Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Axial flow compressor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

Investigation of Unsteady Flow Behavior in Transonic Compressor Rotors with LES and PIV Measurements

In the present study, unsteady flow behavior in a modern transonic axial compressor rotor is studied in detail with large eddy simulation (LES) and particle image velocimetry (PIV). The main purpose of the study is to advance the current understanding of the flow field near the blade tip in an axial transonic compressor rotor near the stall and peak-efficiency conditions. Flow interaction between the tip leakage vortex and the passage shock is inherently unsteady in a transonic compressor. Casing-mounted unsteady pressure transducers have been widely applied to investigate steady and unsteady flow behavior near the casing. Although many aspects of flow have been revealed, flow structures below the casing cannot be studied with casing-mounted pressure transducers. In the present study, unsteady velocity fields are measured with a PIV system and the measured unsteady flow fields are compared with LES simulations. The currently applied PIV measurements indicate that the flow near the tip region is not steady even at the design condition. This self-induced unsteadiness increases significantly as the compressor rotor operates near the stall condition. Measured data from PIV show that the tip clearance vortex oscillates substantially near stall. The calculated unsteady characteristics of the flow from LES agree well with the PIV measurements. Calculated unsteady flow fields show that the formation of the tip clearance vortex is intermittent and the concept of vortex breakdown from steady flow analysis does not seem to apply in the current flow field. Fluid with low momentum near the pressure side of the blade close to the leading edge periodically spills over into the adjacent blade passage. The present study indicates that stall inception is heavily dependent on unsteady behavior of the flow field near the leading edge of the blade tip section for the present transonic compressor rotor.

Hah, Chunill↗

End-wall boundary layer prediction for axial compressors

An integral boundary layer procedure was developed for the computation of viscous and secondary flows along the annulus walls of an axial compressor. The procedure is an outgrowth and extension of the pitch-averaged methods of Mellor and Horlock. In the present work secondary flow theory is used to develop approximations for the velocity profiles inside a rotating blade row and for the blade force deficit terms in the momentum integral equations. The computer code based on this procedure was iteratively coupled to a quasi-one-dimensional model for the external inviscid flow. Computed results are compared with measurements in a compressor cascade.

Sockol, P. M.↗

End-wall boundary layer prediction for axial compressors

An integral boundary layer procedure has been developed for the computation of viscous and secondary flows along the annulus walls of an axial compressor. The procedure is an outgrowth and extension of the pitch-averaged methods of Mellor and Horlock. In the present work secondary flow theory is used to develop approximations for the velocity profiles inside a rotating blade row and for the blade force deficit terms in the momentum integral equations. The computer code based on this procedure has been iteratively coupled to a quasi-one-dimensional model for the external inviscid flow. Computed results are compared with measurements in a compressor cascade.

Sockol, P. M.↗

An algebraic RNG-based turbulence model for three-dimensional turbomachinery flows

An algebraic eddy viscosity turbulence model based on Renormalization Group (RNG) theory for complex three-dimensional turbomachinery flows is presented. Modifications are made to the baseline RNG model for wakes and separated flows. The model has several advantages over popular algebraic models most notably its lack of empirically determined coefficients. The model is used to compute the mean flow in a low speed axial compressor rotor. The agreement with blade boundary layer and radial flow experimental data is very good and shows improvement over the Baldwin-Lomax model. The development of the tip leakage vortex is also well predicted. The computed wake decay also compares favorably with recent experimental data.

Kirtley, K. R.↗

Duct liner optimization for turbomachinery noise sources

An acoustical field theory for axisymmetric, multisectioned lined ducts with uniform flow profiles was combined with a numerical minimization algorithm to predict optimal liner configurations having one, two, and three sections. Source models studied include a point source located on the axis of the duct and rotor/outlet-stator viscous wake interaction effects for a typical research compressor operating at an axial flow Mach number of about 0.4. For this latter source, optimal liners for equipartition-of energy, zero-phase, and least-attenuated-mode source variations were also calculated and compared with exact results. It is found that the potential benefits of liner segmentation for the attenuation of turbomachinery noise is greater than would be predicted from point source results. Furthermore, effective liner design requires precise knowledge of the circumferential and radial modal distributions.

