Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Cross Flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
NASA NTRS1971

Fabrication and testing of tungsten heat pipes for heat pipe cooled reactors.

The choice of chemically vapor deposited (CVD) tungsten as material for the heat pipes is based on studies reported by Busse et al. (1970). Aspects of pipe construction are discussed together with wick construction, and heat pipe operation. An auxiliary heater was used to overcome problems during the start of operation in the case of a thermally loaded pipe. Two heat pipes were operated at temperatures up to 1850 K. Annular and channeled wicks were investigated. The design of a cross flow heat exchanger is presented together with the design of a reactor heat pipe life test station.

Bacigalupi, R. J.↗
NASA NTRS1973

Effect of rotor design tip seed on aerodynamic performance of a model VTOL lift fan under static and crossflow conditions

Results are presented for a wind tunnel investigation of three single VTOL lift fan stages designed for the same overall total pressure ratio at different rotor tip speeds. The stages were tested in a model lift fan installed in a wing pod. The three stages had essentially the same aerodynamic performance along the operating line. However, differences in stage thrust characteristics were obtained when a variation in back pressure was imposed on the stages by cross-flow effects and thrust-vectoring louvers.

Stockman, N. O.↗
NASA NTRS1973

Space shuttle: Aerodynamic characteristics of a 162-inch diameter solid rocket booster with and without strakes

Tests conducted at NASA-Langley have shown that a small flap or strake can generate a significant amount of lift on a circular cylinder with large cross flow. If strakes are placed on the opposite sides and ends on a circular body, a moment will be produced about the center of mass of the body. The purpose of this test was to determine the static-aerodynamic forces and moments of a 162-inch diameter SRB (PRR) with and without strakes. The total angle-of-attack range of the SRB test was from -10 to 190 degrees. Model roll angles were 0, 45, 90, and 135 degrees with some intermediate angles. The Mach range was from 0.6 to 3.48. The 0.00494 scale model was designated as MSFC No. 449.

Johnson, J. D.↗
NASA NTRS1972

Analysis of an entrainment model of the jet in a crossflow

A theoretical model has been proposed for the problem of a round jet in an incompressible cross-flow. The method of matched asymptotic expansions has been applied to this problem. For the solution to the flow problem in the inner region, the re-entrant wake flow model was used with the re-entrant flow representing the fluid entrained by the jet. Higher order corrections are obtained in terms of this basic solution. The perturbation terms in the outer region was found to be a line distribution of doublets and sources. The line distribution of sources represents the combined effect of the entrainment and the displacement.

Chang, H. S.↗
NASA NTRS1973

Recovery of sounding rocket payloads by center-of-gravity position control.

A computerized procedure has been developed to predict dynamic pressure at parachute deployment altitude. Inputs to the program are payload geometry, center-of-gravity position, velocity, and altitude at start of reentry. Payload is assumed to be trimmed, and potential and cross-flow drag theory is used to compute trim angle-of-attack and trim drag coefficient as a function of free-stream Mach number. The computations involve only simple geometric quantities and closed-form equations. Payload flight path is assumed to be vertical, and equations of motion of the payload are integrated from start of reentry to chute deployment altitude.

Mcgarvey, J. F.↗
NASA NTRS1974

The effect of engine component noise on V/STOL aircraft noise contours

An analytical study of fly-over noise using noise contours to show the effects of varying airplane and path parameters. The method of approach was to synthesize engine component noise spectra and exercise these components along given flight paths to measure the individual and total fly-over effect as a function of noise footprint area. The study was carried out in two phases. Phase 1 utilized a research type aircraft and Phase 2 used an advanced VTOL aircraft. The effect of cross flow was considered for both inlet and exhaust sections of the engine.

Fogg, R. G.↗
NASA NTRS1975

Computational procedure for three-dimensional boundary layers on aircraft and aerospace vehicles

An implicit numerical procedure is developed to solve the full three-dimensional laminar, boundary layer equations over realistic aircraft and spacecraft configurations. This procedure utilizes splined functions in the direction normal to the surface and finite differences in the cross flow direction. Calculation of off-pitch plane attachment and detachment lines can be calculated. The solution procedure permits the incorporation of a wide variety of turbulent models and boundary conditions including; entropy layer procedures, specified surface temperatures or heat flux distributions, surface catalysis, mass addition, and the coupling to both three-dimensional inviscid codes and surface ablation codes. In addition, reasonable computing times are obtained.

Kendall, R. M.↗