Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “JUNCTION DIODE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

Enhanced emission from mid-infrared AlInSb light-emitting diodes with p-type contact grid geometry

We report on the impact of lateral current spreading on light emission from aluminium indium antimonide (AlInSb) mid-infrared p-i-n light-emitting diodes (LEDs) grown by molecular beam epitaxy on a GaAs substrate. Due to the high effective mass of holes in Al{sub x}In{sub 1−x}Sb, the resistivity of p-type material determines the 3-D distribution of current flow in the devices. This work shows that maximum light emission, as measured by electroluminescence, and 3-times wall-plug efficiency improvement were obtained at room temperature from devices with a p-type contact grid geometry with a spacing of twice the current spreading length in the p-type material, which was measured by spatially resolved photocurrent. The LED with the optimal contact geometry exhibits improved performance at high injection current levels thanks to the more uniform carrier distribution across the device area.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Optical properties of p–i–n structures based on amorphous hydrogenated silicon with silicon nanocrystals formed via nanosecond laser annealing

Silicon nanocrystals are formed in the i layers of p–i–n structures based on a-Si:H using pulsed laser annealing. An excimer XeCl laser with a wavelength of 308 nm and a pulse duration of 15 ns is used. The laser fluence is varied from 100 (below the melting threshold) to 250 mJ/cm{sup 2} (above the threshold). The nanocrystal sizes are estimated by analyzing Raman spectra using the phonon confinement model. The average is from 2.5 to 3.5 nm, depending on the laser-annealing parameters. Current–voltage measurements show that the fabricated p–i–n structures possess diode characteristics. An electroluminescence signal in the infrared (IR) range is detected for the p–i–n structures with Si nanocrystals; the peak position (0.9–1 eV) varies with the laser-annealing parameters. Radiative transitions are presumably related to the nanocrystal–amorphous-matrix interface states. The proposed approach can be used to produce light-emitting diodes on non-refractory substrates.

36 MATERIALS SCIENCE↗

Synthesis and Characterization of Superconductor Diodes

In the era of modern computing, quantum bits (or qubits) are extensively researched due to their ability to perform computations exponentially faster than classical computers. One promising method for synthesizing qubits on a macroscopic scale is through superconductor diodes (SDs). Unfortunately, SDs are currently limited by their dependence on extremely low temperatures (T ≈ 0K), which restricts their practical usability at larger scales. To address this limitation, researchers are exploring new materials and methods to identify superconductors with higher critical temperatures. My research at the Lawrence Livermore National Laboratory (LLNL) focuses on synthesizing and characterizing superconductor diodes to determine their efficiency for quantum computing applications. Bismuth thin films were synthesized with magnetron sputtering with separate thicknesses which provides information on methods to alter their resistivity. Bismuth was characterized as the topological insulator used in the diode, and its resistivity was measured using a standard four-point probe technique with 1 mA current. Bismuth (99.99% pure) was then purified in a tubular furnace at 400C to use within a Josephson junction as a topological insulator. Niobium and Tantalum Josephson junctions were then synthesized, and they were characterized using a lock-in amplifier four-point probe technique. Materials such as niobium and tantalum are used in high-entropy alloy research, which is a relatively new class of material that has little research within the superconductor diode community, yet the current research shows promise. We anticipate that testing high-entropy superconductors will reveal crucial factors, potentially leading to the development of high-temperature superconductors in the future.

36 MATERIALS SCIENCE↗

Increased magnetic damping of a single domain wall and adjacent magnetic domains detected by spin torque diode in a nanostripe

Spin torque resonance has been used to simultaneously probe the dynamics of a magnetic domain wall and of magnetic domains in a nanostripe magnetic tunnel junction. Due to the large associated resistance variations, we are able to analyze quantitatively the resonant properties of these single nanoscale magnetic objects. In particular, we find that the magnetic damping of both the domains and the domain wall is doubled compared to the damping value of the host magnetic layer. We estimate the contributions to the damping arising from the dipolar couplings between the different layers in the junction and from the intralayer spin pumping effect, and find that they cannot explain the large damping enhancement that we observe. We conclude that the measured increased damping is intrinsic to large amplitudes excitations of spatially localized modes or solitons such as vibrating or propagating domain walls.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Comparison of the properties of AlGaInN light-emitting diode chips of vertical and flip-chip design using silicon as the a submount