Lester, H. C.↗

Refining the W1 and SE1 Facilities

The Engine Research Building (ERB) houses more than 60 test rigs that study all aspects of engine development. By working with Mary Gibson in the SE1 and W1A Turbine Facilities, I became aware of her responsibilities and better acquainted with the inner workings of the ERB. The SE1 Supersonic/Subsonic Wind Tunnel Facility contains 2 small wind tunnels. The first tunnel uses an atmospheric inlet, while the second uses treated 40-psig air. Both of the tunnels are capable of subsonic and supersonic operation. An auxiliary air supply and exhaust piping providing both test sections with suction, blowing, and crossfire capabilities. The current configuration of SE1 consists of a curved diffuser that studies the blockage along the endwalls. The W1A Low Speed Compressor Facility provides insight for the complex flow phenomena within its 4-stage axial compressor, sand the data obtained from W 1A is used to develop advanced models for fluid dynamic assessment. W1A is based off of a low speed research compressor developed by GE in the 1950's. This compressor has a removable casing treatment under rotor 1, which allows for various tip treatment studies. The increased size and low speed allows instrumentation to be located in the compressor s complex flow paths. Air enters the facility through a filtered roof vent, conditioned for temperature and turbulence, and then passed through the compressor W1A is described as a dynamic facility with many projects taking place simultaneously. This current environment makes it challenging to follow the various affairs that are taking place within the area. During my first 4 weeks at the NASA Glenn Research Center, I have assisted Mary Gibson in multiple tasks such as facility documents, record keeping, maintenance and upgrades. The facility has lube systems for its gearbox and compressor. These systems are critical in the successful operation of the facility. I was assigned the task of creating a facility estimate list, which included the filters and strainers required for the compressor. For my remaining time spent here, we expect to complete a facility parts listing and a virtual project summary so that W1A and SE1 will become ergonomic facilities that will make it easier for people to observe the capabilities and history of the area and the employees that operate. Bolstering our efforts in achieving these goal are the online technical tutorials, software such as Microsoft Excel. Macromedia Flash MX Macromedia Dreamweaver MX, Photoshop 6.0 and the assistance of several NASA employees.

Chambers, Rodney D.↗

Altitude Operational Characteristics of Prototype J40-WE-8 Turbojet Engine

The altitude operational characteristics of the prototype J40-WE-8 turbojet engine were determined in the NACA Lewis altitude wind tunnel. The operational characteristics that were obtained include (1) compressor surge characteristics, (2) acceleration and deceleration rates, (3) steady-state windmilling-engine characteristics, (4) altitude ignition characteristics, and (5) the effect of two grades of fuel on steady-state engine performance at an altitude of 45,000 feet and a flight Mach number of 0.20. The altitude ignition characteristics determined include the effects of (1) ignition fuel flow, (2) two ignition procedures, (3) fuel temperatures, and (4) two grades of fuel on ignition characteristics. The compressor surge line, when presented as a function of compressor pressure ratio and corrected engine speed, was not affected by changes in flight condition and was independent of engine-inlet installation and of the manner in which surge was approached, rapidly or slowly. Also there was no effect of altitude or engine-inlet installation on the compressor surge recovery line when presented as a function of compressor pressure ratio and corrected engine speed.

FUELS - RELATION TO ENGINE PERFORMANCE↗

Summary of 65-Series Compressor-Blade Low-Speed Cascade Data by Use of the Carpet-Plotting Technique

The carpet-plotting technique is presented in this paper as a more useful and concise method of summarizing cascade data on the NACA 65-series compressor blades given in NACA Technical Note 3916. Carpet plots included permit the selection of the blade camber and the design angle of attack required to fulfill a design vector diagram. Other carpet plots provide means for the prediction of off-design turning angles. Also presented are carpet plots of an isentropic pressure-rise coefficient as a entering Mach number.

