Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “time distribution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Improving protonic ceramic electrochemical cell performance via a dual-phase reaction-sintered bilayer electrolyte

Protonic ceramic electrochemical cells (PCCs) are promising energy conversion devices, but their fabrication remains challenging. In particular, the typical electrolytes for PCCs such as BaCe 0.7 Zr 0.1 Y 0.1 Yb 0.1 O 3−δ (7111) and BaCe 0.4 Zr 0.4 Y 0.1 Yb 0.1 O 3−δ (4411) suffer from intrinsic barium evaporation issues during high-temperature sintering. This tendency towards barium loss, combined with their highly refractory nature, leads to a tradeoff between sinterability and chemical stability. To address this tradeoff, we propose a bilayer electrolyte combining layers of 4411 and 7111 materials that is designed to enhance sinterability and conductivity through dual-phase reactive sintering. Our findings demonstrate that the bilayer structure exhibits shrinkage behavior closely matched to that of the fuel electrode substrate, with a higher shrinkage compared to a single-layer 4411 electrolyte. Utilizing this bilayer electrolyte structure, our PCCs achieve a peak power density of 637 mW∙cm −2 in fuel-cell mode and a current density of 1060 mA∙cm −2 at 1.3 V in electrolysis mode at 600 °C. Our PCCs demonstrate high Faradaic efficiency of 83% at 1.3 V and 500 °C. Hybrid distribution of relaxation times (DRT) polarization mapping further reveals that the bilayer structure reduces Ohmic and polarization resistance in both fuel-cell and electrolysis modes.

ceramic processing↗
DOE OSTI2022

Characterization of the Emissions and Crystalline Silica Content of Airborne Dust Generated from Grinding Natural and Engineered Stones

Abstract In this study, we systematically characterized the airborne dust generated from grinding engineered and natural stone products using a laboratory testing system designed and operated to collect representative respirable dust samples. Four stone samples tested included two engineered stones consisting of crystalline silica in a polyester resin matrix (formulations differed with Stones A having up to 90wt% crystalline silica and Stone B up to 50wt% crystalline silica), an engineered stone consisting of recycled glass in a cement matrix (Stone C), and a granite. Aerosol samples were collected by respirable dust samplers, total dust samplers, and a Micro-Orifice Uniform Deposit Impactor. Aerosol samples were analyzed by gravimetric analysis and x-ray diffraction to determine dust generation rates, crystalline silica generation rates, and crystalline silica content. Additionally, bulk dust settled on the floor of the testing system was analyzed for crystalline silica content. Real-time particle size distributions were measured using an Aerodynamic Particle Sizer. All stone types generated similar trimodal lognormal number-weighted particle size distributions during grinding with the most prominent mode at an aerodynamic diameter of about 2.0-2.3 μm, suggesting dust formation from grinding different stones is similar. Bulk dust from Stone C contained no crystalline silica. Bulk dust from Stone A, Stone B, and granite contained 60, 23, and 30wt% crystalline silica, respectively. In Stones A and B, the cristobalite form of crystalline silica was more plentiful than the quartz form. Only the quartz form was detected in granite. The bulk dust, respirable dust, and total dust for each stone had comparable amounts of crystalline silica, suggesting that crystalline silica content in the bulk dust could be representative of that in respirable dust generated during grinding. Granite generated more dust per unit volume of material removed than the engineered stones, which all had similar normalized dust generation rates. Stone A had the highest normalized generation rates of crystalline silica, followed by granite, Stone B, and Stone C (no crystalline silica), which likely leads to the same trend of respirable crystalline silica (RCS) exposure when working with these different stones. Manufacturing and adoption of engineered stone products with formulations such as Stone B or Stone C could potentially lower or eliminate RCS exposure risks. Combining all the effects of dust generation rate, size-dependent silica content, and respirable fraction, the highest normalized generation rate of RCS consistently occurs at 3.2-5.6 µm for all the stones containing crystalline silica. Therefore, removing particles in this size range near the generation sources should be prioritized when developing engineering control measures.