Vertical and flip-chip light-emitting diode (LED) chips are compared from the viewpoint of the behavior of current spreading in the active region and the distribution of local temperatures and thermal resistances of chips. AlGaInN LED chips of vertical design are fabricated using Si as a submount and LED flipchips were fabricated with the removal of a sapphire substrate. The latter are also mounted on a Si submount. The active regions of both chips are identical and are about 1 mm{sup 2} in size. It is shown that both the emittance of the crystal surface in the visible range and the distribution of local temperatures estimated from radiation in the infrared region are more uniform in crystals of vertical design. Heat removal from flip-chips is insufficient in regions of the n contact, which do not possess good thermal contact with the submount. As a result, the total thermal resistances between the p-n junction and the submount both for the vertical chips and for flip-chips are approximately 1 K/W. The total area of the flip-chips exceeds that of the vertical design chips by a factor of 1.4.

36 MATERIALS SCIENCE↗

SU-F-T-239: Evaluation of Plastic Scintillator Light Output for Various Lead Doping Concentrations: Towards LET Detection

Purpose: This work seeks to develop a beam quality meter using multiple differently doped plastic scintillators that are thus intrinsically beam-quality dependent. Plastic scintillators spontaneously emit visible light upon irradiation; the amount of light produced is dependent on stopping power (closely related to LET) according to Birks’ law. Doping plastic scintillators can be used to tune their sensitivity to specific LET ranges. Methods: GEANT4.10.1 Monte Carlo (MC) was used to evaluate the response of various scintillator dopant combinations. MC radiation transport and scintillator light response were validated against previously published literature. Current work involves evaluating detector response experimentally; to that end, a detector prototype with interchangeable scintillator housing was constructed. Measurement set-up guides light emitted by the scintillator to a photomultiplier tube via a glass taper junction coupled to an optical fiber. The resulting signal is measured by an electrometer, and normalized to dose readout from a diode. Measurements have been done using clinical electron and orthovoltage beams. MC response (simulated scintillator light normalized to dose scored inside the scintillating volume) was evaluated for four different LET radiations for an undoped and 1%Pb doped scintillator (σ=0.85%). Simulated incident electrons included: 0.05, 0.1, 0.2, 6, 12, and 18 MeV; these energies correspond to a range of stopping power (related to LET) values ranging from 1.824 to 11.09 MeVcm{sup 2}g{sup −1} (SCOL from NIST-ESTAR). Results: Initial MC results show a distinct divergence in scintillator response as LET increases. The response for undoped plastic scintillator indicated a 35.0% increase in signal when going from 18 MeV (low LET) to 0.05 MeV (high LET) while 1%-Pb doped scintillator indicated a 100.9% increase. Conclusion: After validating MC against measurement, simulations will be used to test various concentrations (2%, 4%, 6%) of different high-Z material dopants (W, Mo) to optimize the scintillator types for the beam quality meter. NSERC Discovery Grant RGPIN-435608.

60 APPLIED LIFE SCIENCES↗

Electrical power generation from moderate-temperature radiative thermal sources

Moderate-temperature thermal sources (100° to 400°C) which radiate waste heat are often the by-product of mechanical work, chemical or nuclear reactions, or information processing. We demonstrate conversion of thermal radiation into electrical power using a bipolar grating-coupled complementary metal-oxide-silicon (CMOS) tunnel diode. A two-step photon-assisted tunneling charge pumping mechanism results in separation of charge carriers in pn-junction wells leading to a large open-circuit voltage developed across a load. Electrical power generation from a broadband blackbody thermal source has been experimentally demonstrated with converted power densities of 27 to 61 microwatts per square centimeter for thermal sources between 250° and 400°C. Scalable, efficient conversion of radiated waste heat into electrical power can be used to reduce energy consumption or to power electronics and sensors.

