Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “zirconia”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

High Temperature Thick Film Sensor Development Based on Refractory Oxide Semiconductors

Solid-state, high-temperature sensing devices are required for accurate temperature, strain/stress, and failure monitoring for a range of advanced manufacturing, transportation, and military applications. High temperature conditions limit sensing strategies, where typically traditional metal and semiconductor materials are unstable, and the sensing options are limited to optical spectroscopy methods. In addition, strategies to embed the sensors directly within active components and protective thermal refractory are of interest that permit near-environment sensing which is not possible with the traditional electronic materials and components. Rare-earth chromite semiconductors exhibit some properties of interest for high temperature sensing technologies, such as: high microstructure and chemical stability, relatively high electronic conductivity at high temperatures, and relative thermal expansion coefficient matching to refractory thermal protective insulation (such as high-zirconia and -alumina ceramics). In this work, n-type and p-type doped lanthanum chromites compositions were computationally modelled and prepared, and the electrical, thermoelectric, and thermomechanical properties were measured for the obtained material systems. A few compositions were then processed into thick film health and temperature sensors and tested at high temperatures. To establish relative stability under harsh environment conditions, post- mortem microstructure and chemical composition was characterized after extended and cycle testing at high temperatures.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2024

Development of High Temperature (>700°C) Molten Salt Pump Technology for Generation 3 Solar Power Tower Systems

Bearings are required for long-shafted pumps historically used in concentrating solar thermal power applications. For molten chloride salts, bearings for such service conditions are not commercially available, nor has a design been demonstrated to work. Therefore, a project was sponsored by the Department of Energy’s Solar Energy Technologies Office for the development and demonstration of a submerged bearing for use in chloride salt pumps. This project’s tasks covered the tribological testing of candidate materials and the design, fabrication, testing, and post-test analysis of full-scale salt-compatible bearings. This work expands upon previous work. The effects of potential particulate in the salt were investigated through tribological bench testing. Through 11 tests, the MgO particulate size and concentration in a molten chloride salt were varied, and the effects on friction, wear rate, and wear characteristics were recorded. Novel journal bearings for chloride salt service were designed and fabricated based on these results. The bearings were of a relevant scale (i.e., for a 1.5 in. pump shaft) to demonstrate the technology with respect to further scale-up. The bearings were made of Haynes 244 and Yttria Partially Stabilized Zirconia. A custom bearing test rig, salt tanks, and associated infrastructure (e.g., heaters, tanks, transfer lines, gas flow control) were designed, procured, and installed. A few issues were encountered in the system fabrication process, resulting in delay of the project schedule. The system was successfully fabricated and assembled. Heating, cover gas, and pump motor systems were integrated into the control logic. This progress of the bearing test system represents a significant step forward towards demonstrating this promising technology. Nevertheless, the project ended before testing of the full-scale bearings could be performed.

14 SOLAR ENERGY↗
DOE OSTI2025

Status of the Fuel Fragment Dispersal Studies at Oak Ridge National Laboratory

During a loss-of-coolant accident, a nuclear fuel rods undergo balloon and burst. High burnup fuel is known to fragment and pulverize leading to the potential for the fuel to disperse through the burst opening either during the initial burst or following the burst during the reflood event. This milestone summarizes the design and assembly of a system to study dispersal in a postburst event. Surrogate fuel material (HfO 2 , tungsten, and yttria-stabilized zirconia [YSZ]) dispersing from as-burst loss-of-coolant accident (LOCA) test specimens was extensively investigated, along with dispersal of actual nuclear fuel following a LOCA Severe Accident Test Station (SATS) test.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Blending as an In-Tank Waste Processing Strategy: Year 1 Progress Report

