Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Glasses”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

MOLLER Spectrometer Magnet Design With Measured Mechanical Properties of Irradiated S2-Glass Reinforced Cyanate Ester Resin at Elevated Temperature

Here, the aim of this study was to retire the risk of maintaining the integrity of S2-glass reinforced CTD-403 (a cyanate ester resin) that is exposed to radiation and elevated temperature over the life of the measurement of a lepton–lepton electroweak reaction (MOLLER) experiment in experimental Hall A at Jefferson Lab, Newport News, VA. In this article, the shear strength and flexural modulus of irradiated S2-glass reinforced CTD-403 specimens were measured at 65 °C (the magnets are to operate at less than 65 °C) under two scenarios: vacuum and gaseous nitrogen. The testing method is the short-beam shear (SBS) test according to ASTM D2344. The specimens were exposed to neutrons and gamma rays up to 124 MGy. The results show that specimens have excellent resistance against radiation, only 23% degradation of apparent shear strength with 124 MGy at 65 °C under vacuum. At the highest dose areas of the coils, tungsten plates are used to reduce the radiation dose to the resin system. The conclusion is that S2-glass reinforced CTD-403 is well-suited for electrical insulation of MOLLER magnets.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Heat transfer from glass melt to cold cap: Computational fluid dynamics study of cavities beneath cold cap

Efficient glass production depends on the continuous supply of heat from the glass melt to the floating layer of batch, or cold cap. Computational fluid dynamics (CFD) are employed to investigate the formation and behavior of gas cavities that form beneath the batch by gases released from the collapsing primary foam bubbles, ascending secondary bubbles, and in the case of forced bubbling, from the rising bubbling gas. The gas phase fraction, temperature, and velocity distributions below the cold cap are used to calculate local and average heat transfer rates as a function of the bubbling rate. It is shown that the thickness of the cavities is nearly independent of the cold cap shape and the amount of foam evolved during batch conversion. Furthermore, it is ~7 mm and up to ~15 mm for the cases without and with forced bubbling used to promote circulation within the melt, respectively. Using computed velocity and temperature profiles, the melting rate of the simulated high-level nuclear waste glass batch was estimated to increase with the bubbling rate to the power of ~0.3 to 0.9, depending on the flow pattern. The simulation results are in good agreement with experimental data from laboratory- and pilot-scale melter tests.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Revisiting metastable immiscibility in SiO 2 –Al 2 O 3 : Structure and phase separation of supercooled liquids and glasses

Understanding and controlling liquid–liquid phase separation in aluminosilicates is crucial for optimizing glass properties. However, the metastable nature of aluminosilicates’ phase separation has made it difficult to study experimentally, and uncertainty persists regarding the compositional and temperature extents of the miscibility gap. Here, we present new experimental evidence that suggests a consolute temperature between 1440 and 1590°C and endmember compositions of 7 and 62 mol.% Al 2 O 3 for the phase-separated glasses. Using containerless melt processing, deeply supercooled liquids over the 0–60 mol.% Al 2 O 3 range are probed with in situ small- and wide-angle X-ray scattering, which simultaneously reveals changes in nanoscale density heterogeneity and atomic structure. Correlations between phase separation and atomic coordination environments are compared for liquids and glasses. Pair distribution function analysis shows mean O–(Si + Al) coordination increases with Al 2 O 3 content and decreases with temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Corrosion behavior of Monofrax K-3 refractory in borosilicate-based model low activity waste glass melts

Owing to its good chemical and thermal durabilities at high temperatures, Monofrax K-3 refractory is widely used in nuclear waste vitrification as a lining material in melting vessels. However, the corrosion of K-3 refractory during the vitrification of nuclear waste is a serious problem because it affects the melter's safety, performance, and lifetime. Therefore, in the present study, we have focused on unearthing the impact of glass network formers, such as SiO 2 , B 2 O 3 , and Al 2 O 3 , in a model nuclear waste glass composition on the corrosion of Monofrax K-3 refractory. The corrosion tests have been performed per ASTM C621 at 1150°C for 5 days. The dimensional measurements on corroded K-3 refractory suggest that Al 2 O 3 and SiO 2 tend to reduce the refractory corrosion (neck loss), with the effect of Al 2 O 3 being significant. A corroded region on the K-3 refractory at the melt–refractory interface is observed. The corrosion occurs via a coupling of the melt infiltration induced by a capillary effect and the dissolution of Al, Mg, and Fe components from K-3 into the melt through chemical reactions. A Cr-rich layer is retained on the glass contact surface of the corroded K-3 refractory.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Summary Report For The Analysis Of The Sludge Batch 7b (Macrobatch 9) DWPF Pour Stream Glass Sample For Canister S04023 (Rev. 1)

In order to comply with the Defense Waste Processing Facility (DWPF) Waste Form Compliance Plan for Sluldge Batch 7b, Savannah River National Laboratory (SRNL) personnel characterized the Defense Waste Processing Facility (DWPF) pour stream (PS) glass sample collected while filling canister S04023. This report summarizes the results of the compositional analysis for reportable oxides and radionuclides and the normalized Product Consistency Test (PCT) results. The PCT responses indicate that the DWPF produced glass that is significantly more durable than the Environmental Assessment glass.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Composition measurements of the quenched, high-chromium matrix glasses