COMPRESSORS - AXIAL-FLOW↗

Systematic two-dimensional cascade tests of NACA 65-series compressor blades at low speeds

A two-dimensional low-speed porous-wall cascade tunnel investigation has been conducted to establish the performance of the NACA 65-series compressor blade sections over the useful range of inlet angle, solidity, and section camber. Design points for optimum high-speed operation are presented. The loading limitation is determined for some conditions. Trends of section operating range with increasing section camber are determined for the four inlet angles tested.

COMPRESSORS - AXIAL-FLOW↗

Effect of design over-all compressor pressure ratio division on acceleration characteristics of three hypothetical two-spool turbojet engines

The engines, each with a compressor overall total-pressure ratio of 12 and a design inner-turbine-inlet temperature of 2500 degrees R, were investigated at static sea-level conditions to determine the effect on transient performance of varying the desitn pressure ratio divisions 2-6, 3-4, and 4-3 between the outer and inner compressors. The transient considered was an acceleration from 40 to 100 percent design thrust. When the outer compressor of each engine reached design speed, the inner compressors were overspeeding, the maximum being only 1.7 over design mechanical speed. Acceleration times for the three engines were equal.

TURBINES - MATCHINE↗

Compressibility and Turbulence Effects Due to Airfoil Clocking in Axial Compressors

Axial compressors have inherently unsteady flow fields because of relative motion between rotor and stator airfoils. This relative motion leads to viscous and inviscid (potential) interactions between blade rows. As the number of stages increases in a turbomachine, the buildup of convected wakes can lead to progressively more complex wake/wake and wake/airfoil interactions. Variations in the relative circumferential positions of stators or rotors can change these interactions, leading to different unsteady forcing functions on airfoils and different compressor efficiencies. In addition, as the Mach number increases the interaction between blade rows is intensified due to potential effects. The current study uses an unsteady, two-dimensional Navier-Stokes approach to investigate the unsteady aerodynamics of stator clocking in a 1-1/2 stage compressor, typical of high-pressure compressors used in advanced commercial jet engines. The effects of turbulence are modeled with both algebraic and two-equation models. Results include surface pressures, efficiencies, boundary layer quantities and turbulence quantities. In addition, the growth of turbulence and the effects of compressibility on airfoil are discussed.

Dorney, Daniel J.↗

The response of an axial compressor to unsteady disturbances

The disturbances of flow in a uniform duct are examined, taking into account a disturbance which is sinusoidal in time. The equations of motion for a plane disturbance with blade forces represented by body forces are considered along with the stage configuration of the compressor and the temperature rise for two-dimensional flow through the stage. An investigation is conducted for the case in which the disturbances are restricted to small amplitudes about the design operating condition for all points within the compressor. The three independent solutions of the disturbance equations obtained for the system of compressor and associated inlet and exit ducts can be used with three arbitrary constants to satisfy three external conditions.

Rannie, W. D.↗

Task II: Three-dimensional Rotating Stall Inception and Effects of Rotating Tip Clearance Asymmetry in Axial Compressors

