Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CONE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Effects of rotor location, coning, and tilt on critical loads in large wind turbines

Several large (1500 kW) horizontal rotor configurations were analyzed to determine the effects on dynamic loads of upwind downwind rotor locations, coned and radial blade positions, and tilted and horizontal rotor axis positions. Loads were calculated for a range of wind velocities at three locations in the structure: (1) the blade shank; (2) the hub shaft; and (3) the yaw drive. Blade axis coning and rotor axis tilt were found to have minor effects on loads. However, locating the rotor upwind of the tower significantly reduced loads at all locations analyzed.

Spera, D. A.↗
NASA NTRS1977

Effects of rotor location, coning, and tilt on critical loads in large wind turbines

Three large (1500 kW) horizontal rotor configurations were analyzed to determine the effects on dynamic loads of upwind and downwind rotor locations, coned and radial blade positions, and tilted and horizontal rotor axis positions. Loads were calculated for a range of wind velocities at three locations in the structure: the blade shank, the hub shaft, and the yaw drive. Blade axis coning and rotor axis tilt were found to have little effect on loads. However, locating the rotor upwind of the tower significantly reduced loads at all locations analyzed.

Spera, D. A.↗
NASA NTRS1978

Solar concentrating properties of truncated hexagonal, pyramidal and circular cones

The solar concentrating properties of specularly reflecting truncated pyramidal, hexagonal, and circular cones are evaluated. Pyramidal and hexagonal configurations are discussed with reference to the concentration factor as a function of half apex angle and the length of the side over the width, and to the irradiance distribution. Expressions are derived for the concentration factor and the irradiance at the base of a circular cone when the sunlight is incident normal to the aperture and for oblique incidence.

Burkhard, D. G.↗
NASA NTRS1979

Laminar and turbulent flows over spherically blunted cone and hyperboloid with massive surface blowing

Numerical solutions are presented for the flow over a spherically blunted cone and hyperboloid with massive surface blowing. Time-dependent viscous shock-layer equations are used to describe the flow field. The boundary conditions on the body surface include a prescribed blowing-rate distribution. The governing equations are solved by a time-asymptotic finite-difference method. Results presented here are only for a perfect gas-type flow at zero angle of attack. Both laminar and turbulent flow solutions are obtained. It is found that the effect of the surface blowing on the laminar flow field is to smooth out the curvature discontinuity at the sphere-cone juncture point, which results in a positive pressure gradient over the body. The shock slope increases on the downstream portion of the body as the surface blowing rate is increased. The turbulent flow with surface blowing is found to redevelop a boundary-layer-like region near the surface. The effects of this boundary-layer region on the flow field and heating rates are discussed.

Kumar, A.↗
NASA NTRS1981

Cap protects aircraft nose cone

Inexpensive, easily fabricated cap protects aircraft nose cone from erosion. Made of molded polycarbonate, cap has been flight tested at both subsonic and supesonic speeds. Its strength and erosion characteristics are superior to those of fiberglass cones.

Bryan, C. F., Jr.↗
NASA NTRS1980

Heating rate measurements over 30 deg and 40 deg (half angle) blunt cones in air and helium in the Langley expansion tube facility

Convective heat transfer measurements, made on the conical portion of spherically blunted cones (30 deg and 40 deg half angle) in an expansion tube are discussed. The test gases used were helium and air; flow velocities were about 6.8 km/sec for helium and about 5.1 km/sec for air. The measured heating rates are compared with calculated results using a viscous shock layer computer code. For air, various techniques to determine flow velocity yielded identical results, but for helium, the flow velocity varied by as much as eight percent depending on which technique was used. The measured heating rates are in satisfactory agreement with calculation for helium, assuming the lower flow velocity, the measurements are significantly greater than theory and the discrepancy increased with increasing distance along the cone.

Reddy, N. M.↗
NASA NTRS1979

Laminar and turbulent flows over a spherically blunted cone with massive surface blowing

Numerical solutions are presented for the flow over a spherically blunted cone with massive surface blowing. Time-dependent viscous shock layer equations are used to describe the flowfield. The boundary conditions on the body surface include a prescribed blowing rate distribution. The governing equations are solved by a time-asymptotic finite-difference method. Results presented here are only for a perfect gas-type flow at zero angle of attack. Both laminar and turbulent flow solutions are obtained. It is found that the surface blowing smooths out the effect of the curvature discontinuity at the sphere-cone juncture point on the laminar flowfield and results in a negative pressure gradient over the body. The shock slope increases on the downstream portion of the body as the surface blowing rate is increased. The turbulent flow with surface blowing is found to redevelop a boundary-layer-like region near the surface. The effects of this boundary-layer-like region on the flowfield and heating rates are discussed.

