Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “temperature acceleration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

Thermoregulation in unrestrained rats during and after exposure to 1.5-4 G

Unrestrained rats were exposed to cold for 1 h during and immediately after exposure to hypergravic fields (1.5-4 G) to determine if they recover their ability to thermoregulate on reentry to 1-G conditions. In contrast to the decreased body temperatures observed when cold exposure occurred concurrently with acceleration, hypothalamic, carotid, and brown fat temperatures did not fall when rats were exposed to cold immediately after return to 1 G. These results support the hypothesis that the thermoregulatory alterations seen under hypergravic conditions are manifestations of an effect of ongoing exposure to hypergravity and can be reversed on termination of acceleration. The reversibility of the thermoregulatory impairment is apparently unaffected by the magnitude of the acceleration field over a range of 1.5-4 G.

Giacchino, J.↗

Suppressing Thermal Energy Drift In The LLNL Flash X-Ray Accelerator Using Linear Disk Resistor Stacks

This paper addresses thermal drift in sodium thiosulfate liquid resistors and their replacement with linear disk resistors from HVR Advanced Power Components. Sodium thiosulfate resistors in the FXR induction linear accelerator application have a temperature coefficient of {approx}1.8%/C. The FXR Marx banks send an 8kJ pulse through eight 524 cm{sup 3} liquid resistors at a repetition rate of up to 1 every 45 seconds. Every pulse increases the temperature of the solution by {approx}0.4 C which produces a 0.7% change in resistance. The typical cooling rate is {approx}0.4 C per minute which results in {approx}0.1% energy drop per pulse during continuous pulsed operations. A radiographic accelerator is extraordinarily sensitive to energy variations. Changes in beam energy produce movement in beam transport, changes in spot size, and large dose variations. If self-heating were the only problem, we could predict the increase in input voltage required to compensate for the energy loss. However, there are other variables that influence the temperature of the resistors such as focus magnet heating, changes in room temperature, changes in cooling water, where the cell is located, etc. Additionally not all of the resistors have equivalent cooling rates and as many as 32 resistors are driven from a single power source. The FXR accelerator group elected to replace the sodium thiosulfate resistors with HVR Linear Disk Resistors in a stack type configuration. With data limited for these resistors when used in oil and at low resistance values, a full characterization needed to be performed. High currents (up to 15kA), high voltages (up to 400kV), and Fast Rise times (<10ns) made a resistor choice difficult. Other solid resistors have been tried and had problems at the connection points and with the fact that the resistivity changed as they absorbed oil. The selected HVR resistors have the advantage of being manufactured with the oil impregnated in to them so this characteristic is minimized while still offering the desired low temperature coefficient of resistance compared to sodium thiosulfate. The characterization experiments and comparison with the sodium thiosulfate liquid resistors will be fully discussed and the final design described.

42 ENGINEERING↗

Dose Rate Effects on Degradation of Nuclear Power Plant Electrical Cable Insulation at a Common Dose

