SEARCH · Engineering Papers

Results for “Camber”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

All sources NASA NTRS DOE OSTI

NASA NTRS1980

Analytical investigation of aerodynamic characteristics of highly swept wings with separated flow

Many modern aircraft designed for supersonic speeds employ highly swept-back and low-aspect-ratio wings with sharp or thin edges. Flow separation occurs near the leading and tip edges of such wings at moderate to high angles of attack. Attempts have been made over the years to develop analytical methods for predicting the aerodynamic characteristics of such aircraft. Before any method can really be useful, it must be tested against a standard set of data to determine its capabilities and limitations. The present work undertakes such an investigation. Three methods are considered: the free-vortex-sheet method (Weber et al., 1975), the vortex-lattice method with suction analogy (Lamar and Gloss, 1975), and the quasi-vortex lattice method of Mehrotra (1977). Both flat and cambered wings of different configurations, for which experimental data are available, are studied and comparisons made.

Reddy, C. S.↗

NASA NTRS1979

Automatic mesh-point clustering near a boundary in grid generation with elliptic partial differential equations

Elliptic partial differential equations are used to generate a smooth grid that permits a one-to-one mapping in such a way that mesh lines of the same family do not cross. Problems that arise due to lack of clustering at crucial points or intersections of mesh lines at highly acute angles, are examined and various forcing or source terms are used (to correct the problems) that are either compatible with the maximum principle or are so locally controlled that mesh lines do not intersect. Attention is given to various schematics of unclustered grids and grid detail about (highly cambered) airfoils.

Steger, J. L.↗

NASA NTRS1980

Controlled supercritical crossflow on supersonic wings - An experimental validation

Leading edges of wings with high lift at supersonic speeds are discussed. Under these conditions, the leading edge must generate a controlled supercritical crossflow such that high lift is obtained without boundary layer separation. The leading edge concept that accomplishes this is the supersonic counterpart of the leading edge of the 2-D supercritical airfoil at transonic speeds. Wind tunnel test results on a cambered wing with a controlled supercritical crossflow leading edge successfully validated the concept. The main results are presented at the M = 1.62 design point, with off-design results given for the range of Mach numbers from 1.60 to 2.00. Surface pressure, oil flow photographs, and force data are presented and analyzed. A flat wing with the same thickness distribution was also tested and the results were used both for comparison with the designed wing and to illustrate the development of the supercritical crossflow region which, for the flat wing, is terminated by a distinct crossflow shock wave.

Mason, W. H.↗

NASA NTRS1980

Higher order farfield drag minimization for a subcritical wing design code

A higher order Trefftz plane model of the undistorted interacting wing wakes of two symmetric subsonic planforms has been developed and integrated with an existing vortex lattice wing design code. The Trefftz plane calculation provides continuous, piecewise quadratically varying bound circulations, which are then interpolated in the nearfield vortex lattice representation of the wing. Integration of the surface slopes for a specified chord loading function provides the design wing camber surfaces. This paper outlines the theoretical development and presents comparisons between results obtained using the present theory and (1) previous exact solutions for minimum induced drag and (2) previous wing designs obtained using a discrete vortex wake moded.

Kuhlman, J. M.↗

NASA NTRS1980

Theoretical and Experimental studies of aerodynamic interference effects

Theoretical studies of aerodynamic forces on winglets shed considerable light on the mechanism by which these devices can reduce drag at constant total lift and on the necessity for proper alignment and cambering to achieve optimum favorable interference. Results of engineering studies, wind tunnel tests and performance predictions are reviewed for installations proposed for the AMST YC-14 and the KC-135 airplanes. The other major area of aerodynamic interference discussed is that of engine nacelle installations. Slipper and overwing nacelles have received much attention because of their potential for noise reduction, propulsive lift and improved ground clearance. A major challenge is the integration of such nacelles with the supercritical flow on the upper surface of a swept wing in cruise at high subsonic speeds.

Rettie, I. H.↗

NASA NTRS1980

A study of wing body blending for an advanced supersonic transport

Increases in supersonic cruise lift drag ratio were sought at Mach numbers 2.2 and 2.7 using wing body planform and thickness blending. Constrained twist and camber optimization was performed in the presence of nacelles. Wing and fuselage thickness distributions were optimized for either minimum volume wave drag or minimum total pressure wave drag. The zero leading edge suction lift drag ratios were determined for three wing planforms. The magnitude of the effect of leading edge suction on attainable lift drag ratio was defined on one planform and estimation of available leading edge suction was made.

