Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Damage evolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

TPSAS-NF1676L-17800-DND

Currently, there are two national challenge problems that guide much of the research in durability and damage tolerance at NASA Langley. The first, Airframe Digital Twin, is a concept that combines as-built vehicle components, as-experienced loads and environments, and other vehicle-specific characteristics to enable ultrahigh fidelity modeling of aircraft and spacecraft throughout their service lives. The second, Materials Genome Initiative, is an analog to the Human Genome Project, and is intended to improve the rate at which materials scientists can discover, understand fundamental physics, and improve material systems. This presentation will highlight several research projects ongoing at NASA Langley that are in support of the above challenge problems. Two of those topics will be the subject of detailed discussion. First, investigations of microstructurally-small fatigue cracking (MSFC) in Al-2Cu and Al-4Cu, fabricated in-house, will be presented. Single- and oligo-crystals of Al-Cu specimens were loaded in uniaxial fatigue, while high-resolution in-situ measurements of deformation were made using image correlation (IC) in a scanning-electron microscope (SEM). The Al-Cu specimens were then replicated as crystal plasticity finite element models (CPFEM), where evolution of slip localization near grain boundaries was computed. Comparison among experiment and CPFEM is made. In addition, XRay diffraction measurements of the as-fabricated specimens were carried out, where direct measurements of the embedded copper precipitates were made, and their influence on growing MSFCs were directly observed. The second main topic will illustrate ongoing work in the area of so-called damage-sensing particles. In this work, shape-memory alloys are embedded in an aluminum alloy matrix. Upon the propagation of a fatigue crack, these particles undergo a strain-induced phase transformation which is detected using an acoustic sensor, providing real-time information on propagating cracks. Experiments and simulations regarding the development of this system will also be detailed.

Jacob Hochhalter↗
DOE OSTI2025

Important Human Actions for Advanced Reactors: Implications for Human Factors

As advanced reactor platforms continue to develop and gain traction in the energy sector there is a need for risk-informed, scalable regulations that match that progress. This is a core component of the U.S. Nuclear Regulatory Commission’s proposed Part 53 Rule Making; the Accelerating Deployment of Versatile, Advanced Nuclear for Clean Energy (ADVANCE) Act; and other efforts that seek to update nuclear power regulations. This paper covers one key aspect of that regulatory evolution: Important Human Actions (IHA). In this paper, we discuss how the understanding and definitions of IHAs have changed and what that means for human factors engagement through the process of developing these technologies. Instead of a narrow focus on control actions that led to an increase in core damage risk, the new focus is on IHAs is “wherever they occur.” What this means is that having a highly automated or passive safety system does not eliminate IHAs. Rather, it shifts the focus point to all the actions that enable these systems. Everything from maintenance, to design, to training can be considered an IHA and that dramatically shifts the efforts and level of engagement necessary for human factors to enable these technologies. We discuss the notions of risk-informed human factors that underpin these efforts, give several examples, and briefly describe the risk assessment methodologies that will be needed. In the past, IHAs were identified and then became a focus point of human factors engineering (HFE) activities to ensure a robust evaluation of the task was completed. The future is less clear. HFE for nuclear energy will need to evolve and become more integrated in technology development than ever before.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

An atom probe tomography and inventory calculation examination of second phase precipitates in neutron irradiated single crystal tungsten

Tungsten is the prime candidate material for the plasma facing divertor system and first wall armor of future nuclear fusion reactors. However, the understanding of the microstructural and chemical evolution of pure tungsten under neutron irradiation is relatively unknown, in part due to a lack of experimental data on this topic. Here, single crystal tungsten has been irradiated in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory at a nominal temperature of 700–800 °C to damage levels of 0.1 and 1.8 displacements per atom (dpa). Inventory calculations of the neutron irradiation experiments have been used to track isotope generation and decay to inform atom probe tomography (APT) results in the determination of the transmutation-induced precipitate compositions. Furthermore, APT crystallography has been used to show the relationship between precipitates and matrix. The composition of the precipitates is shown to progress towards that of the σ-phase at the highest dose studied, with those precipitates lying along crystallographic planes similar to those of displacement-induced dislocations. This work also sets the framework for APT studies of materials that contain isotopic ratios far from those observed in the natural state.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

