Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Band gap”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

High-efficiency concentration/multi-solar-cell system for orbital power generation

An analysis was performed to determine the economic feasibility of a concentrating spectrophotovoltaic orbital electrical power generation system. In this system dichroic beam-splitting mirrors are used to divide the solar spectrum into several wavebands. Absorption of these wavebands by solar cells with matched energy bandgaps increases the cell efficiency while decreasing the amount of heat which must be rejected. The optical concentration is performed in two stages. The first concentration stage employs a Cassegrain-type telescope, resulting in a short system length. The output from this stage is directed to compound parabolic concentrators which comprise the second stage of concentration. Ideal efficiencies for one-, two-, three-, and four-cell systems were calculated under 1000 sun, AMO conditions, and optimum energy bands were determined. Realistic efficiencies were calculated for various combinations of Si, GaAs, Ge and GaP. Efficiencies of 32 to 33 percent were obtained with the multicell systems. The optimum system consists of an f/3.5 optical system, a beam splitter to divide the spectrum at 0.9 microns, and two solar cell arrays, GaAs and Si.

Onffroy, J. R.↗
NASA NTRS1995

Noncausal telemetry data recovery techniques

Cost efficiency is becoming a major driver in future space missions. Because of the constraints on total cost, including design, implementation, and operation, future spacecraft are limited in terms of their size power and complexity. Consequently, it is expected that future missions will operate on marginal space-to-ground communication links that, in turn, can pose an additional risk on the successful scientific data return of these missions. For low data-rate and low downlink-margin missions, the buffering of the telemetry signal for further signal processing to improve data return is a possible strategy; it has been adopted for the Galileo S-band mission. This article describes techniques used for postprocessing of buffered telemetry signal segments (called gaps) to recover data lost during acquisition and resynchronization. Two methods, one for a closed-loop and the other one for an open-loop configuration, are discussed in this article. Both of them can be used in either forward or backward processing of signal segments, depending on where a gap is specifically situated in a pass.

Tsou, H.↗
NASA NTRS1981

Cathodoluminescence of InP

Cathodoluminescence studies were carried out on p-type InP having carrier concentrations ranging from 7.2 x 10 to the 16th to 7.4 x 10 to the 18th per cu cm in the temperature range of 80-580 K. It was found that low-temperature spectra exhibited peaks at 1.41 and 1.38 eV. These peaks were attributed to band-to-band and band-acceptor transitions, respectively. The dependence of the band-to-band peak on temperature was used to extend knowledge of the temperature dependence of the energy gap of InP to 550 K. It was shown that the half-width of the cathodoluminescence peak can be used for the determination of carrier concentration and carrier-concentration inhomogeneities in the material. The variations of the cathodoluminescence peak height with temperature indicated the possibility of Auger recombination for high carrier concentrations (7.4 x 10 to the 18th per cu cm) at temperatures above 450 K.

Gatos, C. H.↗
NASA NTRS1984

Uncertainties about the physical electronics of n(+) and p(+) silicon, with applications for solar cells

After brief surveys of the significance of n(+) and p(+) silicon for the conversion efficiency of solar cells, the work in this paper is concentrated on uncertainties in the characterization of n(+) and p(+) regions. The topics treated include the quantum density states of the majority carrier band and the position of the Fermi level relative to the edge of this band, the resulting force field on the minority carriers accompanying a space dependence of the energy gap narrowing, and the interpretation of measurements of the energy gap narrowing and the minority carrier diffusivity and mobility. The treatment seeks to show how these uncertainties relate to solar cell design and to estimates of attainable conversion efficiency.

