Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “traces”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS2017

Evaluation of a Candidate Trace Contaminant Control Subsystem Architecture: The High Velocity, Low Aspect Ratio (HVLA) Adsorption Process

Traditional gas-phase trace contaminant control adsorption process flow is constrained as required to maintain high contaminant single-pass adsorption efficiency. Specifically, the bed superficial velocity is controlled to limit the adsorption mass-transfer zone length relative to the physical adsorption bed; this is aided by traditional high-aspect ratio bed design. Through operation in this manner, most contaminants, including those with relatively high potential energy are readily adsorbed. A consequence of this operational approach, however, is a limited available operational flow margin. By considering a paradigm shift in adsorption architecture design and operations, in which flows of high superficial velocity are treated by low-aspect ratio sorbent beds, the range of well-adsorbed contaminants becomes limited, but the process flow is increased such that contaminant leaks or emerging contaminants of interest may be effectively controlled. To this end, the high velocity, low aspect ratio (HVLA) adsorption process architecture was demonstrated against a trace contaminant load representative of the International Space Station atmosphere. Two HVLA concept packaging designs (linear flow and radial flow) were tested. The performance of each design was evaluated and compared against computer simulation. Utilizing the HVLA process, long and sustained control of heavy organic contaminants was demonstrated.

Kayatin, Matthew J.↗
NASA NTRS2017

Trace Contaminant Control During the International Space Station's On-Orbit Assembly and Outfitting

During the International Space Station’s (ISS’s) on-orbit assembly and outfitting, a series of engineering analyses was conducted to evaluate how effective the passive trace contaminant control (TCC) methods were relative to providing adequate operational margin for the active TCC equipment’s capabilities aboard the ISS. These analyses were based on habitable module and cargo vehicle offgassing test results. The offgassing test for the fully assembled module or cargo vehicle is an important preflight spacecraft evaluation method that has been used successfully during all crewed spacecraft programs to provide insight into how effectively the passive contamination control methods limit the equipment offgassing component of the overall trace contaminant generation load. The progression of TCC assessments beginning in 1998 with the ISS’s first habitable element launch and continuing through the final pressurized element’s arrival in 2010 are presented. Early cargo vehicle flight assessments between 2008 and 2011 are also presented as well as a discussion on predictive methods for assessing cargo via a purely analytical technique.

Contamination control↗
NASA NTRS2017

Tracing the Cosmological Evolution of Stars and Cold Gas with CMB Spectral Surveys

A full account of galaxy evolution in the context of ΛCDM cosmology requires measurements of the average star-formation rate (SFR) and cold gas abundance across cosmic time. Emission from the CO ladder traces cold gas, and [C II] fine structure emission at 158 μm traces the SFR. Intensity mapping surveys the cumulative surface brightness of emitting lines as a function of redshift, rather than individual galaxies. CMB spectral distortion instruments are sensitive to both the mean and anisotropy of the intensity of redshifted CO and [C II] emission. Large-scale anisotropy is proportional to the product of the mean surface brightness and the line luminosity-weighted bias. The bias provides a connection between galaxy evolution and its cosmological context, and is a unique asset of intensity mapping. Cross-correlation with galaxy redshift surveys allows unambiguous measurements of redshifted line brightness despite residual continuum contamination and interlopers. Measurement of line brightness through cross-correlation also evades cosmic variance and suggests new observation strategies. Galactic foreground emission is ≈10(exp 3) times larger than the expected signals, and this places stringent requirements on instrument calibration and stability. Under a range of assumptions, a linear combination of bands cleans continuum contamination sufficiently that residuals produce a modest penalty over the instrumental noise. For PIXIE, the 2σ sensitivity to CO and [C II] emission scales from »5 ´ 10-2 kJy sr-1 at low redshift to ≈2 kJy sr(exp -1) by reionization.