Geophysical Signatures of Crack Network Coalescence in Rocks at Multiple Length Scales

The main goal of the research project was to identify the geophysical signatures of fracture growth in natural rocks by utilizing novel geophysical techniques. The research objectives were to (a) investigate the potential for geophysical methods to determine when cracks initiate, the types and locations of propagated cracks, and the coalescence of networks of cracks in natural rocks at multiple scales, (b) determine how damage at the microscale evolved into damage at the macroscale and then link the microscopic and macroscopic observations, (c) quantify crack coalescence in rocks under realistic stress conditions using coupled mechanical-geophysical-optical visualization, and (d) identify the precursors in geophysical signals to crack coalescence. The following research thrusts were explored to achieve the research objectives: (1) uniaxial compression testing of rock specimens with and without a set of pre‐existing flaws and (2) triaxial compression testing of natural rock specimens. These thrusts allowed for exploring fracturing in rocks under realistic in situ environments and at multiple scales. This project provided educational opportunities for nine graduate and undergraduate students and resulted in 27 peer-reviewed publications. This first research thrust focused on investigating the micromechanics of fractures in rocks through uniaxial compression testing combined with advanced geophysical and imaging techniques, specifically acoustic emission (AE) monitoring, ultrasonic imaging, and 2-dimensional Digital Image Correlation (2D-DIC). By examining damage processes under time-independent and time-dependent loading conditions, insights into damage localization, crack initiation, and fracturing mechanisms were gained. It was observed that the AE signals and the strain-based measurements directly reflect the state of damage in the rock specimen and could be used to identify the cracking levels, such as the crack initiation (CI) and crack damage (CD), and the mode of deformation. A novel calibration apparatus was developed to enhance the accuracy of AE sensors, allowing for the estimation of key parameters such as magnitude, source dimension, stress drop, and radiated seismic energy associated with the fractures. The findings highlighted significant variations in the temporal evolution of AE source parameters during the primary, secondary, and tertiary stages of creep, identifying tensile cracking as the primary deformation mode. The second research thrust focused on enhancing the understanding of fracturing processes in natural rocks through triaxial compression testing, real-time AE monitoring, and ultrasonic monitoring. We investigated the impact of various factors such as fracture propagation regimes, injection parameters, rock types, and pre-existing conditions on the hydraulic fracture (HF) behavior using scaled true-triaxially loaded specimens of Barre granite and Lyons sandstone. Custom sensor housing facilitated concurrent active and passive monitoring to analyze hydro-mechanical responses and microseismicity associated with different HF scenarios. A coupled investigation of passive microseismicity and active signal attributes permitted a detailed comprehension of the various HF processes (aseismic deformation, fracture initiation and propagation, fluid permeation, and leak-off) and their dependence on the specific rock type. The findings of this research demonstrated the effectiveness of AE monitoring techniques in providing valuable insights into the impact of various factors on the behavior and dynamics of HF processes. The advancements in monitoring techniques, offering a more thorough and precise approach, represent a significant step towards optimizing HF practices and ensuring sustainable resource extraction.

58 GEOSCIENCES↗
NASA NTRS2019

Nasa GeneLab Computomics Reveal Horizontal Gene Transfer on International Space Station Environmental Metagenomes