Public, Environmental & Occupational Health↗
DOE OSTI2025

Habitat-specific seasonal densities of sympatric raccoons and opossums in the southeastern United States

Raccoon and opossum densities have implications for rabies management, but estimates of seasonal densities of both species are lacking for rural nonagricultural habitats of the southeastern United States, a core portion of their geographic range. Consequently, it remains unclear whether the densities of 1 species limit the other, which is possible considering their substantial niche overlap. We carried out a mark–recapture study of raccoons and opossums in 4 rural nonagricultural habitats (bottomland hardwood forest, riparian forest, upland pine forest, and isolated wetlands) in South Carolina, United States (2020 to 2022), and combined this with previous data from the same habitats (2017 to 2019) to estimate habitat-specific spring and fall densities. Raccoon densities ranged from 5.17 ± 0.96 animals/km 2 (bottomland hardwood fall) to 1.63 ± 0.83 animals/km 2 (upland pine spring) and were on average 19% higher in fall compared to spring. Opossum densities ranged from 10.35 ± 1.98 animals/km 2 (bottomland hardwood fall) to 1.11 ± 1.55 animals/km 2 (upland pine spring) with divergent seasonal patterns among habitats. These low densities across all habitats compared to other studies are likely the result of low resource availability, consistent with other habitats that have minimal anthropogenic influence. We observed a positive association between raccoon and opossum densities across trapping grids, suggesting that raccoons do not suppress opossum densities, but that densities of both species increase with increasing resource availability. Furthermore, our results can be used to inform oral rabies vaccination efforts such as refining bait densities and timing of bait distribution in these habitats.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2022

Long-term 3D MHD simulations of black hole accretion discs formed in neutron star mergers

ABSTRACT We examine the long-term evolution of accretion tori around black hole (BH) remnants of compact object mergers involving at least one neutron star, to better understand their contribution to kilonovae and the synthesis of r-process elements. To this end, we modify the unsplit magnetohydrodynamic (MHD) solver in flash 4.5 to work in non-uniform three-dimensional spherical coordinates, enabling more efficient coverage of a large dynamic range in length scales while exploiting symmetries in the system. This modified code is used to perform BH accretion disc simulations that vary the initial magnetic field geometry and disc compactness, utilizing a physical equation of state, a neutrino leakage scheme for emission and absorption, and modelling the BH’s gravity with a pseudo-Newtonian potential. Simulations run for long enough to achieve a radiatively inefficient state in the disc. We find robust mass ejection with both poloidal and toroidal initial field geometries, and suppressed outflow at high disc compactness. With the included physics, we obtain bimodal velocity distributions that trace back to mass ejection by magnetic stresses at early times, and to thermal processes in the radiatively inefficient state at late times. The electron fraction distribution of the disc outflow is broad in all models, and the ejecta geometry follows a characteristic hourglass shape. We test the effect of removing neutrino absorption or nuclear recombination with axisymmetric models, finding ${\sim} 50{{\ \rm per\ cent}}$ less mass ejection and more neutron-rich composition without neutrino absorption, and a subdominant contribution from nuclear recombination. Tests of the MHD and neutrino leakage implementations are included.

Fahlman, Steven (ORCID:0000000348759940)↗
DOE OSTI2025

Measurement of the liquid argon scintillation pulse shape using differentiable simulation in the coherent CAPTAIN-Mills experiment

The coherent CAPTAIN-Mills (CCM) experiment is a liquid argon (LAr) light collection detector searching for MeV-scale neutrino and beyond Standard Model physics signatures. Two hundred eight-inch photomultiplier tubes instrument the seven-ton fiducial volume with 50% photocathode coverage to detect light produced by charged particles. CCM’s light-based approach reduces requirements of LAr purity, compared to other detection technologies, such that sub-MeV particles can be reliably detected without additional LAr filtration and with 𝒪⁡(1) parts per million of common contaminants. We present a measurement of LAr light production and propagation parameters, with uncertainties, obtained from a sample of MeV-scale electromagnetic events. The optimization of this high-dimensional parameter space was facilitated by a differentiable optical photon Monte Carlo simulation and detailed photomultiplier tube response characterization. This result accurately predicts the timing and spatial distribution of light due to scintillation and Cherenkov emission in the detector. This is the first description of photon propagation in LAr to include several effects, including anomalous dispersion of the index of refraction near the ultraviolet resonance, Mie scattering from impurities, and Cherenkov light production.