Switzer, Eric R.↗
NASA NTRS2018

Atmospheric Trace Gas (NO2 and Ozone) Dynamics over Coastal Waters near Polluted Urban Regions

At the interface between the land, oceans, and atmosphere, coastal regions are highly dynamic environments, characterized by strong variability in both water and air quality. Variability in atmospheric composition is associated with highly variable anthropogenic emissions, as well as complex meteorological processes that influence the circulation and accumulation of atmospheric pollutants at the land-ocean interface. Assessing the spatial and temporal dynamics of atmospheric pollutants, aerosols, and absorbing trace gases in coastal areas is critical for improving modeling of coastal tropospheric air quality, developing accurate satellite retrievals of coastal ocean color and biological processes, determining impacts of atmospheric pollution on human health, and assessing the ecological implications of atmospheric pollutant deposition for coastal terrestrial and aquatic ecosystems.Here, we present new measurements of atmospheric trace gas (NO2, and ozone) dynamics across a range of estuarine and coastal waters near urban regions. Measurements were conducted from research vessels using NASA's shipboard Pandora spectrometers, as part of recent multidisciplinary, multiplatform field campaigns, including the 2016 KORUS OC/AQ field campaign in the Yellow Sea and East Sea/Sea of Japan, the 2017/2018 OLWETS field campaign in the Chesapeake Bay estuary, and the 2018 LISTOS field campaign in the Long Island Sound. Shipboard measurements over these coastal waters were integrated with measurements from a ground-based Pandora network to examine differences in air quality over the land and over the ocean. Measurements were combined with air-parcel back-trajectory simulations to determine the origin of air masses over the coastal ocean. Comparisons with satellite retrievals of atmospheric composition reveal the benefits and limitations of polar-orbit satellite observations in capturing variability in atmospheric pollution gradients over land-water boundaries.

Tzortziou, Maria↗
NASA NTRS2014

Airborne In-Situ Trace Gas Measurements of Multiple Wildfires in California (2013-2014)

Biomass burning emissions are an important source of a wide range of trace gases and particles that can impact local, regional and global air quality, climate forcing, biogeochemical cycles and human health. In the western US, wildfires dominate over prescribed fires, contributing to atmospheric trace gas budgets and regional and local air pollution. Limited sampling of emissions from wildfires means western US emission estimates rely largely on data from prescribed fires, which may not be a suitable proxy for wildfire emissions.We report here in-situ measurements of carbon dioxide, methane, ozone and water vapor from the plumes of a variety of wildfires sampled in California in the fire seasons of 2013 and 2014. Included in the analysis are the Rim Fire (August October 2013, near Yosemite National Park), the Morgan Fire (September 2013, near Clayton, CA), and the El Portal Fire (July August 2014, in Yosemite National Park), among others. When possible, fires were sampled on multiple days.Emission ratios and estimated emission factors will be presented and discussed in the context of fuel composition, plume structure, and fire phase. Correlations of plume chemical composition to MODISVIIRS Fire Radiative Power (FRP) and other remote sensing information will be explored. Furthermore, the role of plumes in delivery of enhanced ozone concentrations to downwind municipalities will be discussed.

Gas↗
NASA NTRS2019

A Novel Surface Feature Navigation Algorithm Using Ray Tracing

We demonstrate a novel single-bounce ray tracing approach to landmark identification for surface feature-based relative navigation. A priori knowledge of the camera pose and known topographic maps for each landmark are used to render the potentially visible landmarks via ray tracing into the image frame. These templates are registered with a search region around the predicted location for each landmark in the image, to locate its observed center. This procedure is applied to images from the OSIRIS-REx Orbital A and Orbital B mission phases, and the results are compared with those obtained via previous landmark identification methods.

Gnam, Chris↗
NASA NTRS2019

Dynamic Modeling of Gaseous Multicomponent Trace Contaminant Adsorption

Activated carbon is a porous material in the Trace Contaminant Control (TCC) system that physically adsorbs volatile organic compounds (VOCs) generated within spacecraft and spacesuit environments. Several isotherm models exist to predict adsorption equilibria for processes involving multicomponent systems. This paper investigates the use of Ideal Adsorbed Solution Theory (IAST) for predicting multicomponent trace contaminant adsorption behavior using single-component isotherms based on potential theory. Developing simulations for experimental breakthrough curves will gauge the validity on the sizing and design of TCC architecture. Model results on predicting bed performance and roll-up effects are compared with available multicomponent test data.