Prokaryotic lifeforms can be observed to demonstrate many keen adaptive advantages, perhaps facilitated by a nature simplistic relative to divergent domains of life. In particular, decompartmentalized gene expression facilitates adaptation by allowing free exchange of genetic material, albeit at the cost of increased susceptibility to genetic damage. Thus, these lifeforms must compensate by embracing diverse investment strategies in an attempt to “brute force” the evolvability equation through precipitous genesis, lean metabolic efficiency, and sheer population. This prokaryotic archetype also enables symbiotic relationships with secondary mobile genetic elements known as plasmids, which have been shown to drive evolution on rapid temporal scales through processes such as conjugation and transformation. This study attempts to decipher whether these mechanisms of horizontal gene transfer (HGT) are major factors in determining prokaryote fitness within a unique isolated environment, the International Space Station (ISS). The ISS Microbial Tracking (MT) project has generated a wealth of data concerning the successive reigns of microbial genera that appear to thrive amidst harsh conditions for life. Despite relatively higher doses of ionizing radiation as compared to Earth, complications associated with microgravity, and the anti-microbial mélange deployed, microbial life still persists in this environment. The NASA GeneLab serves as a data repository and analysis platform to enable researchers to access space flight factor related data. With the use of GeneLab’s modern computational suites (computomics), phylogenetic and functional genomic investigations of HGT events were conducted on the data generated from the MT-1 project. The putative data concerning the plasmid population (plasmidome) of the ISS was algorithmically derived and compared to those of habitats with similar environmental dynamics- such as living quarters and hospitals- to investigate whether these HGT elements may play crucial role(s) in shaping the microbiome of this closed habitat that serves as the only inhabited structure in space.

Bense, Nicholas↗
DOE OSTI2022

Microstructural evolution and precipitation in γ-LiAlO 2 during ion irradiation

Polycrystalline γ-LiAlO 2 pellets were sequentially irradiated with 120 keV He + and 80 keV D 2 + ions to the fluences of 1 × 10 17 and 2 × 10 17 (He + + D + )/cm 2 at 573 K. Additional irradiation was performed to a fluence of 2 × 10 17 (He + + D + )/cm 2 at 773 K. The irradiated pellets were characterized using scanning transmission electron microscopy, time-of-flight secondary ion mass spectrometry, and grazing incidence x-ray diffraction. Lattice damage, amorphization, and fractures are observed with no evidence for the formation of secondary-phase precipitates in the pellets irradiated up to an ion fluence of 2 × 10 17 (He + + D + )/cm 2 at 573 K. In contrast, faceted precipitates with sizes larger than 100 nm formed in a pellet irradiated to 2 × 10 17 (He + + D + )/cm 2 at 773 K. Analyses of the diffraction and composition data suggest that the precipitates have a spinel-type structure, likely a non-stoichiometric LiAl 5 O 8 with Li depletion. This could be an intermediate phase with Li atoms at the octahedral and possibly tetrahedral sites as well. It is speculated that as the dose increases, Li loss will continue and the precipitates will approach a composition of alumina primarily in phases of α-Al 2 O 3 and amorphized Al 2 O 3 .

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2020

A mechanism-based quantitative multi-scale framework for investigating irradiation hardening of tungsten at low temperature

We present the development and validation of a mechanism-based multi-scale modeling framework to quantitatively link the irradiation defect evolution kinetics at the microscopic scale to the macroscopic yield strength and flow stress evolution of tungsten irradiated at low temperature (0.08 < T/T m < 0.18, where T m is the melting point and is equal to 3673 K). The mechanism-based strength model, proposed as the superposition of thermal softening and modified dispersed barrier hardening, is developed to understand the underlying strengthening mechanisms. The thermal softening exponent as defined in the Johnson-Cook model is obtained by fitting unirradiated yield strength at different temperatures. A set of irradiation-induced defect kinetics equations with the thermodynamics parameters derived from the atomic calculations reported in the literature is used to determine the densities and sizes of defect clusters at the meso-scale, and the predicted irradiation damage characteristics are in reasonable quantitative agreement with experimental data from literature. The effects of irradiation condition (temperature and irradiation dose) and test temperature on yield strength are quantitatively predicted and compared with experimental measurements from the literature. Here, the predicted irradiation hardening and strain hardening are compared with experimental data as model validation.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Development and performance of INCONEL® alloy 740H® seam-welded piping