Cherenkov detectors↗
DOE OSTI2021

Level structure of the T z = –1 nucleus 34 Ar and its relevance for nucleosynthesis in ONe novae

The 24 Mg+ 12 C fusion reaction was used to perform a detailed γ-ray spectroscopy study of the astrophysically important nucleus 34 Ar. In particular, an experimental setup, coupling the advanced γ-ray tracking array GRETINA with the well-established Argonne fragment mass analyzer (FMA), was employed to obtain excitation energies and spin-parity assignments for excited states in 34 Ar, both above and below the proton separation energy. For the first time, an angular distribution analysis of in-beam γ rays from fusion-evaporation reactions, using a tracking array, has been performed and Coulomb energy differences of analog states in the T = 1, A = 34 mirror system, explored from 0 to 6 MeV. Lastly, we present a comprehensive discussion of the astrophysical 33 Cl(p,γ) stellar reaction rate, together with implications for the identification of nova presolar grains from sulfur isotopic abundances.

20 ≤ A ≤ 38↗
DOE OSTI2023

Adaptive autoencoder latent space tuning for more robust machine learning beyond the training set for six-dimensional phase space diagnostics of a time-varying ultrafast electron-diffraction compact accelerator

In this work, we present a general adaptive latent space tuning approach for improving the robustness of machine learning tools with respect to time variation and distribution shift. We demonstrate our approach by developing an encoder-decoder convolutional neural network-based virtual 6D phase space diagnostic of charged particle beams in the HiRES ultrafast electron diffraction (UED) compact particle accelerator with uncertainty quantification. Our method utilizes model-independent adaptive feedback to tune a low dimensional 2D latent space representation of ~1 million dimensional objects which are the 15 unique 2D projections (x, y),...,(z, p z ) of the 6D phase space (x, y, z, p x , p y , p z ) of the charged particle beams. We demonstrate our method with numerical studies of short electron bunches utilizing experimentally measured UED input beam distributions.

43 PARTICLE ACCELERATORS↗
DOE OSTI2022

Role of Local Structure in the Enhanced Dynamics of Deformed Glasses

External stress can accelerate molecular mobility of amorphous solids by several orders of magnitude. The changes in mobility are commonly interpreted through the Eyring model, which invokes an empirical activation volume. Here, we analyze constant-stress molecular dynamics simulations and propose a structure-dependent Eyring model, connecting activation volume to a machine-learned field, softness. We show that stress has a heterogeneous effect on the mobility that depends on local structure through softness. The barrier impeding relaxation reduces more for well-packed particles, which explains the narrower distribution of relaxation time observed under stress.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2021

Quantitative Characterization of the Microstructure-Property Relationships in Ni and MIEC Nanocatalyst-Infiltrated Ni/YSZ Anodes

The performance of solid oxide fuel cell (SOFC) anodes can be improved by infiltration of nanoscale electrocatalysts, which increases triple phase boundary (TPB) density, but only when the added TPBs are active. Quantitative characterization of the microstructure of infiltrated nanocatalysts remains a critical challenge in understanding their role in improved performance. This paper explores the relationship between electrochemical performance and microstructure for Ni/YSZ anodes infiltrated with Ni, gadolinium-doped-ceria (GDC), and Ni/GDC nanocatalysts using a combination of electrochemical impedance spectroscopy (EIS), distribution of relaxation times (DRT) analysis, scanning electron microscopy (SEM) microstructural characterization, and three-dimensional (3-D) anode reconstruction. Estimated polarization resistance improvements as a result of nickel nanoparticle infiltration are discussed.

