Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Ductility”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Bio‐based glycerol plasticizers for flexible poly(vinyl chloride) blends

Abstract A series of glycerol‐based compounds were investigated for their application as plasticizers for flexible poly(vinyl chloride) (PVC) blends. The effect of plasticizer chemical structure on the performance, migration behavior, and blend morphology were evaluated and compared to blends produced using the commercial plasticizer dioctyl terephthalate (DOTP). Blends containing 40 phr (parts per hundred rubber) of glycerol‐based plasticizer showed a considerable reduction (between 54 to 86°C) in glass transition temperature ( T g ) relative to neat PVC ( T g ~ 80°C). Tensile testing of samples prepared with the glycerol analogs demonstrated higher ductility (elongation at break values of up to 97%) than DOTP (elongation at break value of 75%) at identical plasticizer loadings. The surface morphologies showed excellent incorporation of the glycerol plasticizers functionalized with alkyl chains longer than four carbons in length into the PVC matrix, whereas droplet formation was observed in blends with shorter chain glycerol derivatives. Leaching behavior of the plasticized samples were evaluated into different media and showed that plasticizers comprised of branched, or longer alkyl chains produced 2‐ to 4‐fold lower migration rates compared to those with shorter alkyl chains into polar solutions.

Halloran, Matthew W.↗
DOE OSTI2021

Effect of annealing and supercritical CO 2 exposure at 750°C on the tensile properties of stainless steel and Ni-based structural alloys

Subsize dogbone tensile specimens of alloys 304H, 310HCbN, and 740H were exposed to 30 MPa supercritical CO 2 (sCO 2 ) for up to 4000 h at 750°C. Similar exposures in laboratory air were used to assess the specific role of sCO 2 exposure on the alloy tensile properties. Type 304H specimens were only embrittled by exposure in sCO 2 due to the formation of a thick Fe-rich oxide and C ingress in the bulk of the alloy. For 310HCbN and 740H, no effect of the sCO 2 environment was observed and a decrease of the alloy's ductility was associated with previously observed microstructure evolutions, for example, grain boundary carbide formation. The 740H was tested in the solution annealed condition and self-aging took place during 750°C exposures in sCO 2 and air with the formation of fine gamma prime precipitates leading to significant tensile strength increase. It was found that both 740H and 310HCbN have adequate sCO 2 compatibility for high-temperature commercial applications.

36 MATERIALS SCIENCE↗
DOE OSTI2020

An anisotropic viscoplasticity model for shale based on layered microstructure homogenization

Viscoplastic deformation of shale is frequently observed in many subsurface applications. Many studies have suggested that this viscoplastic behavior is anisotropic—specifically, transversely isotropic—and closely linked to the layered composite structure at the microscale. In this work, we develop a two-scale constitutive model for shale in which anisotropic viscoplastic behavior naturally emerges from semianalytical homogenization of a bilayer microstructure. The microstructure is modeled as a composite of soft layers, representing a ductile matrix formed by clay and organics, and hard layers, corresponding to a brittle matrix composed of stiff minerals. This layered microstructure renders the macroscopic behavior anisotropic, even when the individual layers are modeled with isotropic constitutive laws. Using a common correlation between clay and organic content and magnitude of creep, we apply a viscoplastic modified Cam-Clay plasticity model to the soft layers, while treating the hard layers as a linear elastic material to minimize the number of calibration parameters. We then describe the implementation of the proposed model in a standard material update subroutine. The model is validated with laboratory creep data on samples from three gas shale formations. We also demonstrate the computational behavior of the proposed model through simulation of time-dependent borehole closure in a shale formation with different bedding plane directions.

58 GEOSCIENCES↗
DOE OSTI2024

Arbitrary Order Virtual Element Methods for High‐Order Phase‐Field Modeling of Dynamic Fracture

ABSTRACT Accurate modeling of fracture nucleation and propagation in brittle and ductile materials subjected to dynamic loading is important in predicting material damage and failure under extreme conditions. Phase‐field fracture models have garnered a lot of attention in recent years due to their success in representing damage and fracture processes in a wide class of materials and under a variety of loading conditions. Second‐order phase‐field fracture models are by far the most popular among researchers (and increasingly, among practitioners), but fourth‐order models have started to gain broader acceptance since their more recent introduction. The exact solution corresponding to these high‐order phase‐field fracture models has higher regularity. Thus, numerical solutions of the model equations can achieve improved accuracy and higher spatial convergence rates. In this work, we develop a virtual element framework for the high‐order phase‐field model of dynamic fracture. The virtual element method (VEM) can be regarded as a generalization of the classical finite element method. In addition to many other desirable characteristics, the VEM allows computing on polytopal meshes. Here, we use ‐conforming virtual elements and the generalized‐ time integration method for the momentum balance equation, and adopt ‐conforming virtual elements for the high‐order phase‐field equation. We verify our virtual element framework using classical quasi‐static benchmark problems and demonstrate its capabilities with the aid of numerical simulations of dynamic fracture in brittle materials.