30 DIRECT ENERGY CONVERSION↗

Studies of silicon PN junction solar cells

Silicon pn junction solar cells made with low-resistivity substrates show poorer performance than traditional theory predicts. The purpose of this research was to identify and characterize the physical mechanisms responsible for the discrepancy. Attention was concentrated on the open circuit voltage in shallow junction cells of 0.1 ohm-cm substrate resistivity. A number of possible mechanisms that can occur in silicon devices were considered. Two mechanisms which are likely to be of main importance in explaining the observed low values of open-circuit voltage were found: (1) recombination losses associated with defects introduced during junction formation, and (2) inhomogeneity of defects and impurities across the area of the cell. To explore these theoretical anticipations, various diode test structures were designed and fabricated and measurement configurations for characterizing the defect properties and the areal inhomogeneity were constructed.

Lindholm, F. A.↗

Electrical properties of multi p-n junction devices

The electrical properties of multi p-n junction devices are analyzed. It is found that this type of device possesses bistable characteristics similar to that of a Shockley diode and thus provides an alternative realization of devices for switching applications. The inherently greater current gains involved in the operations of such a device yield in principle higher breakover voltages and higher holding currents. Furthermore, the incorporation of heterostructures in this device introduces a new degree of freedom in tailoring their switching characteristics. Multi p-n heterojunction devices operating as SCR lasers were fabricated, and the experimental results are presented.

Katz, J.↗

Charge carrier extraction and recombination effects in GaInAs/GaAsP multi-quantum well solar cells

The carrier extraction and transport mechanisms as well as the relative contributions of radiative and non-radiative recombination processes are investigated in high-quality strain-balanced GaInAs/GaAsP multi-quantum well solar cells recently implemented in record efficiency multijunction solar cells. A comprehensive suite of complementary characterization techniques including temperature- and suns-dependent photoluminescence and photovoltaic measurements are employed to analyze thermal escape and tunneling rates, which demonstrate the need to move beyond simple drift-diffusion models of p–n junctions. This study examines the processes that best characterize the operation of these devices across varying temperatures using a simple two-diode model, incorporating multiple transport protocols, and provides insights into the performance-limiting processes and pathways for their optimization.

14 SOLAR ENERGY↗

Electrical characterization of Au/quercetin/n-Si heterojunction diode and optical analysis of quercetin thin film

Quercetin (3,5,7,3’,4’-pentahydroxyflavone, QE), one of the most widely distributed flavonoids in fruits and vegetables, has been reported to possess a wide variety of biological effects, including anti-oxidative, anti-inflammatory, anti-apoptosis, hepatoprotective, renoprotective and neuroprotective effects. In this study organic-inorganic junctions were fabricated by forming quercetin complex thin film using spin coating technique on n-Si and evaporating Au metal on the film. Optical properties of quercetin thin film were studied with the help of spectrophotometer. The current-voltage (I-V) characteristic of Au/quercetin/n-Si heterojunction diode was investigated at room temperature in dark. Some basic parameters of the diode such as ideality factor, rectification ratio, barrier height, series resistance and shunt resistance were calculated using dark current-voltage measurement. It was also seen that the device had good sensitivity to the light under 40-100 mW/cm{sup 2} illumination conditions.

60 APPLIED LIFE SCIENCES↗

Plasmon device design: Conversion from surface to junction plasmons with grating-couplers

Scaling calculations and numerical studies are used to show that grating couplers provide effective energy transfer between surface plasmons and slower modes localized in the tunnel diodes. Within first order perturbation theory in grating amplitude, 90% efficiency energy transfer occurs within micrometers for realistic structures and materials parameters. Scaling laws are derived. Seventy to 90% of the electromagnetic field energy is concentrated in the oxide layer of an MOM diode after the energy is distributed by longer range modes that have less than 0.1% overlap with the tunneling region. The mode conversion allows the requirements separation for energy transport and power production by inelastic tunneling.

Anderson, L. M.↗

The polarization mechanism in CdTe Schottky detectors

Schottky CdTe nuclear detectors are affected by bias-induced polarization phenomena when operating at room temperature. A space charge buildup occurs at the blocking contact causing the degradation in detection performance. By means of Pockels effect, we study the electric field distribution inside the detector and its variation with time and temperature. The analysis of the space charge has allowed us to point out the role of the Schottky contact and of carrier detrapping from deep levels in the polarization mechanism. Moreover, measured current transients have been quantitatively accounted for by the increase in the electric field at the blocking junction.

