Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CORROSION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

(Project 18-15531) Repair and Mitigation of Chloride-Induced Pitting and Chloride-Induced Stress Corrosion Cracking in Used Spent Nuclear Fuel Dry Cask Canister Materials (Final Technical Report)

Several experimental techniques were utilized to understand the corrosion and SCC performance of possible techniques for repairing cracks and pits in SS304 utilized for dry cask storage of spent nuclear fuel. The repairs examined included cold spray, FSW, soldering, and VFAW. The corrosion and SCC assessment techniques utilized for comparing repairs against the base material were 4-pt bending SCC testing in boiling MgCl 2 at stress levels between 0 MPa and 350 MPa, immersion testing in 40% RH brine solution meant to mimic a service-like environment, SSRT SCC testing in 40% RH brine solution. For FSW alone, scanning electrochemical cell microscopy and microelectrochemical syringe cell were utilized to understand the corrosion performance across the weld, in the retreating/advancing sides, and base material. Based on the results of this study, the FSW and cold spray repair techniques proved most viable for SCC repair in SS304 dry cask storage applications and continuing research is highly recommended to understand and quantify in further detail their SCC performance compared to unrepaired SS304. Additionally, solder and VFAW (patch or incline) would not be recommended based on the corrosion and SCC findings in this study.

42 ENGINEERING↗
DOE OSTI2025

Corrosion and Mechanical Durability Testing in High Temperature Molten Sulfur (CRADA Final Report)

The overall goal of the project is to explore and identify suitable candidate materials for high-temperature molten sulfur thermal energy storage (TES) operating up to a maximum temperature of 400°C–420°C for industrial process heat applications. A detailed corrosion and strength analysis of coupons subjected to long-term thermal testing in molten sulfur will be conducted to characterize the fundamental corrosion mechanism, corrosion rates, and mechanical durability. The results from the project contribute to the engineering design of sulfur TES systems with desired longevity and lower construction and maintenance costs. The research outcome benefits the TES research and development community by providing detailed corrosion and degradation information for more effective engineering design of the molten sulfur TES containment. It improves the diversity and reliability of the renewable technologies available for the U.S. industries and U.S. power grid.

14 SOLAR ENERGY↗
DOE OSTI2025

Hanford Double Shell Waste Tank Corrosion Studies- Final Report FY2024

For fiscal year (FY) 2024, the Savannah River National Laboratory (SRNL) focused on two experimental tasks related to Hanford Double Shell Tank (DST) chemistry and integrity. The first task focused on understanding risk of corrosion due to formation of either continuous layers or discrete patches of solids on the tanks’ inner sidewalls and bottoms. The objective of this task was to determine the effect of solid deposits on the corrosion risk to the tank bottom, and whether a combination of scale, saltcake and loose solids lead to under deposit corrosion. Electrochemical testing in a single cell arrangement was employed to determine a threshold inhibitor level for the interstitial liquid in the solids, above which carbon steel was not susceptible to corrosion beneath the solids. The inhibitor levels tested were based on the previously determined probability of failure for carbon steel in a simulated waste (i.e., Pitting Factor).

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

An Impedance-Loaded Surface Acoustic Wave Corrosion Sensor for Infrastructure Monitoring

Passive surface acoustic wave (SAW) devices are attractive candidates for continuous wireless monitoring of corrosion in large infrastructures. However, acoustic loss in the aqueous medium and limited read range usually create challenges in their widespread use for monitoring large systems such as oil and gas (O&G) pipelines, aircraft, and processing plants. This paper presents the investigation of impedance-loaded reflective delay line (IL-RDL) SAW devices for monitoring metal corrosion under O&G pipeline-relevant conditions. Specifically, we studied the effect of change in resistivity of a reflector on the backscattered signal of an RDL and investigated an optimal range through simulation. This was followed by the experimental demonstrations of real-time monitoring of Fe film corrosion in pressurized (550 psi) humid CO 2 conditions. Additionally, remote monitoring of Fe film corrosion in an acidic solution inside a 70 m carbon steel pipe was demonstrated using guided waves. This paper also suggests potential ways to improve the sensing response of IL-RDLs.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Near-Field Passive Wireless Sensor for High-Temperature Metal Corrosion Monitoring