42 ENGINEERING↗
DOE OSTI2024

Acrylonitrile-butadiene-lignin thermoplastic rubber adhesive for enhanced metal-to-metal joining

With the growing requirement for lightweight structural materials in automotive, aerospace, and infrastructure applications, multi-material joints made with adhesive have attracted intense research interest. Commercial thermoset adhesives are one-time cures, and difficult to disassemble the bonded components for repair and recycling. Our prior work with a thermoplastic acrylonitrile-butadiene-lignin rubber (ABL) addresses this sustainability/recycling challenge, but the adhesive exhibits deficient joining strength compared to standard thermosets. Here, we modify the ABL matrix by loading particulate fillers to enhance its modulus and toughness. Further, the goal is to manufacture a cure-free thermoplastic adhesive system with a simple dispensing protocol and characteristic ductility combined with a high yield stress for improved shear strength of a bonded joint. Fumed silica (FS) and epoxidized glass spheres (EGS) were used as fillers in the ABL to promote the dispersion of lignin particles that tailored the functionalities and free energy components of the adhesive surface. With optimal loading of FS (5 wt%) and EGS (30 wt%) in the ABL adhesive matrix, the lap-shear strength of the bonded aluminum joint was elevated by 128%, compared to the neat ABL, reaching 21 MPa, which is 90% of the performance of a commercial epoxy-based adhesive.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Elastic Properties and Deformation Mechanisms in the van der Waals Single-Crystalline Indium Selenide

The bulk van der Waals (vdW) single-crystalline indium selenide (β-InSe) displays exceptional plasticity in a layered crystalline form at both micro- and macroscale. However, the nanoscale origin of plasticity remains unclear. Herein, an atomic-level study on the deformation mechanisms of InSe by using first-principles calculations is reported. Remarkable anisotropic elasticity is observed in the vdW InSe layered crystal, and the stiffness is dramatically softened because of the vdW gap in the layered structure. The simulations capture the distinct fracture modes in the uniaxial tensile deformation, depending on the loading directions—brittle fracture in the [100] and [110] directions while ductile failure in the [001] direction. The InSe layered crystal structure exhibits superplastic deformability under uniaxial compression. Different transition pathways, including interlayer tangling, amorphization, and cross-linking, are tracked along respective deformation directions. The unprecedented plasticity of InSe layered crystals can be attributed to the phase transition coupled with interlayer gliding and cross-layer dislocation slipping. Here, this study deepens our understanding of the deformation mechanisms of layered materials at the atomistic level and provides insights into tailoring material properties for low-dimensional material design based on its deformation mechanisms.

2D materials↗
DOE OSTI2024

Strain Field Around Individual Dislocations Controls Failure

Understanding material failure on a fundamental level is a key aspect in the design of robust structural materials, especially for metals and alloys capable to undergo plastic deformation. In the last decade, significant progress is made in quantifying the stresses associated with failure in both experiments and simulations. Nonetheless, the processes occurring on the most essential level of individual dislocations that govern semi-brittle and ductile fracture are still experimentally not accessible, limiting the failure prediction capabilities. Therefore, in the present work, a one-of-a-kind nanoscale fracture experiment is conducted on a single crystalline Cr bending beam in situ in the transmission electron microscope and for the first time quantify the transient strains around individual dislocations, as well as of the whole dislocation network during crack opening. The results reveal the importance of both pre-existing and newly emitted dislocations for crack-tip shielding via their intrinsic strain field and provide guidelines to design more damage tolerant materials.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Enhancing Mechanical Properties of Carbon–Silicon Steel through Two–Stage Quenching and Partitioning with Bainitic Transformation: Ultimate Tensile Strength of 1875 MPa and Total Elongation of 8.03%