Rix, Jillian↗
DOE OSTI2020

Improving SOFC Anode Electrocatalytic Activity Using Nanoparticle Infiltration into MIEC Compositions

Mitigating activation polarization in the anode is one of the major challenges in intermediate-temperature operation of solid oxide fuel cells (SOFCs). Liquid phase infiltration of nanoscale electrocatalysts has been shown to result in significant reductions in activation polarization in SOFC anodes. In this study, we explore liquid-phase infiltration of nickel, gadolinium doped ceria (GDC), and Ni/GDC electrocatalysts into two different types of cermet anodes: one with a conventional Ni-YSZ composition, and the other with a Ni-MIEC cermet anode where the YSZ has been doped with 3 mol% TiO 2 to impart electronic conductivity. The principal goal of this study is to explore the role of electronic transport in the MIEC phase in effective utilization of the infiltrated nanoscale electrocatalysts. The role of temperature, infiltration cycles and the type of electrocatalysts have been experimentally studied in symmetric cells using electrochemical impedance spectroscopy (EIS). Distribution of relaxation times (DRT) modeling has been used to elucidate the contributions of various charge transfer processes.

25 ENERGY STORAGE↗
DOE OSTI2021

Quantifying Percolated Triple Phase Boundary Density and Its Effects on Anodic Polarization in Ni-Infiltrated Ni/YSZ SOFC Anodes

Increasing the density of percolated triple phase boundaries (TPBs) by infiltrating nanoscale electrocatalysts can improve the performance of solid oxide fuel cell (SOFC) anodes. However, the complex microstructure of these infiltrated nanocatalysts creates challenges in quantifying their role in anode performance improvements. In this research, scanning electron microscopy of fractured cross-sections of a Ni-nanocatalyst infiltrated anodic symmetric cell along with three-dimensional (3-D) reconstruction of the same anode have been used to quantify the changes in percolated TPB densities due to infiltration. This change in percolated TPB density has been compared to the improvement in anode activation polarization resistance measured by electrochemical impedance spectroscopy (EIS). It was found that increased TPB densities only partially accounted for the measured performance improvement. Distribution of relaxation times (DRT) analyses showed that a reduction in the time constants of the catalytic processes in the anode also play a role, suggesting that the added nanoscale percolated TPB boundaries are more electrochemically active as compared to the cermet TPB boundaries.

25 ENERGY STORAGE↗
DOE OSTI2022

Investigating the Influence of Ni, ZrO 2 , and Y 2 O 3 from SOFC Anodes on Siloxane Deposition

Siloxanes, as a type of impurity in biogas, can poison the Ni-YSZ anode of SOFCs. However, the influence of individual components of the anode, such as Ni, ZrO 2 , and Y 2 O 3 , on the siloxane deposition process has not been investigated extensively. In this study, Ni, ZrO 2 , and Y 2 O 3 pellets were exposed to H 2 + N 2 + H 2 O + D4 (octamethylcyclotetrasiloxane, 2.5 ppmv) and H 2 + N 2 + D4 (2.5 ppmv siloxane) gas mixtures at 750 °C to investigate their affinity and tolerance for siloxane degradation. Surface morphology analysis and electrochemical analysis including electrochemical impedance spectroscopy (EIS), related distribution of relaxation times (DRT) analysis and equivalent circuit modeling with complex nonlinear least square (CNLS) fitting were conducted. Here, a microstructure parameter—tortuosity factor to porosity ratio $\tau /\varepsilon $ calculated by diffusion polarization resistance was utilized for siloxane deposition evaluation. After comparing pellets surface morphology changes before and after experiments and $\tau /\varepsilon $ change following the contamination, Ni is considered as a major factor in siloxane deposition reactions in Ni-YSZ anode.

25 ENERGY STORAGE↗
DOE OSTI2021

Laser-induced fluorescence thermometry of supercritical CO 2 flows inside a micro-channel

This work demonstrates a thermometric technique using laser-induced fluorescence (LIF) in supercritical carbon dioxide flows in a micro-channel. Rhodamine 6G was used as a temperature-sensitive fluorescent dye. The flow conditions were at a pressure of 7.9 MPa and temperature in the range of 23°–90°C. 2D spatial distributions and time-resolved temperature profiles were obtained at this high pressure. Measured LIF signals showed close relations to the temperatures obtained from resistance temperature detectors.