INCONEL® alloy 740H® is an age-hardenable nickel-based alloy approved for pressure vessels and piping within ASME Section I, VIII, and B31.1. Currently, the code applies a weld strength reduction factor (WSRF) of 0.7 to the allowable stresses for longitudinal seam welds in the time dependent creep regime. In this work, a full-scale seam weld was successfully produced using typical industrial practices. The component was solution heat-treated and aged after fabrication to improve the performance of the weldment. Tensile, bend, impact, and low-cycle fatigue tests showed the component met all the specification requirements and elevated temperature properties were within base metal expectations with failures predominately in the weld metal. Long-term creep tests, including large samples more representative of the entire weldment, were fabricated and tested to times in excess of 10,000 h at multiple temperatures. Analysis of the creep data supports a WSRF of 0.9 for the solution annealed + aged weldments in contrast to the WSRF of 0.7 currently applied to welded + aged weldments. Metallurgical analysis shows that the solution annealing causes recrystallization of the weld metal and reduces the chemical compositional and microstructural gradients in the weldments resulting in acceptable short-term performance. In long-term creep, evidence for coarsened zones in the weldments due to discontinuous coarsening reactions were identified as the mechanism leading to accelerated creep damage formation in the weld metal and sample failure.

14 SOLAR ENERGY↗
DOE OSTI2021

Evaluating the grain-scale deformation behavior of a single-phase FCC high entropy alloy using synchrotron high energy diffraction microscopy

We report although the deformation behavior of high-entropy alloys (HEAs) has been extensively studied at the macroscale, many important properties have yet to be explored for these alloys at the microscale, thus hampering accurate prediction of damage and failure processes. Synchrotron high-energy diffraction microscopy (HEDM) and fast-Fourier transform-based crystal plasticity modeling was conducted to investigate the three-dimensional (3D) grain-resolved micromechanical response for approximately 1,900 constituent grains within a single-phase FCC HEA up to 1% applied strain. The evolution of grain-resolved elastic strains, lattice reorientations, and maximum resolved shear stresses (mRSS) were evaluated to quantify elastic, yield, and fully plastic behavior. Overall, the initial critical resolved shear stress (CRSS), determined via in situ HEDM and companion modeling, was found to be > 20% higher than estimated using the classical polycrystalline Taylor factor (M = 3.06). However, a descriptive parameter based on the average grain-resolved Taylor factor ($\overline{M}$) was found to show excellent agreement with plastic yielding behavior observed within HEDM datasets. Noticeable deviations in HEDM lattice reorientations compared to both EVP-FFT simulations and classical predictions for FCC polycrystals were discovered, highlighting the complexity in correlating local lattice reorientations, Taylor, and Schmid factors with plastic response for this material at the grain-scale. Therefore, it is anticipated that the overall trends and parameter identification of 3D grain-resolved properties in this study can serve as an important foundation for continued mesoscale investigation on both well-established and newly developed Cantor-like HEAs.

36 MATERIALS SCIENCE↗
NASA NTRS1986

Galaxies as dynamical probes of cluster structure

The effects of galaxy-cluster tidal forces on the dynamical evolution of member galaxies are investigated by means of numerical simulations. The kinds of normal events in clusters that can have significant immediate or long-term effects on galaxies are reviewed; the principal cluster properties are discussed; and the simulation results are briefly characterized, summarizing the report of Miller (1986). The degree of damage to a galaxy is found to depend strongly on the distance at which it orbits the cluster center and on the 'hardness' of the cluster potential. It is suggested that observations of the internal structure of cluster galaxies can be used to explore the cluster gravitational potential near the center and help locate and identify the nonluminous mass.