The Hanford Site stores approximately 56 million gallons of radioactive legacy defense waste in underground tanks. Direct feed of southeast quadrant tank waste to a high-level waste treatment facility is currently being explored to accelerate tank treatment activities. This study seeks to de-risk waste transfers by favorably altering the resuspension and critical velocities of wastes through strategic waste blending. Wastes rich in aluminum- and zirconium-bearing solids pose significant risks due to their high settled strength and density. A series of tests explores how solid phase particle size and suspending phase chemistry alter waste transport properties, quantified through the just-suspended mixing speed (NJS), for pure and blended aluminum- and zirconium-bearing waste solid simulants. The study utilizes a range of gibbsites (three sizes spanning 10 to 90 µm) and zirconia solids (three sizes spanning 10 to 100 µm). As expected, the NJS of pure solids largely follows predictions based on literature correlations; blends of gibbsite and zirconium-bearing solids of differing particle sizes exhibit NJS maxima attributed to dense packing of the mixed-size settled solids. The findings of this study will assist in developing strategies to optimize the transport of waste solids for the safe and efficient delivery of tank waste.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Status of the Fuel Fragment Dispersal Studies at Oak Ridge National Laboratory

During a loss-of-coolant accident, a nuclear fuel rods undergo balloon and burst. High burnup fuel is known to fragment and pulverize leading to the potential for the fuel to disperse through the burst opening either during the initial burst or following the burst during the reflood event. This milestone summarizes the design and assembly of a system to study dispersal in a postburst event. Surrogate fuel material (HfO2, tungsten, and yttria-stabilized zirconia [YSZ]) dispersing from as-burst loss-of-coolant accident (LOCA) test specimens was extensively investigated, along with dispersal of actual nuclear fuel following a LOCA Severe Accident Test Station (SATS) test. Surrogate material tests spanned a variety of burst geometries, particle types, particle size distributions, and rod oscillation loadings (frequency and amplitude combinations).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

FCET Solid Oxide Fuel Cell Testing and Development (CRADA 526) (Final Report)

Pacific Northwest National Laboratory (PNNL) tested electrolyte coatings from Fuel Cell Enabling Technologies, Inc. (FCET) for use in solid oxide fuel cells (SOFCs). The key technology held by FCET is a process to deposit thin layers of oxide materials, less than 1 μm in thickness. The range of possible materials that can be deposited with their method is broad, but this project focused on the gadolinium-doped ceria (GDC) and yttria-stabilized zirconia (YSZ) electrolytes for SOFCs. Thin, gas tight electrolyte membranes have been a long-sought target in SOFC research. The thinner the electrolyte, the lower the cell resistance, and the higher performance of the cell (or the lower the operating temperature). A YSZ thickness of 1 μm would be a step change from the state-of-the-art, tape-cast electrolytes (~10 μm). An in-house prototype SOFC stack from FCET was first tested. The sealing geometry of the prototype stack was determined to be problematic, and testing shifted to button cells. Anode-supported solid oxide electrolysis cell (SOEC) button cells without an electrolyte layer were produced at PNNL and sent to FCET for coating with electrolyte. Three cells were tested with a gadolinium-doped ceria (GDC) electrolyte applied via spin coating. GDC was chosen for its conductivity at lower temperatures than YSZ. All three cells failed during initial reduction under hydrogen at 600°C. Testing then shifted to YSZ, which is the standard SOFC electrolyte. Several button cells were coated with YSZ and examined with scanning electron microscopy (SEM). A promising coating of ~1 mm thickness was observed under SEM. A similarly coated button cell was tested and failed similarly to previous tests during reduction at 600°C. The YSZ coating appeared dense and uniform in SEM analysis. The roughness of the underlying Ni/YSZ anode is on the order of 1 μm, and that may have compromised the gas-tightness of the coating. Further development is warranted to understand and refine the coating process. Thin YSZ applied via this spin-coating technique could be used as a low-cost, drop-in replacement in large-scale SOFC manufacturing processes, improving cell performance and lowering the cost per watt of SOFCs.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2025