The intent of this report is to address an identified knowledge gap in relating accelerated aging of nuclear electrical cables to service aging: dose rate effects (DRE). Here, DRE refer to gamma radiation-induced polymer degradation being a function of dose rate in addition to total absorbed dose. The concern raised is that historical qualification conducted at higher dose rates to simulate service lifetime may underestimate insulation degradation that occurs at lower dose rates in service. In the work described herein, common nuclear cable insulation materials—cross-linked polyethylene (XLPE) and ethylene propylene diene elastomer (EPDM)—were subjected to accelerated aging at ambient temperature (26°C) at different gamma dose rates of 100, 200 and 1800 Gy/h for select exposure durations to achieve constant total doses of 170, 210 and 300 kGy to evaluate DRE. First, the cable insulation material types investigated are described. Then, the accelerated aging experimental process involving gamma irradiation applied to the insulation specimens at room temperature and different dose rates is discussed. Then, the experimental characterization techniques used to perform this work are elucidated. These include elongation at break (EAB), mass change, yellowness index (YI), carbonyl index (CI), density, indenter modulus (IM), and relaxation constant (t). Theory of polymer degradation is discussed, and characterization results and discussion are provided. Finally, concluding remarks are made. The findings from this work and cited prior work reveal that DRE are material dependent, even between similar material categories (e.g., XLPE). In the case of the EPDM studied, degradation of ductility was observed to be greater at higher dose rate for the same total dose, indicating accelerated gamma aging to be more conservative than extended aging. Thus, conclusions regarding the conservatism of historical qualification likely require additional consideration for specific materials and conditions in question. The results of this study support the contention that, due to inherent limitations and uncertainties associated with prediction of cable remaining useful life from accelerated aging experiments, trending of installed cable insulation health status will be more practical and useful for safe and efficient cable aging management repair and replace decisions than lifetime prediction from historical qualification. The combination of material robustness demonstrated by the qualification process and ongoing monitoring of cable health status combine to provide confidence in continued safe use of existing nuclear cables. Additional research into effective and efficient condition monitoring methods for non-destructive evaluation of installed cables is needed to support aging cable management, including material studies to inform interpretation of measured results.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

SMART Cables for Observing the Global Ocean: Science and Implementation

The ocean is key to understanding societal threats including climate change, sea level rise, ocean warming, tsunamis, and earthquakes. Because the ocean is difficult and costly to monitor, we lack fundamental data needed to adequately model, understand, and address these threats. One solution is to integrate sensors into future undersea telecommunications cables. This is the mission of the SMART subsea cables initiative (Science Monitoring And Reliable Telecommunications). SMART sensors would “piggyback” on the power and communications infrastructure of a million kilometers of undersea fiber optic cable and thousands of repeaters, creating the potential for seafloor-based global ocean observing at a modest incremental cost. Initial sensors would measure temperature, pressure, and seismic acceleration. The resulting data would address two critical scientific and societal issues: the long-term need for sustained climate-quality data from the under-sampled ocean (e.g., deep ocean temperature, sea level, and circulation), and the near-term need for improvements to global tsunami warning networks. A Joint Task Force (JTF) led by three UN agencies (ITU/WMO/UNESCO-IOC) is working to bring this initiative to fruition. This paper explores the ocean science and early warning improvements available from SMART cable data, and the societal, technological, and financial elements of realizing such a global network. Simulations show that deep ocean temperature and pressure measurements can improve estimates of ocean circulation and heat content, and cable-based pressure and seismic-acceleration sensors can improve tsunami warning times and earthquake parameters. The technology of integrating these sensors into fiber optic cables is discussed, addressing sea and land-based elements plus delivery of real-time open data products to end users. The science and business case for SMART cables is evaluated. SMART cables have been endorsed by major ocean science organizations, and JTF is working with cable suppliers and sponsors, multilateral development banks and end users to incorporate SMART capabilities into future cable projects. By investing now, we can build up a global ocean network of long-lived SMART cable sensors, creating a transformative addition to the Global Ocean Observing System.

54 ENVIRONMENTAL SCIENCES↗

Observation of particle acceleration in laboratory magnetosphere

The self-organization of magnetospheric plasma is brought about by inward diffusion of magnetized particles. Not only creating a density gradient toward the center of a dipole magnetic field, the inward diffusion also accelerates particles and provides a planetary radiation belt with high energy particles. Here, we report the first experimental observation of a “laboratory radiation belt” created in the ring trap 1 device. By spectroscopic measurement, we found an appreciable anisotropy in the ion temperature, proving the betatron acceleration mechanism which heats particles in the perpendicular direction with respect to the magnetic field when particles move inward. The energy balance model, including the heating mechanism, explains the observed ion temperature profile.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Methyl formate oxidation kinetics up to 100 atm

