Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “temperature dependence”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Temperature-dependent tensile and shear response of P100/6061 graphite-aluminum

This paper summarizes the results of an investigation conducted to characterize tensile and shear response of P100/6061 graphite-aluminum composite in the temperature range -101 to 260 C. The off-axis tension test and Iosipescu shear test methods were employed to meet this objective. The experimental results indicate that both the fiber-dominated and matrix-dominated elastic properties exhibit relatively small changes in the considered temperature range. The effect of temperature on yielding and strength, however, is significant under longitudinal and shear loading. Residual stresses play a significant role in controlling the variation of the yield stress with temperature. The observed low transverse strength of the composite is explained by interfacial defects between adjacent precursor wires induced during fabrication.

Fujita, Takahiro↗
NASA NTRS1978

A temperature dependent fatigue failure criterion for graphite/epoxy laminates

A fatigue failure criterion applicable to composite materials is developed and applied to predict the fatigue behavior of graphite/epoxy laminates with particular emphasis on the influence of temperature. Tensile stress-strain curves and tension-tension fatigue curves for various unidirectional, angle-ply and symmetrically balanced laminates were developed at test temperatures of 25 C, 74 C, and 114 C. For most laminates a reduction in both static strength and fatigue strength is observed with increasing temperature. This reduction appeared more severe in fatigue loading than in static tensile loading and most severe where the shear stress in the lamina is the dominate failure mode. Through an analytical formulation of shifting functions for the influences of temperature, all fatigue data are shown to be capable of being reduced to a single reference curve at some temperature. Examples are given which demonstrate the capability of the fatigue failure criterion to predict failure of complex symmetrically balanced laminates from relevant parameters obtained from the observed behavior of unidirectional and angle-ply laminates.

Rotem, A.↗
NASA NTRS1979

A temperature dependent fatigue failure criterion for graphite/epoxy laminates

A fatigue failure criterion applicable to composite materials is developed and applied to predict the fatigue behavior of graphite/epoxy laminates with particular emphasis on the influence of temperature. Tensile stress-strain curves and tension-tension fatigue curves for various unidirectional, angle-ply and symmetrically balanced laminates were developed at test temperatures of 25 C, 74 C and 114 C. In general for most laminates a reduction in both static strength and fatigue strength is observed with increasing temperature. This reduction appeared more severe in fatigue loading than in static tensile loading and most severe where the shear stress in the lamina is the dominant failure mode. Through an analytical formulation of shifting functions for the influences of temperature, all fatigue data are shown to be capable of being reduced to a single reference curve at some temperature. Additionally, examples are given which demonstrate the capability of the fatigue failure criterion to predict failure of complex symmetrically balanced laminates from relevant parameters obtained from the observed behavior of unidirectional and angle-ply laminates.

Rotem, A.↗
NASA NTRS1988

The excitation of the O(1S) state by the dissociative recombination of O2(+) ions - Electron temperature dependence

The rate coefficient for the excitation of the O(1S) state due to the dissociative recombination of O2(+) (v of not greater than 3) ions has been determined as a function of the electron temperature from 300-3500 K. In agreement with the work of Guberman (1987), the results suggest that the absolute magnitude of alpha(1S) is nearly the same for a wide variety of O2(+) vibrational distributions over the electron temperature range normally encountered in the nocturnal F-region. It is noted that previous studies which modeled 5577-A airglow data using a fixed value for f(1S) may be misleading.

Zipf, Edward C.↗
NASA NTRS1975

Temperature dependence of the water-ice spectrum between 1 and 4 microns - Application to Europa, Ganymede and Saturn's rings

Reflection spectra of water ice from 1 to 4 microns are presented as a function of temperature. It is found that a feature at 6056 reciprocal cm changes its intensity sufficiently so that it can be used as a spectroscopic measurement of the ice temperature. A temperature calibration curve of this feature down to 55 K is developed and used to determine ice temperatures for the Galilean satellites Europa (95 + or -10 K), Ganymede (103 + or -10 K), and the rings of Saturn (80 + or -5 K). The ice temperatures for the Galilean satellites are lower than their measured brightness temperatures, which can be explained by a higher albedo of the ice-covered regions relative to the rest of the satellite and possibly a concentration of the ice near the polar caps.