Durable, Ultra-Thin Diaphragms for Liquid Alkaline Water Electrolysis

W. L. Gore & Associates assembled a world class team (De Nora Tech, LLC; New York University; and thyssenkrupp nucera) to develop durable, ultra-low resistance diaphragms that dramatically improve system efficiency, dynamic response, and operational flexibility. To enable the use of ultra-thin diaphragms, an optimized electrode package was chosen as part of an electrode down select study. Ultra-thin diaphragms based on microporous polymer scaffolds imbibed with zirconia nanoparticles were developed and tested. Performance and durability on par with incumbent materials was demonstrated. A transparent electrolyzer to directly observe in-situ diaphragm-bubble interactions was designed and built, and simultaneous optical and electrochemical performance tests were performed. A Pressurized Alkaline Water Electrolysis (PAWE) single cell test station was designed to support advanced R&D in high-pressure electrolysis, particularly for evaluating novel electrode and separator configurations under elevated temperature and pressure operating conditions. Due to early project termination, the original scope could not be fully achieved.

08 HYDROGEN↗
DOE OSTI2025

Validation of a Custom Ball-on-Ring Apparatus and Consideration of Common Issues for Use in Further Testing (SULI Deliverables)

Ceramic materials are well-known for their high hardness and strength but are limited in their application due to low toughness and sudden failure. As a potential solution, inspiration can be taken from dental enamel nanostructure, where undulating rods cause cracks to branch or deflect, increasing the energy needed to cause total fracture of a ceramic part. Following the dental enamel structure, a novel ceramic which uses 3D printed Yttria stabilized Zirconia rods in an alumina matrix was developed. To test this bio-inspired ceramic material, a proper testing apparatus needed to be created and tested to verify its accuracy. For this project, a bespoke ball on ring testing apparatus was created and tested using both conventionally sintered alumina disks and purchased alumina disks to validate its accuracy. By comparing the Weibull distribution of rupture strengths measured by the tests to literature values, it was shown that the testing frame had a wide distribution of strength which did not align with literature values on the lower end. Through fractography, it was found that some samples fractured from the contact stress induced by the ball indenter, which could not be used to calculate rupture strength. This fracture was often linked to low stress to failure, which was initiated by a flaw on the surface near the indenter which acted as a stress concentrator. Removal of these samples from the data set increased the accuracy of the reported rupture strength values for the ceramic. Considering the equations for the magnitude of contact and flexural strength, along with observations of initiating flaws, several measures can be taken for testing the bio-inspired composite. These measures include proper polishing of both sides of the sample, reducing sample thickness, and potentially using a softer indenter material.

36 - MATERIALS SCIENCE↗
DOE OSTI2024

Cellulose crystallinity index (CrI) of switchgrass measured by solid-state NMR

Here we present a curated dataset of switchgrass cellulose crystallinity index (CrI) measured using solid state nuclear magnetic resonance (NMR) spectroscopy. Seventy-two topline switchgrass lines grown in greenhouse were collected and ground to -20/+80 mesh. The switchgrass was then Soxhlet-extracted with toluene/ethanol for 24 h to remove extractives. The extractives-free switchgrass was holopulped by using peracetic acid at 5 g loading per g biomass and the solution consistency was adjusted to 5% with DI water. Holopulping was conducted at room temperature for 24 h with stirring. The obtained holocellulose was washed excessively with DI water and air-dried at room temperature for 24 h. The dried holocellulose was treated with hydrochloric acid (2.5 M) for 2 h to remove hemicellulose. The isolated cellulose was collected by filtration, rinsed with DI water, and used to analyze cellulose crystallinity by solid-state NMR. The NMR samples were prepared by packing the moisturized cellulose into 4-mm cylindrical Zirconia MAS rotors. Cross polarization/magic angle spinning (CP/MAS) NMR analysis of cellulose was carried out on a Bruker Avance III 400-MHz spectrometer operating at 100.59 MHz for 13C in a Bruker double-resonance MAS probe head at spinning speeds of 8 kHz. The CP/MAS experiments utilized a 5 ms (90°) proton pulse, 1.5 ms contact pulse, 4 s recycle delay and 4000 scans. The cellulose crystallinity index was determined from the areas of the cellulose crystalline C4 signal (δ 86-92 ppm) over the entire C4 regions (δ 79-92 ppm) in the NMR spectra.

