverable of this task. The use of conformal mapping, along with simplified modeling of the mean flow field, for noise propagation modeling was explored for other nozzle geometries, to support the task milestone of developing methods which are applicable to other geometries and flow conditions of interest to NASA. A model to represent twin round jets using this approach was formulated and implemented. A general approach to solving the equations governing sound propagation in a locally parallel nonaxisymmetric jet was developed and implemented, in aid of the tasks and milestones charged with selecting more exact numerical methods for modeling sound propagation, and developing methods that have application to other nozzle geometries. The method is based on expansion of both the mean-flowdependent coefficients in the governing equation and the Green's function in series of orthogonal functions. The method was coded and tested on two analytically prescribed mean flows which were meant to represent noise reduction concepts being considered by NASA. Testing (Ref. 5) showed that the method was feasible for the types of mean flows of interest in jet noise applications. Subsequently, this method was further developed to allow use of mean flow profiles obtained from a Reynolds-averaged Navier-Stokes (RANS) solution of the flow. Preliminary testing of the generalized code was among the last tasks completed under this contract. The stringent noise-reduction goals of NASA's Fundamental Aeronautics Program suggest that, in addition to potentially complex exhaust nozzle geometries, next generation aircraft will also involve tighter integration of the engine with the airframe. Therefore, noise generated and propagated by jet flows in the vicinity of solid surfaces is expected to be quite significant, and reduced-order noise prediction tools will be needed that can deal with such geometries. One important source of noise is that generated by the interaction of a turbulent jet with the edge of a solid surface (edge noise). Such noise is generated, for example, by the passing of the engine exhaust over a shielding surface, such as a wing. Work under this task supported an effort to develop a RANS-based prediction code for edge noise based on an extension of the classical Rapid Distortion Theory (RDT) to transversely sheared base flows (Refs. 6 and 7). The RDT-based theoretical analysis was applied to the generic problem of a turbulent jet interacting with the trailing edge of a flat plate. A code was written to evaluate the formula derived for the spectrum of the noise produced by this interaction and results were compared with data taken at NASA Glenn for a variety of jet/plate configurations and flow conditions (Ref. 8). A longer-term goal of this task was to work toward the development of a high-fidelity model of sound propagation in spatially developing non-axisymmetric jets using direct numerical methods for solving the relevant equations. Working with NASA Glenn Acoustics Branch personnel, numerical methods and boundary conditions appropriate for use in a high-resolution calculation of the full equations governing sound propagation in a steady base flow were identified. Computer codes were then written (by NASA) and tested (by OAI) for an increasingly complex set of flow conditions to validate the methods. The NASA-supplied codes were ported to the High-End Computing resources of the NASA Advanced Supercomputing facility for testing and validation against analytical (where possible) and independent numerical solutions. The cases which were completed during the course of this contract were solutions of the two-dimensional linearized Euler equations with no mean flow, a uniform mean flow and a nonuniform mean flow representative of a parallel flow jet.

Leib, Stewart J.↗

NASA NTRS1997

Experimental Investigation of Jet Impingement Heat Transfer Using Thermochromic Liquid Crystals

Jet impingement cooling of a hypersonic airfoil leading edge is experimentally investigated using thermochromic liquid crystals (TLCS) to measure surface temperature. The experiment uses computer data acquisition with digital imaging of the TLCs to determine heat transfer coefficients during a transient experiment. The data reduction relies on analysis of a coupled transient conduction - convection heat transfer problem that characterizes the experiment. The recovery temperature of the jet is accounted for by running two experiments with different heating rates, thereby generating a second equation that is used to solve for the recovery temperature. The resulting solution requires a complicated numerical iteration that is handled by a computer. Because the computational data reduction method is complex, special attention is paid to error assessment. The error analysis considers random and systematic errors generated by the instrumentation along with errors generated by the approximate nature of the numerical methods. Results of the error analysis show that the experimentally determined heat transfer coefficients are accurate to within 15%. The error analysis also shows that the recovery temperature data may be in error by more than 50%. The results show that the recovery temperature data is only reliable when the recovery temperature of the jet is greater than 5 C, i.e. the jet velocity is in excess of 100 m/s. Parameters that were investigated include nozzle width, distance from the nozzle exit to the airfoil surface, and jet velocity. Heat transfer data is presented in graphical and tabular forms. An engineering analysis of hypersonic airfoil leading edge cooling is performed using the results from these experiments. Several suggestions for the improvement of the experimental technique are discussed.

Dempsey, Brian Paul↗

NASA NTRS1960

An Experimental Investigation and Correlation of the Heat Reduction to Nonporous Surfaces Behind a Porous Leading Edge Through Which Coolant is Ejected

A configuration of a wing segment having constant chord thickness, 0 deg. sweep, a porous steel semicircular leading edge, and solid Inconel surfaces was tested in a Mach number 2.0 ethlyene-heated high-temperature air jet. Measurements were made of the wing surface temperatures at chordwise stations for several rates of helium flow through the porous leading edge. The investigation was conducted at stagnation temperatures ranging from 500 F to 2,400 F, at Reynolds numbers per foot ranging from 0.3 x 10(exp 7) to 1.2 x 10(exp 7), and at angles of attack of 0, +/- 5, and +/- 15 deg. The results indicated that the reduction of wing surface temperatures with respect to their values for no coolant flow, depended on the helium coolant flow rates and the distance behind the area of injection. The results were correlated in terms of the wall cooling parameter and the coolant flow-rate parameter, where the nondimensional flow rate was referenced to the cooled area up to the downstream position. For the same coolant flow rate, lower surface temperatures are achieved with a porous-wall cooling system. However, since flow-rate requirements decrease with increasing allowable surface temperatures, the higher allowable wall temperatures of the solid wall as compared to the structurally weaker porous wall- sharply reduce the flow-rate requirements of a downstream cooling system. Thus, for certain flight conditions it is possible to compensate for the lower efficiency of the downstream or solid-wall cooling system. For example, a downstream cooling system using solid walls that must be maintained at 1,800 F would require less coolant for Mach numbers up to 5.5 than would a porous-wall cooling system for which the walls must be maintained at temperatures less than or equal to 9000 F.

Witte, William G.↗

NASA NTRS1998

Radar Backscatter Across the Gulf Stream Sea Surface Temperature Front

Ocean backscatter signatures were measured by the Jet Propulsion Laboratory airborne NUSCAT K(sub u)-band scatterometer across the Gulf Stream sea surface temperature front. The measurements were made during the Surface Wave Dynamics Experiment (SWADE) off the coast of Virginia and Maryland in the winter of 1991.

Ocean Backscatter Temperature front Gulf Stream↗

NASA NTRS2008

Using Pressure- and Temperature-Sensitive Paint for Global Surface Pressure and Temperature Measurements on the Aft-Body of a Capsule Reentry Vehicle

Pressure Sensitive Paint (PSP) and Temperature Sensitive Paint (TSP) were used to visualize and quantify the surface interactions of reaction control system (RCS) jets on the aft body of capsule reentry vehicle shapes. The first model tested was an Apollo-like configuration and was used to focus primarily on the effects of the forward facing roll and yaw jets. The second model tested was an early Orion Crew Module configuration blowing only out of its forward-most yaw jet, which was expected to have the most intense aerodynamic heating augmentation on the model surface. This paper will present the results from the experiments, which show that with proper system design, both PSP and TSP are effective tools for studying these types of interaction in hypersonic testing environments.

Watkins, A. Neal↗