Lindholm, F. A.↗
NASA NTRS1991

Nonequilibrium radiative heating prediction method for aeroassist flowfields with coupling to flowfield solvers

A method for predicting radiation adsorption and emission coefficients in thermochemical nonequilibrium flows is developed. The method is called the Langley optimized radiative nonequilibrium code (LORAN). It applies the smeared band approximation for molecular radiation to produce moderately detailed results and is intended to fill the gap between detailed but costly prediction methods and very fast but highly approximate methods. The optimization of the method to provide efficient solutions allowing coupling to flowfield solvers is discussed. Representative results are obtained and compared to previous nonequilibrium radiation methods, as well as to ground- and flight-measured data. Reasonable agreement is found in all cases. A multidimensional radiative transport method is also developed for axisymmetric flows. Its predictions for wall radiative flux are 20 to 25 percent lower than those of the tangent slab transport method, as expected, though additional investigation of the symmetry and outflow boundary conditions is indicated. The method was applied to the peak heating condition of the aeroassist flight experiment (AFE) trajectory, with results comparable to predictions from other methods. The LORAN method was also applied in conjunction with the computational fluid dynamics (CFD) code LAURA to study the sensitivity of the radiative heating prediction to various models used in nonequilibrium CFD. This study suggests that radiation measurements can provide diagnostic information about the detailed processes occurring in a nonequilibrium flowfield because radiation phenomena are very sensitive to these processes.

Hartung, Lin C.↗
NASA NTRS2002

Fail-Safe Operation of a High-Temperature Magnetic Bearing Investigated for Gas Turbine Engine Applications

The Structural Mechanics and Dynamics Branch at the NASA Glenn Research Center has developed a three-axis high-temperature magnetic bearing suspension rig to enhance the safety of the bearing system up to 1000 F. This test rig can accommodate thrust and radial bearings up to a 22.84 cm (9 in.) diameter with a maximum axial loading of 22.25 kN (5000 lb) and a maximum radial loading up to 4.45 kN (1000 lb). The test facility was set up to test magnetic bearings under high-temperature (1100 F) and high-speed (20,000 rpm) conditions. The magnetic bearing is located at the center of gravity of the rotor between two high-temperature grease-packed mechanical ball bearings. The drive-end duplex angular contact ball bearing, which is in full contact, acts as a moment release and provides axial stability. The outboard end ball bearing has a 0.015-in. radial clearance between the rotor to act as a backup bearing and to compensate for axial thermal expansion. There is a 0.020-in. radial air gap between the stator pole and the rotor. The stator was wrapped with three 1-kW band heaters to create a localized hot section; the mechanical ball bearings were outside this section. Eight threaded rods supported the stator. These incorporated a plunger and Bellville washers to compensate for radial thermal expansion and provide rotor-to-stator alignment. The stator was instrumented with thermocouples and a current sensor for each coil. Eight air-cooled position sensors were mounted outside the hot section to monitor the rotor. Another sensor monitored this rotation of the outboard backup bearing. Ground fault circuit interrupts were incorporated into all power amplifier loops for personnel safety. All instrumentation was monitored and recorded on a LabView-based data acquisition system. Currently, this 12-pole heteropolar magnetic bearing has 13 thermal cycles and over 26 hr of operation at 1000 F.

Choi, Benjamin B.↗
NASA NTRS2006

Seamless tiled display system

A modular and scalable seamless tiled display apparatus includes multiple display devices, a screen, and multiple lens assemblies. Each display device is subdivided into multiple sections, and each section is configured to display a sectional image. One of the lens assemblies is optically coupled to each of the sections of each of the display devices to project the sectional image displayed on that section onto the screen. The multiple lens assemblies are configured to merge the projected sectional images to form a single tiled image. The projected sectional images may be merged on the screen by magnifying and shifting the images in an appropriate manner. The magnification and shifting of these images eliminates any visual effect on the tiled display that may result from dead-band regions defined between each pair of adjacent sections on each display device, and due to gaps between multiple display devices.

Dubin, Matthew B.↗
NASA NTRS1998

Development of SIS Mixers for 1 THz

SIS heterodyne mixer technology based on niobium tunnel junctions has now been pushed to frequencies over 1 THz, clearly demonstrating that the SIS junctions are capable of mixing at frequencies up to twice the energy gap frequency (4 Delta/h). However, the performance degrades rapidly above the gap frequency of niobium (2 Delta/h approx. 700 GHz) due to substantial ohmic losses in the on-chip tuning circuit. To solve this problem, the tuning circuit should be fabricated using a superconducting film with a larger energy gap, such as NbN; unfortunately, NbN films often have a substantial excess surface resistance in the submillimeter band. In contrast, the SIS mixer measurements we present in this paper indicate that the losses for NbTiN thin films can be quite low.

