Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface roughness”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

Modeling Spectral Degradation of MODIS and VIIRS Solar Diffusers

Solar diffusers (SDs) onboard the Moderate Resolution Imaging Spectroradiometer (MODIS) on Terra and Aqua spacecraft and the Visible Infrared Imaging Radiometer Suite (VIIRS) on SNPP and NOAA-20 spacecraft have been used as the primary onboard radiometric calibrator for reflective solar bands and their spectral reflectance is known to degrade on-orbit. All of the solar diffusers on these instrument show faster degradation of reflectance in the 0.4 to 0.6 µm channels than the longer wavelength channels. The spectral degradation of these SDs is due to the surface roughness growth under the exposure to solar UV and energetic particle radiation in space. In this paper, the origin of SD degradation is modeled by the physics-based Surface Roughness-induced Rayleigh Scattering (SRRS) model. The longterm growths of surface roughness of the SD on these instruments are characterized to show the consistency of SD roughness growth rates between Terra/Aqua MODIS and SNPP/NOAA-20 VIIRS. There was coincidental flattening or reverse in the growth trend of the surface roughness for the Terra/Aqua MODIS and SNPP VIIRS SDs, which can be due to the space weather variation. The applicability of the SRRS model is demonstrated with the long term spectral reflectance data from independent spaceborne SDs.

Calibration↗
NASA NTRS1991

Two-dimensional Navier-Stokes heat transfer analysis for rough turbine blades

A quasi-three-dimensional thin-layer Navier-Stokes analysis was used to predict heat transfer to rough surfaces. Comparisons are made between predicted and experimental heat transfer for turbine blades and flat plates of known roughness. The effect of surface roughness on heat transfer was modeled using a mixing length approach. The effect of near-wall grid spacing and convergence criteria on the accuracy of the heat transfer predictions are examined. An eddy viscosity mixing length model having an inner and outer layer was used. A discussion of the appropriate model for the crossover between the inner and outer layers is included. The analytic results are compared with experimental data for both flat plates and turbine blade geometries. Comparisons between predicted and experimental heat transfer showed that a modeling roughness effects using a modified mixing length approach results in good predictions of the trends in heat transfer due to roughness.

Boyle, R. J.↗
NASA NTRS1991

Two-dimensional Navier-Stokes heat transfer analysis for rough turbine blades

A quasi-three-dimensional thin-layer Navier-Stokes analysis was used to predict heat transfer to rough surfaces. Comparisons are made between predicted and experimental heat transfer for turbine blades and flat plates of known roughness. The effect of surface roughness on heat transfer was modeled using a mixing length approach. The effect of near-wall grid spacing and convergence criteria on the accuracy of the heat transfer predictions are examined. An eddy viscosity mixing length model having an inner and outer layer was used. A discussion of the appropriate model for the crossover between the inner and outer layers is included. The analytic results are compared with experimental data for both flat plates and turbine blade geometries. Comparisons between predicted and experimental heat transfer showed that a modeling roughness effects using a modified mixing length approach results in good predictions of the trends in heat transfer due to roughness.

Boyle, R. J.↗
NASA NTRS2003

Ceramic Strain Gages for Use at Temperatures up to 1500 Celsius

Indium-tin-oxide (ITO) thin film strain gages were successfully demonstrated at temperatures beyond 1500 C. High temperature static strain tests revealed that the piezoresistive response and electrical stability of the ceramic sensors depended on the thickness of the ITO films comprising the active strain elements. When 2.5 microns-thick ITO films were employed as the active strain elements, the piezoresistive response became unstable at temperatures above 1225 C. In contrast to this, ceramic sensors prepared with 5 microns-thick ITO were stable beyond 1430 C and sensors prepared with 8 microns-thick ITO survived more than 20 hr of operation at 1481 C. Very thick (10 microns) ITo strain gages were extremely stable and responsive at 1528 C. ESCA depth profiles confirmed that an interfacial reaction between the ITO strain gage and alumina substrate was responsible for the high temperature electrical stability observed. Similar improvements in high temperature stability were achieved by doping the active ITO strain elements with aluminum. Several Sic-Sic CMC constant strain beams were instrumented with ITO strain gages and delivered to NASA for testing. Due to the extreme surface roughness of the CMC substrates, new lithography techniques and surface preparation methods were developed. These techniques relied heavily on a combination of Sic and A12O3 cement layers to provide the necessary surface finish for efficient pattern transfer. Micro-contact printing using soft lithography and PDMS stamps was also used to successfully transfer the thin film strain gage patterns to the resist coated CMC substrates. This latter approach has considerable potential for transferring the thin film strain gage patterns to the extremely rough surfaces associated with the CMC's.