Ideal Adsorbed Solution Theory (IAST)↗
NASA NTRS2020

Validation of Carbon Trace Gas Profile Retrievals from the NOAA-Unique Combined Atmospheric Processing System for the Cross-Track Infrared Sounder

This paper provides an overview of the validation of National Oceanic and Atmospheric Administration (NOAA) operational retrievals of atmospheric carbon trace gas profiles, specifically carbon monoxide (CO), methane (CH4) and carbon dioxide (CO2), from the NOAA-Unique Combined Atmospheric Processing System (NUCAPS), a NOAA enterprise algorithm that retrieves atmospheric profile environmental data records (EDRs) under global non-precipitating (clear to partly cloudy) conditions. Vertical information about atmospheric trace gases is obtained from the Cross-track Infrared Sounder (CrIS), an infrared Fourier transform spectrometer that measures high resolution Earth radiance spectra from NOAA operational low earth orbit (LEO) satellites, including the Suomi National Polar-orbiting Partnership (SNPP) and follow-on Joint Polar Satellite System (JPSS) series beginning with NOAA-20. The NUCAPS CO, CH4, and CO2 profile EDRs are rigorously validated in this paper using well-established independent truth datasets, namely total column data from ground-based Total Carbon Column Observing Network (TCCON) sites, and in situ vertical profile data obtained from aircraft and balloon platforms via the NASA Atmospheric Tomography (ATom) mission and NOAA AirCore sampler, respectively. Statistical analyses using these datasets demonstrate that the NUCAPS carbon gas profile EDRs generally meet JPSS Level 1 global performance requirements, with the absolute accuracy and precision of CO 5% and 15%, respectively, in layers where CrIS has vertical sensitivity; CH4 and CO2 product accuracies are both found to be within ±1%, with precisions of ≈1.5% and ⪅0.5%, respectively, throughout the tropospheric column.

satellite cal/val; error analysis; greenhouse gase↗
NASA NTRSDate not supplied

Ray Tracing Techniques for the Characterization of Lunar Communication Architectures

This paper provides an overview of the computational techniques used to characterize the viability of different lunar architectures and their ability to provide communication services to the lunar surface. This analysis was done with modern ray tracing techniques that allow for the computations to be done on Graphics Processing Unit (GPU) clusters for a high level of parallelism and severe reduction in computation time. The ray tracing computations were done with the GPU platform Compute Unified Device Architecture (CUDA) provided by NVIDIA which utilizes general-purpose computing on graphics processing units (GPGPU). This new method provides the advantage of being able to characterize a much larger portion of the lunar surface due to its computational efficiency as well as providing a more accurate representation of elevation angle limits instead of the typical and often inaccurate elevation angle mask. The Lunar surface can now be characterized with metrics such as contact time, outage time, and received data rate. With these metrics, different proposed Lunar architectures can be rapidly evaluated. This reduction in computation time not only leads to more accurate results but allows these results to be obtained in a time frame that allows for the complete characterization of the trade space. It is expected that these different architecture comparisons will lead to a conclusive determination of the optimal Lunar architecture and will allow for future Lunar missions to operate as close to real time as possible. In addition, this computation method can be used to recreate visibility figures generated by previous methods but with an increased level of accuracy.

Thomas Montano↗
NASA NTRSDate not supplied

Streamline-Traced, External-Compression Supersonic Inlets for Mach 2

A computational study was performed to explore the aerodynamic design and performance of streamline-traced, external-compression (STEX) inlets for Mach 2.0. The performance metrics included inlet flow rates, total pressure recovery, and total pressure distortion. The study explored the use of round and flattened capture cross-sections and a bleed slot. The design of the inlet and generation of the inlet geometry was performed using the Supersonic Inlet Design and Analysis(SUPIN) Tool. Computational grids were generated, and methods of computational fluid dynamics (CFD) were applied to solve the three-dimensional, turbulent flow through the inlets using the Wind-US CFD flow solver. It was found that the use of a bleed slot with about 5% bleed resulted in an inlet total pressure recovery of 95% at Mach 2 with acceptable radial and circumferential total pressure distortion. It was also found that there was only a slight decrease in performance between a round and flattened capture cross-section. This suggests that the use of streamline tracing offers flexibility in shaping the inlet capture cross-section for a more favorable integration with an aircraft wing or fuselage. This flexibility and the good performance of the inlet provides a novel inlet design for future commercial supersonic aircraft.