Zmuidzinas, J.↗
NASA NTRS2007

Aperture-Coupled Thin-Membrane L-Band Antenna

The upper part of the figure depicts an aperture-coupled L-band antenna comprising patterned metal conductor films supported on two thin polyimide membranes separated by an air gap. In this antenna, power is coupled from a microstrip line on the lower surface of the lower membrane, through a slot in a metal ground plane on the upper surface of the lower membrane, to a radiating metal patch on the upper surface of the upper membrane. The two-membrane configuration of this antenna stands in contrast to a three-membrane configuration heretofore considered as the basis for developing arrays of dual-polarization, wideband microwave antennas that could be thin and could be, variously, incorporated into, or supported on, thin structures, including inflatable structures. By reducing the number of membranes from three to two, the present design simplifies the problems of designing and fabricating such antennas or arrays of such antennas, including the problems of integrating such antennas or arrays with thin-membrane-mounted transmit/ receive modules. In addition, the use of aperture (slot) coupling eliminates the need for rigid coaxial feed pins and associated solder connections on thin membranes, making this antenna more mechanically reliable, relative to antennas that include coaxial feed pins. This antenna is designed for a nominal frequency of 1.26 GHz. The polyimide membranes are 0.05 mm thick and have a relative permittivity of 3.4. The radiating patch is square, 8.89 cm on each side. This radiating patch lies 1.27 cm above the ground plane. The feeding microstrip line is 0.12 mm wide and has a characteristic impedance of 50 . The aperture-coupling slot, etched in the ground plane, is 0.48 mm wide and 79.5 mm long. In order to maximize coupling, the microstrip line is extended beyond the middle of the slot by a length of 36 mm, which corresponds to a transmission- line electrical length of about a quarter wavelength. The other end of the microstrip line is transformed to a 50-Ohm coplanar waveguide line, which is used for connection to a transmit/receive module. Some plated-through vias are added to the outer conductors of the coplanar waveguide to suppress parallel-plate modes. The measured and calculated 10-dB-return-loss bandwidth of the antenna is 100 MHz. By eliminating the radiating patch and the upper membrane that supports it, and performing two other simple modifications, one can convert the two-membrane antenna described above to a paper-thin single-membrane antenna, shown in the lower part of the figure. One modification is to increase the slot length to 104.95 mm; the other is to extend the microstrip to 36.68 mm past the middle of the slot. With these modifications, the slot now becomes a half-wavelength radiator with a nearly omnidirectional radiation pattern. In one potential use, such a paper-thin antenna could be pasted on an automobile window to enable omnidirectional communication.

Huang, John↗
NASA NTRS2011

Cryogenic 160-GHz MMIC Heterodyne Receiver Module

A cryogenic 160-GHz MMIC heterodyne receiver module has demonstrated a system noise temperature of 100 K or less at 166 GHz. This module builds upon work previously described in Development of a 150-GHz MMIC Module Prototype for Large-Scale CMB Radiation (NPO-47664), NASA Tech Briefs, Vol. 35, No. 8 (August 2011), p. 27. In the original module, the local oscillator signal was saturating the MMIC low-noise amplifiers (LNAs) with power. In order to suppress the local oscillator signal from reaching the MMIC LNAs, the W-band (75 110 GHz) signal had to be filtered out before reaching 140 170 GHz. A bandpass filter was developed to cover 120 170 GHz, using microstrip parallel-coupled lines to achieve the desired filter bandwidth, and ensure that the unwanted W-band local oscillator signal would be sufficiently suppressed. With the new bandpass filter, the entire receiver can work over the 140 180-GHz band, with a minimum system noise temperature of 460 K at 166 GHz. The module was tested cryogenically at 20 K ambient temperature, and it was found that the receiver had a noise temperature of 100 K over an 8-GHz bandwidth. The receiver module now includes a microstrip bandpass filter, which was designed to have a 3-dB bandwidth of approximately 120-170 GHz. The filter was fabricated on a 3-mil-thick alumina substrate. The filter design was based on a W-band filter design made at JPL and used in the QUIET (Q/U Imaging ExperimenT) radiometer modules. The W-band filter was scaled for a new center frequency of 150 GHz, and the microstrip segments were changed accordingly. Also, to decrease the bandwidth of the resulting scaled design, the center gaps between the microstrip lines were increased (by four micrometers in length) compared to the gaps near the edges. The use of the 150-GHz bandpass filter has enabled the receiver module to function well at room temperature. The system noise temperature was measured to be less than 600 K (at room temperature) from 154 to 168 GHz. Additionally, the use of a W-band isolator between the receiver module and the local oscillator source also improved the noise temperature substantially. This may be because the mixer was presented with a better impedance match with the use of the isolator. Cryogenic testing indicates a system noise temperature of 100 K or less at 166 GHz. Prior tests of the MMIC amplifiers alone have resulted in a system noise temperature of 65.70 K in the same frequency range (.160 GHz) when cooled to an ambient temperature of 20 K. While other detector systems may be slightly more sensitive (such as SIS mixers), they require more cooling (to 4 K ambient) and are not as easily scalable to build a large array, due to the need for large magnets and other equipment. When cooled to 20 K, this receiver module achieves approximately 100 K system noise temperature, which is slightly higher than single-amplifier module results obtained at JPL (65.70 K when an amplifier is corrected for back-end noise contributions). If this performance can be realized in practice, and a scalable array can be produced, the impact on cosmic microwave background experiments, astronomical and Earth spectroscopy, interferometry, and radio astronomy in general will be dramatic.