Cellulose, crystallinity index, switchgrass, solid↗
DOE OSTI2023

Magnesium production by molten salt electrolysis with liquid tin cathode and multiple effect distillation

Low-cost clean primary production of magnesium metal is important for its use in many applications, from light-weight structural components to energy technologies. This work describes new experiments and cost and emissions analysis for a magnesium metal production process. The process combines molten salt electrolysis of MgO using MgF₂-CaF₂ electrolyte and a reactive liquid tin cathode, with gravity-driven multiple effect thermal system (G-METS) distillation to separate out the magnesium product, and re-use of the tin. Electrolysis experiments with carbon anodes showed current yield above 90%, while a yttria-stabilized zirconia solid oxide membrane (SOM) anode experiment showed 84% current yield. G-METS distillation is an important component of the envisioned process. It can potentially lower costs and energy use considerably compared with conventional magnesium distillation. Techno-economic analysis including detailed mass and energy balances shows that this electrolyte composition could lower costs by utilizing CaO, which is the primary impurity in MgO, as the Hall-Héroult process uses the sodium impurity in alumina. Analysis options include: raw material types (magnesite rock vs. brine or seawater), drying and calcining using electricity vs. natural gas, and carbon vs. SOM anode type. Using SOM inert anodes results in a cost premium around 10%–15%, mostly due to higher electrical energy usage resulting from membrane resistance, and reduces GHG emissions by approximately 1 kg CO₂/kg Mg product. Capital and operating cost estimates, and cradle to gate greenhouse gas (GHG) emissions analysis under several raw material and process technology scenarios, show comparable costs and emissions to those of aluminum production.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Degradation Comparison of Cyclic and Linear Siloxane Contamination on Solid Oxide Fuel Cells Ni-YSZ Anode

The solid oxide fuel cell (SOFC) nickel-yttria stabilized zirconia (Ni-YSZ) anode degradation due to different types of siloxane contamination is investigated. A cyclic structure siloxane, octamethylcyclotetrasiloxane (D4), and a linear structure siloxane, decamethyltetrasiloxane (L4), are mixed with H 2 +N 2 as the fuel for SOFCs at 750°C. The electrochemical characterization results after stability experiments suggest that the SOFC contaminated with cyclic siloxane, D4, had higher degradation. Pure YSZ pellets with different surface hydroxylation extents were also tested to investigate the D4/L4 adsorption and deposition process. Postmortem SEM/WDS, XRD and Raman analysis all indicate that cyclic siloxane has more deposition than linear siloxane on the anode. Further analysis demonstrates that high adsorption and low desorption rates of cyclic siloxane on YSZ are linked to the degradation. Besides the silicon deposition, SiC and amorphous carbon deposition were also observed from the XRD and Raman analysis.

25 ENERGY STORAGE↗
DOE OSTI2020

Femtosecond Laser Additive Manufacturing of Multi-Material Layered Structures

Laser additive manufacturing (LAM) of a multi-material multi-layer structure was investigated using femtosecond fiber lasers. A thin layer of yttria-stabilized zirconia (YSZ) and a Ni–YSZ layer were additively manufactured to form the electrolyte and anode support of a solid oxide fuel cell (SOFC). A lanthanum strontium manganite (LSM) layer was then added to form a basic three layer cell. This single step process eliminates the need for binders and post treatment. Parameters including laser power, scan speed, scan pattern, and hatching space were systematically evaluated to obtain optimal density and porosity. This is the first report to build a complete and functional fuel cell by using the LAM approach.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Understanding Selectivity in CO2 Hydrogenation to Methanol for MoP Nanoparticle Catalysts Using In Situ Techniques