Methyl formate (MF, CH3OCHO), the simplest ester, is a representative oxygenated fuel with high oxygen content, and low sooting tendency. However, its oxidation behavior under high-pressure and intermediate-temperature conditions remains insufficiently understood, especially where low-temperature peroxy radical chemistry, methanol chemistry, and pressure-dependent reaction pathways play a critical role. In this study, MF oxidation experiments were conducted in the Princeton supercritical-pressure jet-stirred reactor (SP-JSR) at 20 and 100 atm over the temperature range of 400–950 K under both fuel-lean and fuel-rich conditions. Based on the experimental results, an updated HP-Mech was developed by incorporating previous MF sub-mechanisms, expanded low-temperature peroxy pathways, and evaluated pressure-dependent decomposition kinetics. The newly updated HP-Mech shows greatly improved performance in predicting the onset temperature, the key intermediate species fractions, methanol formation, and the progression of MF oxidation across all the experimental conditions. Path flux analysis indicates that MF consumption at the onset stage is dominated by H-abstraction at the methyl site, forming CH2OCHO radicals that lead to the formation and isomerization of O2CH2OCHO, driving low-temperature chain propagation. Moreover, H-abstraction at the formate site forms CH3OCO radicals that preferentially decompose to CH3, initiating the methanol formation pathway linked to CH3O2 and HO2 chemistry. At the same time, HO2 formation is strongly coupled to MF oxidation through multiple MF-derived radical pathways. HCO originates from MF oxidation and acts as a key coupling species linking fuel consumption to HO2 buildup, especially under high-pressure and intermediate-temperature conditions. In addition to this dominant channel, supplementary HO2 formation pathways involving CH3, CH3O, CH2OH, and CH3O2 reacting with O2 further connect methanol chemistry and oxygenated radical chemistry to the HO2 pool, indicating the central role of HO2 in governing MF oxidation. Sensitivity analysis identifies MF with OH/HO2/CH3O2 reactions and the HO2/H2O2/OH sequence as the key factors controlling reactivity in the high-pressure and intermediate-temperature regime. MF directly reacts with OH/HO2/CH3O2 to consume the fuel and produce reactive radicals like CH2OCHO and CH3OCO that undergo subsequent oxidation pathways. Moreover, HO2 recombination suppresses oxidation at lower temperatures, while thermal decomposition of H2O2 accelerates OH production and promotes fuel consumption as temperature increases. The direct formation of active OH from HO2 radicals further completes the mechanism, improving its prediction especially during the oxidation onset stage.

Low-temperature Chemistry↗

THE NEW DESIGN FOR CAPTURE CAVITY OF CEBAF

In CEBAF, the electron beam from the injector must be sufficiently relativistic to match a 1 GeV recirculated beam in the first linac. The electron beam is produced with a ~130 keV electron gun, then accelerated by a room temperature, graded-beta standing wave linac, capture section, from 130 keV to 510 keV before enters two 5-cell superconducting RF cavities for further acceleration. Present capture cavity is a 5-cell side-coupled cavity. We designed a new slot-coupled cavity which has lower power consumption and more compact size.

Wang, Shaoheng↗

low-Cost, High-Performance Alternatives for Target Temperature Monitoring Using the Near-Infrared Spectrum

A process is being developed for commercial production of the medical isotope Mo-99 through a photo-nuclear reaction on a Mo-100 target using a highpower electron accelerator. This process requires temperature monitoring of the window through which a high-current electron beam is transmitted to the target. For this purpose, we evaluated two near infrared technologies: the OMEGA Engineering iR2 pyrometer and the Ocean Optics Maya2000 spectrometer with infrared-enhanced charge-coupled device (CCD) sensor. Measuring in the near infrared spectrum, in contrast to the long-wavelength infrared spectrum, offers a few immediate advantages: (1) ordinary glass or quartz optical elements can be used; (2) alignment can be performed without heating the target; and (3) emissivity corrections to temperature are typically less than 10%. If spatial resolution is not required, the infrared pyrometer is attractive because of its accuracy, low cost, and simplicity. If spatial resolution is required, we make recommendations for near-infrared imaging based on our data augmented by calculations