This work focuses on the fabrication and evaluation of a passive wireless sensor for the monitoring of the temperature and corrosion of a metal material at high temperatures. An inductor–capacitor (LC) resonator sensor was fabricated through the screen printing of Ag-based inks on dense polycrystalline Al 2 O 3 substrates. The LC design was modeled using the ANSYS HFSS modeling package, with the LC passive wireless sensors operating at frequencies from 70 to 100 MHz. The wireless response of the LC was interrogated and received by a radio frequency signal generator and spectrum analyzer at temperatures from 50 to 800 °C in real time. The corrosion kinetics of the Cu 110 was characterized through thermogravimetric (TGA) analysis and microscopy images, and the oxide thickness growth was then correlated to the wireless sensor signal under isothermal conditions at 800 °C. The results showed that the wireless signal was consistent with the corrosion kinetics and temperature, indicating that these two characteristics can be further deconvoluted in the future. In addition, the sensor also showed a magnitude- and frequency-dependent response to crack/spallation events in the oxide corrosion layer, permitting the in situ wireless identification of these catastrophic events on the metal surface at high temperatures.

36 MATERIALS SCIENCE↗
NASA NTRS2003

An evaluation of microbial growth and corrosion of 316L SS in glycol/seawater mixtures

Glycol/seawater mixtures containing > 50% glycol inhibit corrosion of 316L stainless steel and do not support bacterial growth. The results indicate bacteria are able to use low concentrations of glycol (10%) as a growth medium, but bacterial growth decreased with increasing glycol concentration. Pitting potential, determined by anodic polarization, was used to evaluate susceptibility of 316L SS to corrosion in seawater-contaminated glycol. Mixture containing a minimum concentration of 50% propylene glycol-based coolant inhibited pitting corrosion. A slightly higher minimum concentration (55%) was needed for corrosion protection in ethylene glycol mixtures.

Biofilms/growth & development↗
NASA NTRS2017

Coatings for Oxidation and Hot Corrosion Protection of Disk Alloys

Increasing temperatures in aero gas turbines is resulting in oxidation and hot corrosion attack of turbine disks. Since disks are sensitive to low cycle fatigue (LCF), any environmental attack, and especially hot corrosion pitting, can potentially seriously degrade the life of the disk. Application of metallic coatings are one means of protecting disk alloys from this environmental attack. However, simply the presence of a metallic coating, even without environmental exposure, can degrade the LCF life of a disk alloy. Therefore, coatings must be designed which are not only resistant to oxidation and corrosion attack, but must not significantly degrade the LCF life of the alloy. Three different Ni-Cr coating compositions (29, 35.5, 45wt. Cr) were applied at two thicknesses by Plasma Enhanced Magnetron Sputtering (PEMS) to two similar Ni-based disk alloys. One coating also received a thin ZrO2 overcoat. The coated samples were also given a short oxidation exposure in a low PO2 environment to encourage chromia scale formation. Without further environmental exposure, the LCF life of the coated samples, evaluated at 760C, was less than that of uncoated samples. Hence, application of the coating alone degraded the LCF life of the disk alloy. Since shot peening is commonly employed to improve LCF life, the effect of shot peening the coated and uncoated surface was also evaluated. For all cases, shot peening improved the LCF life of the coated samples. Coated and uncoated samples were shot peened and given environmental exposures consisting of 500 hrs of oxidation followed by 50 hrs of hot corrosion, both at 760C). The high-Cr coating showed the best LCF life after the environmental exposures. Results of the LCF testing and post-test characterization of the various coatings will be presented and future research directions discussed.

LCF life↗
DOE OSTI2023

Carbon Corrosion in CO2 Electrolysis Systems

Driven by concerns over climate change, interest in CO2 conversion technologies has dramatically increased in recent years. By viewing CO2 as a readily available feedstock, many pathways for the production of carbon-neutral fuels and chemicals become available. In converting CO2, low carbon emitting energy sources must be used to ensure a low carbon footprint of the fuel and chemical products. The low-temperature electrochemical conversion of CO2 is a promising technology and allows for direct integration with renewable electricity sources. The development of low-temperature CO2 electrolysis technologies is informed by both PEM fuel cells and water electrolyzers, both of which are at a higher stage of development. However, CO2 electrolysis operates at a much higher cell voltage (-3V) than other low-temperature electrochemical processes, which can have implications for materials compatibility in the electrolyzer device. Carbon corrosion is of particular concern for the anode of CO2 electrolyzers, as a large driving force for corrosion exists due to the high required cell potentials. In this presentation, recent observations will be shared on carbon corrosion of the anode gas diffusion electrode (GDE) in low-temperature alkaline exchange membrane CO2 electrolysis. Results from ex-situ tests designed to isolate the carbon corrosion process for anode GDEs will be shared. These results will provide guidance on materials selection for CO2 utilization MEAs, which need to have a lifetime of several years to ensure industrial viability.