Miller, R. H.↗
DOE OSTI2023

Effects of sub‐mm cylindrical voids on detonation performance in PBX 9501

Abstract Internal features of varying scale and geometry are always present in explosives systems. Below a critical length, dependent on the explosive, these features can operate as a driving force for energy concentration and reaction, known as hotspots. At larger length scales, internal features result in jetting and detonation wave shaping, allowing for bulk work to be done by the explosive as is seen in shape charges. To date, a large volume of work has been performed to simulate hotspot ignition and large‐scale wave shaping. However, little experimental data exists on the effects of features in intermediate length scales, 0.1 to 1 millimeter. It has been observed in many tests that these small‐scale features can influence the high explosive (HE) performance and in some cases cause substantial damage to adjacent systems. This work provides quantitative data on the effects of machined voids moderately above more typical hotspot lengths, 0.3–0.8 mm in diameter, in PBX 9501 pressed to 1.785 g cm −3 ±2.5 mg cm −3 . Streak imaging was used to visualize void collapse, jet velocity, re‐initiation time, and wave shape evolution. Delay in detonation front propagation time was found to be linearly dependent on the void diameter and jet velocity was found to be independent within the tested range and resolution. Cut‐back experiments were used to investigate wave shape distortion and evolution downstream of the void, showing consistent growth and decay shapes across all void sizes. Simulations using CTH, a hydrocode by Sandia National Laboratory, were used to investigate void collapse showing agreement with the trends of experimental results but yielded inaccurate wave shape development delay values. Both simulation and experimental results identified several re‐initiation mechanisms with jetting and subsequent double shocking of localized HE being the dominant mechanisms for the void sizes that were studied.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2024

Spectroscopic analysis of Pu-bearing compounds in double-walled cells

Spectroscopic analysis of radiological materials has been historically limited to radiological labs with older or less advanced scientific instrumentation. The development of double-walled cells (DWCs) at the Savannah River National Laboratory (SRNL) has enabled Pu-bearing compounds to be removed from radiological laboratories and studied in our radiologically clean spectroscopy laboratory with state-of-the-art instrumentation. In this manuscript, we discuss the contributions of DWCs that have allowed the application of Raman spectroscopy, diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS), diffuse reflectance spectroscopy (DRS) in the shortwave infrared, and gamma spectroscopy at SRNL. Significant advances have been made in the understanding of the thermal decomposition of Pu(III) and Pu(IV) oxalates, alpha-induced damage to the PuO 2 crystal lattice, and the effect of calcination temperatures on the quality of PuO 2 . These techniques have enabled methods to conduct PuO 2 age dating since last calcination and estimate the calcination temperature with Raman spectroscopy and DRS. Additional spectroscopic information measured with DRIFTS has enabled the observation of the evolution of carbon species with calcination temperature, while gamma spectroscopy provides information on age dating since last purification.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
NASA NTRSDate not supplied

Solar Energetic Particle Tracks in Itokawa Samples: Implications for Regolith Development on Near-Earth Asteroids and Space Weathering

JAXA’s Hayabusa mission returned the first surface samples from a near-Earth asteroid for laboratory analyses. The Hayabusa samples thus provide a special opportunity to directly investigate the evolution of asteroidal surfaces, from the development and evolution of the regolith to the study of space weathering effects. The lack of a protective atmosphere on airless bodies results in regolith grains being exposed to a wide range of radiation sources and effects. We focus here on solar energetic particles (SEP) with Z>20, mainly Fe group nuclei, that leave trails of ionization damage (tracks) in insulating materials that accumulate with time and provide clues about the near-surface exposure age of regolith materials.

L P Keller↗
DOE OSTI2024

Dynamic Scaling Analysis of Accelerated Irradiation Testing on Additive Manufacturing Materials by Positron Annihilation