Park, Suhyeon↗
DOE OSTI2020

Multiscale-Informed Modeling of High Temperature Component Response with Uncertainty Quantification

This report summarizes a joint effort between Argonne National Laboratory, Idaho National Laboratory, and Los Alamos National Laboratory to develop and deploy constitutive models targeted at predicting the life of Grade 91 alloy components subjected to high temperature environments typical of those that structural components in advanced nuclear reactors would experience. Two distinct, but complementary constitutive modeling approaches have been taken here. The first employs a phenomenological viscoplastic model for which parameters have been calibrated based on experimental data for a wide range of Grade 91 alloy that has undergone a variety of processing. A Bayesian approach was used to derive distributions of uncertain parameters for this model based on this data set. The second approach is a reduced order model suitable for engineering-scale analysis that is based on the results of a large set of mesoscale simulations. Mesoscale models allow for the microstructure and composition of a particular alloy to be directly taken into account in the computation of the viscoplastic response, but are computationally expensive, which makes it impractical to directly call those models for the material constitutive response in an engineering-scale simulation. The reduced-order representation of the response of the underlying model used here allows for an engineering-scale model to take into account the characteristics of the underlying microstructure, while only incurring a reasonable computational expense. Both of these approaches have different strengths, and are applicable for different parts of the design/analysis process. The phenomenological models can be readily parameterized based on a set of experimental data for a given class of materials and used for scoping calculations. Once a specific material is chosen and adequately characterized, the reduced order models can accurately predict the response of that specific alloy, and because the models are based on predictive models of the underlying microstructure, they can be used to more confidently predict the response under conditions in regions where there is limited experimental data. Both of these models have been integrated in the Grizzly code, which is used here to perform proof-of-concept uncertainty quantification analyses of a simple component under prototypical conditions. The built- in stochastic analysis capabilities in the MOOSE framework that Grizzly is built on are used here to run large sets of simulations for this uncertainty quantification analysis. As would be expected, because the reduced order models are developed for a much more tightly defined alloy, they predict tighter distributions of the time to failure than the phenomenological models, which are calibrated to a broader set of data. Also important is that these simulations demonstrate that a reduced order modeling approach can be successfully deployed to propagate uncertainties from the material scale to practical engineering-scale component simulations.

42 ENGINEERING↗
DOE OSTI2021

Minimizing Cr-Evaporation from Balance Of Plant Components By Utilizing Cost-Effective Alumina-Forming Austenitic Steels