Fink, U.↗
DOE OSTI2026

Temperature dependent interfacial microstructure in HIP-bonded Al6061/Zr joints

Pressing (HIP) at 450 °C and 560 °C under 103 MPa for 90 minutes to evaluate interfacial diffusion and microstructural evolution. Sound metallurgical bonding was achieved at both temperatures, with Zr serving as an effective diffusion barrier. Microstructural analysis revealed the the formation of a (Al,Si)3Zr intermetallic layer at the Al/Zr interface, whose thickness increased from ~100 nm at 450 °C to ~2100 nm at 560 °C, consistent with temperature-driven diffusion kinetics. The thin and continuous reaction layer observed at 450 °C indicates controlled interdiffusion and minimal reaction zone growth, favorable for maintaining interface stability and ductility. At 560 °C, enhanced atomic mobility led to pronounced intermetallic development, confirming diffusion-controlled growth behavior. These results provide valuable insights for optimizing Al/Zr interface design and diffusion barrier performance in advanced structural and energy systems.

Al/Zr interface↗
NASA NTRS1972

Temperature-dependent Mg, Fe distribution in a lunar olivine.

The nuclear hyperfine doublets of Fe-57 at the two nonequivalent octahedrally coordinated positions M1 and M2 in an olivine from lunar basalt 12018 have been analyzed in the temperature range between 250 and 450 C. The Mg(2+), Fe(2+) is somewhat ordered, the Fe(2+) occupancy being greater at one of the two M positions by approximately 20%. After heating at 1155 C for seven days, the distribution was almost completely disordered. Studies of natural and heated olivines from terrestrial rocks show that the Mg(2+), Fe(2+) exchange reaction in olivines is considerably more sluggish than in chain silicates. Generally no change in site occupancy can be observed after heating at temperatures of approximately 900 C over several days. The observed degree of ordering in the lunar olivine is indicative of slow cooling during crystallization.

Virgo, D.↗
NASA NTRS1991

Temperature dependence of the anisotropy in magnetic relaxation in YBa2Cu3O(7-x) thin films

The relaxation of diamagnetic magnetization in the c-axis-aligned YBa2Cu3O(7-x) thin film is studied as a function of orientation and temperature in the range of 5-50 K at H = 0.2 T. The magnetization M(T,H) in the orientations H parallel to c and H perpendicular to c and at all the temperatures is found to decrease logarithmically with time t. The activation energy for the movement of flux lines U is found to be 30-110 meV in the range 5-50 K. For H parallel c, U increases continuously with T, whereas for H perpendicular c, U has two apparent maxima: at T = 10 K and T greater than 50 K. These results are discussed in terms of the thermally activated flux motion model.

Vitta, Satish↗
DOE OSTI2023

Growth and passivation of individual carbon nanoparticles by C2H2 addition at high temperatures: Dependence of growth rate and evolution on material and size

Absolute kinetics for reactions of C2H2 with a series of ∼60 individual carbon nanoparticles (NPs) from graphite, graphene, graphene oxide, carbon black, diamond, and nano-onion feedstocks were measured for temperatures (TNP) ranging from 1200 to 1700 K. All the NPs were observed to gain mass by carbon addition under conditions that varied with feedstock but with large variations in initial growth rate. Long reaction periods were studied to allow the evolution of growth rates over time to be observed. Diamond NPs were found to passivate against C2H2 addition if heated above ∼1400 K, and the highly variable initial reactivity for carbon nano-onions was found to depend on the presence of non-onion-structure surface carbon. For graphitic and carbon black NPs, three distinct growth modes were observed, correlated with the initial NP mass (Minitial). Smallest graphitic and carbon black NPs, with masses <∼25 MDa, initially grew rapidly but also passivated quickly after adding <4% of Minitial. NPs in the 20–50 MDa range also passivated but only after multiple waves of fast growth separated by periods of low reactivity, with up to ∼11% total mass gain before passivation. The largest carbon black and graphitic NPs, with Minitial >50 MDa, grew rapidly and continuously, adding up to ∼300% of Minitial with no sign of rate slowing as long as C2H2 was present. The efficiencies for C2H2 addition and etching by O2 are strongly correlated, but the correlation changes as the NPs passivate. Growth and passivation mechanisms are discussed.