Gregory, Otto↗
NASA NTRS1993

An almost 'perfectly' diffuse, 'perfect' reflector for far-infrared reflectance calibration

Specular and diffuse reflectance measurements made near normal incidence of two very rough, solid aluminum surfaces are presented for the wavelength range from 2.2 to 512 microns. The diffuse measurements made at nonspecular angles by two different detectors indicate that between 33 and 201 microns the reflectance of one surface is nearly Lambertian (isotropic) with a bidirectional reflectance distribution function (BRDF) value within 32 percent of the theoretical value of (1/pi)/sr for a perfectly diffuse, perfect reflector. Photometric reflectance spectra at the specular angle show that between 6.9 and 100 microns the specular BRDF of these surfaces is within 5 percent of the theoretical value of (1/pi)/sr. At longer wavelengths of 235, 320, and 512 microns the specular reflectance rapidly departs from that of a perfectly diffuse, perfect reflector. The two samples studied have rms surface roughnesses of 44 and 60 microns. A durable metal surface with these near perfect reflectance characteristics can be advantageously used in the FIR as a black-body source, the interior surface of an integrating sphere, and most especially as an absolute calibration standard. BRDF measurements at 40 deg incidence, though still highly diffuse, show a significant departure from Lambertian reflectance.

Smith, Sheldon M.↗
NASA NTRS1994

An integrated optical CO2 sensor. Phase 0: Design and fabrication of critical elements

Significant progress has been made toward all of the goals for the first phase of the project short of actual fabrication of a light path. Two alternative approaches to fabricating gold mirrors using the basic LIGA process were developed, one using electroplated solid gold mirrors and the second using gold plated over a nickel base. A new method of fabrication, the transfer mask process, was developed and demonstrated. Analysis of the projected surface roughness and beam divergence effects was completed. With gold surface with low surface roughness scattering losses are expected to be insignificant. Beam divergence due to diffraction will require a modification of the original design, but should be eliminated by fabricating mirrors 1000 mu m in height by 1000 mu m in width and using a source with an initial beam radius greater than 300 mu m. This may eliminate any need for focusing optics. Since the modified design does not affect the mask layout, ordering of the mask and fabrication of the test structures can begin immediately at the start of Phase 1.

Murphy, Michael C.↗
NASA NTRS1994

An Experimental Study of the Aerodynamics of a Swept and Unswept Semispan Wing with a Simulated Glaze Ice Accretion

Two semispan wings, one with a rectangular planform and one with 30 degrees of leading edge sweep were tested. Both had a NACA 0012 airfoil section, and both were tested clean and with simulated glaze ice shapes on their leading edges. Several surface roughness were tested. Each model geometry is documented and each surface roughness is explained. Aerodynamic performance of the wing in the form of sectional lift and integrated three-dimensional lift is documented through pressure measurements obtained from rows of surface pressure taps placed at five span locations on the wing. For the rectangular wing, sectional drag near the midspan is obtained from wake total pressure profiles. The data is presented in tabular and graphical form and is also available on computer disk.

Bragg, Michael B.↗
NASA NTRS1989

Effects of nose bluntness, roughness, and surface perturbations on the asymmetric flow past slender bodies at large angles of attack

The effects of such geometric perturbations as variations of model-tip sharpness and roughness, as well as discrete surface perturbations, on the asymmetric flow past slender bodies is experimentally investigated for the cases of a cone/cylinder model having a 10-deg semiapex angle and a 3.0-caliber tangent ogive model. Both models have base diameters of 3.5 inches, and were tested in laminar flow conditions at angles-of-attack in the 30-60 deg range. Single, discrete roughness elements were represented by beads; bead effectiveness was judged on the basis of the extent to which they affected the flowfield in various conditions.