In this report, the Savannah River National Laboratory provides analyses of glass compositions for a series of simulated Direct Feed High-Level Waste glasses fabricated at the Pacific Northwest National Laboratory. The series included quenched versions of the glasses. These data will be used in the development of improved property/composition models for waste vitrification at Hanford.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Characterization of Hanford LAW phase 3 glasses. Revision 2

This report provides analyses of glass compositions, wash solution compositions, and Product Consistency Test (PCT) leachate compositions for a series of simulated low-activity waste (LAW) glasses fabricated at the Pacific Northwest National Laboratory (PNNL). These data will be used in the development of improved property/composition models for LAW glass at Hanford.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Characterization of the Sulfur-Saturated Melt Versions of the LAW ALG Glasses

This report provides the results from the chemical analyses of a series of sulfur-saturated melt version of the Low Activity Waste Algorithm study glasses, a series of simulated nuclear waste glasses designed and fabricated at Pacific Northwest National Laboratory. These data will be used in the development, validation, and implementation of enhanced property/composition models for waste glass vitrification at Hanford.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Composition Measurements and Product Consistency Test Results for the EMHQ-LBE-04-B Glass

This report provides the results from the chemical analyses of the glass composition and the Product Consistency Test leachate analyses for the EMHQ-LBE-04-B glass. These data will be used in the development, validation, and implementation of enhanced property/composition models for waste glass vitrification at Hanford.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Summary of SRNL Support to the DOE-ORP Enhanced Waste Glass Program for FY23

In fiscal year 2023 (FY23) Savannah River National Laboratory (SRNL) continued tasked work for the Office of River Protection (ORP) to expand glass compositional regions accessible for low-activity waste (LAW) and high-activity waste (HLW) vitrification processing. Experimental work continued in four primary technical areas focused on processing and performance of glasses relevant to the Hanford missions. The data and results from this work will be used to expand and validate the glass models being developed at Pacific Northwest National Laboratory (PNNL) for waste processing and acceptance. This report summarizes the activities and deliverables associated with work performed in FY23.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Summary of SRNL Support Activities to the DOE-ORP Enhanced Waste Glass Program for Fiscal Year 2024

In fiscal year 2024 (FY24) Savannah River National Laboratory (SRNL) continued tasked work for the Office of River Protection (ORP) to expand glass compositional regions accessible for low-activity waste (LAW) and high-activity waste (HLW) vitrification processing. Experimental work continued in four primary technical areas focused on processing and performance of glasses relevant to the Hanford missions. The data and results from this work will be used to expand and validate the glass models being developed at Pacific Northwest National Laboratory (PNNL) for waste processing and acceptance. This report summarizes the activities and deliverables associated with work performed in FY24.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

A brief review of spin glass magnetometry techniques

Spin glasses are inherently dynamical. Taken properly, measurements of these materials can capture their dynamics and provide a wealth of insight into the physics of the spin glass state. In this methods review, two magnetometry methods are directly compared–ac and dc. Because these measurements are taken differently, the resulting data of each method will contain different information about spin glass behavior. This review will specifically focus on how the out-of-equilibrium effects of aging, rejuvenation, and memory manifest in each of these techniques, and how to construct protocols to measure these effects. We then describe the physical significance of each type of measurement and how to interpret their results. Finally, we explicitly detail which applications are most appropriate for which method. This will help the reader select the most helpful technique to carry out their own future experiments.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Resumption-like Increases of Glass Corrosion Rate in Long-term Experiments - 20284

It is shown that physical state and physical changes that occur in the near-surface layers of nuclear waste glasses in contact with water can readily lead to an effective increase of leaching rate which is similar to alteration rate renewal. This increase is similar to third generically accepted stage of glass corrosion termed alteration rate renewal (or resumption) stage when the glass re-starts corroding with the rate similar to that at the initial stage. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Effects of Surface Orientation and Termination Plane on Glass‐to‐Crystal Transformation of Lithium Disilicate by Molecular Dynamics Simulations

Glass‐to‐crystal transformation of lithium disilicate is studied using molecular dynamics simulations using an effective partial charge potential. The structural evolution of the interface between glassy and crystalline lithium disilicate is analyzed to simulate crystallization of glass on pre‐existing crystal seeds. Besides previously used atomic number density, the distribution of Q n species (Si tetrahedra with n bridging oxygen) is shown to be an effective parameter for following this transformation quantitatively. The early stages of crystal growth are significantly affected by the orientation and termination of the surface of adjacent crystal, as indicated by calculated atomic density, partial ordering, atomic segregation, and an increase in Q 3 concentration. In particular, under‐coordinated Si within the outer crystal layer is found to be most effective in transforming the amorphous structure toward crystallinity. The increase in Q 3 in the glass close to interface region most clearly shows the initial stage of lithium disilicate crystal growth.