Chemistry↗
DOE OSTI2025

Molecular Origins of Temperature-Dependent X-ray Absorption in YAG:Dy

The absorption and emission of X-rays in dysprosium-doped yttrium aluminum garnet (YAG:Dy) has produced unexpected thermographic behavior, which is investigated using a combination of finite temperature ab initio molecular dynamic simulations, structural characterization, and electronic structure calculations of X-ray characteristics. Calculated average peak X-ray absorption spectra (XAS) from simulations between 300 and 600 K result in peak intensity loss due to thermalization effects, matching experimentally measured behavior of YAG:Dy. Here, investigation of atomic snapshots indicates structural factors that correlated with the X-ray behavior, with the first Y–O coordination sphere identified as the primary structural feature unique to high XAS intensity as calculated by radial and pair distribution functions.

Ab initio molecular dynamics↗
NASA NTRS1985

Orientation and temperature dependence of some mechanical properties of the single-crystal nickel-base superalloy Rene N4. 3: Tension-compression anisotropy

Single crystal superalloy specimens with various crystallographic directions along their axes were tested in compression at room temperature, 650, 760, 870, and 980 deg C. These results are compared with the tensile behavior studied previously. The alloy, Rene N4, was developed for gas turbine engine blades and has the nominal composition 3.7 Al, 4.2 Ti, 4 Ta, 0.5 Nb, 6 W, 1.5 Mo 9 Cr. 7.5 Co, balance Ni, in weight percent. Slip trace analysis showed that primary cube slip occurred even at room temperature for the 111 specimens. With increasing test temperature more orientations exhibited primary cube slip, until at 870 deg C only the 100 and 011 specimens exhibited normal octahedral slip. The yield strength for octahedral slip was numerically analysed using a model proposed by Lall, Chin, and Pope to explain deviations from Schmid's Law in the yielding behavior of a single phase Gamma prime alloy, Ni3(Al, Nb). The Schmid's Law deviations in Rene N4 were found to be largely due to a tension-compression anisotropy. A second effect, which increases trength for orientations away from 001, was found to be small in Rene N4. Analysis of recently published data on the single crystal superalloy PWA 1480 yielded the same result.

Miner, R. V.↗
NASA NTRS1997

Electron-Temperature Dependence of the Recombination of NH4(+)((NH3)(sub n) Ions with Electrons

The two-body recombination of NH4(+)(NH3)(sub 2,3) cluster-ions with electrons has been studied in an afterglow experiment in which the electron temperature T, was elevated by radio-frequency heating from 300 K up to 900 K. The recombination coefficients for the n = 2 and n = 3 cluster ions were found to be equal, alpha(sub 2, sup(2)) = alpha(sub 3, sup(2)) = (4.8 +/- 0.5) x 10(exp - 6)cu cm/s, and to vary with electron temperature as T(sub c, sup -0.65) rather than to be nearly temperature-independent as had been inferred from measurements in microwave-heated plasmas.

Skrzypkowski, M. P.↗
NASA NTRS2007

Pressure and Temperature Dependence of the Reaction of Vinyl Radical with Ethylene