Moskovitz, Cary A.↗
NASA NTRS1972

Thermal characteristics of the moon.

The papers describe earth-based and in situ surface measurements of the thermal characteristics of lunar-type materials. A geophysical interpretation of the thermal history of the moon is given. Microwave emission from the moon and radar mapping of lunar surface roughness are studied. Lunar thermal aspects from Surveyor data, lunar surface temperatures from Apollo 11 data, the development of an in situ thermal conductivity measurement for the lunar heat flow experiment, and the Apollo 15 lunar heat flow measurement are reviewed. Thermal properties of granulated materials, thermal property measurements on lunar material returned by Apollo 11 and 12 missions, and thermal characteristics of lunar surface roughness are discussed. Individual items are abstracted in this issue.

Lucas, J. W.↗
NASA NTRS1985

Effect of counterface material type and its topography on the tribological properties of polyimide composites

Graphite fiber reinforced polyimide composite pins were slid against seven different counterfaces to determine the effect of material type on the tribological properties of polymer composites. In addition, the effect of sliding a new pin on a pre-established transfer film was investigated. The results indicated that almost a five order of magnitude difference in composite wear rate can occur just by varying the counterface material. An attempt to make all surfaces as smooth as possible was made, but due to differences in material composition this was not possible and a range of surface roughnesses were obtained. The results indicate that the smoother the surface, the lower the composite wear rate; but that small protrusions (not discernible with arithmetic surface roughness measurements) can markedly increase wear rates. A pre-established transfer film improved both run in and steady state wear rates.

Fusaro, R. L.↗
NASA NTRS1986

Counterface effects on the tribological properties of polyimide composites

Graphite fiber reinforced polyimide composite pins were slid against seven different counterfaces to determine the effect of material type on the tribological properties of polymer composites. In addition, the effect of sliding a new pin on a pre-established transfer film was investigated. The results indicated that almost a five order of magnitude difference in composite wear rate can occur just by varying the counterface material. An attempt to make all surfaces as smooth as possible was made, but due to differences in material composition this was not possible and a range of surface roughnesses were obtained. The results indicate that the smoother the surface, the lower the composite wear rate; but that small protrusions (not discernible with arithmetic surface roughness measurements) can markedly increase wear rates. A pre-established transfer film improved both run in and steady state wear rates.

Fusaro, Robert L.↗
NASA NTRS2015

Transition Experiments on Blunt Bodies with Distributed Roughness in Hypersonic Free Flight in Carbon Dioxide

Blunt-body geometries were flown through carbon dioxide in the NASA Ames Hypervelocity Free Flight Aerodynamic Facility to investigate the influence of distributed surface roughness on transition to turbulence in CO2-dominated atmospheres, such as those of Mars and Venus. Tests were also performed in air for direct comparison with archival results. Models of hemispherical and spherically-blunted large-angle conical geometries were flown at speeds between 2.8 km/s and 5.1 km/s and freestream pressures between 50 Torr and 228 Torr. Transition fronts were determined from global surface heat flux distributions measured using thermal imaging techniques. Distributed surface roughness was produced by grit-blasting the model surfaces. Real-gas Navier-Stokes solutions were used to calculate non-dimensional correlating parameters at the measured transition onset locations. Transition-onset locations correlated well with a constant roughness Reynolds number based on the mean roughness element height. The critical roughness Reynolds number for transition onset determined for flight in CO2 was 223 +/- 25%. This mean value is lower than the critical value of 250 +/- 20% previously-established from tests conducted in air, but within the bounds of the expected measurement uncertainty.

ballistic ranges↗
NASA NTRS1983

Monte Carlo simulation of the effect of soil moisture variation on the microwave emission from soils

In this paper, results of a Monte Carlo simulation of the effect of noise on the relationship between the microwave emissivity of soil and its moisture content are presented. It is found that whenever the magnitude of the noise for the independent variable, in this case the soil moisture, is increased, both the slope of the regression and the correlation coefficient decrease. In particular, when the noise has magnitude equivalent to a coefficient of variation of 0.25, the slope and correlation coefficient are in good agreement with those obtained from the data of a 21-cm airborne microwave radiometer which was flown over a test site in hand county, South Dakota. The comparison was made using a linear relationship to determine the estimated emissivity from the ground measurements of soil moisture. The linear relationship was derived from a radiative transfer model calculation of the microwave emissivities using realistic soil-moisture profiles. The effect of surface roughness was included in the relationship, and the variability of the surface roughness was also simulated by a Monte Carlo technique.