Sun, Wei↗
DOE OSTI2021

Short- and medium-range orders in Al90Tb10 glass and their relation to the structures of competing crystalline phases

Molecular dynamics simulations using an interatomic potential developed by artificial neural network deep machine learning are performed to study the local structural order in Al90Tb10 metallic glass. We show that more than 80% of the Tb-centered clusters in Al90Tb10 glass have short-range order (SRO) with their 17 first coordination shell atoms stacked in a ‘3661’ or ‘15551’ sequence. Medium-range order (MRO) in Bergman-type packing extended out to the second and third coordination shells is also clearly observed. Analysis of the network formed by the ‘3661’ and ‘15551’ clusters show that ~82% of such SRO units share their faces or vertexes, while only ~6% of neighboring SRO pairs are interpenetrating. Such a network topology is consistent with the Bergman-type MRO around the Tb-centers. Moreover, crystal structure searches using genetic algorithm and the neural network interatomic potential reveal several low-energy metastable crystalline structures in the composition range close to Al 90 Tb 10 . Some of these crystalline structures have the ‘3661’ SRO while others have the ‘15551’ SRO. While the crystalline structures with the ‘3661’ SRO also exhibit the MRO very similar to that observed in the glass, the ones with the ‘15551’ SRO have very different atomic packing in the second and third shells around the Tb centers from that of the Bergman-type MRO observed in the glassy phase.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Athermal glass work at the nanoscale: Engineered electron-beam-induced viscoplasticity for mechanical shaping of brittle amorphous silica

Amorphous silica deforms viscoplastically at elevated temperatures, which is common for brittle glasses. The key mechanism of viscoplastic deformation involves interatomic bond switching, which is thermally activated. Here, for this study, we precisely control the mechanical shaping of brittle amorphous silica at the nanoscale via engineered electron–matter interactions without heating. We observe a ductile plastic deformation of amorphous silica under a focused scanning electron beam with low acceleration voltages (few to tens of kilovolts) during in-situ compression studies, with unique dependence on the acceleration voltage and beam current. By simulating the electron–matter interaction, we show that the deformation of amorphous silica depends strongly on the volume where inelastic scattering occurs. The electron–matter interaction via e-beam irradiation alters the Si–O interatomic bonds, enabling the high-temperature deformation behavior of amorphous silica to occur athermally. Finally, by systematically controlling the electron–matter interaction volume, it is possible to mechanically shape the brittle amorphous silica on a small scale at room temperature to a level comparable to glass shaping at high temperatures. The findings can be extended to develop new fabrication processes for nano- and microscale brittle glasses.

36 MATERIALS SCIENCE↗
DOE OSTI2021

In-situ X-ray and visual observation of foam morphology and behavior at the batch-melt interface during melting of simulated waste glass

We report to attain a basic understanding of the primary foam structure and behavior, which affects the heat and mass transfer and the efficiency of the glass melting process, we investigated the primary foam layer under the glass batch floating on molten glass. The primary foam affects mass transfer during batch melting, in turn affecting the melting process. The recently performed direct in-situ three-dimensional X-ray computed tomography of the batch melting in a laboratory-scale melter vessel allowed us to visualize the features of the reacting batch layer and the foam that develops at its bottom, though with an insufficient resolution of images. In this study, we obtained better temporal and spatial resolution using the two-dimensional X-ray radiography and visual observation of the structure and behavior of transient primary foam as it formed and decayed. As soon as the batch was charged onto the melt surface, foam bubbles began to evolve, grow, and coalesce, forming a primary foam layer, 5-10 mm thick, within tens of seconds. This foam layer was sustained by ongoing gas evolving reactions counterbalanced by bubble coalescence into cavities that moved sideways and escaped to the atmosphere. Eventually, the entire remaining batch turned into foam that gradually decayed at the melt surface. The decay rate agreed with literature observations of surface foam produced by secondary foaming.

36 MATERIALS SCIENCE↗
DOE OSTI2022

High-pressure deformation of metallic glass nanoparticles

Here, the atomistic structure of metallic glasses is closely related to properties such as strength and ductility. Here, Ni 1-x B x metallic glass nanoparticles of two different sizes are compressed under quasi-hydrostatic high-pressure conditions in order to understand structural changes under stress. The structural changes in the nanoparticles were tracked using in situ high-pressure X-ray diffraction (XRD). The ambient pressure pair distribution functions generated from XRD showed that the smaller sized nanoparticles had a more compact amorphous structure with lower coordination number. XRD showed that the amorphous structure was stable up to the maximum pressures achieved. The bulk modulus of the smaller and larger sized nanoparticles was found to be 208 GPa and 178 GPa, respectively. This size-dependent high-pressure behavior was related to compositional differences between the nanoparticles. These results show that Ni 1-x B x metallic glass nanoparticles are highly stable under pressure, which could enable their use as inclusions in metal or ceramic matrix composites.

36 MATERIALS SCIENCE↗