A solid oxide fuel cell (SOFC) is a clean and efficient energy conversion device. The development of intermediate-temperature SOFCs has made it preferable to use metallic interconnects (MICs) to greatly reduce the cost and significantly increase the efficiency compared to ceramic interconnect materials. However, gaseous chromium species will evaporate from the chromium-containing layer formed on the surface of commonly used MICs and balance of plant (BoP) components. Volatile chromium species have been shown to form solid deposits which poison the cathodes of SOFCs, causing drastic cell performance degradation and thereby limiting commercialization. In order to alleviate the Cr poisoning and achieve long-term high performance of SOFC stacks, various Al 2 O 3 -forming austenitic (AFA) stainless steels applied at different temperatures are evaluated in this project. Based on our Phase I results (500 h operation), it is shown that on the AFAs, an alumina-based protective layer forms under high temperature that is invulnerable to water vapor effects and suppresses the diffusion of chromium and manganese which can prevent the generation of spinels on the alloy surface. Therefore, 310S, OC4 and OC5 at 800 °C and 625, OC11 and OC11LZ at 900 °C are selected to be tested in the Phase II long-term operation. From the results, we find that besides the lower Cr evaporation rates and better oxidation resistance of AFAs than benchmark alloys after short-term (500 h) operation, AFAs also possess the sturdy and compact alumina layer after a long-term operation (5000 h). A protective oxide layer is of great importance for the long-term high-temperature operation of structural materials. The high-temperature oxidation behavior of AFAs and commercial 310S and 625 alloys in Air + 10% H 2 O at 800 °C and 900 °C is systematically investigated. Severe breakaway oxidation and minor spallation are observed for the 310S and 625 after the long-term operation, while the AFAs show high oxidation resistance. It is found that the formation of a continuous alumina layer could greatly prevent the volatilization of chromium vapors. In addition, the corresponding evolving models are discussed. Chromium evaporation from BoP components in high-temperature environment could severely deteriorate the electrochemical performance of SOFC. Several methods were applied to evaluate the Cr evaporation rates of BoP after 500 h exposure at 800 °C to 900 °C in air with 10% H 2 O. An optimal method was designed to exclude the effect of silicon (Si) deposits from quartz tube and sodium (Na) deposits from the sodium carbonate on the oxidation process and the chemical interaction between Cr gaseous species and alumina tube which could provide further quantitative correlation of the evaporated Cr species quantities and degradation rates of SOFC. Based on the great performance of AFAs after long-term operation, AFAs are assembled with Anode-supported cells (ASC) to investigate the the Cr deposition of anode-supported cell under a constant current density of 0.5 A cm -2 at 800 °C with AFA alloys compared with commercial alloys. In addition, the anodic and cathodic processes are deconvoluted by distribution of relaxation times (DRT) method which are comprehensively discussed. It is found out that the voltage exhibited a slight decrease of 5.09 % and 1.54 % in the presence of OC11 and OC11LZA alloy, respectively. However, a considerable decrease of 22.14 % and 12.06 % was determined in the presence of 310S and 625 alloy, respectively. AFAs possessing the low-cost, low Cr evaporation rates and the high oxidation resistance will make it of great potential to replace the existing BoP components.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2022

Olympus System Backplane Definition

The purpose of this document is to define the backplane of the Olympus firing system, a modular system based on SpaceWire communication between modules. The backplane provides the connection between the modules, controller (embedded in the front module), the SpaceWire router, and an alternative switch. Those connections include SpaceWire links, interlocks, a key, a dead-man switch (DMS)/charge, timing lines, power distribution, geographical addresses, and communication to the human-machine interface (HMI). This backplane is based on the VMEBus International Trade Association (VITA) 46 Specification (VPX) and OpenVPX standards for a 3U backplane. Unless otherwise specified, those standards apply for signal definitions and mechanical specifications.

42 ENGINEERING↗
DOE OSTI2022

High Performance SOFCs with a Superior Stability for Reliable and Durable Power Systems

Next generation of fuel cells, electrolyzers, and batteries requires higher power, faster kinetics, and larger energy density, which necessitate the use of compositionally complex oxides to achieve multifunctionalities and activity. These compositionally complex oxides may change their phases and structures during an electrochemical process – a so-called “electrochemically driven phase transformation”. The origin for such a phase change has remained obscure. More importantly, there is a need to develop high performance solid oxide fuel cells with an enhanced stability. In this work, the La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3 (LSCF) cathode surface is modified by infiltration of Pr 6 O 11 and the power density at 0.8V and 750 °C is improved by 21%. In addition, by replacing the traditional barrier layer Gd 0.2 Ce 0.8 O 1.9 with mixed conducting Pr 0.1 Gd 0.1 Ce 0.8 O 1.9 , the power density increases by 38%. The different mechanism of promotions was investigated by electrochemical impedance spectroscopy. The ohmic resistance is dramatically reduced by applying the PGCO interlayer, and the distribution of relaxation time was used to analyze the mechanism for which the polarization resistance was decreased attributing to the mixed conduction nature in PrO x . An increase of power density at 0.8 V of 0.358 W/cm 2 (71%) is achieved with the implementation of both surface modification and buffer layer engineering. An experimental study and a theoretical analysis were then carried out on phase evolution in praseodymium nickelates. Nickelate-based electrodes show up to 60× greater phase transformation during operation when compared to thermally annealed ones. Theoretical analysis suggests that the presence of a reduced oxygen partial pressure at the interface between the oxygen electrode and the electrolyte is the origin for the phase change in an oxygen electrode. Guided by the theory, an addition of the electronic conduction in the interface layer leads to the significant suppression of phase change, while improving cell performance and performance stability. When an oxygen electrode is under polarization, the oxygen partial pressure at the interface between the oxygen electrode and the electrolyte is lower than that of incoming oxidant. Under a high polarization, the environment at the aforementioned interface may lead to phase transformation of the oxygen electrode. The local oxygen partial pressure is determined by the transport properties at the interfaces. An addition of the electronic conduction in the interface layer, for instance using (Pr,Gd)-doped ceria to replace Gd-doped ceria, results in improved cell performance and performance stability, while the phase transformation is significantly suppressed. This work provides a fundamental understanding of the origin for phase transformation in oxygen electrodes during operation and use this knowledge to develop a high-performance electrode that exhibits improved performance stability.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2022