BIOMASS FUELS↗
DOE OSTI2020

Erosion-Corrosion Detection in Carbon Steel Pipe Loops using SRNLs Thickness and Mass Loss Measurement Coupons - 20464

Structural health of waste transfer infrastructure is of utmost importance to DOE and communities surrounding their active sites. A Fitness-for-Service (FFS) program for the Waste Transfer System has been implemented by the US Department of Energy (DOE) for the purposes of evaluating and quantifying the degradation of critical components. Currently, the method of approach is to section and evaluate pipelines that have been removed at end service. In order to augment data collection methods applied to making lifespan estimates of waste transfer system components, Florida International University (FIU) has been investigating new-technology based strategies for quantifying the rate of degradation. Present research considers the option of a coupon system installed on a section of pipe at points of interest that will provide easy access to high resolution measurements of erosion/corrosion rates during operation. Researchers at Savannah River National Laboratory (SRNL) have developed this novel solution for in situ erosion and corrosion measurements in many applicable locations such as tanks, pipes, ducts, and injection points. The coupons are approximately 12.7 mm (1/2 inch) in diameter and 25.4 mm (1 inch) in length and can be placed in the pipe sections using Swagelok compression fittings. The coupon design allows for monitoring of the total degradation resulting from corrosion and erosion. High-resolution Ultrasonic Thickness (UT) testing allows in-situ monitoring of both degradation mechanisms. When removed from the system mass loss resulting from corrosion and erosion may also be evaluated. Experimental testing at FIU implemented the SRNL coupon system in a 6.10 meter (20 foot) pipe loop system comprised of 50.8 mm (2 inch) and 76.2 mm (3 inch) pipe sections in order to replicate expected use cases at the sites. Operational conditions were emulated by pumping abrasive materials through the pipeline at full capacity and collecting measurements from the SRNL coupons. Initial testing was conducted by circulating water followed by a mixture of sand and water for uniform wear rates. Thickness changes and mass loss were measured, and the surface exposed to the process fluid was observed for visual evidence of characteristic wear patterns resulting from an erosive environment. The test matrix consisted of several hours of operation and using fine, medium and coarse grain sands. Test results were analyzed to check for all three parameters (mass loss/gain, thickness change and surface patters) which could provide estimates of the remaining useful life of the pipe sections. Thus, the research presents the findings of this evaluation of the SRNL coupons as a means for conducting high accuracy, cost effective in-situ analysis of pipeline and waste transfer systems for erosion and corrosion susceptibility. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Multi-Modal Characterization of Interfacial Corrosion of Ni-based Alloys in Chloride-based Molten Salts

The United States Department of Energy (DOE) is committed to the advancement of nuclear reactor technology through initiatives such as the Advanced Reactor Development Program (ARDP), to diversify the United States energy portfolio towards more sustainable energy options. The ARDP includes demonstration by industry partners of molten salt fast reactors (MSRs). Construction of molten salt reactor technology requires qualified nuclear structural materials. Unfortunately, there are no current materials that meet current qualification requirements dictated by the Nuclear Regulatory Commission for construction of MSRs. Adapting current structural material qualifications requires expansion of our current knowledgebase on corrosion performance. In this investigation, we assess microstructural changes in a Ni-based superalloy after exposure to a chloride-containing salt system through a correlated multi-modal approach combining several advanced characterization techniques. Namely we will highlight the impact of grain boundary phenomena at the onset of corrosion attack, including the role of intergranular crack propagation and development of internal corrosion products. The findings from this investigation will further expand our assessment of the corrosion performance of structural materials being investigated for construction of MSR components.