Goebel, T. P.↗

NASA NTRS1979

A higher order panel method for linearized supersonic flow

The basic integral equations of linearized supersonic theory for an advanced supersonic panel method are derived. Methods using only linear varying source strength over each panel or only quadratic doublet strength over each panel gave good agreement with analytic solutions over cones and zero thickness cambered wings. For three dimensional bodies and wings of general shape, combined source and doublet panels with interior boundary conditions to eliminate the internal perturbations lead to a stable method providing good agreement experiment. A panel system with all edges contiguous resulted from dividing the basic four point non-planar panel into eight triangular subpanels, and the doublet strength was made continuous at all edges by a quadratic distribution over each subpanel. Superinclined panels were developed and tested on s simple nacelle and on an airplane model having engine inlets, with excellent results.

Ehlers, F. E.↗

NASA NTRS1981

Aerodynamics, aeroelasticity, and stability of hang gliders. Experimental results

One-fifth-scale models of three basic ultralight glider designs were constructed to simulate the elastic properties of full scale gliders and were tested at Reynolds numbers close to full scale values. Twenty-four minor modifications were made to the basic configurations in order to evaluate the effects of twist, reflex, dihedral, and various stability enhancement devices. Longitudinal and lateral data were obtained at several speeds through an angle of attack range of -30 deg to +45 deg with sideslip angles of up to 20 deg. The importance of vertical center of gravity displacement is discussed. Lateral data indicate that effective dihedral is lost at low angles of attack for nearly all of the configurations tested. Drag data suggest that lift-dependent viscous drag is a large part of the glider's total drag as is expected for thin, cambered sections at these relatively low Reynolds numbers.

Kroo, I. M.↗

NASA NTRS1981

Factors Influencing the Predicted Performance of Advanced Propeller Designs

The assumptions on which conventional propeller aerodynamic performance analyses are based can be seriously violated when advanced high speed propellers are analyzed. Studies were performed using a lifting line representation for the propeller to determine the sensitivity of predicted propeller performance to various assumptions in the analysis. Items studied include the method of determining blade section lift and the effects of blade section drag, camber and blade sweep. The effects of nonuniform flow into the propeller and compressibility were also studied. Comparisons of analytical and experimental results are presented to demonstrate the overall validity of the results.

Bober, L. J.↗

NASA NTRS1981

Comparisons of AEROX computer program predictions of lift and induced drag with flight test data

The AEROX aerodynamic computer program which provides accurate predictions of induced drag and trim drag for the full angle of attack range and for Mach numbers from 0.4 to 3.0 is described. This capability is demonstrated comparing flight test data and AEROX predictions for 17 different tactical aircraft. Values of minimum (skin friction, pressure, and zero lift wave) drag coefficients and lift coefficient offset due to camber (when required) were input from the flight test data to produce total lift and drag curves. The comparisons of trimmed lift drag polars show excellent agreement between the AEROX predictions and the in flight measurements.

Axelson, J.↗

NASA NTRS1981

A discrete vortex method for the non-steady separated flow over an airfoil

A discrete vortex method was used to analyze the separated non-steady flow about a cambered airfoil. The foil flow modelling is based on the thin lifting-surface approach, where the chordwise location of the separation point is assumed to be known from experiments or flow-visualization data. Calculated results provided good agreement when compared with the post-stall aerodynamic data of two airfoils. Those airfoil sections differed in the extent of travel of the separation point with increasing angle of attack. Furthermore, the periodic wake shedding was analyzed and its time-dependent influence on the airfoil was investigated.

Katz, J.↗

NASA NTRS1981

Interactive multi-mode blade impact analysis

This paper describes the theoretical methodology used in developing an analysis for the response of turbine engine fan blades subjected to soft body (bird) impacts and the computer program that was developed using this methodology as its basis. This computer program is an outgrowth of two programs that were previously developed for the purpose of studying problems of a similar nature (a three-mode beam impact analysis and a multi-mode beam impact analysis). The present program utilizes an improved missile model that is interactively coupled with blade motion which is more consistent with actual observations. It takes into account local deformation at the impact area, blade camber effects, and the spreading of the impacted missile mass on the blade surface. In addition, it accommodates plate-type mode shapes. The analysis capability in this computer program represents a significant improvement in the development of the methodology for evaluating potential fan blade materials and designs with regard to foreign object impact resistance.