Kumar, A.↗
NASA NTRS1980

A computational and experimental study of high Reynolds number viscous/inviscid interaction about a cone at high angle of attack

The flow over a 5 deg semi-angle cone at incidence in supersonic flow is studied as a model problem for the flow over aircraft forebodies. A computational method utilizing the conically symmetric Navier-Stokes equations is used to obtain theoretical flow results which are compared with experimental data from the Ames Research Center 6- by 6-Foot Wind Tunnel and with results from a cone model sting mounted on an F-15 aircraft. The computed results agree well with the wind-tunnel data but less well with the flight data. Modification of the algebraic turbulence model was necessary to reflect an apparent lower turbulence level in flight than was present in the wind tunnel.

Mcrae, D. S.↗
NASA NTRS1980

Equivalent-cone calculation of nitric oxide production rate during Space Shuttle re-entry

The amount of nitric oxide likely to be produced in the shock layer around a Space Shuttle orbiter vehicle during its reentry is calculated at one point on the trajectory. An equivalent-cone is defined as one that produces the same amount of nitric oxide as the orbiter. The amounts of nitric oxide produced by the cone are calculated at points along the trajectory to determine their total and altitudinal distribution. The results show that about 14 tonne nitric oxide is produced at each entry, the peak occurring at 68 km altitude.

Park, C.↗
NASA NTRS1981

Crossflow effects on steady and fluctuating pressures on an ogive-cylinder cone-frustum model in supersonic separated flow

Wind-tunnel tests were conducted on an ogive-cylinder model with two axisymmetric protuberances having cone frustum angles of cone = 23 deg and 45 deg that were used to generate detached shock waves and the resulting separated flow areas downstream of the shock. The tests were conducted in a 9 by 7 foot supersonic wind tunnel at a free-stream Mach number of 2.0 and at Reynolds numbers of 1.5 x 1 million and 3.9 x 1 million, based on body diameter. The model had an afterbody fineness ratio of 8.3, and the ogive nose had a fineness ratio of 3.0. Two characteristics of the fluctuating pressures in surface vortex flows that result from the crossflow component, (velocity along the tunnel longitudinal axis free stream angle of attack), in combination with changes in the longitudinal pressure gradient were measured: (1) the broadband, rms-pressure coefficients and (2) the power spectral densities. Measurements are presented for various flow regions on the model such as the attached turbulent boundary layer, the detached frustum shock wave, and separated flow areas. The results indicate that the pressure fluctuations around or in the neighborhood of the foci of the vortex flows had broadband intensities and power spectral densities nearly identical to the levels previously measured in separated-flow regions at angles of attack of 0 deg.

Dods, J. B., Jr.↗
NASA NTRS1981

Aerodynamic heating on the corrugated surface of a 10.2 deg half-angle blunted cone at Mach 6.7

A 10.2 deg half-angle blunted cone with corrugated surfaces was tested in the Langley 8-foot high-temperature structures tunnel to measure the aerodynamic heating of its surfaces. The tests were made in a turbulent boundary layer at angles of attack of 0 deg, 5 deg, and 10 deg. Heating of the windward side was in reasonable agreement with theoretical turbulent predictions for a smooth cone, while heating on the leeward side was between laminar and turbulent predictions as a result of local transitional flow or flow separation produced by high lee-side pressures. Localized heating measurements indicated a significant increase in heating at large cross-flow angles, with the maximum heating rates occurring where the flow reattaches on the upstream side of the corrugation crest and the minimum occurring on the downstream side where the flow is separated.

Weinstein, I.↗
NASA NTRS1982

Study of boundary-layer transition using transonic cone Preston tube data

Laminar layer Preston tube data on a sharp nose, ten degree cone obtained in the Ames 11 ft TWT and in flight tests are analyzed. During analyses of the laminar-boundary layer data, errors were discovered in both the wind tunnel and the flight data. A correction procedure for errors in the flight data is recommended which forces the flight data to exhibit some of the orderly characteristics of the wind tunnel data. From corrected wind tunnel data, a correlation is developed between Preston tube pressures and the corresponding values of theoretical laminar skin friction. Because of the uncertainty in correcting the flight data, a correlation for the unmodified data is developed, and, in addition, three other correlations are developed based on different correction procedures. Each of these correlations are used in conjunction with the wind tunnel correlation to define effective freestream unit Reynolds numbers for the 11 ft TWT over a Mach number range of 0.30 to 0.95. The maximum effective Reynolds numbers are approximately 6.5% higher than the normal values. These maximum values occur between freestream Mach numbers of 0.60 and 0.80. Smaller values are found outside this Mach number range. These results indicate wind tunnel noise affects the average laminar skin friction much less than it affects boundary layer transition. Data on the onset, extent, and end of boundary layer transition are summarized. Application of a procedure for studying the relative effects of varying nose radius on a ten degree cone at supercritical speeds indicates that increasing nose radius promotes boundary layer transition and separation of laminar boundary layers.