Molybdenum phosphide (MoP) catalyzes the hydrogenation of CO, CO2, and their mixtures to methanol, and it is investigated as a high-activity catalyst that overcomes deactivation issues (e.g., formate poisoning) faced by conventional transition metal catalysts. MoP as a new catalyst for hydrogenating CO2 to methanol is particularly appealing for the use of CO2 as chemical feedstock. Herein, we use a colloidal synthesis technique that connects the presence of MoP to the formation of methanol from CO2, regardless of the support being used. By conducting a systematic support study, we see that zirconia (ZrO2) has the striking ability to shift the selectivity towards methanol by increasing the rate of methanol conversion by two orders of magnitude compared to other supports, at a CO2 conversion of 1.4% and methanol selectivity of 55.4%. In situ X-ray Absorption Spectroscopy (XAS) and in situ X-ray Diffraction (XRD) indicate that under reaction conditions the catalyst is pure MoP in a partially crystalline phase. Results from Diffuse Reflectance Infrared Fourier Transform Spectroscopy coupled with Temperature Programmed Surface Reaction (DRIFTS-TPSR) point towards a highly reactive monodentate formate intermediate stabilized by the strong interaction of MoP and ZrO2. This study definitively shows that the presence of a MoP phase leads to methanol formation from CO2, regardless of support and that the formate intermediate on MoP governs methanol formation rate.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Mechanical and Tribological Performance of Additively Manufactured Nanocrystalline Aluminum via Cryomilling and Cold Spray

In this study, nanocrystalline (NC) aluminum (Al) and magnesium (Mg)-doped Al bulk components were fabricated using a hybrid manufacturing process that combines cryomilling and high-pressure cold spray (HPCS) additive deposition techniques. Yttria-stabilized zirconia (YSZ) was also added during the HPCS process to improve deposition efficiency and build-up thickness via peening. The evolution of morphology, crystallite size, and elemental composition of both cryomilled powders and cold-sprayed (CS’ed) components was systematically characterized using X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM), and Transmission Electron Microscopy (TEM). Mechanical characterization was performed using Vickers microhardness and uniaxial tensile testing, while the tribological behavior was assessed using sliding wear tests under dry/lubricated conditions. XRD analysis revealed that increased cryomilling duration led to significant crystallite refinement, which directly correlated with enhanced hardness and strength. This mechanical strengthening was accompanied by an increase in coefficient of friction (COF) and lower wear rates. The results also showed that the Mg-doped Al exhibited superior hardness, tensile strength, and tribological performance compared to pure Al. The study further explores the underlying mechanisms responsible for these enhancements, highlighting the potential of solute-assisted grain boundary stabilization in tailoring high-performance NC Al alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Conversion Kinetics and Ionic Conductivity in Na-β”-Alumina + YSZ (Naβ”AY) Sodium Solid Electrolyte via Vapor Phase Conversion Process

Sodium ion batteries have been receiving increasing attention and may see potential revival in the near future, particularly in large-scale grid energy storage coupling with wind and solar power generation, due to the abundant sodium resources, low cost, and sufficiently high energy density. Among the known sodium ion conductors, the Na-β”-alumina electrolyte remains highly attractive because of its high ionic conductivity. This study focuses on the vapor phase synthesis of a Na-β”-Alumina + YSZ (Naβ”AY) composite sodium electrolyte, which has higher mechanical strength and stability than conventional single phase β”-Alumina. The objectives are the measurement of conversion kinetics through a newly developed weight-gain based model and the determination of sodium ionic conductivity in the composite electrolyte. Starting samples contained ~70 vol% α-Alumina and ~30 vol% YSZ (3 mol% Y 2 O 3 stabilized Zirconia) with and without a thin alumina surface layer made by sintering in air at 1600 °C. The sintered samples were placed in a powder of Na-β”-alumina and heat-treated at 1250 °C for various periods. Sample dimensions and weight were measured as a function of heat treatment time. The conversion of α-Alumina in the α-Alumina + YSZ composite into Naβ”AY occurred by coupled diffusion of sodium ions through Na-β”-alumina and of oxygen ions through YSZ, effectively diffusing Na2O. From the analysis of the time dependence of sample mass and dimensions, the effective diffusion coefficient of Na 2 O through the sample, D eff , was estimated to be 1.74 x 10 -7 cm2 s -1 , and the effective interface transfer parameter, k eff , was estimated as 2.33 x 10 -6 cm s -1 . By depositing a thin alumina coating layer on top of the bulk composite, the chemical diffusion coefficient of oxygen through single phase Na-β”-alumina was estimated as 4.35 x 10 -10 cm 2 s -1 . An AC impedance measurement was performed on a fully converted Naβ”AY composite, and the conductivity of the composite electrolyte was 1.3 x 10 -1 S cm -1 at 300 °C and 1.6 x 10 -3 S cm -1 at 25 °C, indicating promising applications in solid state or molten salt batteries at low to intermediate temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2020