Alexander, A.↗

NASA NTRS1981

Rotating blade vibration analysis using shells

Shallow shell theory and the Ritz method are employed to determine the frequencies and mode shapes of turbomachinery blades having both camber and twist, rotating with non-zero angles of attack. Frequencies obtained for different degrees of shallowness and thickness are compared with results available in the literature, obtained from finite element analyses of nonrotating blades. Frequencies are also determined for a rotating blade, showing the effects of changing the (1) angular velocity of rotation, (2) disk radius and (3) angle of attack, as well as the significance of the most important body force terms.

Leissa, A. W.↗

NASA NTRS1980

HiMAT systems development results and projections

Significant findings of the Highly Maneuverable Aircraft Technology Remotely Piloted Research Vehicle (HiMAT RPRV) flight test program are presented. Among the topics covered are: aerodynamic scaling relationships, the aeroelastic tailoring of wing and canard twist and camber, and laminate graphite/epoxy composite primary structure performance under high-g loading maneuvers. Attention is also given to the set of actuators used in the test and development program, with a view to the minimization of costs through modularity and interchangeability of components and the extensive use of off-the-shelf equipment. The relationship between composite ply geometry and the shape and magnitude of aeroelastic deformations during maneuvering is discussed in detail.

Brown, L. E., Jr.↗

NASA NTRS1981

Factors influencing the predicted performance of advanced propeller designs

The assumptions on which conventional propeller aerodynamic performance analyses are based can be seriously violated when advanced high speed propellers are analyzed. Studies have been performed using a lifting line representation for the propeller to determine the sensitivity of predicted propeller performance to various assumptions in the analysis. Items which have been studied include the method of determining blade section lift and the effects of blade section drag, camber and blade sweep. The effects of nonuniform flow into the propeller and compressibility have also been studied. Comparisons of analytical and experimental results are presented to demonstrate the overall validity of the results.

Bober, L. J.↗

NASA NTRS1981

A continuous-vorticity panel method for lifting surfaces

A continuous-vorticity panel method is developed and utilized to predict the steady aerodynamic loads on lifting surfaces having sharp-edge separation. Triangular panels with linearly varying vorticity are used. The velocity field generated by an individual element is obtained in closed form. An optimization scheme is constructed for finding the vorticity at the nodes of the elements. The method is not restricted by aspect ratios, angles of attack, planforms, or camber. Rectangular and delta wings are presented as numerical examples. The numerical results are in good agreement with the experimental data for incompressible flows.

Yen, A.↗

NASA NTRS1948

Investigation of Effectiveness of Air-Heating a Hollow Steel Propeller for Protection Against Icing. 1: Unpartitioned Blades

An investigation to determine the effectiveness of icing protection afforded by air-heating hollow steel unpartitioned propeller blades has been conducted In the NACA Cleveland icing research tunnel. The propeller used was a production model modified with blade shank and tip openings to permit internal passage of heated air. Blade-surface and heated-air temperatures were obtained and photographic observations of Ice formations were made with variations In icing intensity and heating rate to the blades. For the conditions of Icing to which the propeller was subjected, it was found that adequate ice protection was afforded with a heating rate of 40 1 000 Btu per hour per blade. With less than 40,000 Btu per hour per blade, ice protection failed because of significant ice accretions on the leading edge. The chordwise distribution of heat was unsatisfactory with most of the available heat dissipated well back of the leading edge on both the thrust and camber face's instead of at the leading edge where it was most needed. A low utilization of available heat for icing protection is indicated by a beat-exchanger effectiveness of approximately 47 percent.

Mulholland, Donald R.↗

NASA NTRS1956

Experimental Droplet Impingement on Several Two-Dimensional Airfoils with Thickness Ratios of 6 to 16 Percent

The rate and area of cloud droplet impingement on several two-dimensional swept and unswept airfoils were obtained experimentally in the NACA Lewis icing tunnel with a dye-tracer technique. Airfoil thickness ratios of 6 to 16 percent; angles of attack from 0 deg to 12 deg, and chord sizes from 13 to 96 inches were included in the study. The data were obtained at 152 knots and are extended to other conditions by dimensionless impingement parameters. In general, the data show that the total and local collection efficiencies and impingement limits are primary functions of the modified inertia parameter (in which airspeed, droplet size, and body size are the most significant variables) and the airfoil thickness ratio. Local collection efficiencies and impingement limits also depend on angle of attack. Secondary factors affecting impingement characteristics are airfoil shape, camber, and sweep angle. The impingement characteristics obtained experimentally for the airfoils were within +/-10 percent on the average of the characteristics calculated from theoretical trajectories. Over the range of conditions studied, the experimental data demonstrate that a specific method can be used to predict the impingement characteristics of swept airfoils with large aspect ratios from the data for unswept airfoils of the same series.

Gelder, Thomas F.↗