The timely applications of Additive Manufacturing (AM) materials in nuclear environments require accelerated irradiation tests, mainly ion irradiation to enable rapid prototyping. Low dose ion irradiation would cause sub-nanostructure changes by generation of lattice defects, vacancies, vacancy clusters and voids and void swelling caused by cellular dislocations. Positron Annihilation Lifetime (PAL), a novel technology, sensitive towards sub-nanostructure morphology with high accuracy (about 10-7 vacancy per atom), supported by Transition Electron Microscope (TEM) would be applied to identify the type and total size of the defects. The subsequent PAL measurements and TEM surface studies would be followed by PAL analysis that includes sophisticated trapping model. The PAS results would become an input to dynamic scaling analysis (that predicts radiation effects from low dose studies for high dose effects), which incorporate mean-field theory model. The final effect is an in-depth understanding of the microstructure evolution of AM materials under ion irradiation which can be extrapolated to the studies of neutron irradiation, since ion-irradiation takes less time and do not cause the irradiation hazard. The working hypothesis is that PAL technology, that have excellent sensitivity to low-defect concentration would help to identify ion-induced material damage on the atomic and nano-scale level, which then could be extrapolated to understand the neutron damage better.

accelerated irradiation testing↗
NASA NTRS2010

Monte-Carlo Simulation of Heavy Ion Track Structure Calculation of Local Dose and 3D Time Evolution of Radiolytic Species

Heavy ions have gained considerable importance in radiotherapy due to their advantageous dose distribution profile and high Relative Biological Effectiveness (RBE). Heavy ions are difficult to produce on Earth, but they are present in space and it is impossible at this moment to completely shield astronauts from them. The risk of these radiations is poorly understood, which is a concern for a 3-years Mars mission. The effects of radiation are mainly due to DNA damage such as DNA double-strand breaks (DSBs), although non-targeted effects are also very important. DNA can be damaged by the direct interaction of radiation and by reactions with chemical species produced by the radiolysis of water. The energy deposition is of crucial importance to understand biological effects of radiation. Therefore, much effort has been done recently to improve models of radiation tracks.

Plante, Ianik↗
DOE OSTI2024

Spectroscopic Analysis of Pu-bearing Compounds in Double-Walled Cells

Spectroscopic analysis of radiological materials has been historically limited to radiological labs with 11 older or less advanced scientific instrumentation. The development of double-walled cells (DWCs) at 12 the Savannah River National Laboratory (SRNL) has enabled Pu-bearing compounds to be removed 13 from radiological laboratories and studied in our radiologically clean spectroscopy lab with state-of14 the-art instrumentation. In this manuscript, we discuss the contributions of DWCs that have allowed 15 the application of Raman spectroscopy, diffuse reflectance infrared Fourier transform spectroscopy 16 (DRIFTS), diffuse reflectance spectroscopy (DRS) in the shortwave infrared, and gamma 17 spectroscopy at SRNL. Significant advances have been made in the understanding of thermal 18 decomposition of Pu(III) and Pu(IV) oxalates, the alpha-induced damage to the PuO2 crystal lattice, 19 and the effect of calcination temperatures to the quality of PuO2. These techniques have enabled 20 methods to conduct PuO2 age dating since last calcination and estimate the calcination temperature 21 with Raman and DRS. Additional spectroscopic information measured with DRIFTS has provided a 22 path to observe the evolution of carbon species with calcination temperature while gamma 23 spectroscopy provides information on age dating since last purification.

Villa-Aleman, Eliel↗
DOE OSTI2022

Chromosome evolution and the genetic basis of agronomically important traits in greater yam

The nutrient-rich tubers of the greater yam, Dioscorea alata L., provide food and income security for millions of people around the world. Despite its global importance, however, greater yam remains an orphan crop. Here, we address this resource gap by presenting a highly contiguous chromosome-scale genome assembly of D. alata combined with a dense genetic map derived from African breeding populations. The genome sequence reveals an ancient allotetraploidization in the Dioscorea lineage, followed by extensive genome-wide reorganization. Using the genomic tools, we find quantitative trait loci for resistance to anthracnose, a damaging fungal pathogen of yam, and several tuber quality traits. Genomic analysis of breeding lines reveals both extensive inbreeding as well as regions of extensive heterozygosity that may represent interspecific introgression during domestication. These tools and insights will enable yam breeders to unlock the potential of this staple crop and take full advantage of its adaptability to varied environments.

59 BASIC BIOLOGICAL SCIENCES↗