47 OTHER INSTRUMENTATION↗

Record High Ramping Rates in HTS Based Superconducting Accelerator Magnet

Here we report results of experimental test of the High Temperature Superconductor (HTS) based fast-cycling prototype accelerator magnet capable to operate up to about 300 T/s field ramping rate with some 0.5 T B-field in the magnet gap. The measured upper limit for the cryogenic cooling power required to support magnet conductor operation at high ramping rates indicates great potential for such type of magnets in rapid cycling synchrotrons for neutrino research or acceleration of very short-lived muons. The test magnet design, construction and supporting cryogenic and power systems are briefly described. The magnet's power test results are discussed in terms of a possible upgrade of this magnet design to 2 T B-field, a maximum feasible with super-ferric magnet.

43 PARTICLE ACCELERATORS↗

Modeling Microwave-Enhanced Chemical Vapor Infiltration Process for Preventing Premature Pore Closure

The chemical vapor infiltration (CVI) process involves infiltrating a porous preform with reacting gases that undergo chemical transformation at high temperatures to deposit the ceramic phase within the pores, ultimately leading to a dense composite. The conventional CVI process in composite manufacturing needs to follow an isothermal approach to minimize temperature differences between the external and internal surfaces of the preform, ensuring that reactive gases infiltrate internal pores before external surfaces seal. Here, this study addresses the challenge of premature pore closure in CVI processes through microwave heating. A frequency-domain microwave solver is developed in OpenFOAM to investigate volumetric heating mechanisms within the preform. Through numerical studies, we demonstrate the capability of microwave heating of creating an inside-out temperature inversion. This inversion accelerates reactions proximal to the preform center, effectively mitigating the risk of premature external pore closure and ensuring uniform densification. The results reveal a significant enhancement in temperature inversion when high-permittivity reflectors are incorporated to generate resonant waves. This microwave heating strategy is then coupled with high-fidelity direct numerical simulation (DNS) of reacting flow, enabling the analysis of resulting densification processes. The DNS includes detailed chemistry and realistic diffusion coefficients. The numerical results can be used to estimate the impact of microwave-induced temperature inversion on densification in productions.

42 ENGINEERING↗

Modeling Microwave-Enhanced Chemical Vapor Infiltration Process for Preventing Premature Pore Closure

The chemical vapor infiltration (CVI) process involves infiltrating a porous preform with reacting gases that undergo chemical transformation at high temperatures to deposit the ceramic phase within the pores, ultimately leading to a dense composite. The conventional CVI process in composite manufacturing needs to follow an isothermal approach to minimize temperature differences between the external and internal surfaces of the preform, ensuring that reactive gases infiltrate internal pores before external surfaces seal. This study addresses the challenge of premature pore closure in CVI processes through microwave heating. A frequency-domain microwave solver is developed in Open-FOAM to investigate volumetric heating mechanisms within the preform. Through numerical studies, we demonstrate the capability of microwave heating of creating an inside-out temperature inversion. This inversion accelerates reactions proximal to the preform center, effectively mitigating the risk of premature external pore closure and ensuring uniform densification. The results reveal a significant enhancement in temperature inversion when high-permittivity reflectors are incorporated to generate resonant waves. This microwave heating strategy is then coupled with high-fidelity direct numerical simulation (DNS) of reacting flow, enabling the analysis of resulting densification processes. The DNS simulation includes detailed chemistry and realistic diffusion coefficients. The numerical results can be used to estimate the impact of microwave-induced temperature inversion on densification in productions.

