Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DRAG EFFECT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Interference drag in a simulated wing-fuselage juncture

The interference drag in a wing fuselage juncture as simulated by a flat plate and a body of constant thickness having a 1.5:1 elliptical leading edge is evaluated experimentally. The experimental measurements consist of mean velocity data taken with a hot wire at a streamwise location corresponding to 16 body widths downstream of the body leading edge. From these data, the interference drag is determined by calculating the total momentum deficit (momentum area) in the juncture and also in the two dimensional turbulent boundary layers on the flat plate and body at locations sufficiently far from the juncture flow effect. The interference drag caused by the juncture drag as measured at this particular streamwise station is -3% of the total drag due to the flat plate and body boundary layers in isolation. If the body is considered to be a wing having a chord and span equal to 16 body widths, the interference drag due to the juncture is only -1% of the frictional drag of one surface of such a wing.

Kubendran, L. R.↗
NASA NTRS1986

Transient induced drag

In the present treatment of the calculation of forces on a wing that is suddenly brought into motion at a constant speed, attention is given to the unsteady potential's contribution to the force balance. Total bound vorticity is produced at the initial impulse. The results obtained are independent of wing aspect ratio; as time increases, this effect on the drag force becomes smaller as the vortex emanating from the trailing edge is left behind. The second contributor to induced drag is the spanwise vorticity shedding that results from the spanwise load distribution of three-dimensional wings. This contribution grows with time as the length of the wake grows.

Weihs, D.↗
NASA NTRS1972

Effect of nozzle lateral spacing on afterbody drag and performance of twin-jet afterbody models with convergent-divergent nozzles at Mach numbers up to 2.2

Twin-jet afterbody models were investigated by using two balances to measure the thrust-minus-total drag and the afterbody drag, separately, at static conditions and at Mach numbers up to 2.2 for an angle of attack of 0 deg. Hinged-flap convergent-divergent nozzles were tested at subsonic-cruise- and maximum-afterburning-power settings with a high-pressure air system used to provide jet-total-pressure ratios up to 20. Two nozzle lateral spacings were studied, using afterbodies with similar interfairing shapes but with different longitudinal cross-sectional area distributions. Alternate, blunter, interfairings with different shapes for the two spacings, which produced afterbodies having identical cross-sectional area progressions corresponding to an axisymmetric minimum wave-drag configuration, were also tested. The results indicate that the wide-spaced configurations improved the flow field around the nozzles, thereby reducing drag on the cruise nozzles; however, the increased surface and projected cross-sectional areas caused an increase in afterbody drag. Except for a slight advantage with cruise nozzles at subsonic speeds, the wide-spaced configurations had the higher total drag at all other test conditions.

Pendergraft, O. C., Jr.↗
NASA NTRS1972

Effect of nozzle lateral spacing on afterbody drag and performance of twin-jet afterbody models with cone plug nozzles at Mach numbers up to 2.20

Twin-jet afterbody models were investigated by using two balances to measure separately the thrust minus total drag and the afterbody drag at Mach numbers of 0.0 and 0.50 to 2.20 for a constant angle of attack of 0. Translating shroud cone plug nozzles were tested at dry and maximum afterburning power settings with a high-pressure air system used to provide jet total-pressure ratios up to 20.0. Two nozzle lateral spacings were studied by using afterbodies with several interfairing shapes. The close- and wide-spaced afterbodies had identical cross-sectional area distributions when similar interfairings were installed on each. Nozzle cant angles of -5, 0, and 5 degrees were investigated. The results show that the highest overall performance was generally obtained with the close-spaced afterbody, basic interfairings (no base), and uncanted nozzles.

Berrier, B. L.↗
NASA NTRS1979

Effect of several airframe/nozzle modifications on the drag of a variable-sweep bomber configuration

A variable sweep bomber aircraft model was investigated to identify modifications for drag reduction. Modifications included simulated two dimensional nozzles, staggered and extended nozzles; short, long, and no interfairings between the nozzles; partial and complete wing-glove fairings; glove-fuselage sidefairing; fuselage underfairing; and wing pods. The variable wing sweep and variable exhaust nozzles of the scale model are discussed.

Re, R. J.↗
NASA NTRS1978

A procedure for the determination of the effect of fuselage nose bluntness on the wave drag of supersonic cruise aircraft

The incremental wave drag penalty due to nose blunting of a fuselage was investigated using a three dimensional finite difference scheme. An aircraft typical of current supersonic cruise concepts was considered. Computational problems with the finite difference scheme as the fuselage afterbody closes were addressed. A linear theory method was employed to compute the afterbody aerodynamics and effectively extends the finite difference scheme to closing afterbodies. Acceptable drag increments for various levels of nose bluntness were demonstrated using this approach.

Walkley, K. B.↗
NASA NTRS1931

The Effect of Slots and Flaps on the Lift and Drag of the Mcdonnell Airplanes Determined in Flight

This note contains the results of flight test conducted by the National Advisory Committee for Aeronautics on a low-wing monoplane equipped with leading-edge slots extending over the entire wing and flaps extending only to the ailerons, to find their effect on the lift and drag characteristics of the airplane. Curves are given showing the lift and drag characteristics of the airplane for the following conditions of the slots and flaps neutral; slots closed and flaps down; and slots open and flaps down. In addition, the high and low speed in level flight and the climbing characteristics are given. The results show that the slots used alone increase the maximum lift coefficient 54 per cent; the flaps alone increase it 38 per cent; and the slots and flaps in combination decrease the landing speed from 60 to 43 m.p.h.; increase the speed range of the airplane 40 per cent; and increase the glide angle at landing speed 4.2 degrees.

Soule, Hartley A↗