Reed, T. D.↗
NASA NTRS1982

Flight and wind-tunnel correlation of boundary-layer transition on the AEDC transition cone

Transition and fluctuating surface pressure data were acquired on a 10 deg included angle cone, using the same instrumentation and technique over a wide range of Mach and Reynolds numbers in 23 wind tunnels and in flight. Transition was detected with a traversing pitot-pressure probe in contact with the surface. The surface pressure fluctuations were measured with microphones set flush in the cone surface. Good correlation of end of transition Reynolds number RE(T) was obtained between data from the lower disturbance wind tunnels and flight up to a boundary layer edge Mach number, M(e) = 1.2. Above M(e) = 1.2, however, this correlation deteriorates, with the flight Re(T) being 25 to 30% higher than the wind tunnel Re(T) at M(e) = 1.6. The end of transition Reynolds number correlated within + or - 20% with the surface pressure fluctuations, according to the equation used. Broad peaks in the power spectral density distributions indicated that Tollmien-Schlichting waves were the probable cause of transition in flight and in some of the wind tunnels.

Fisher, D. L.↗
NASA NTRS1983

Flight and wind-tunnel correlation of boundary-layer transition on the AEDC transition cone

Transition and fluctuating surface pressure data were acquired on a 10 degree included angle cone, using the same instrumentation and technique over a wide range of Mach and Reynolds numbers in 23 wind tunnels and in flight. Transition was detected with a traversing pitot pressure probe in contact with the surface. The surface pressure fluctuations were measured with microphones set flush in the cone surface. Good correlation of end of transition Reynolds number Re (sub T) was obtained between data from the lower disturbance wind tunnels and flight up to a boundary layer edge Mach number, M (sub e) = 1.2. Above M (sub e) = 1.2, however, this correlation deteriorates, with the flight Re (sub T) being 25 to 30% higher than the wind tunnel Re (sub T) at M (sub e) = 1.6. The end of transition Reynolds number correlated within + or - 20% with the surface pressure fluctuations. Broad peaks in the power spectral density distributions indicated that Tollmien-Schlichting waves were the probable cause of transition in flight and in some of the wind tunnels.

Fisher, D. F.↗
NASA NTRS1983

Free-stream noise and transition measurements on a cone in a Mach 3.5 pilot low-disturbance tunnel

A small scale Mach 3.5 wind tunnel incorporating certain novel design features and intended for boundary-layer-transition research has been tested. The free stream noise intensities and spectral distributions were determined throughout the test section for several values of unit Reynolds number and for nozzle boundary layer bleed on and off. The boundary layer transition location on a slender cone and the response of this to changes in the noise environment were determined. Root mean square free stream noise levels ranged from less than one tenth up to values approaching those for conventional nozzles, with the lowest values prevailing at upstream locations within the nozzle. For low noise conditions, cone transition Reynolds numbers were in the range of those for free flight; whereas for high noise conditions, they were in the range of those in conventional tunnels.

Beckwith, I. E.↗
NASA NTRS1982

Electromagnetic cyclotron-loss-cone instability associated with weakly relativistic electrons

The amplification of fast extraordinary mode waves at frequencies very close to the electron cyclotron frequency, due to the presence of a population of energetic electrons with a loss-cone type distribution, is studied. Low-energy background electrons are included in the analysis. Two types of loss-cone distribution functions are considered, and it is found that the maximum growth rates for both distribution functions are of the same order of magnitude. When the thermal effects of the energetic electrons are included in the dispersion equation, the real frequencies of the waves are lower than those obtained by using the cold plasma approximation. This effect tends to enhance the growth rate. An idealized case including a parallel electric field such that the distribution function of the trapped energetic electrons is modified is also considered. It is assumed that the parallel electric field can remove the low-energy background electrons away from the source region of radiation. Both these effects increase the growth rate.

Wong, H. K.↗