To achieve the desired microstructural properties, the ongoing development and innovation in new structural steels require novel thermal processing. This study aims to improve the mechanical properties of a commercial spring carbon–silicon steel by tailoring its microstructure through a process involving quenching and partitioning (Q&P) followed by bainitic transformation. A two–stage Q&P process is proposed to generate a nanoscale dispersion of stable retained austenite and carbides within the tempered martensite and bainite microstructure. The resulting tensile properties demonstrate a yield strength of 1280 MPa, an ultimate tensile strength of 1875 MPa, and a total elongation of 8.03%. These values surpass those of conventional spring 9254 steel, highlighting the effectiveness of the thermal treatment design. Microstructure analysis reveals the presence of tempered martensite, bainite sheaves, nanoscale carbides, and aggregates of retained austenite. Moreover, the resulting body–centered cubic matrix exhibits minimal lattice tetragonality of ≈1.0051, coupled with stable retained austenite featuring a carbon concentration of ≈3.42 ± 0.5 wt%, resulting in outstanding strength–ductility properties. In conclusion, these findings indicate that the proposed two–stage Q&P process, followed by bainitic transformation, significantly enhances the mechanical properties of carbon–silicon steels, making it a promising candidate for high–performance spring applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Sensitization and Mechanical Response of Cu‐Containing Steel Rods

The iron and steel manufacturing sector significantly adds to global greenhouse gas emissions, caused primarily by the carbothermic reduction of iron ore. Recycling scrap steel offers an effective decarbonization strategy but introduces impurities like copper (Cu) that can negatively impact mechanical properties. This study investigates the effects of Cu content and heat treatment on the mechanical performance and sensitization of steel wire rods for tire manufacturing. Steel rods with 0.04 and 0.21 wt% Cu are heated to 1050 or 1200 °C, then air quenched, or furnace cooled. Tensile testing coupled with microscopic analysis is used to evaluate mechanical properties and assess the sensitization effects. Higher Cu content leads to larger sensitized zones with increased Cu precipitation along grain boundaries. Ductility and toughness, crucial for wire drawability, are found to be reduced, despite higher ultimate strength. Slower furnace cooling is seen to result in smaller sensitized zones compared to air quenching, suggesting a pivotal role of cooling rate in sensitization control. The findings provide insights into optimize heat treatment parameters and Cu content limits, balancing mechanical performance and maintaining drawability for enhanced scrap steel recycling in tire production.

copper↗
DOE OSTI2021

Precipitate Phase Stability and Mechanical Properties of Alloy 263 and Variants in Wrought or Cast Form

Alloy 263 is a candidate Ni-based superalloy for use in advanced ultra-supercritical (AUSC) power plants that are targeted to operate above 700 °C. Exposure times in this type of environment are considerable with target creep properties specified at 100,000 h making phase stability an important parameter in the alloy selection process. In this investigation, the microstructure of alloy 263 and two modified compositions in both cast and cast/wrought forms were investigated after exposure at 800 °C for various times ranging from 1,000 h to 10,000 h. Tension and creep properties were assessed for all alloys in both forms. Modification to the Ti and Al concentrations successfully slowed down the γ' to η transformation while doubling the γ' fraction. Thin elongated η needles or platelets formed in the wrought products while thicker, plate-like, η precipitates were found in the castings. The effect of the various microstructures on the creep properties were determined using isothermally aged specimens aged at 800 °C for 3,000 h and 10,000 h prior to creep screening. Strong precipitation of the η phase was found to considerably decrease creep life and increase minimum creep rate. By modifying the Ti and Al content, the creep life and ductility of the new formulation tested on specimens isothermally aged for 3,000 and 10,000 h were near that of the nominal alloy in its standard aged condition.

Detrois, Martin↗
DOE OSTI2021

Mechanical Behavior of High-Entropy Alloys: A Review

High-entropy alloys (HEAs) are materials that consist of equimolar or near-equimolar multiple principal components but tend to form single phases, which is a new research topic in the field of metallurgy, and have attracted extensive attention in the past decade. The HEAs families contain the face-centered-cubic (fcc), body-centered-cubic (bcc), and hexagonal-close-packed (hcp)-structured HEAs. On the one hand, mechanical properties, e.g., hardness, strength, ductility, fatigue, and elastic moduli, are essential for practical applications of HEAs. Scientists have explored in this direction since the advent of HEAs. On the other hand, the pursuit of high strength and good plasticity is the critical research issue of materials. Hence, strengthening of HEAs is a crucial issue.In this chapter, we reviewed the recent work on the room-temperature elastic properties and mechanical behavior of HEAs, including the mechanisms behind the plastic deformation of HEAs at both low and high temperatures. Furthermore, the present work examined the strengthening strategies of HEAs, e.g., strain hardening, grain-boundary strengthening, solid-solution strengthening, and particle strengthening. The fatigue, creep, and fracture properties were briefly introduced. Lastly, the future scientific issues and challenges of HEAs were discussed.