Ge, Wenjun↗

Water of Hydration Dynamics in Minerals Gypsum and Bassanite: Ultrafast 2D IR Spectroscopy of Rocks

Water of hydration plays an important role in minerals, determining their crystal structures and physical properties. In this work, ultrafast nonlinear infrared (IR) techniques, twodimensional infrared (2D IR) and polarization selective pump-probe (PSPP) spectroscopies, were used to measure the dynamics and disorder of water of hydration in two minerals, gypsum (CaSO 4 ·2H 2 O) and bassanite (CaSO 4 ·0.5H 2 O). 2D IR spectra revealed that water arrangement in freshly precipitated gypsum contained a small amount of inhomogeneity. Following annealing at 348 K, water molecules became highly ordered; the 2D IR spectrum became homogeneously broadened (motional narrowed). PSPP measurements observed only inertial orientational relaxation. In contrast, water in bassanite’s tubular channels is dynamically disordered. 2D IR spectra showed a significant amount of inhomogeneous broadening caused by a range of water configurations. At 298 K, water dynamics cause spectral diffusion that sampled a portion of the inhomogeneous linewidth on the timescale of ~30 ps, while the rest of inhomogeneity is static on the time scale of the measurements. At higher temperature, the dynamics become faster. Spectral diffusion accelerates, and a portion of the lower temperature spectral diffusion became motionally narrowed. At sufficiently high temperature, all of the dynamics that produced spectral diffusion at lower temperatures became motionally narrowed and only homogeneous broadening and static inhomogeneity were observed. Water angular motions in bassanite exhibit temperaturedependent diffusive orientational relaxation in a restricted cone of angles. The experiments were made possible by eliminating the vast amount of scattered light produced by the granulated powder samples using phase cycling methods.

14 SOLAR ENERGY↗

Investigation and modeling of the degradation of zirconium-based fuel cladding during corrosion in steam and air-steam mixtures at high temperatures - 2016-0033

This paper presents the main results of a study conducted to quantify and to model the degradation state of zirconium-based fuel claddings submitted to severe-accident conditions in a nuclear reactor core: high temperatures and either pure steam or an air-steam mixture. Due to the progressive thickening of a dense and protective ZrO{sub 2} layer, the oxidation kinetics of zirconium-based claddings in steam at high temperatures typical of severe nuclear accidents are generally cubic or parabolic. However, for some temperature domains, this oxide layer may crack, becoming porous and no longer protective. In these 'breakaway' conditions, the oxidation kinetics change from (sub)parabolic to linear or even accelerated. In addition, the temperature increase can lead core materials to melt and to relocate down to the vessel lower head, threatening its integrity. If it fails, and for specific conditions, air ingress may take place into the reactor. Hence, oxygen and nitrogen both react with zirconium-based claddings successively through the oxidation of zirconium (forming a ZrO{sub 2} layer), nitriding of zirconium (forming zirconium nitride particles), and the oxidation of zirconium nitride (forming ZrO{sub 2} and releasing nitrogen). These self-sustained chemical reactions enhance the deterioration of zirconium-based claddings and their ZrO{sub 2} layers, inducing an increase in their open porosity. To quantify this porosity, a series of two-step experiments was conducted. First, ZIRLO{sup TM} cladding samples were isothermally oxidized in pure steam or in a 50:50 mol% air-steam mixture at several different temperatures and durations. The main thermal effects on reaction kinetics and the high impact of air on the cladding degradation were all confirmed by experimental results. Second, pioneering porosimetry measurements by mercury intrusion were realized for the first time on such corroded cladding samples. In both atmospheres, it was pointed out that 1,200 and 1,250 K led to particularly porous oxide layers, especially due to strong breakaway effects. Moreover, we confirmed that the presence of air strongly enhances the oxide cracking: cladding samples were more porous when oxidized in the air-steam mixture than under pure steam. Finally, we observed that in all conditions, the open porous volume fraction of ZIRLO claddings continuously rose during their corrosion process. Hence, for each experimental condition, porosity correlations were determined through linear regressions, and porosity increase rates were deduced by derivation versus time and validated against porosimetry results of cladding samples corroded in transient nonisothermal) conditions. (authors)