The effects of two types of flow non-uniformity on stall inception behavior were assessed with linearized stability analyses of two compressor flow models. Response to rotating tip clearance asymmetries induced by a whirling rotor shaft or rotor height variations were investigated with a two-dimensional flow model. A 3-D compressor model was also developed to study the stability of both full-span and part-span rotating stall modes in annular geometries with radial flow variations. The studies focussed on (1) understanding what compressor designs were sensitive to these types of circumferential and spanwise flow non-uniformities, and (2) situations where 2-D stability theories were inadequate because of 3-D flow effects. Rotating tip clearance non-uniformity caused the greatest performance loss for shafts whirling at the rotating stall frequency. A whirling shaft displacement of 1 percent chord caused the stalling mass flow to rise by as much as 10 percent and the peak pressure rise to decrease by 6 percent. These changes were an order of magnitude larger than for equivalent-sized stationary or rotor-locked clearance asymmetries. Spanwise flow non-uniformity always destabilized the compressor, so that 2-D models over-predicted that stall margin compared to 3-D theory. The difference increased for compressors with larger spanwise variations of characteristic slope and reduced characteristic curvature near the peak. Differences between 2-D and 3-D stall point predictions were generally unacceptable (2 - 4 percent of flow coefficient) for single-stage configurations, but were less than 1 percent for multistage compressors. 2-D analyses predicted the wrong stall mode for specific cases of radial inlet flow distortion, mismatching and annulus area contraction, where higher-order radial modes led to stall. The stability behavior of flows with circumferential or radial non-uniformity was unified through a single stability criterion. The stall point for both cases was set by the integral around the annulus of the pressure rise characteristic slope, weighted by the amplitude of the mode shape. For the case of steady circumferential variations, this criterion reduced to the integrated mean slope (IMS) condition associated with steady inlet distortions. The rotating tip clearance asymmetry model was also used to demonstrate the feasibility of actively controlling the shaft position to suppress rotating stall. In axisymmetric mean flow, this method only stabilized the first harmonic mode, increasing the operating range until surge or higher harmonic modes became unstable.

Suder, Kenneth↗

System Study for Axial Vane Engine Technology

The purpose of this engine feasibility study was to determine the benefits that can be achieved by incorporating positive displacement axial vane compression and expansion stages into high bypass turbofan engines. These positive-displacement stages would replace some or all of the conventional compressor and turbine stages in the turbine engine, but not the fan. The study considered combustion occurring internal to an axial vane component (i.e., Diesel engine replacing the standard turbine engine combustor, burner, and turbine); and external continuous flow combustion with an axial vane compressor and an axial vane turbine replacing conventional compressor and turbine systems.

Badley, Patrick R.↗

A viscous-inviscid interactive compressor calculations

A viscous-inviscid interactive procedure for subsonic flow is developed and applied to an axial compressor stage. Calculations are carried out on a two-dimensional blade-to-blade region of constant radius assumed to occupy a mid-span location. Hub and tip effects are neglected. The Euler equations are solved by MacCormack's method, a viscous marching procedure is used in the boundary layers and wake, and an iterative interaction scheme is constructed that matches them in a way that incorporates information related to momentum and enthalpy thicknesses as well as the displacement thickness. The calculations are quasi-three-dimensional in the sense that the boundary layer and wake solutions allow for the presence of spanwise (radial) velocities.

Johnston, W.↗

A viscous-inviscid interactive compressor calculation

A viscous-inviscid interactive procedure for subsonic flow is developed and applied to an axial compressor stage. Calculations are carried out on a two-dimensional blade-to-blade region of constant radius assumed to occupy a mid-span location. Hub and tip effects are neglected. The Euler Equations are solved by MacCormack's method, a viscous marching procedure is used in the boundary layers and wake, and an iterative interaction scheme is constructed that matches them in a way that incorporates information related to momentum and enthalpy thicknesses as well as the displacement thickness. The calculations are quasi-three-dimensional in the sense that the boundary layer and wake solutions allow for the presence of spanwise (radial) velocities.

Johnston, W. A.↗

Secondary vorticity in axial compressor blade rows

A theoretical investigation of secondary flow in compressor blade rows is presented. Formulas for calculating secondary flows in annular cascade blade passages are derived. The influence of the relative rotation vector on secondary velocity perturbations, using recent developments in shear-flow theory, is examined. A method of calculating the flow through successive blade rows is given and a comparison is made with experimental results.

Dixon, S. L.↗