Samoska, Lorene A.↗
NASA NTRS2012

Effect of Spectrally Varying Albedo of Vegetation Surfaces on Shortwave Radiation Fluxes and Aerosol Direct Radiative Forcing

This study develops an algorithm for representing detailed spectral features of vegetation albedo based on Moderate Resolution Imaging Spectrometer (MODIS) observations at 7 discrete channels, referred to as the MODIS Enhanced Vegetation Albedo (MEVA) algorithm. The MEVA algorithm empirically fills spectral gaps around the vegetation red edge near 0.7 micrometers and vegetation water absorption features at 1.48 and 1.92 micrometers which cannot be adequately captured by the MODIS 7 channels. We then assess the effects of applying MEVA in comparison to four other traditional approaches to calculate solar fluxes and aerosol direct radiative forcing (DRF) at the top of atmosphere (TOA) based on the MODIS discrete reflectance bands. By comparing the DRF results obtained through the MEVA method with the results obtained through the other four traditional approaches, we show that filling the spectral gap of the MODIS measurements around 0.7 micrometers based on the general spectral behavior of healthy green vegetation leads to significant improvement in the instantaneous aerosol DRF at TOA (up to 3.02Wm(exp -2) difference or 48% fraction of the aerosol DRF, .6.28Wm(exp -2), calculated for high spectral resolution surface reflectance from 0.3 to 2.5 micrometers for deciduous vegetation surface). The corrections of the spectral gaps in the vegetation spectrum in the near infrared, again missed by the MODIS reflectances, also contributes to improving TOA DRF calculations but to a much lower extent (less than 0.27Wm(exp -2), or about 4% of the instantaneous DRF). Compared to traditional approaches, MEVA also improves the accuracy of the outgoing solar flux between 0.3 to 2.5 micrometers at TOA by over 60Wm(exp -2) (for aspen 3 surface) and aerosol DRF by over 10Wm(exp -2) (for dry grass). Specifically, for Amazon vegetation types, MEVA can improve the accuracy of daily averaged aerosol radiative forcing in the spectral range of 0.3 to 2.5 micrometers at equator at the equinox by 3.7Wm(exp -2). These improvements indicate that MEVA can contribute to regional climate studies over vegetated areas and can help to improve remote sensing-based studies of climate processes and climate change.