Computational Fluid Dynamics↗
NASA NTRSDate not supplied

Streamline‐Traced, External‐Compression Supersonic Inlets for Mach 2

A computational study was performed to explore the aerodynamic design and performance of streamline-traced, external‐compression (STEX) inlets for Mach 2.0. The performance metrics included inlet flow rates, total pressure recovery, and total pressure distortion. The study explored the use of round and flattened capture cross‐sections and a bleed slot. The design of the inlet and generation of the inlet geometry was performed using the Supersonic Inlet Design and Analysis (SUPIN) Tool. Computational grids were generated, and methods of computational fluid dynamics (CFD) were applied to solve the three dimensional, turbulent flow through the inlets using the Wind‐US CFD flow solver. It was found that the use of a bleed slot with about 5% bleed resulted in an inlet total pressure recovery of 95% at Mach 2 with acceptable radial and circumferential total pressure distortion. It was also found that there was only a slight decrease in performance between a round and flattened capture cross‐section. This suggests that the use of streamline tracing offers flexibility in shaping the inlet capture cross‐section for a more favorable integration with an aircraft wing or fuselage. This flexibility and the good performance of the inlet provides a novel inlet design for future commercial supersonic aircraft.

Computational Fluid Dynamics↗
NASA NTRS2023

Temperature Effect on Silicate Melt-Sulfide-Metal Trace Element Partitioning in the Presence of Sulfur Under Reduced Conditions

The reduced nature of Mercury, enstatite chondrites, and the aubrite parent bodies (APB) have raised many questions regarding the geochemical behavior of typically lithophile, heat-producing, and rare-earth elements (REE) in magmas at low oxygen fugacity (fO2). Due to decreasing O availability at these low fO2, and an abundance of S(sup 2(-)), sulfur (S) acts as an important anion that changes the partitioning behavior of many elements and modifies the physical properties of silicate melts. Preliminary observations suggest that major and minor elements exhibit different geochemical affinities in highly reduced, S-rich systems compared to terrestrial rocks. The speciation and bonding environment of S, dictated by P/T/fO2 conditions, may strongly influence the degree to which S affects partitioning behavior. Here we investigate the partitioning behavior of major, minor, and trace elements between silicate melt, sulfide melt, and metal as well as the coordination chemistry of S in highly reduced silicate melts. Our work is focused on investigating solely the entropy-dependent temperature effect on partitioning of elements for which we currently have MESSENGER data (K, Na, Th, U, Si, Mg, Fe, Ti, Ca, Al, Cr, Mn, S, Cl) as well as a host of geochemically relevant trace elements such as REEs (P, Co, Ni, Mo, Ce, Nd, Sm, Eu, Gd, Dy, Yb). Previous studies in which temperature, pressure, and fO2 were co-varied found that as fO2 decreases, heat-producing elements U and Th become more chalcophile, while K becomes less chalcophile. Concurrently, nominally lithophile elements Mg and Ca become more chalcophile and were observed as minor elements in exsolved sulfides and bonded with S species in silicate melt. These studies, however, could not disentangle entropic effects from changes in the fO2. New temperature-dependent partitioning data from our work will be used to determine which elements are most likely to retain their lithophile character and hence be incorporated into silicates, and which elements are likely contained within the sulfide (chalcophile) and metal core (siderophile), setting the stage for the thermal and magmatic evolution of reduced planetary bodies.

B A Anzures↗
NASA NTRSDate not supplied

Effect of Pressure on Trace Element Activity Coefficients in Metal-Silicate Systems

The partitioning of trace elements between metal and silicate melts serves as the foundation for understanding the differentiation of a planetary body into a metallic core and silicate mantle. Element activity influences metal-silicate partitioning behavior. Activity coefficients are directly dependent on composition and temperature, and can be indirectly dependent on oxygen fugacity and pressure. Distinguishing the effect of pressure from other variables on the activity coefficients and partitioning is important for understanding the chemical evolution of different planetary bodies during differentiation. In this study, we investigated the influence of pressure on the activity coefficients of Cu, Mo, Pd, Pt, As, Sb, and Bi in Fe-Si metallic liquids. All of these elements exhibit moderate to high activity coefficients in Fe-Si liquids at low pressure, which significantly controls their metal-silicate partitioning behavior. Identifying whether this strong dependence persists at higher pressures is critical to modeling and understanding the chemical consequences of core formation. New experiments at 10 GPa were used to derive activity coefficients for these metals which can be compared to activity coefficients determined at 1 GPa. Experiments were conducted at 10 GPa and 2373K using a 10/5 assembly in the 880-ton multi-anvil press at NASA Johnson Space Center. The standard 10/5 COMPRES assembly was slightly modified to accommodate a sample capsule machined from single-crystal MgO that minimizes melt percolation out of the sample volume during the experiment. Experiment starting materials were comprised of 70 wt.% Knippa basalt and 30 wt.% metal. The metal mixture (~85 wt.% Fe) was created by adding the elements of interest (Cu, Mo, Pd, Pt, As, Sb, Bi) to Fe metal powder. Varied amounts of Si metal (0-10 wt.% Si) were added to the metal-silicate mixtures to generate a systematic series of starting materials. For each element, an epsilon interaction parameter in Fe-Si liquid was derived from the results of our 0-10 wt.% Si metal series. To investigate whether pressure influences the trace element activity coefficients in the 1-10 GPa pressure range, we compared our results at 10 GPa to those at 1-4 GPa [1-3]. Our results can also be directly compared to interaction parameters for Au, P, V, Mn, Ga, Zn, Cd, Sn, W, Pb, and Nb previously determined at 10 GPa and 2373K following the same methods [4]. Combined, this suite of interaction parameters will directly inform metal-silicate partitioning between 1 and 10 GPa, and assess whether these values can be extrapolated to modeling differentiation processes at pressures >10 GPa.