High-Temperature and High-Pressure In Situ Magic Angle Spinning Nuclear Magnetic Resonance Spectroscopy

Nuclear magnetic resonance (NMR) spectroscopy represents an important technique to understand the structure and bonding environment of molecules. There exists a drive to conduct characterization experiment under conditions relevant to the chemical process of interest. To address this, in situ high-temperature, high-pressure MAS NMR methods have been developed to enable the observation of chemical interactions over a range of pressures (vacuum to several hundred bar) and temperatures (well below 0°C to 250°C). Further, the chemical identity of the samples can be comprised of solids, liquids, and gases or mixtures of the three. The method incorporates all-zirconia NMR rotors (sample holder for MAS NMR) which can be sealed using a threaded cap to compress an O-ring. This rotor exhibits great chemical resistance, temperature compatibility, low NMR background, and can withstand high pressures. These factors combined enable its use in a wide range of system combinations which permit its use in diverse fields as carbon sequestration, catalysis, material science, geochemistry, and biology. The flexibility of this technique makes it an attractive option for scientists from numerous disciplines.

Nuclear Magnetic Resonance, NMR, in situ, spectros↗
DOE OSTI2020

Experimental Investigation of Low Cost, Low Thermal Conductivity Thermal Barrier Coating on HCCI Combustion, Efficiency, and Emissions

In-cylinder surface temperature is of heightened importance for Homogeneous Charge Compression Ignition (HCCI) combustion since the combustion mechanism is thermo-kinetically driven. Thermal Barrier Coatings (TBCs) selectively manipulate the in-cylinder surface temperature, providing an avenue for improving thermal and combustion efficiency. A surface temperature swing during combustion/expansion reduces heat transfer losses, leading to more complete combustion and reduced emissions. At the same time, achieving a highly dynamic response sidesteps preheating of charge during intake and eliminates the volumetric efficiency penalty. The magnitude and temporal profile of the dynamic surface temperature swing is affected by the TBC material properties, thickness, morphology, engine speed, and heat flux from the combustion process. This study follows prior work of authors with Yttria Stabilized Zirconia, which systematically engineered coatings for HCCI combustion. Herein, a modeling study was used to assess the impacts of various TBC material properties, e.g. density, thickness, and thermal conductivity on the temperature swing effect. Reducing conductivity emerged as a most promising avenue, rather than reducing both the density and effective conductivity by increasing porosity, the current work emphasizes a material with natively low conductivity. A novel TBC formulation was developed, leverages a class of materials that, to the author’s best knowledge, have not been used as a thermal barrier coating previously. Here, a systematic experimental investigation was carried out using single-cylinder research engine. Experimental engine studies utilizing the novel ‘glassy’ low-K coating exhibit advanced ignition phasing and reduced combustion duration relative to the baseline engine. Heat transfer measurements indicate a net reduction in heat flux over the entire cycle, although main effect is felt during expansion, and the reduced heat transfer losses manifest in higher gross indicated thermal efficiency by approximately 5-6% on a relative basis.

42 ENGINEERING↗