This work reports measurements of absolute rate coefficients and Rice-Ramsperger-Kassel-Marcus (RRKM) master equation simulations of the C2H3 + C2H4 reaction. Direct kinetic studies were performed over a temperature range of 300-700 K and pressures of 20 and 133 mbar. Vinyl radicals (H2C=CH) were generated by laser photolysis of vinyl iodide (C2H31) at 266 nm, and time-resolved absorption spectroscopy was used to probe vinyl radicals through absorption at 423.2 nm. Measurements at 20 mbar are in good agreement with previous determinations at higher temperature. A weighted three-parameter Arrhenius fit to the experimental rate constant at 133 mbar, with the temperature exponent fixed, gives k = (7 +/- 1) x 10(exp -l4) cu cm/molecule/s (T/298 K)(exp 2) exp[-(1430 +/- 70) K/T]. RRKM master equation simulations, based on G3 calculations of stationary points on the C4H7 potential energy surface, were carried out to predict rate coefficients and product branching fractions. The predicted branching to 1-methylallyl product is relatively small under the conditions of the present experiments but increases as the pressure is lowered. Analysis of end products of 248 nm photolysis of vinyl iodide/ethylene mixtures at total pressures between 27 and 933 mbar provides no direct evidence for participation of I -methylallyl.

Ismail, Huzeifa↗
NASA NTRS1981

Temperature dependence of ozone absorption cross section, 280 to 330 nm

A description is presented of the results of an analysis of the presently available data on the variation of the ozone absorption cross section and the O(1D) yield with temperature. The data used in the analysis of the total ozone cross section were obtained by Inn and Tanaka (1953), Vigroux (1953), and Simons et al. (1973). The O(1D) yield data examined include those of Moortgat et al. (1977), Arnold et al. (1977), and Brock and Watson (1980). For the purposes of the analysis the yield measurements were converted to partial cross sections by multiplying the published yield by the published total cross section.

Hudson, R. D.↗
NASA NTRS1991

Temperature dependence of the elastic moduli and damping for polycrystalline LiF-22 pct CaF2 eutectic salt

Young's and shear moduli and damping were measured for as-cast polycrystalline LiF-(22 mol pct)CaF2 eutectic specimens as a function of temperature using the piezoelectric ultrasonic composite oscillator technique. The shear modulus decreased with increasing temperature from about 40 GPa at 295 K to about 30 GPa at 1000 K, while the Young modulus decreased from about 115 GPa at 295 K to about 35 GPa at 900 K. These values are compared with those derived from the rule of mixtures using elastic moduli data for LiF and CaF2 single crystals. It is shown that, while the shear modulus data agree reasonably well with the predicted trend, there is a large discrepancy between the theoretical calculations and the Young modulus values, where this disagreement increases with increasing temperature.

Wolfenden, A.↗
NASA NTRS1994

Temperature Dependent Performance of Coplanar Waveguide (CPW) on Substrates of Various Materials

The attenuation (a) and effective dielectric constant (E(sub eff)) of Coplanar Waveguide (CPW) transmission lines on high-resistivity silicon and diamond substrates as a function of both temperature and frequency are presented. The technique used to obtain the values for a and E(sub eff) involves the use of a unique cryogenic probe station designed and built by NASA. Attenuation of gold CPW lines on diamond substrates is compared with that of superconducting CPW lines.

Taub, Susan R.↗
NASA NTRS1986

Orientation and temperature dependence of some mechanical properties of the single-crystal nickel-base superalloy Rene N4. I - Tensile behavior

Single crystal specimens of a nickel-base superalloy with axes near 001, 011, and -112 were tested in tension at room temperature, 760, and 980 C. The alloy Rene N-4, was developed for gas turbine engine blades and has the nominal composition 3.7 Al, 4.2 Ti, 4 Ta, 0.5 Nb, 6 W, 1.5 Mo, 9 Cr, 7.5 Co, balance Ni, (all in weight percent). Analysis of slip band traces, specimen axis rotation, and dislocation Burgers vectors showed that at 760 and 980 C primary cube slip supplanted normal octahedral slip for the -112 line-oriented specimens. The other two orientations, which have lower resolved shear stresses on the cube system, exhibited octahedral slip at all three temperatures. The critical resolved shear stress is considerably greater on the cube system than on the octahedral system at room temperature. However, at 760 and 980 C the critical resolved shear stresses on the two systems are about the same. While the room temperature and 980 C yield strengths for the two orientations exhibiting octahedral slip could be rationalized on the basis of resolved shear stress, those at 760 C could not. Such violations of Schmid's law have previously been observed in other superalloys and single phase gamma-prime.

Miner, R. V.↗