36 - MATERIALS SCIENCE↗
DOE OSTI2021

Sequestration and release of nitrite and nitrate in alkali-activated slag: A route toward smart corrosion control

Intercalating the corrosion inhibitive ions in hydrotalcite is a promising approach to improve the long-term efficiency of inhibitors in corrosion protection of steel in reinforced concrete. In this work, the potential of autogenously generating nitrite- and nitrate-intercalated hydrotalcite in alkali-activated slag (AAS) is investigated. The results show that the added nitrite and nitrate ions are preferably uptaken in the interlayer structure of hydrotalcite in AAS, and the sequestered nitrite and nitrate are released upon chloride exposure in seawater and NaCl solution. The incorporation of nitrite and nitrate has little detrimental effects on the chloride binding capacity of AAS but slightly enhances the chloride ingress due to the pore coarsening effect. Similar to ordinary Portland cement (OPC), AAS is more permeable to the chloride in seawater than NaCl solution. However, unlike the release of bound chloride contributed by ettringite formation in seawater-exposed OPC, the enhanced chloride ingress in seawater-exposed AAS is primarily attributed to the aggravated pH reduction at the exposure front due to brucite formation. This study contributes to the design of alkali-activated binders with a smart inhibitor releasing ability for mitigating corrosion of steel in concrete.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Corrosion susceptibility and chromium loss in Austenitic steels and Nickel-based alloys in molten FLiNaK at 700 °C

A comparative study was conducted to evaluate the corrosion susceptibility of 316L, 316H, Ni 200, Inconel 625, and Hastelloy N in molten FLiNaK at 700 °C for 100 h. Top-view and cross-sectional scanning electron microscopy (SEM) imaging, combined with energy-dispersive X-ray spectroscopy (EDS) mapping, was performed to investigate microstructural and compositional changes. SEM images were further processed by introducing a contrast threshold to map cavity distribution. Using EDS mapping, intergranular and intragranular Cr loss were separately characterized. The ranking of mass loss after corrosion, from highest to lowest, is as follows: 316H > 316L > Inconel 625 > Hastelloy N > Ni 200. Cr loss was found to be correlated with Mo concentration, in agreement with many previous studies, with higher Mo content resulting in reduced Cr loss. On the other hand, there is no evidence that the high carbon content in 316H enhances corrosion resistance. The relatively low solubility of carbon in austenite at the testing temperature limits the amount of dissolved carbon. Therefore, the carbon-retarded vacancy diffusion, and consequently the reduced Cr diffusion, were not observed.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2024

Operando carbon corrosion measurements in fuel cells using boron-doped carbon supports

Carbonaceous materials are the most common catalyst supports in proton exchange membrane fuel cell (PEMFCs), yet their corrosion is one of the limiting factors in achieving high durability. Herein, we doped carbon supports with boron (B) to increase the corrosion-resistance of the support. Two types of B-doped carbons were synthesized and studied as platinum support materials. Further, they varied in their morphologies, surface areas, and the types of boron species. The durability of Pt/B-doped carbon catalysts was investigated using the US-DOE catalysts’ supports accelerated stress test (AST) and a mass-spectrometer connected to the fuel cell effluent stream to quantify the mass of corroded carbon support in operando. The addition of boron to the carbon increased the stability of Pt catalysts in long-term usage of PEMFC. After 4000 AST cycles, more than 50% of initial current density was preserved for the boron-containing systems, while less than 30% of it remained with Vulcan carbon (Pt/V). Also, the Pt/B-doped carbon samples demonstrated better electrochemical active surface area (ECSA) stability when compared to Pt/V. Carbon loss measurements showed that B-doped carbons have higher resistance to electrochemical corrosion than unmodified carbon. Specifically, the substitutional boron-doped carbon demonstrated an extremely high stability and low corrosion rate.