Large-scale Hydrogen Storage – Risk Assessment Seattle City Light and Port of Seattle [Abstract]

This CRADA presents the strategy that Pacific Northwest National Laboratory (PNNL) and Sandia National Laboratories (SNL) will take to support Seattle City Light (SCL), and the Port of Seattle (Port) in performing a risk assessment of large-scale hydrogen storage. Risk assessment is often used to ensure that adequate measures are taken to protect workers and the public, the environment, infrastructure, and assets. A detailed risk assessment can also be used to direct funding and upgrades, to specific components and sub-systems in order to mitigate risks to the larger system. In this way risk assessments are often employed as a part of a larger risk management strategy, with the goal of minimizing the occurrence of hazards and to identify means to limit their consequences. Risk assessment is often used to engage and inform regulators, and to communicate how specific regulations are being met. However, it is important to note that the proposed work is not intended for SCL and the Port to use in order to gain regulatory acceptance for their proposed activities. The work performed as a part of this effort will be a preliminary risk assessment for early-stage component and system designs and should be considered research and development (R&D). As such, the proposed work will be performed to a quality level and design maturity consistent with R&D and is not considered appropriate for final safety analysis and regulatory compliance purposes. Previous and on-going work at SCL and the Port demonstrated the utility of deploying hydrogen systems at the Port. The deployment of hydrogen at the Port is a part of a larger vision of using hydrogen to address a range of issues for SCL and the Port. These include large-scale fueling of MD/HD vehicles, cargo-handling equipment (CHE), and harbor vessels to reduce emissions; support of adjacent LD vehicles; support of critical port operations during extreme events (i.e., resiliency); deferral of more capital- and time-intensive electrical distribution system upgrades while still supporting evolving port operations and decarbonization efforts; facilitating electrification by establishing energy storage as a grid resource, starting at strategic port locations; creation of a flexible market resource that can be used by SCL to generate revenue via arbitrage; support of planned future maritime operations that involve heavy use of hydrogen for ocean-going vessels; and future end-use applications involving natural gas pipeline hydrogen injection. Ultimately, the success of these activities is underpinned by the deployed storage capacity. Large-scale deployment of hydrogen systems will require hydrogen storage at a scale that has not been demonstrated. In addition, the ideal location for such multi-use systems is near the end user which will often necessitate deploying into urban and/or industrial areas. A detailed risk assessment using the Port as a test case is necessary to ensure the deployment of large-scale hydrogen is successful. Many technologies have been proposed for hydrogen storage; however, these technologies need to be analyzed as they apply to an actual site. The physical infrastructure and hydrogen use cases for the Port will be analyzed, and a risk assessment for compressed hydrogen, liquified hydrogen, and Liquid Organic Hydrogen Carrier (LOHC) storage will be performed. These risk assessments will be useful for understanding how each of these technologies would perform in terms of facility and public safety. The operating states of the proposed hydrogen systems at the Port will be analyzed and incorporated into the storage risk assessment. Scalability will also be analyzed to understand how future port uses would affect the overall risk assessment. Finally, using the risk assessment as a tool to inform engagement and to gain stakeholder acceptance will be explored.

08 HYDROGEN↗