36 MATERIALS SCIENCE↗

DEGRADATION IN PERFORMANCE OF LANTHANUM STRONTIUM MANGANITE BASED SOLID OXIDE FUEL CELL CATHODES UNDER ACCELERATED TESTING

The performance of solid oxide fuel cells (SOFCs) with three different lanthanum strontium manganite (LSM) based cathode compositions were evaluated. All cells were yttria-stabilized zirconia (Zr0.92Y0.08O2-δ, 8YSZ) electrolyte-supported button cells, consisting of a nickel oxide – yttria-stabilized zirconia (NiO-8YSZ) anode and a cathode of 8YSZ and LSM. The three LSM compositions differed in the amount of excess Mn: Composition A was (La0.85Sr0.15)0.90MnO3±δ (10% excess Mn); Composition B was (La0.80Sr0.20)0.95MnO3±δ (5% excess Mn); and Composition C was (La0.80Sr0.20)0.98MnO3±δ (2% excess Mn). The cells were tested under conventional and accelerated conditions, where the accelerated conditions were meant to simulate the results of months of long-term testing in just 500 hours (approximately three weeks) of testing by using high operating temperature and current density. Accelerated tests showed lower degradation rates, lower continuous area specific resistance (ASR), and higher power output than conventional tests for all cathode compositions. Continuous measurements of the cells' output voltage versus time, together with periodic electrochemical impedance spectroscopy (EIS) measurements, were used to evaluate the performance of the cells in terms of ASR degradation rates (% ASR rise per kh) and power outputs. The EIS measurements also permitted a partial deconvolution of the cathode ASR from the anode ASR. Cathodes with 10% excess Mn tested under accelerated conditions had the lowest degradation rates, but the highest continuous ASR and lowest power outputs. Cathodes with 2% excess Mn tested under accelerated conditions had the lowest continuous ASR and highest power outputs; thus it was concluded that cells with the lowest amount of excess Mn cathodes performed the best.

08 HYDROGEN↗

Low Temperature Structural Phase Transition of Ba3NaIr2O9

Single crystal X-ray and synchrotron X-ray powder diffraction have been used to probe the structure of Ba3NaIr2O9 from 300 K down to 20 K. Ba3NaIr2O9 is found to undergo a structural transition from hexagonal symmetry, P63/mmc, at ambient temperature to monoclinic symmetry, C2/c, at low temperature. The evolution of the unit cell volume upon cooling is indicative of a higher order structural transition, and the symmetry breaking becomes apparent as the temperature is decreased. The low temperature monoclinic structure of Ba3NaIr2O9 contains strongly distorted [NaO6] and [IrO6] octahedra in comparison to the room temperature hexagonal structure.

43 PARTICLE ACCELERATORS↗

Superconductor Requirements and Characterization for High Field Accelerator Magnets

The 2014 Particle Physics Project Prioritization Panel (P5) strategic plan for U.S. High Energy Physics (HEP) endorses a continued world leadership role in superconducting magnet technology for future Energy Frontier Programs. This includes 10 to 15 T Nb 3 Sn accelerator magnets for LHC upgrades and a future 100 TeV scale pp collider, and as ultimate goal that of developing magnet technologies above 20 T based on both High Temperature Superconductors (HTS) and Low Temperature Superconductors (LTS) for accelerator magnets. To achieve these objectives, a sound conductor development and characterization program is needed and is herein described. This program is intended to be conducted in close collaboration with U.S. and International labs, Universities and Industry.

43 PARTICLE ACCELERATORS↗

Electrofluidic accelerometer

Electrofluidic accelerometer senses components of linear and angular acceleration field. Typical application of such acceleration is as active controlling element in airplane autopilot. In contrast to conventional accelerometers, electrofluidic accelerometer is lightweight, small, inexpensive, rugged, and requires little power. It consists of two temperature sensors on opposite sides of heating element. Sensors detect temperature gradient created by acceleration field on fluid; when device is accelerated, gradient changes because of bouyant force on hotter (thus lighter) portion of fluid.

Hewes, D. E.↗