Mo, T.↗
NASA NTRS2006

Effects of Laser and Shot Peening on Fatigue Crack Growth in Friction Stir Welds

The effects of laser, and shot peening on the fatigue life of Friction Stir Welds (FSW) have been investigated. The surface roughness resulting from various peening techniques was assessed, and the fracture surfaces microstructure was characterized. Laser peening resulted in an increase in fatigue life approximately 60%, while shot peening resulted in 10% increase when compared to the unpeened material. The surface roughness of shot peening was significantly higher compared to the base material, while specimens processed with laser peening were relatively smooth.

Hatamleh, Omar↗
NASA NTRS1989

Radiometry and a thermal modeling of asteroids

The steps required to determine a radiometric diameter of an asteroid from observations of its visual and thermal radiation are described together with thermal models required to predict the emission expected from a body of given size and bolometric albedo. It is pointed out, however, that, in some cases, these models were found to fail for a variety of reasons; in particular, they fail to characterize the shape, surface roughness, the rate and sense of rotation, and the maturity of the surface regolith, all of which affect the observed thermal flux. Several thermal models are examined, including the Standard Thermal Model for asteroids, the fast-rotating (isothermal-latitude) model, the thermophysical model, and the rough-surface thermophysical models.

Lebofsky, Larry A.↗
NASA NTRS1991

The application of differential roughness to mitigate friction and wear

By definition, differential roughness occurs where the surface roughness of one region is distinctly different from that of an adjacent region. Differential roughness may occur on a sliding surface when the structure of an area of the surface is modified relative to the original material. Differential roughness may be used to effect a film thickness change so as to cause hydrodynamic or hydrostatic lubrication effects just as if the surfaces were machined. The advantage of differential roughness is that the effective offset of film thickness continues to exist even if there is gross wear. One can effect film thickness changes which are smaller than can be made directly. Furthermore, asperity tip load support is the same over both the high roughness and small roughness regions. The potential uses for differential roughness are seals, bearings, and pumps. Some examples are presented.

Lebeck, Alan O.↗
NASA NTRS1984

Turbulent roughness drag due to surface waviness at low roughness Reynolds numbers

The current investigation has the objective to provide data which will make it possible to obtain a better estimate regarding the roughness drag for surface waviness. The data employed for this investigation were acquired in connection with a wavy wall study which was conducted as part of an overall program to reduce the skin friction of turbulent boundary layers in external flows. The results of the present investigation show that the low-speed roughness drag of small-amplitude sinusoidal wave trains having wavelengths of the order of the boundary-layer thickness is not only a function of h/lambda (h = total wave height, lambda = wavelength), but, in addition, is also a function of the roughness Reynolds number.

Lin, J. C.↗
NASA NTRSDate not supplied

Effect of Roughness on Transition on the BOLT-1a Geometry in Supersonic Flow

Infrared thermography measurements on an 8.8% scale BOLT-1a model were made in the NASA Langley Probe Calibration Tunnel for freestream unit Reynolds numbers from 7.7 × 10^ -6 /m to 30.7 × 10^ -6 /m, a freestream Mach number of 3.5, and nominal angle of attack of 0 degrees. The model was printed from polycarbonate and tested before and after fine-grit sanding to evaluate the effect of surface roughness on transition. Global surface roughness measurements were obtained using a 3D optical profilometer. The temperature distributions on the upper and lower experimental surfaces of the test article were simultaneously captured using two infrared cameras. Prior to testing, the facility’s freestream environment was characterized. At a freestream unit Reynolds number of approximately 17 × 10^ -6 /m, the nozzle-wall boundary layer began to transition non-uniformly, inducing transition on the model. The boundary-layer state was determined by analyzing Stanton number distributions computed from the surface temperature measurements. The present supersonic conditions that were examined on BOLT-1a were found to display both similarities and disparities in comparison to previous hypersonic experiments.

boundary layer transition↗