Shang, Yuanyuan↗
DOE OSTI2022

Effect of post-extrusion heat treatment on mechanical property of aluminum alloy 2024 tube produced using Shear Assisted Processing and Extrusion (ShAPE)

The present work deals with the Shear Assisted Processing and Extrusion (ShAPE) of aluminum alloy 2024 tubes and mechanical property optimization via post extrusion heat treatments (T3510 and T8510). The ShAPE process enables extruding AA2024 at an extrusion speed of 7.4 m/min and extrusion temperature of 480 °C, which is otherwise beyond the extrudability limit of this alloy using conventional extrusion techniques. The ultimate tensile strength reaches 466 MPa for ShAPE+T3510 condition and 503 MPa for ShAPE+T8510 condition, both of which exceed the corresponding ASTM/ASM (minimum/typical) values for the studied tube geometry. The yield strength reaches 382 MPa for ShAPE+T3510 condition and 481 MPa for ShAPE+T8510 condition, both of which surpass any reported values in the literature or the highest industrial values. In addition, the ductility of AA2024 tube fabricated from ShAPE+T3510 or ShAPE+T8510 are evidently improved by the grain size refinement, second phase refinement, and enhanced uniformity in second phase distribution due to the severe plastic deformation of ShAPE process.

Shear Assisted Processing and Extrusions (ShAPE), ↗
DOE OSTI2022

Exploring the Microstructure-Property Relationship of Mg-Al-Mn alloys enhanced via Friction Stir Processing

Friction Stir Processing (FSP) is a solid-state thermomechanical processing technique that enables local grain refinement, densification, and homogenization of microstructure in metallic components. Here, FSP is applied to thin sheets of high-pressure die cast AM60 to address the porosity and heterogeneities inherent to the casting process. In this work, microstructure characterization is correlated to improvements in the static mechanical properties of the Mg-Al-Mn alloy system at various FSP processing conditions. Notably, there is a significant increase in the ductility and ultimate tensile stress of system following FSP. The dominant deformation mechanisms for the as-cast material and the FSP material are investigated. Finally, the fatigue life improvement is correlated to microstructure modifications that may lead to distinct behavior in crack initiation and crack propagation for the as-cast and FSP material.

Garcia, David↗
DOE OSTI2025

Friction Self-piercing Riveting Process for 3T Configuration of AA7075-AA7075-AA6022

Friction self-piercing riveting (F-SPR), as a solid-state joining process that generates frictional heat during the process, was utilized to join a 3 T configuration of low-ductility AA7075-AA7075-AA6022 sheets. A multi-step F-SPR process was employed to precisely control the mechanical interlocking and solid-state joining, ensuring a strong joint formation. With control of the plunge depth when the transition from rivet penetration to rivet flaring, two joining conditions were developed to assess mechanical joint integrity: one bearing deep penetration with a smaller interlock, and the other yielding a shallow penetration with a larger interlock. Both strategies met the criteria for a sound rivet joint. Customized lap shear tensile configurations were designed to assess the joint strength at interface between first and second layers, as well as between second and third layers. Both conditions demonstrated great joint strength between the first and second layers, while deeper penetration approach showed stronger solid-state joint, leading to improved joint strength between the second and third layers.

Wang, Tianzhao [ORNL] (ORCID:0000000315337602)↗
DOE OSTI2020

Interfacial toughness: dependence on surface roughness and test temperature

Interfacial toughness quantifies resistance to crack growth along an interface and in this investigation the toughness of an aluminum/epoxy interface was measured as a function of surface roughness and test temperature. The large strain response of the relatively ductile epoxy adhesive used in this study was also characterized. This epoxy adhesive exhibits intrinsic strain-softening after initial compressive yield and then deforms plastically at a roughly constant flow stress until it rapidly hardens at large compressive strains. Here, we find that interface toughness scales as the product of the temperature dependent epoxy yield strength and a length scale that characterizes surface roughness. The proposed scaling is based upon dimensional considerations of a model problem that assumes that the characteristic length scale of both the roughness and the crack-tip yield zone is small relative to the region dominated by the linear elastic asymptotic crack-tip stress field. Furthermore, the model assumes that interfacial failure occurs only after the epoxy begins to harden at large strains. The proposed relationship is validated by our interfacial toughness measurements.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Thermodynamics and kinetics of precipitation and austenite reversion during aging of Ti-free grade 300 maraging steel manufactured by laser powder bed fusion (LPBF)