Zhu, L.↗
NASA NTRS2018

Investigations of Hail Damage Swaths Using Various Satellite Remote Sensing Platforms

Severe thunderstorms that bring damaging winds and large hail can cause significant damage to agricultural crops. Severe thunderstorms can cause upwards of several hundreds of millions of dollars in damage to agricultural areas. Formal ground surveys are not conducted on these areas of damage, like they are for suspected tornado damaged areas. IF ground surveys were conducted, they would likely be time and resources consuming due to their large spatial extent. Satellite remote sensing has been frequently used in identification and analysis of these hail damage swaths. Previous analysis have looked at the simple change in damaged vegetation to looking at the damage areas in satellite imagery with varying spatial resolutions. One study has even looked at the impacts that these damage swaths can have on the land surface, associated fluxes and how they affect numerical weather prediction. Previous studies have focused on using optical remote (VIS, NIR, SWIR) sensing instruments and derived indices, such as Normalized Difference Vegetation Index (NDVI) for analysis. NDVI is used to monitor the health (greenness) of the vegetation. Optical sensors however are limited by sky conditions over the areas they are imaging and certain bands are further limited by the diurnal cycle. These limitations can lead to sometimes upwards of 7 to 10 day gaps of the surface not being imaged, especially during the height of summer convection. One way to obtain more views of the surface, regardless of the sky conditions or time of day is through the use of synthetic aperture radar (SAR). SAR sensors are active instruments that transmit in the microwave portion of the EM spectrum. The surface and its characteristics will determine the amount of energy scattered back to the sensor. The SAR sensors then measure amplitude and phase of wavelength coming back from surface.

Bell, Jordan R.↗
NASA NTRS1995

Optimization of GaN thin films via MOCVD

A unique characteristic of every semiconductor is the amount of energy required to break an electron bond in the lowest band of allowed states, the valence band. The energy necessary to set an electron free and allow it to conduct in the material is termed the energy gap (Eg). Semiconductors with wide bandgap energies have been shown to possess properties for high power, high temperature, radiation resistance damage, and short wavelength optoelectronic applications. Gallium nitride, which has a wide gap of 3.39 eV, is a material that has demonstrated these characteristics. Various growth conditions are being investigated for quality gallium nitride heteroepitaxy growth via the technique of low pressure metal organic chemical vapor deposition (MOCVD) that can be used for device development.

Dickens, Corey↗
NASA NTRSDate not supplied

Development of the GeoNEX Level 2G Products: Exploiting the Diurnal Variability of TOA Reflectance in Atmospheric Correction

This study develops a new atmospheric correction algorithm to generate the Level 2G products, in particular the gap-filled Surface Reflectance at 10-minute time steps, for the Geostationary-NASA Earth Exchange (GeoNEX) project. The algorithm is based on the MODIS MAIAC (Multi-Angle Implementation of Atmospheric Correction) framework but with significant modifications to exploit angular/temporal information from the diurnal variability of the GeoNEX L1G TOA (Top-of-Atmosphere) reflectance. The algorithm starts by evaluating the roughness/smoothness of the diurnal time series of the TOA reflectance. Because rapid changes in TOA reflectance are generally caused by passing clouds or shadows, rough segments of the time series are automatically filtered out while the smooth segments are further tested for brightness and temperature to identify clear-sky and snow-free observations. Next the algorithm runs the MAIAC RTM (Radiative Transfer Model) to retrieve the Ross-Thick-Li-Sparse (RTLS) BRDF model parameters and the daily-mean atmospheric optical depth (AOD) that allow the RTM to optimally simulate the observed diurnal variability of clear-sky TOA reflectance. Once the initial RTLS parameters are retrieved after the algorithm’s burn-in period, they are used as the prior information to predict the AOD level for the next days, while the subsequent clear-sky observations are used to make necessary adjustments to the RTLS parameters in an continuous fashion. This “prediction-analysis” cycle is then iterated to process the full time series of the L1G data, skipping only total-cloudy days or when surface snow is detected. We tested the algorithm over a list of selected AERONET sites. The retrieved results (the daily mean AOD and the RTLS parameters) reasonably agree with the ground-based measurements. Importantly, the results indicate that the diurnal cycles of surface reflectance are continuous functions of the illumination-view geometry. Thus we can use the retrieved RTLS model to accurately fill in data gaps on partial cloudy days. Also, our algorithm is totally independent from the traditional approaches based on the use of spectral band ratios between the shortwave infrared (e.g., 2.2µm) and the visible (e.g., 0.47µm and 0.64µm) bands. Our results thus demonstrate that the high-frequent diurnal geostationary observations contain unique information that helps us improve atmospheric correction of remote sensing data.