25 ENERGY STORAGE↗
DOE OSTI2020

Localised instability of titanium during its erosion-corrosion in simulated acidic hydrometallurgical slurries

Electrochemical techniques were used to investigate the erosion-corrosion of titanium in simulated acidic mineral leaching slurries. Erosion-corrosion of titanium was caused by solid particle impingement. Electrochemical noise revealed that solid particle impacts resulted in localised fracture of the passive film, and erosion-corrosion of titanium proceeded in the form of current transients. As conditions become more abrasive, erosion-corrosion is an increasing threat to titanium equipment exposed to acidic slurries.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Ce post-treatment for increased corrosion resistance of AA2024-T3 anodized in tartaric-sulfuric acid

Here, the effect of a post-treatment for short time in 50 mM Ce(NO 3 ) 3 solution, with or without H 2 O 2 , on the corrosion of AA2024-T3 anodized in tartaric-sulfuric acid was investigated. Electrochemical (EIS, polarization curves) and corrosion (immersion) tests showed improved performance for samples post-treated at 50 °C in the H 2 O 2 containing solution. Microstructural characterization (SEM, STEM, GDOES) evidenced the presence of Ce oxyhydroxides both at the surface and within the pores of the anodized layer, and their preferential interaction with defective sites both at micro and nanoscale. Important amounts of Ce-species were found near corrosion products, indicating active corrosion protection by Ce ions.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Reverse martensitic transformation on the corrosion behavior of a 2304 lean duplex stainless steel

This study investigates the influence of the reverse martensitic transformation on the corrosion behavior of 2304 lean duplex stainless steel (LDSS) at low temperatures (400–600°C). The steel underwent cold rolling, followed by isochronal annealing for 0.5 h. Phase transformations and microstructures were analyzed using X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. Corrosion resistance was evaluated using a syringe cell with cyclic potentiodynamic polarization in 0.6 M NaCl solution and double-loop electrochemical potentiokinetic reactivation in 0.5 M H 2 SO 4 + 0.001 M KSCN solution. A bimodal breakdown potential behavior, associated with either pitting or transpassivity, was observed in the as-received (AR) and samples annealed at 400°C. Pitting in the AR sample was associated with Al–Mg–Si–Ca–O inclusions, while pitting on the samples annealed at 400°C was linked to local reduced passive film resistance. Severe cold rolling enhanced the pitting resistance of 2304 LDSS. Selective electrochemical etching revealed preferential corrosion at phase interfaces and within the austenite phase. Additionally, annealing at 500°C to 600°C led to a marked decrease in pitting resistance and increased sensitization. Electron backscatter diffraction analysis of the corroded pits in the annealed specimens indicated that pits tend to nucleate and grow in α'-martensite/austenite regions. Furthermore, the nanostructure formed during low-temperature reversion, characterized by dislocation-cell martensite with high dislocation density and stacking faults, may adversely affect corrosion resistance due to heterogeneities associated with alloying element redistribution.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Corrosion protection of steel pipelines with metal-polymer composite barrier liners

Pipelines are efficient in transporting natural gas over large distances. Wet carbon dioxide present in pipelines can create an environment that is corrosive to steel. Polymer liners made from either polyethylene or polyamide (nylon) are presently used to mitigate internal corrosion in natural gas pipelines. Gas diffuses through all polymers over time, and polymer-only liners lower the steel corrosion rate by reducing the reactive gas flux to the internal surface of a pipeline. Composite liners, which incorporate one or more metallic layers that are impermeable to corrosive gases, offer better protection than polymer-only liners. In this study, we measured the methane, water vapor, and carbon dioxide permeability of a multi-layer barrier film and found it to be more effective in resisting gas permeation than polyethylene and nylon-11 films.

03 NATURAL GAS↗
DOE OSTI2024

Corrosion protection of mild steel by superhydrophobic magnetite coating

Corrosion-resistant hydrophobic magnetite coatings on mild steel surfaces were developed by immersion method. The effect of steel surface roughness (R a ) on its hydrophobicity was systematically studied using contact angle measurement (CAM), scanning electron microscopy (SEM), and atomic force microscopy (AFM). The corrosion resistance of hydrophobic magnetite coatings was evaluated using a potentiodynamic polarization test. The durability of the coatings was assessed in air, tap water, and 3.5 wt% NaCl environments. Hydrophobic magnetite coating with a water contact angle of 146-152° showed excellent resistance to corrosion, longevity in atmospheric air, and significant self-cleaning properties. The primary focus of this study was to develop a quick and simple immersion technique to create hydrophobic surfaces on mild steel. Finally, results suggest that surface roughness plays a significant role in surface hydrophobicity, and enhancing the hydrophobicity of mild steel improves its corrosion resistance.

36 MATERIALS SCIENCE↗