36 MATERIALS SCIENCE↗

Specific features of light current-voltage characteristics of p-i-n structures based on amorphous silicon in the case of the tunnel-drift mechanism of dark current transport

Current-voltage (I-V) characteristics of p-i-n structures based on amorphous silicon ({alpha}-Si:H) with small hole diffusion lengths (shorter than the thickness of the i-layer of a p-i-n structure) have been experimentally studied with and without illumination. It is shown that forward I-V characteristics of structures of this kind can be described by a dependence inherent in diodes, with a diode ideality factor two-three times the maximum value of 2, theoretically predicted for generation-recombination currents in p-n junctions. The dark current is always substantially lower than the photocurrent in a cell biased with a voltage approximately equal to the opencircuit voltage of the photocell. Dark currents cannot contribute to the I-V characteristic under illumination. The photocurrent decreases with increasing photovoltage at a bias lower than the open-circuit voltage because of a decrease in the collection coefficient and the increasingly important role of back diffusion of electrons into the p-contact, rather than as a result of the dark injection. In the case of biases exceeding the open-circuit voltage, back diffusion becomes the predominant component of the current.

36 MATERIALS SCIENCE↗

Exploring transport mechanisms in atomic precision advanced manufacturing enabled pn junctions

We investigate the different transport mechanisms that can occur in pn junction devices made using atomic precision advanced manufacturing at temperatures ranging from cryogenic to room temperature. We first elucidate the potential cause of the anomalous behavior observed in the forward-bias response of these devices in recent cryogenic temperature measurements, which deviates from the theoretical response of a silicon Esaki diode. These anomalous behaviors include current suppression at low voltages in the forward-bias response and a much lower valley voltage at cryogenic temperatures than theoretically expected for a silicon diode. To investigate the potential causes of these anomalies, we studied the effects of a few possible transport mechanisms, including band-to-band tunneling, bandgap narrowing, potential impact of non-Ohmic contacts, band quantization, impact of leakage, and inelastic trap-assisted tunneling, through semi-classical simulations. We find that a combination of two sets of band-to-band tunneling (BTBT) parameters can qualitatively approximate the shape of the tunneling current at low bias. This can arise from band quantization and realignment due to the strong potential confinement in δ-layers. We also find that the lower-than-theoretically-expected valley voltage can be attributed to modifications in the electronic band structure within the δ-layer regions, leading to a significant bandgap narrowing induced by the high density of dopants. Finally, we extend our analyses to room temperature operation and predict that trap-assisted tunneling (TAT) facilitated by phonon interactions may become significant, leading to a complex superposition of BTBT and TAT transport mechanisms in the electrical measurements.

band gap↗

Photocurrent extraction efficiency in colloidal quantum dot photovoltaics

The efficiency of photocurrent extraction was studied directly inside operating Colloidal Quantum Dot (CQD) photovoltaic devices. A model was derived from first principles for a thin film p-n junction with a linearly spatially dependent electric field. Using this model, we were able to clarify the origins of recent improvement in CQD solar cell performance. From current-voltage diode characteristics under 1 sun conditions, we extracted transport lengths ranging from 39 nm to 86 nm for these materials. Characterization of the intensity dependence of photocurrent extraction revealed that the dominant loss mechanism limiting the transport length is trap-mediated recombination.

14 SOLAR ENERGY↗

Development of reverse biased p-n junction electron emission

A cold cathode emitter of hot electrons for use as a source of electrons in vacuum gauges and mass spectrometers was developed using standard Norton electroluminescent silicon carbide p-n diodes operated under reverse bias conditions. Continued development including variations in the geometry of these emitters was carried out such that emitters with an emission efficiency (emitted current/junction current) as high as 3 x 10-0.00001 were obtained. Pulse measurements of the diode characteristics were made and showed that higher efficiency can be attained under pulse conditions probably due to the resulting lower temperatures resulting from such operation.

Fowler, P.↗