GeoNEX↗
NASA NTRS2012

Polarimetric Imaging of Large Cavity Structures in the Pre-transitional Protoplanetary Disk Around PDS 70: Observations of the Disk

We present high resolution H-band polarized intensity (PI; FWHM = 0."1: 14 AU) and L'-band imaging data (FWHM = 0."11: 15 AU) of the circumstellar disk around the weak-lined T Tauri star PDS 70 in Centaurus at a radial distance of 28 AU (0."2) up to 210 AU (1."5). In both images, a giant inner gap is clearly resolved for the first time, and the radius of the gap is approx.70 AU. Our data show that the geometric center of the disk shifts by approx.6 AU toward the minor axis. We confirm that the brown dwarf companion candidate to the north of PDS 70 is a background star based on its proper motion. As a result of SED fitting by Monte Carlo radiative transfer modeling, we infer the existence of an optically thick inner disk at a few AU. Combining our observations and modeling, we classify the disk of PDS 70 as a pre-transitional disk. Furthermore, based on the analysis of L'-band imaging data, we put an upper limit mass of companions at approx.30 to approx.50MJ within the gap. Taking account of the presence of the large and sharp gap, we suggest that the gap could be formed by dynamical interactions of sub-stellar companions or multiple unseen giant planets in the gap. Subject headings: planetary systems - protoplanetary disks - stars: individual (PDS 70) - stars: pre-main sequence - polarization

Hashimoto, J.↗
NASA NTRS2020

A Roadmap for High-Resolution Satellite Soil Moisture Applications - Confronting Product Characteristics with User Requirements

Soil moisture observations are of broad scientific interest and practical value for a wide range of applications. The scientific community has made significant progress in estimating soil moisture from satellite-based Earth observation data, particularly in operationalizing coarse-resolution (25-50 km) soil moisture products. This review summarizes existing applications of satellite-derived soil moisture products and identifies gaps between the characteristics of currently available soil moisture products and the application requirements from various disciplines. We discuss the efforts devoted to the generation of high-resolution soil moisture products from satellite Synthetic Aperture Radar (SAR) data such as Sentinel-1 C-band backscatter observations and/or through downscaling of existing coarse-resolution microwave soil moisture products. Open issues and future opportunities of satellite-derived soil moisture are discussed, providing guidance for further development of operational soil moisture products and bridging the gap between the soil moisture user and supplier communities.

Jian Peng↗
NASA NTRS1993

Breaking Kelvin-Helmholtz waves and cloud-top entrainment as revealed by K-band Doppler radar

Radars have occasionally detected breaking Kelvin-Helmholtz (KH) waves under clear-air conditions in the atmospheric boundary layer and in the free troposphere. However, very few direct measurements of such waves within clouds have previously been reported and those have not clearly documented wave breaking. In this article, we present some of the most detailed and striking radar observations to date of breaking KH waves within clouds and at cloud top and discuss their relevance to the issue of cloud-top entrainment, which is believed to be important in convective and stratiform clouds. Aircraft observations reported by Stith suggest that vortex-like circulations near cloud top are an entrainment mechanism in cumuliform clouds. Laboratory and modeling studies have examined possibility that KH instability may be responsible for mixing at cloud top, but direct observations have not yet been presented. Preliminary analyses shown here may help fill this gap. The data presented in this paper were obtained during two field projects in 1991 that included observations from the NOAA Wave Propagation Laboratory's K-band Doppler radar (wavelength = 8.7 mm) and special rawinsonde ascents. The sensitivity (-30 dBZ at 10 km range), fine spatial resolution (375-m pulse length and 0.5 degrees beamwidth), velocity measurement precision (5-10 cm s-1), scanning capability, and relative immunity to ground clutter make it sensitive to non-precipitating and weakly precipitating clouds, and make it an excellent instrument to study gravity waves in clouds. In particular, the narrow beam width and short pulse length create scattering volumes that are cylinders 37.5 m long and 45 m (90 m) in diameter at 5 km (10 km) range. These characteristics allow the radar to resolve the detailed structure in breaking KH waves such as have been seen in photographic cloud images.

Martner, Brooks E.↗