Kelsey Prissel↗
NASA NTRSDate not supplied

All-sky Retrieval of Atmospheric Temperature, Water Vapor, Clouds, Trace Gases, and Surface Properties from Operational Hyperspectral IR Sounders

Operational IR sounders such AIRS, CrIS, and IASI provide high quality hyperspectral measurements for weather and climate applications. We will describe a new all-sky Single Field-of-view Sounder Atmospheric Product (SiFSAP). The uniqueness of this product is that it uses all available channels from hyperspectral sounders and the optimal estimation retrieval is done at a single FOV spatial resolution. The SiFSAP includes atmospheric temperature, water vapor, clouds, trace gases, surface skin, and surface emissivity and will be produced operationally at NASA GES DISC. We will describe the core component of the SiFSAP algorithm, which is the Principal Component-based Radiative Transfer Model (PCRTM), and will show example applications of the SiFSAP product for various atmospheric weather and dynamics studies. We also describe a new Climate Fingerprinting Sounder Product (ClimFiSP), which is derived from spatiotemporally averaged level-1 hyperspectral radiances directly. The ClimFiSP algorithm uses consistent radiative kernels and a robust spectral fingerprinting method. It provides fast and accurate data fusion products from multiple satellite sensors. We have applied this method to both AIRS and CrIS (on SNPP and on NOAA 20) data and generated two decades climate data records for atmospheric temperature, water vapor, cloud, trace gases, and surface skin temperature. The ClimFiSP are being transitioned to NASA data centers for routine generations level-3 products.

pcrtm↗
NASA NTRSDate not supplied

Ammonia-Removal Efficiency By Full-Scale Carbon-Based Trace-Contaminant Sorbent Monoliths Integrated With the Rapid-Cycle Amine (RCA) Swing Bed

Results are presented on full-scale performance testing of vacuum-regenerable, carbon based sorbent monoliths for trace-contaminant (TC) removal integrated with the Rapid-Cycle Amine (RCA) swing bed for use in the Portable Life Support System (PLSS) during Extravehicular Activities (EVAs). The current state-of-art in TC-control technology involves the use of a packed bed of acid-impregnated granular charcoal, which is difficult to regenerate. The carbon-based sorbent under development in this project can be regenerated by exposure to vacuum at room temperature. Data on cyclic sorption-desorption of ammonia, which is a major TC of concern, were collected in a simulated PLSS ventilation loop which involved the RCA placed upstream of the Trace Contaminant Control System (TCCS). Results of testing involving pressure-swing operation of the integrated TCCS/RCA system indicate ammonia-removal efficiency exceeding 80% throughout multiple sorption-desorption cycles. This paper presents an overview of the TCCS research, the favorable results obtained, and provides insight into future work needed to further the technology development.