Austenite reversion and intermetallic precipitation are two key phase transformations in maraging steels which determine the strength and ductility. Usually, an optimum aging temperature/time is determined using trial and error approach with inputs from thermodynamic databases and a-posteriori microscopy/hardness evaluations. In this study, a thermo-kinetic model is developed to predict the precipitation and austenite reversion kinetics during various post-fabrication heat treatments in a Ti-free variant of grade 300 maraging steel manufactured using laser powder bed fusion. The thermo-kinetic model was based on the principles of Scheil solidification and the classical nucleation theory. The predictions from the thermo-kinetic model were verified using suitable microscopy techniques, and the results from the thermo-kinetic model agree well with the experimental measurements. Overall, results highlight the fact that an Integrated Computational Materials Engineering approach can be used to predict the precipitation and austenite reversion kinetics, and be used as an input for an efficient design of heat treatments for achieving optimum mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Microstructural refinement in ultrasonically modified A356 aluminum castings

Two A356 aluminum alloys (Al-Si-Mg), one with 0.09 wt.% Fe and one with 0.91 wt.% Fe, were cast in a graphite mold with the simultaneous application of local ultrasonic intensification to refine the as-cast microstructure. Ultrasonication during casting transformed the morphology of primary Al grains from dendritic (~140-290 microns in size) to globular (~33-36 microns in size). The alloy with high Fe exhibited globular grains at distances up to 45 mm away from the ultrasound probe, while the alloy with low Fe exhibited globular grains at distances only up to 6 mm away from the ultrasound probe. Near the location of the ultrasound probe (< 2 mm away), a second non-dendritic microstructural morphology was observed with fine aluminum grains (~9-25 microns in size). This unique fine-grained morphology has not been previously reported, contains a greater concentration of Si relative to the globular microstructure, and may be a large, fully eutectic region. Ultrasonication during casting also transformed the morphology of the ß-Al 5 FeSi phase particles (which are deleterious to the strength and ductility of the alloy) in the high Fe alloy from needle-like to rectangular, which could enable the greater use of secondary Al alloys. Thermodynamic simulations conducted to calculate the solidification paths of the two alloys studied predict that the ß-Al 5 FeSi phase begins to form earlier in the alloy with high Fe. Finally, data suggest that the ß-Al 5 FeSi phase (which is more abundant in alloys with high Fe content) may enhance ultrasonically-induced grain refinement.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Mechanical and Corrosion Response of 316SS in Supercritical CO 2

The supercritical carbon dioxide (s-CO 2 ) Brayton cycle is currently being explored as a replacement for the steam Rankine cycle due to its potential for higher efficiency and lower cycle cost. 316 stainless steel is a candidate alloy for use in s-CO 2 up to roughly 600 °C, but the mechanical effects of prolonged exposure of base and welded material in s-CO 2 have not been analyzed. The potential for carburization makes this an important concern for the implementation of 316 and similar austenitic stainless steels in the s-CO 2 environment. In this study, welded and base material of two types of 316–316L and 316H–were exposed in either s-CO 2 or argon at 550 °C or 750 °C for 1000 h. 550 °C s-CO 2 exposure yielded a thin (< 1 µm) Cr oxide with occasional nodules of duplex Fe oxide and Fe–Cr spinel that were up to 5 microns thick. However, tensile results from s-CO –2 exposure matched those of 550 °C thermal aging in Ar, indicating that no mechanically detrimental carburization occurred in either 316 variant after 1000 h exposure. Conversely, 750 °C s-CO 2 exposure produced roughly 10 × the oxide thickness, with a more substantial Fe oxide (3–5 µm) on the majority of the surface and nodules of up to 40 µm thick. In comparison to aged samples, tensile testing of 750 °C CO 2 -exposed samples revealed ductility loss attributed to carburization. As a result, projections of 316L performance in s-CO 2 indicate that mechanically detrimental carburization—equal to that shown here for 750 °C, 1000 h—will likely be present after 7–14 years of service at 550 °C.

316 stainless steel↗