Marek A Wójtowicz↗
NASA NTRSDate not supplied

Tracking the Hunga Tonga-Hunga Ha’apai Eruption Stratospheric Aerosol and Trace Gas Plumes Using Machine Learning

The Hunga Tonga-Hunga Ha’apai (HTHH) submarine volcano had an explosive eruption phase on January 15, 2022, that thrusted ash, gases, and water vapor through the troposphere and into the stratosphere. The stratospheric volcanic plume included aerosol precursor gases such as SO2 and H2S as well as anomalously high water vapor concentrations due to the submarine oceanic origin. With these atmospheric constituents, the sulfuric gases and water vapor formed sulfate (SO4) particles via gas-to-particle reactions and these aerosols likely increased in size due to hygroscopic growth within anomalously humid regions. Strong easterlies and gravity waves propagated the volcanic impacts throughout the stratosphere. Orbital and suborbital passive sensor retrievals detected changes in the aerosol and trace gas characteristics within the atmospheric column for cloud-free regions over the southern hemisphere. While the CALIPSO lidar can detect aerosol layers in the stratosphere, passive sensors such as MODIS retrieved the total column aerosol abundance and characteristics. Previous studies used manual tracking methods to determine volcanic plume positions and compared them to ground observations. In this study, we examine the machine learning (ML) approaches including segmentation, object detection, and object tracking to identify and track aerosol and trace gas plumes using orbital and suborbital sensor data. This ML implementation strives to provide a more systematic approach to separate total column effects from those of the stratosphere. Similar ML tracking may be useful for stratospheric impact events observed historically by CALIPSO and in the future with EarthCare and the Atmosphere Observing System (AOS) lidar-capable missions.

Rhys Leahy↗
DOE OSTI2020

Ambient Mass Spectrometry Rapid Analysis Methods for Trace Inorganics

The ability to rapidly detect and characterize the chemistry of trace quantities of inorganic species has multiple potential applications, including nuclear safeguards, nuclear forensics, and environmental monitoring. Some mass spectrometric methods currently exist, but they are costly and time-intensive, often destroying chemical information in the process of ionization. Ambient mass spectrometry is a relatively new analytical method in which samples are introduced to the mass spectrometer from atmospheric pressure, rather than from high vacuum. Ambient MS can operate with gentler ionization methods such as electrospray ionization (ESI) and paper-spray ionization (PSI), reducing fragmentation and preserving the chemical information of the analyte. This may be useful for determining the intended purpose of material in a sample. Strontium, part of nuclear fallout, is analyzed here to test these new analytical methods for viability. Electrospray ionization mass spectrometry functions by spraying the sample as a solution through a needle charged to a few kV. A nebulizing gas flows out along with the sample to create the spray before droplets enter a drying chamber with heated drying gas to remove the solvent molecules. From there bare analyte ions enter the mass spectrometer. This method has the advantage of relatively fast sample preparation and stable ionization. More stable ionization produces higher-quality data. Paper-spray ionization mass spectrometry operates by applying sample to a paper triangle. The paper triangle is then electrified in a metal clamp to a few kV before spray solvent is applied. The spray solvent transports analyte in the sample to the tip, where it is ionized and enters the mass spectrometer. One advantage of this method is reduced sample preparation - an analyst can even swipe a surface and cut a triangle directly from the swipe. The data analysis serves to rapidly process tens of samples all at once. The mass spectrometer outputs a file containing a few hundred spectra for each sample. The pipeline processes each one to identify peaks of interest. A full palette of data analysis metrics are generated, including plots of the raw data and plots of calculated values such as isotopic ratios. The pipeline filters the raw data to remove noise and background peaks, as well as peaks representing detector saturation. A heat map is generated to show the overall spectrum in mass-time- intensity space. Post-processing, we obtained the desired calibration curves, demonstrating that both ESI-MS and PSI-MS are viable methods for quantifying trace amounts of inorganics while retaining their chemical speciation information. ESI-MS demonstrated a linear response region of 100 ppb to 20 ppm, with a limit-of-detection of around 100 ppb. At top left is an example spectrum with the {sup 88}SrNO{sub 3} peak identified to show the retention of chemical speciation. PSI-MS showed a linear response region of around 1 ppb to 1 ppm, with a limit-of-detection of near 1 ppb. PSI-MS produced more erratic results than ESI-MS, likely due to the variability in ionization resulting from manual positioning of the paper triangle near the MS inlet. Future efforts will focus on improving the repeatability of PSI-MS as well as analyzing other species of interest such as cerium and uranium. Improvements will also be made to create more reliable data extraction and intelligent data filtering.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Poincaré complex diagonals and the Bass trace conjecture

For a finitely dominated Poincaré duality space M, we show how the first author's total obstruction μ M to the existence of a Poincaré embedding of the diagonal map M→M×M relates to the Reidemeister trace of the identity map of M. We then apply this relationship to show that μ M vanishes when suitable conditions on the fundamental group of M are satisfied.

97 MATHEMATICS AND COMPUTING↗